[PATCH] spi/mxs: Make the SPI block clock speed configurable via DT

[Marek Vasut]

Add "clock-frequency" property, which allows configuring the SPI block's
base speed.

Signed-off-by: Marek Vasut <marex at denx.de>
Cc: Chris Ball <cjb at laptop.org>
Cc: Shawn Guo <shawn.guo at linaro.org>
Cc: Mark Brown <broonie at opensource.wolfsonmicro.com>
---
 Documentation/devicetree/bindings/spi/mxs-spi.txt |    4 ++++
 drivers/spi/spi-mxs.c                             |   21 +++++++++++++++------
 2 files changed, 19 insertions(+), 6 deletions(-)

diff --git a/Documentation/devicetree/bindings/spi/mxs-spi.txt b/Documentation/devicetree/bindings/spi/mxs-spi.txt
index c36296f..e2e1395 100644
--- a/Documentation/devicetree/bindings/spi/mxs-spi.txt
+++ b/Documentation/devicetree/bindings/spi/mxs-spi.txt
@@ -6,6 +6,10 @@ Required properties:
 - interrupts: Should contain SSP interrupts (error irq first, dma irq second)
 - fsl,ssp-dma-channel: APBX DMA channel for the SSP
 
+Optional properties:
+- clock-frequency : Input clock frequency to the SPI block in Hz.
+		    Default is 160000000 Hz.
+
 Example:
 
 ssp0: ssp at 80010000 {
diff --git a/drivers/spi/spi-mxs.c b/drivers/spi/spi-mxs.c
index 130a436..331f600 100644
--- a/drivers/spi/spi-mxs.c
+++ b/drivers/spi/spi-mxs.c
@@ -485,10 +485,17 @@ static int __devinit mxs_spi_probe(struct platform_device *pdev)
 	struct pinctrl *pinctrl;
 	struct clk *clk;
 	void __iomem *base;
-	int devid, dma_channel;
+	int devid, dma_channel, clk_freq;
 	int ret = 0, irq_err, irq_dma;
 	dma_cap_mask_t mask;
 
+	/*
+	 * Default clock speed for the SPI core. 160MHz seems to
+	 * work reasonably well with most SPI flashes, so use this
+	 * as a default. Override with "clock-frequency" DT prop.
+	 */
+	const int clk_freq_default = 160000000;
+
 	iores = platform_get_resource(pdev, IORESOURCE_MEM, 0);
 	irq_err = platform_get_irq(pdev, 0);
 	irq_dma = platform_get_irq(pdev, 1);
@@ -520,12 +527,18 @@ static int __devinit mxs_spi_probe(struct platform_device *pdev)
 				"Failed to get DMA channel\n");
 			return -EINVAL;
 		}
+
+		ret = of_property_read_u32(np, "clock-frequency",
+					   &clk_freq);
+		if (ret)
+			clk_freq = clk_freq_default;
 	} else {
 		dmares = platform_get_resource(pdev, IORESOURCE_DMA, 0);
 		if (!dmares)
 			return -EINVAL;
 		devid = pdev->id_entry->driver_data;
 		dma_channel = dmares->start;
+		clk_freq = clk_freq_default;
 	}
 
 	master = spi_alloc_master(&pdev->dev, sizeof(*spi));
@@ -561,12 +574,8 @@ static int __devinit mxs_spi_probe(struct platform_device *pdev)
 		goto out_master_free;
 	}
 
-	/*
-	 * Crank up the clock to 120MHz, this will be further divided onto a
-	 * proper speed.
-	 */
 	clk_prepare_enable(ssp->clk);
-	clk_set_rate(ssp->clk, 120 * 1000 * 1000);
+	clk_set_rate(ssp->clk, clk_freq);
 	ssp->clk_rate = clk_get_rate(ssp->clk) / 1000;
 
 	stmp_reset_block(ssp->base);
-- 
1.7.10.4