[PATCH] ARM: Kirkwood: Iomega ix2-200 DT support Signed-off-by: Alan M Butler <alanbutty12 at gmail.com>
Andrew Lunn
andrew at lunn.ch
Tue Aug 21 01:10:01 EDT 2012
On Mon, Aug 20, 2012 at 03:29:07PM +0100, Alan M Butler wrote:
> Patch version 5.
> Add support for the Iomega ix2-200.
> Led's and buttons working as of kernel 3.6-rc2
>
> the 3 lines in the network interface do seem to be required as
> removing either causes the network card to not be able to reach
> the network (at least on my device).
>
> Product page:
> http://go.iomega.com/en/products/network-storage-desktop/storcenter-network-storage-solution/network-hard-drive-ix2-200-cloud/?partner=4735#tech_specsItem_tab
>
> Signed-off-by: Alan M Butler <alanbutty12 at gmail.com>
>
> ---
> arch/arm/boot/dts/kirkwood-iomega_ix2_200.dts | 105 +++++++++++++++++++++++++
> arch/arm/mach-kirkwood/Kconfig | 7 ++
> arch/arm/mach-kirkwood/Makefile | 1 +
> arch/arm/mach-kirkwood/Makefile.boot | 1 +
> arch/arm/mach-kirkwood/board-dt.c | 4 +
> arch/arm/mach-kirkwood/board-iomega_ix2_200.c | 57 ++++++++++++++
> arch/arm/mach-kirkwood/common.h | 6 ++
> 7 files changed, 181 insertions(+)
> create mode 100644 arch/arm/boot/dts/kirkwood-iomega_ix2_200.dts
> create mode 100644 arch/arm/mach-kirkwood/board-iomega_ix2_200.c
>
> diff --git a/arch/arm/boot/dts/kirkwood-iomega_ix2_200.dts b/arch/arm/boot/dts/kirkwood-iomega_ix2_200.dts
> new file mode 100644
> index 0000000..865aeec
> --- /dev/null
> +++ b/arch/arm/boot/dts/kirkwood-iomega_ix2_200.dts
> @@ -0,0 +1,105 @@
> +/dts-v1/;
> +
> +/include/ "kirkwood.dtsi"
> +
> +/ {
> + model = "Iomega StorCenter ix2-200";
> + compatible = "iom,ix2-200", "marvell,kirkwood-88f6281", "marvell,kirkwood";
> +
> + memory {
> + device_type = "memory";
> + reg = <0x00000000 0x10000000>;
> + };
> +
> + chosen {
> + bootargs = "console=ttyS0,115200n8 earlyprintk";
> + };
> +
> + ocp at f1000000 {
> + i2c at 11000 {
> + status = "okay";
> +
> + lm63: lm63 at 4c {
> + compatible = "national,lm63";
> + reg = <0x4c>;
> + };
> + };
> +
> + serial at 12000 {
> + clock-frequency = <200000000>;
> + status = "ok";
> + };
> +
> + nand at 3000000 {
> + status = "okay";
> +
> + partition at 0 {
> + label = "u-boot";
> + reg = <0x0000000 0x100000>;
> + read-only;
> + };
> +
> + partition at a0000 {
> + label = "env";
> + reg = <0xa0000 0x20000>;
> + read-only;
> + };
> +
> + partition at 100000 {
> + label = "uImage";
> + reg = <0x100000 0x300000>;
> + };
> +
> + partition at 400000 {
> + label = "uInitrd";
> + reg = <0x540000 0x1000000>;
> + };
> + };
> + sata at 80000 {
> + status = "okay";
> + nr-ports = <2>;
> + };
> +
> + };
> + gpio-leds {
> + compatible = "gpio-leds";
> +
> + power_led {
> + label = "status:white:power_led";
> + gpios = <&gpio0 16 0>;
> + linux,default-trigger = "default-on";
> + };
> + health_led1 {
> + label = "status:red:health_led";
> + gpios = <&gpio1 5 0>;
> + };
> + health_led2 {
> + label = "status:white:health_led";
> + gpios = <&gpio1 4 0>;
> + };
> + backup_led {
> + label = "status:blue:backup_led";
> + gpios = <&gpio0 15 0>;
> + };
> + };
> + gpio-keys {
> + compatible = "gpio-keys";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + Power {
> + label = "Power Button";
> + linux,code = <116>;
> + gpios = <&gpio0 14 1>;
> + };
> + Reset {
> + label = "Reset Button";
> + linux,code = <0x198>;
> + gpios = <&gpio0 12 1>;
> + };
> + OTB {
> + label = "OTB Button";
> + linux,code = <133>;
> + gpios = <&gpio1 3 1>;
> + };
> + };
> +};
> diff --git a/arch/arm/mach-kirkwood/Kconfig b/arch/arm/mach-kirkwood/Kconfig
> index ca5c15a..bee8451 100644
> --- a/arch/arm/mach-kirkwood/Kconfig
> +++ b/arch/arm/mach-kirkwood/Kconfig
> @@ -195,6 +195,13 @@ config MACH_T5325
> Say 'Y' here if you want your kernel to support the
> HP t5325 Thin Client.
