[PATCH 2/2] ARM: da850/omap-l138: Add EVM specific code for VPIF to work
Sekhar Nori
nsekhar at ti.com
Tue Aug 14 09:00:43 EDT 2012
Hi Prabhakar,
On 7/24/2012 1:13 PM, Prabhakar Lad wrote:
> From: Manjunath Hadli <manjunath.hadli at ti.com>
>
> Include the expander settings to select VPIF peripheral on
> UI card and add registration call in EVM init. Also add platform
> data to configure display and capture devices.
>
> Signed-off-by: Manjunath Hadli <manjunath.hadli at ti.com>
> Signed-off-by: Lad, Prabhakar <prabhakar.lad at ti.com>
> Cc: Sekhar Nori <nsekhar at ti.com>
> ---
> arch/arm/mach-davinci/Kconfig | 9 ++
> arch/arm/mach-davinci/board-da850-evm.c | 195 +++++++++++++++++++++++++++++++
> 2 files changed, 204 insertions(+), 0 deletions(-)
>
> diff --git a/arch/arm/mach-davinci/Kconfig b/arch/arm/mach-davinci/Kconfig
> index 32d837d..19ee4ee 100644
> --- a/arch/arm/mach-davinci/Kconfig
> +++ b/arch/arm/mach-davinci/Kconfig
> @@ -190,6 +190,15 @@ config DA850_UI_RMII
> NOTE: Please take care while choosing this option, MII PHY will
> not be functional if RMII mode is selected.
>
> +config DA850_UI_SD_VIDEO_PORT
> + bool "Video Port Interface"
> + help
> + Say Y if you want to use Video Port Interface (VPIF) on the
> + DA850/OMAP-L138 EVM. The Video decoders/encoders are found on the
> + UI daughter card that is supplied with the EVM.
> + NOTE: Please make sure to disable RMII and CLCD options when you
> + select Video Port Interface.
RMII is in the same choice block as this so it is not possible to have
RMII enabled along with video port selection. On the CLCD, it will be
good to register only one of CLCD or video and print a warning if user
enabled both. davinci_evm_init() in
arch/arm/mach-davinci/board-dm644x-evm.c has an example of this.
> +
> endchoice
>
> config DA850_WL12XX
> diff --git a/arch/arm/mach-davinci/board-da850-evm.c b/arch/arm/mach-davinci/board-da850-evm.c
> index 0149fb4..1f5d2c1 100644
> --- a/arch/arm/mach-davinci/board-da850-evm.c
> +++ b/arch/arm/mach-davinci/board-da850-evm.c
> @@ -45,6 +45,8 @@
> #include <mach/aemif.h>
> #include <mach/spi.h>
>
> +#include <media/tvp514x.h>
> +
> #define DA850_EVM_PHY_ID "davinci_mdio-0:00"
> #define DA850_LCD_PWR_PIN GPIO_TO_PIN(2, 8)
> #define DA850_LCD_BL_PIN GPIO_TO_PIN(2, 15)
> @@ -121,6 +123,12 @@ static struct spi_board_info da850evm_spi_info[] = {
> },
> };
>
> +#define TVP5147_CH0 "tvp514x-0"
> +#define TVP5147_CH1 "tvp514x-1"
> +
> +#define VPIF_STATUS 0x002c
> +#define VPIF_STATUS_CLR 0x0030
> +
> #ifdef CONFIG_MTD
> static void da850_evm_m25p80_notify_add(struct mtd_info *mtd)
> {
> @@ -452,6 +460,15 @@ static void da850_evm_ui_keys_init(unsigned gpio)
> }
> }
>
> +#ifdef CONFIG_DA850_UI_SD_VIDEO_PORT
> +static inline void da850_evm_setup_video_port(int video_sel)
> +{
> + gpio_set_value_cansleep(video_sel, 0);
> +}
> +#else
> +static inline void da850_evm_setup_video_port(int video_sel) { }
> +#endif
> +
> static int da850_evm_ui_expander_setup(struct i2c_client *client, unsigned gpio,
> unsigned ngpio, void *c)
> {
> @@ -497,6 +514,8 @@ static int da850_evm_ui_expander_setup(struct i2c_client *client, unsigned gpio,
>
> da850_evm_setup_emac_rmii(sel_a);
>
> + da850_evm_setup_video_port(sel_c);
> +
> return 0;
>
> exp_setup_keys_fail:
> @@ -1149,6 +1168,151 @@ static __init int da850_evm_init_cpufreq(void)
> static __init int da850_evm_init_cpufreq(void) { return 0; }
> #endif
>
> +/* Retaining these APIs, since the VPIF drivers do not check NULL handlers */
> +static int da850_set_vpif_clock(int mux_mode, int hd)
> +{
> + return 0;
> +}
> +
> +static int da850_setup_vpif_input_channel_mode(int mux_mode)
> +{
> + return 0;
> +}
> +
> +int da850_vpif_setup_input_path(int ch, const char *name)
> +{
> + return 0;
> +}
Why not enhance the VPIF driver to handle NULL values for these instead?
