[PATCH] ARM: S3C24XX: Add .get_rate callback for "camif-upll" clock

[Kukjin Kim]

On 08/28/12 13:58, Sylwester Nawrocki wrote:
> On 08/28/2012 12:58 AM, Kukjin Kim wrote:
>> On 08/27/12 13:12, Sylwester Nawrocki wrote:
>>> Add missing get_rate callback for the "camif-upll" clock, so frequency
>>> of this clock is properly reported with clk_get_rate().
>>>
>>> Signed-off-by: Sylwester Nawrocki<sylvester.nawrocki at gmail.com>
>>> ---
>>> arch/arm/mach-s3c24xx/clock-s3c2440.c | 14 ++++++++++++++
>>> 1 files changed, 14 insertions(+), 0 deletions(-)
>>>
>>> diff --git a/arch/arm/mach-s3c24xx/clock-s3c2440.c
>>> b/arch/arm/mach-s3c24xx/clock-s3c2440.c
>>> index cb2883d..749220f 100644
>>> --- a/arch/arm/mach-s3c24xx/clock-s3c2440.c
>>> +++ b/arch/arm/mach-s3c24xx/clock-s3c2440.c
>>> @@ -87,6 +87,19 @@ static int s3c2440_camif_upll_setrate(struct clk
>>> *clk, unsigned long rate)
>>> return 0;
>>> }
>>>
>>> +static unsigned long s3c2440_camif_upll_getrate(struct clk *clk)
>>> +{
>>> + unsigned long parent_rate = clk_get_rate(clk->parent);
>>> + unsigned long camdivn = __raw_readl(S3C2440_CAMDIVN);
>>> +
>>> + if (!(camdivn&  S3C2440_CAMDIVN_CAMCLK_SEL))
>>> + return parent_rate;
>>> +
>>> + camdivn&= S3C2440_CAMDIVN_CAMCLK_MASK;
>>> +
>>> + return parent_rate / (camdivn + 1) / 2;
>>
>> Well, why do we need '/ 2' here?
>
> I simply followed documentation of the camera clock divider register
> (CAMDIVN). This is how CAMCLK_SEL and CAMCLK_DIV bit fields are described
> there:
>
> CAMDIVN      |  Bit  |       Description
> --------------------------------------------------------------------------
> CAMCLK_SEL   | [4]   | 0 : Use CAMCLK with UPLL output(CAMCLK=UPLL output)
>               |       | 1 : CAMCLK is divided by CAMCLK_DIV value
> -------------+-------+----------------------------------------------------
> CAMCLK_DIV   | [3:0] | CAMCLK divide factor setting register(0 – 15).
>               |       | Camera clock = UPLL / [(CAMCLK_DIV +1)x2].
>               |       | This bit is valid when CAMCLK_SEL=1.
>
> So, camera clock frequency = parent_rate / ((camdivn + 1) * 2).
> This is exactly same as 'parent_rate / ( camdivn + 1) / 2'.
>
> To be 1000% sure I compared frequency values reported from clk_get_rate()
> in the driver with values measured with an oscilloscope at the CAMCLKOUT
> pin. Everything was as expected (UPLL - 48 MHz, CAMCLKOUT - 12 MHz).
>
> Also, it's easy to confirm correctness of this code by inversing equations
> found in function s3c2440_camif_upll_setrate(), i.e.
>
>   camdivn&= ~(S3C2440_CAMDIVN_CAMCLK_SEL | S3C2440_CAMDIVN_CAMCLK_MASK);
>   if (rate != parent_rate) {
>   	camdivn |= S3C2440_CAMDIVN_CAMCLK_SEL;
>   	camdivn |= (((parent_rate / rate) / 2) - 1);
>   }
>
>   __raw_writel(camdivn, S3C2440_CAMDIVN);
>
> --

Looks OK, thanks for your reply :-)

Applied.

Best regards,
Kgene.
--
Kukjin Kim <kgene.kim at samsung.com>, Senior Engineer,
SW Solution Development Team, Samsung Electronics Co., Ltd.