>
> +config MACH_IOMEGA_IX2_200_DT
> + bool "Iomega StorCenter ix2-200 (Flattened Device Tree)"
> + select ARCH_KIRKWOOD_DT
> + help
> + Say 'Y' here if you want your kernel to support the
> + Iomega StorCenter ix2-200 (Flattened Device Tree).
> +
> endmenu
>
> endif
> diff --git a/arch/arm/mach-kirkwood/Makefile b/arch/arm/mach-kirkwood/Makefile
> index 055c85a..f5484dc 100644
> --- a/arch/arm/mach-kirkwood/Makefile
> +++ b/arch/arm/mach-kirkwood/Makefile
> @@ -28,3 +28,4 @@ obj-$(CONFIG_MACH_IB62X0_DT) += board-ib62x0.o
> obj-$(CONFIG_MACH_TS219_DT) += board-ts219.o tsx1x-common.o
> obj-$(CONFIG_MACH_GOFLEXNET_DT) += board-goflexnet.o
> obj-$(CONFIG_MACH_LSXL_DT) += board-lsxl.o
> +obj-$(CONFIG_MACH_IOMEGA_IX2_200_DT) += board-iomega_ix2_200.o
> diff --git a/arch/arm/mach-kirkwood/Makefile.boot b/arch/arm/mach-kirkwood/Makefile.boot
> index a571755..59b719d 100644
> --- a/arch/arm/mach-kirkwood/Makefile.boot
> +++ b/arch/arm/mach-kirkwood/Makefile.boot
> @@ -11,3 +11,4 @@ dtb-$(CONFIG_MACH_TS219_DT) += kirkwood-qnap-ts219.dtb
> dtb-$(CONFIG_MACH_GOFLEXNET_DT) += kirkwood-goflexnet.dtb
> dtb-$(CONFIG_MACH_LSXL_DT) += kirkwood-lschlv2.dtb
> dtb-$(CONFIG_MACH_LSXL_DT) += kirkwood-lsxhl.dtb
> +dtb-$(CONFIG_MACH_IOMEGA_IX2_200_DT) += kirkwood-iomega_ix2_200.dtb
> diff --git a/arch/arm/mach-kirkwood/board-dt.c b/arch/arm/mach-kirkwood/board-dt.c
> index e4eb450..9b3ec17 100644
> --- a/arch/arm/mach-kirkwood/board-dt.c
> +++ b/arch/arm/mach-kirkwood/board-dt.c
> @@ -87,6 +87,9 @@ static void __init kirkwood_dt_init(void)
> if (of_machine_is_compatible("buffalo,lsxl"))
> lsxl_init();
>
> + if (of_machine_is_compatible("iom,ix2-200"))
> + iomega_ix2_200_init();
> +
> of_platform_populate(NULL, kirkwood_dt_match_table,
> kirkwood_auxdata_lookup, NULL);
> }
> @@ -100,6 +103,7 @@ static const char *kirkwood_dt_board_compat[] = {
> "qnap,ts219",
> "seagate,goflexnet",
> "buffalo,lsxl",
> + "iom,ix2-200",
> NULL
> };
>
> diff --git a/arch/arm/mach-kirkwood/board-iomega_ix2_200.c b/arch/arm/mach-kirkwood/board-iomega_ix2_200.c
> new file mode 100644
> index 0000000..158fb97
> --- /dev/null
> +++ b/arch/arm/mach-kirkwood/board-iomega_ix2_200.c
> @@ -0,0 +1,57 @@
> +/*
> + * arch/arm/mach-kirkwood/board-iomega_ix2_200.c
> + *
> + * Iomega StorCenter ix2-200
> + *
> + * This file is licensed under the terms of the GNU General Public
> + * License version 2. This program is licensed "as is" without any
> + * warranty of any kind, whether express or implied.