> +
> +#if defined(CONFIG_DA850_UI_SD_VIDEO_PORT)
> +/* VPIF capture configuration */
> +static struct tvp514x_platform_data tvp5146_pdata = {
> + .clk_polarity = 0,
> + .hs_polarity = 1,
> + .vs_polarity = 1
> +};
> +#endif
> +
> +#define TVP514X_STD_ALL (V4L2_STD_NTSC | V4L2_STD_PAL)
> +
> +static struct vpif_subdev_info da850_vpif_capture_sdev_info[] = {
> +#if defined(CONFIG_DA850_UI_SD_VIDEO_PORT)
Why not just continue with the previous #ifdef
CONFIG_DA850_UI_SD_VIDEO_PORT?
> + {
> + .name = TVP5147_CH0,
> + .board_info = {
> + I2C_BOARD_INFO("tvp5146", 0x5d),
> + .platform_data = &tvp5146_pdata,
> + },
> + .input = INPUT_CVBS_VI2B,
> + .output = OUTPUT_10BIT_422_EMBEDDED_SYNC,
> + .can_route = 1,
> + .vpif_if = {
> + .if_type = VPIF_IF_BT656,
> + .hd_pol = 1,
> + .vd_pol = 1,
> + .fid_pol = 0,
> + },
> + },
> + {
> + .name = TVP5147_CH1,
> + .board_info = {
> + I2C_BOARD_INFO("tvp5146", 0x5c),
> + .platform_data = &tvp5146_pdata,
> + },
> + .input = INPUT_SVIDEO_VI2C_VI1C,
> + .output = OUTPUT_10BIT_422_EMBEDDED_SYNC,
> + .can_route = 1,
> + .vpif_if = {
> + .if_type = VPIF_IF_BT656,
> + .hd_pol = 1,
> + .vd_pol = 1,
> + .fid_pol = 0,
> + },
> + },
> +#endif
> +};
> +
> +static const struct vpif_input da850_ch0_inputs[] = {
> + {
> + .input = {
> + .index = 0,
> + .name = "Composite",
> + .type = V4L2_INPUT_TYPE_CAMERA,
> + .std = TVP514X_STD_ALL,
> + },
> + .subdev_name = TVP5147_CH0,
> + },
> +};
> +
> +static const struct vpif_input da850_ch1_inputs[] = {
> + {
> + .input = {
> + .index = 0,
> + .name = "S-Video",
> + .type = V4L2_INPUT_TYPE_CAMERA,
> + .std = TVP514X_STD_ALL,
> + },
> + .subdev_name = TVP5147_CH1,
> + },
> +};
> +
> +static struct vpif_capture_config da850_vpif_capture_config = {
> + .setup_input_channel_mode = da850_setup_vpif_input_channel_mode,
> + .setup_input_path = da850_vpif_setup_input_path,
> + .subdev_info = da850_vpif_capture_sdev_info,
> + .subdev_count = ARRAY_SIZE(da850_vpif_capture_sdev_info),
> +#if defined(CONFIG_DA850_UI_SD_VIDEO_PORT)
Same here.
