[PATCH-V3] ARM: OMAP3+: hwmod: Add AM33XX HWMOD data

[Benoit Cousson]

Hi Guys,

On 08/17/2012 11:58 AM, Tony Lindgren wrote:
> * Hiremath, Vaibhav <hvaibhav at ti.com> [120817 02:51]:
>> On Fri, Aug 17, 2012 at 14:10:47, Tony Lindgren wrote:
>>> * Hiremath, Vaibhav <hvaibhav at ti.com> [120817 01:22]:
>>>> On Fri, Aug 17, 2012 at 13:19:34, Tony Lindgren wrote:
>>>>> * Hiremath, Vaibhav <hvaibhav at ti.com> [120815 02:11]:
>>>>>>
>>>>>> Somehow we have to have some mechanism to initialize " _mpu_rt_va" before 
>>>>>> core_init call, which will take DT resources and initialize accordingly.
>>>>>
>>>>> That's for the device reset/idle? We should not do that in hwmod code
>>>>> except in late_initcall for unclaimed devices as discussed earlier. We
>>>>> discussed setting up the reset function in the device specific headers
>>>>> so both device and hwmod code can call them as needed.
>>>>
>>>> May be I didn't understand your above statement, can you please elaborate 
>>>> more on "device specific header file"?
>>>
>>> We should have the device drivers idle and reset the devices. But also
>>> hwmod may need to do that for the unclaimed devices for PM to work. 
>>> As the driver may not be even compiled in, the driver specific reset and
>>> idle functions should be static inline functions in the device specific
>>> header file so hwmod code can still call those.
>>>  
>>
>> How about mapping the address of the devices?
> 
> That should be done based on the iorange coming from DT during the driver
> probe. The range in hwmod can be populated at that point too if needed.
>  
>> Some more thoughts on the similar line on unclaimed devices -
>> As par of late_initcall(), traverse all the DTB nodes and for each node with 
>> "state = disabled", we can do something like,
>>
>> Late_initcall()
>> 	-> Traverse DTB nodes and check for "state = disabled"
>> 		-> Read the "ti,hwmod" entry and get offsets like, sys_config 
>> 		   and reset.
>> 		-> Map the base address
>> 		-> Enable the module/clock
>> 		-> Reset the device
>> 		-> Write to sysc register offset
>> 		-> Disable the module/clock
>>
>>
>>
>>>> Just to highlight, its not only during late_initcall, the _enable and _idle 
>>>> functions are getting executed as part of every runtime_pm_get\put_sync from 
>>>> the driver.
> 
> Heh, but the unclaimed devices do not have a driver :) So there's no runtime_pm
> calls for the unclaimed devicdes.
> 
>> At the current stage, I really think it would be really nice and beneficial 
>> for driver developers from the community if they get Linux Boot from 
>> linux-next/master branch. I have seen lot of community folks are struggling 
>> with it and they are blocked because we do not have booting kernel on 
>> BeagleBone.
>> They always end up patching kernel with HWMOD patch and submit the driver 
>> patches. So request to consider this cleanup as sequential patch on top of 
>> original HWMOD patch?
> 
> Yes I'm fine merging the data as is, just trying to figure out how to sort
> out the issues for future. 
>  
>>>> May be get rid of resource overwriting for AM33xx and OMAP5 alone as of 
>>>> now??
>>>
>>> Sorry I don't follow this part, care to explain a little more?
>>>
>>
>> As per current implementation, we are using HWMOD information to fill the 
>> platform_device->resources. Even if you pass "reg" and "interrupt" property 
>> from DT, omap_device layer overwrites it with HWMOD data information.
>>
>> So what I am trying to propose here is, avoid this overwrite and resources 
>> (address and interrupt) should strictly gets used from DT blob. Since AM33xx 
>> and OMAP5 devices are the new devices and supports DT boot only, we can 
>> implement it easily for them.
> 
> Yes I agree. And then we should also drop the data from hwmod when it's no
> longer needed.
>  
>> Only issue her is, DMA resources, I was going through some of the old email 
>> archives today, submitted by Benoit and later Jon, but I am still not sure 
>> how to pass dma_channel to driver as a resource.
> 
> Hmm I thought that got merged already?

No, it is still under discussion. I don't even know why they are still
arguing, but there are still a lot of discussion on that thread.

> Anyways, the iorange and interrupts
> are standard resources that should exist in every device entry in .dts files.

Yeah, I wanted to avoid that to make things simpler. As soon as we have
the DMA we can switch easily to DT resource.

My other concern is that so far we still have to duplicate the io space
address with the way the hwmod is initializing the syscofig today.

So it will require some change in that part to make an effective use of
DT. So point is that if we start using that mechanism for DT boot, we
will still have to keep the legacy one for non DT boot.
Nothing is impossible, but that's still a lot of work before having
something useful.

The idea was to stop iterating the hwmods early and init the hwmod only
during device probe or late_initcall for the one that will not probe.

Again, easy with DT, less straighforward for non-DT boot.

Regards,
Benoit