> + */
> +
> +#include <linux/kernel.h>
> +#include <linux/init.h>
> +#include <linux/platform_device.h>
> +#include <linux/mv643xx_eth.h>
> +#include <linux/ethtool.h>
> +#include <mach/kirkwood.h>
> +#include "common.h"
> +#include "mpp.h"
> +
> +static struct mv643xx_eth_platform_data iomega_ix2_200_ge00_data = {
> + .phy_addr = MV643XX_ETH_PHY_NONE,
> + .speed = SPEED_1000,
> + .duplex = DUPLEX_FULL,
> +};
> +
> +static unsigned int iomega_ix2_200_mpp_config[] __initdata = {
> + MPP12_GPIO, /* Reset Button */
> + MPP14_GPIO, /* Power Button */
> + MPP15_GPIO, /* Backup LED (blue) */
> + MPP16_GPIO, /* Power LED (white) */
> + MPP35_GPIO, /* OTB Button */
> + MPP36_GPIO, /* Rebuild LED (white) */
> + MPP37_GPIO, /* Health LED (red) */
> + MPP38_GPIO, /* SATA LED brightness control 1 */
> + MPP39_GPIO, /* SATA LED brightness control 2 */
> + MPP40_GPIO, /* Backup LED brightness control 1 */
> + MPP41_GPIO, /* Backup LED brightness control 2 */
> + MPP42_GPIO, /* Power LED brightness control 1 */
> + MPP43_GPIO, /* Power LED brightness control 2 */
> + MPP44_GPIO, /* Health LED brightness control 1 */
> + MPP45_GPIO, /* Health LED brightness control 2 */
> + MPP46_GPIO, /* Rebuild LED brightness control 1 */
> + MPP47_GPIO, /* Rebuild LED brightness control 2 */
> + 0
> +};
> +
> +void __init iomega_ix2_200_init(void)
> +{
> + /*
> + * Basic setup. Needs to be called early.
> + */
> + kirkwood_mpp_conf(iomega_ix2_200_mpp_config);
> +
> + kirkwood_ehci_init();
> +
> + kirkwood_ge01_init(&iomega_ix2_200_ge00_data);
> +}
> diff --git a/arch/arm/mach-kirkwood/common.h b/arch/arm/mach-kirkwood/common.h
> index 304dd1a..d5d4064 100644
> --- a/arch/arm/mach-kirkwood/common.h
> +++ b/arch/arm/mach-kirkwood/common.h
> @@ -94,6 +94,12 @@ void lsxl_init(void);
> static inline void lsxl_init(void) {};
> #endif
>
> +#ifdef CONFIG_MACH_IOMEGA_IX2_200_DT
> +void iomega_ix2_200_init(void);
> +#else
> +static inline void iomega_ix2_200_init(void) {};
> +#endif
> +
> /* early init functions not converted to fdt yet */
> char *kirkwood_id(void);
> void kirkwood_l2_init(void);
> --
> 1.7.9.5
>
Acked-by: Andrew Lunn <andrew at lunn.ch>
Andrew
More information about the linux-arm-kernel
mailing list