> + .chan_config[0] = {
> + .inputs = da850_ch0_inputs,
> + .input_count = ARRAY_SIZE(da850_ch0_inputs),
> + },
> + .chan_config[1] = {
> + .inputs = da850_ch1_inputs,
> + .input_count = ARRAY_SIZE(da850_ch1_inputs),
> + },
> +#endif
> + .card_name = "DA850/OMAP-L138 Video Capture",
> +};
> +
> +/* VPIF display configuration */
> +static struct vpif_subdev_info da850_vpif_subdev[] = {
> + {
> + .name = "adv7343",
> + .board_info = {
> + I2C_BOARD_INFO("adv7343", 0x2a),
> + },
> + },
> +};
> +
> +static const char const *vpif_output[] = {
> + "Composite",
> + "Component",
> + "S-Video",
> +};
> +
> +static struct vpif_display_config da850_vpif_display_config = {
> + .set_clock = da850_set_vpif_clock,
> + .subdevinfo = da850_vpif_subdev,
> + .subdev_count = ARRAY_SIZE(da850_vpif_subdev),
> + .output = vpif_output,
> + .output_count = ARRAY_SIZE(vpif_output),
> + .card_name = "DA850/OMAP-L138 Video Display",
> +};
> +
> +#if defined(CONFIG_VIDEO_DAVINCI_VPIF_DISPLAY) ||\
> + defined(CONFIG_VIDEO_DAVINCI_VPIF_DISPLAY_MODULE)
> +#define HAS_VPIF_DISPLAY 1
> +#else
> +#define HAS_VPIF_DISPLAY 0
> +#endif
> +
> +#if defined(CONFIG_VIDEO_DAVINCI_VPIF_CAPTURE) ||\
> + defined(CONFIG_VIDEO_DAVINCI_VPIF_CAPTURE_MODULE)
> +#define HAS_VPIF_CAPTURE 1
> +#else
> +#define HAS_VPIF_CAPTURE 0
> +#endif
> +
> #ifdef CONFIG_DA850_WL12XX
>
> static void wl12xx_set_power(int index, bool power_on)
> @@ -1375,6 +1539,37 @@ static __init void da850_evm_init(void)
> pr_warning("da850_evm_init: suspend registration failed: %d\n",
> ret);
>
> + if (HAS_VPIF_DISPLAY || HAS_VPIF_CAPTURE) {
> + ret = da850_register_vpif();
> + if (ret)
> + pr_warn("da850_evm_init: VPIF setup failed: %d\n",
> + ret);
> + }
> +
> + if (HAS_VPIF_CAPTURE) {
> + ret = davinci_cfg_reg_list(da850_vpif_capture_pins);
> + if (ret)
> + pr_warn("da850_evm_init: VPIF capture mux failed:%d\n",
> + ret);
> +
> + ret = da850_register_vpif_capture(&da850_vpif_capture_config);
> + if (ret)
> + pr_warn("da850_evm_init: VPIF capture setup" \
> + " failed: %d\n", ret);
Please don't break print messages.
> + }
> +
> + if (HAS_VPIF_DISPLAY) {
> + ret = davinci_cfg_reg_list(da850_vpif_display_pins);
> + if (ret)
> + pr_warn("da850_evm_init : VPIF capture mux failed" \
> + ": %d\n", ret);
> +
> + ret = da850_register_vpif_display(&da850_vpif_display_config);
> + if (ret)
> + pr_warn("da850_evm_init: VPIF display setup" \
> + " failed: %d\n", ret);
Same here.
Thanks,
Sekhar
More information about the linux-arm-kernel
mailing list