[PATCH v2] Visstrim SM10: Use mo_version to decide board video mode.

[Sascha Hauer]

On Fri, Aug 03, 2012 at 02:08:23PM +0200, Javier Martin wrote:
> If the mother board version number is odd, emmaprp() for
> format conversion + UVC camera will be used.
> 
> Otherwise mx2_camera and m2m-deinterlacer will be registered.
> 
> For both cases Coda video codec is registered.
> 
> Signed-off-by: Javier Martin <javier.martin at vista-silicon.com>

This does not apply. Mainline does not have visstrim_deinterlace_init.

Sascha

> ---
> Changes since v1:
>  - Add error message to emmaprp init function.
> 
> ---
>  arch/arm/mach-imx/mach-imx27_visstrim_m10.c |   54 ++++++++++++++++++++++++---
>  1 file changed, 49 insertions(+), 5 deletions(-)
> 
> diff --git a/arch/arm/mach-imx/mach-imx27_visstrim_m10.c b/arch/arm/mach-imx/mach-imx27_visstrim_m10.c
> index 176533e..dbb344a 100644
> --- a/arch/arm/mach-imx/mach-imx27_visstrim_m10.c
> +++ b/arch/arm/mach-imx/mach-imx27_visstrim_m10.c
> @@ -49,6 +49,10 @@
>  #define OTG_PHY_CS_GPIO (GPIO_PORTF + 17)
>  #define SDHC1_IRQ IRQ_GPIOB(25)
>  
> +#define VERSION_MASK		0x7
> +#define MOTHERBOARD_SHIFT	4
> +#define EXPBOARD_SHIFT		0
> +
>  #define MOTHERBOARD_BIT2	(GPIO_PORTD + 31)
>  #define MOTHERBOARD_BIT1	(GPIO_PORTD + 30)
>  #define MOTHERBOARD_BIT0	(GPIO_PORTD + 29)
> @@ -205,7 +209,7 @@ static struct mx2_camera_platform_data visstrim_camera = {
>  static phys_addr_t mx2_camera_base __initdata;
>  #define MX2_CAMERA_BUF_SIZE SZ_8M
>  
> -static void __init visstrim_camera_init(void)
> +static void __init visstrim_analog_camera_init(void)
>  {
>  	struct platform_device *pdev;
>  	int dma;
> @@ -442,6 +446,29 @@ static void __init visstrim_deinterlace_init(void)
>  		return;
>  }
>  
> +/* Emma-PrP for format conversion */
> +static void __init visstrim_emmaprp_init(void)
> +{
> +	struct platform_device *pdev;
> +	int dma;
> +
> +	pdev = imx27_add_mx2_emmaprp();
> +	if (IS_ERR(pdev))
> +		return;
> +
> +	/*
> +	 * Use the same memory area as the analog camera since both
> +	 * devices are, by nature, exclusive.
> +	 */
> +	dma = dma_declare_coherent_memory(&pdev->dev,
> +				mx2_camera_base, mx2_camera_base,
> +				MX2_CAMERA_BUF_SIZE,
> +				DMA_MEMORY_MAP | DMA_MEMORY_EXCLUSIVE);
> +	if (!(dma & DMA_MEMORY_MAP)) {
> +		pr_err("Failed to declare memory for emmaprp\n");
> +		return;
> +	}
> +}
>  
>  static void __init visstrim_m10_revision(void)
>  {
> @@ -467,13 +494,14 @@ static void __init visstrim_m10_revision(void)
>  	mo_version |= !gpio_get_value(MOTHERBOARD_BIT0);
>  
>  	system_rev = 0x27000;
> -	system_rev |= (mo_version << 4);
> -	system_rev |= exp_version;
> +	system_rev |= (mo_version << MOTHERBOARD_SHIFT);
> +	system_rev |= (exp_version << EXPBOARD_SHIFT);
>  }
>  
>  static void __init visstrim_m10_board_init(void)
>  {
>  	int ret;
> +	int mo_version;
>  
>  	imx27_soc_init();
>  	visstrim_m10_revision();
> @@ -505,8 +533,24 @@ static void __init visstrim_m10_board_init(void)
>  	platform_device_register_resndata(NULL, "soc-camera-pdrv", 0, NULL, 0,
>  				      &iclink_tvp5150, sizeof(iclink_tvp5150));
>  	gpio_led_register_device(0, &visstrim_m10_led_data);
> -	visstrim_deinterlace_init();
> -	visstrim_camera_init();
> +
> +	/* Use mother board version to decide what video devices we shall use */
> +	mo_version = (system_rev >> MOTHERBOARD_SHIFT) & VERSION_MASK;
> +	if (mo_version & 0x1) {
> +		visstrim_emmaprp_init();
> +
> +		/*
> +		 * Despite not being used, tvp5150 must be
> +		 * powered on to avoid I2C problems. To minimize
> +		 * power consupmtion keep reset enabled.
> +		 */
> +		gpio_set_value(TVP5150_PWDN, 1);
> +		ndelay(1);
> +		gpio_set_value(TVP5150_RSTN, 0);
> +	} else {
> +		visstrim_deinterlace_init();
> +		visstrim_analog_camera_init();
> +	}
>  	visstrim_coda_init();
>  }
>  
> -- 
> 1.7.9.5
> 
> 

-- 
Pengutronix e.K.                           |                             |
Industrial Linux Solutions                 | http://www.pengutronix.de/  |
Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0    |
Amtsgericht Hildesheim, HRA 2686           | Fax:   +49-5121-206917-5555 |