[PATCH] spi/imx: Fix spi-imx when the hardware SPI chipselects are used
Uwe Kleine-König
u.kleine-koenig at pengutronix.de
Thu Sep 15 14:17:07 EDT 2011
On Thu, Sep 15, 2011 at 01:16:46PM -0300, Fabio Estevam wrote:
> commit 22a85e4cd51 (spi/imx: add device tree probe support) broke spi-imx usage
> when the SPI chipselect is the one internal to the controller.
>
> On a mx31pdk board the following error is seen:
>
> Registering mxc_nand as whole device
> ------------[ cut here ]------------
> WARNING: at drivers/gpio/gpiolib.c:101 gpio_ensure_requested+0x4c/0xf4()
> autorequest GPIO-0
> Modules linked in:
> [<c0014410>] (unwind_backtrace+0x0/0xf4) from [<c0025754>] (warn_slowpath_common+0x4c/0x64)
> [<c0025754>] (warn_slowpath_common+0x4c/0x64) from [<c0025800>] (warn_slowpath_fmt+0x30/0x40)
> [<c0025800>] (warn_slowpath_fmt+0x30/0x40) from [<c0198688>] (gpio_ensure_requested+0x4c/0xf4)
> [<c0198688>] (gpio_ensure_requested+0x4c/0xf4) from [<c01988c8>] (gpio_direction_output+0xa0/0x138)
> [<c01988c8>] (gpio_direction_output+0xa0/0x138) from [<c01ed198>] (spi_imx_setup+0x38/0x4c)
> [<c01ed198>] (spi_imx_setup+0x38/0x4c) from [<c01eb5d0>] (spi_setup+0x38/0x50)
> [<c01eb5d0>] (spi_setup+0x38/0x50) from [<c01eb85c>] (spi_add_device+0x94/0x124)
> [<c01eb85c>] (spi_add_device+0x94/0x124) from [<c01eb960>] (spi_new_device+0x74/0xac)
> [<c01eb960>] (spi_new_device+0x74/0xac) from [<c01eb9b8>] (spi_match_master_to_boardinfo+0x20/0x40)
> [<c01eb9b8>] (spi_match_master_to_boardinfo+0x20/0x40) from [<c01eba88>] (spi_register_master+0xb0/0x104)
> [<c01eba88>] (spi_register_master+0xb0/0x104) from [<c01ec0b4>] (spi_bitbang_start+0x104/0x17c)
> [<c01ec0b4>] (spi_bitbang_start+0x104/0x17c) from [<c02c2c4c>] (spi_imx_probe+0x2fc/0x404)
> [<c02c2c4c>] (spi_imx_probe+0x2fc/0x404) from [<c01c2498>] (platform_drv_probe+0x18/0x1c)
> [<c01c2498>] (platform_drv_probe+0x18/0x1c) from [<c01c1058>] (driver_probe_device+0x78/0x174)
> [<c01c1058>] (driver_probe_device+0x78/0x174) from [<c01c11e0>] (__driver_attach+0x8c/0x90)
> [<c01c11e0>] (__driver_attach+0x8c/0x90) from [<c01c0860>] (bus_for_each_dev+0x60/0x8c)
> [<c01c0860>] (bus_for_each_dev+0x60/0x8c) from [<c01c0088>] (bus_add_driver+0xa0/0x288)
> [<c01c0088>] (bus_add_driver+0xa0/0x288) from [<c01c179c>] (driver_register+0x78/0x18c)
> [<c01c179c>] (driver_register+0x78/0x18c) from [<c0008490>] (do_one_initcall+0x34/0x178)
> [<c0008490>] (do_one_initcall+0x34/0x178) from [<c03a5204>] (kernel_init+0x74/0x118)
> [<c03a5204>] (kernel_init+0x74/0x118) from [<c000f65c>] (kernel_thread_exit+0x0/0x8)
> ---[ end trace 759f924b30fd5a44 ]---
>
> Fix this issue by using the original chip select logic and make spi-imx to work again.
>
> Tested on a mx31pdk that uses the hardware SPI chipselect pins and also
> on a mx27pdk that uses GPIO as SPI chipselect.
>
> Signed-off-by: Fabio Estevam <fabio.estevam at freescale.com>
> ---
> drivers/spi/spi-imx.c | 8 +++-----
> 1 files changed, 3 insertions(+), 5 deletions(-)
>
> diff --git a/drivers/spi/spi-imx.c b/drivers/spi/spi-imx.c
> index 8ac6542..7821c48 100644
> --- a/drivers/spi/spi-imx.c
> +++ b/drivers/spi/spi-imx.c
> @@ -783,12 +783,10 @@ static int __devinit spi_imx_probe(struct platform_device *pdev)
> spi_imx->bitbang.master = spi_master_get(master);
>
> for (i = 0; i < master->num_chipselect; i++) {
> - int cs_gpio = of_get_named_gpio(np, "cs-gpios", i);
> - if (cs_gpio < 0)
> - cs_gpio = mxc_platform_info->chipselect[i];
> - if (cs_gpio < 0)
> + spi_imx->chipselect[i] = mxc_platform_info->chipselect[i];
> + if (spi_imx->chipselect[i] < 0)
> continue;
> - spi_imx->chipselect[i] = cs_gpio;
> +
> ret = gpio_request(spi_imx->chipselect[i], DRIVER_NAME);
> if (ret) {
> while (i > 0) {
I think this is wrong. My first guess is you need to move
spi_imx->chipselect[i] = cs_gpio;
before
if (cs_gpio < 0)
continue;
Does that make sense and works?
Uwe
--
Pengutronix e.K. | Uwe Kleine-König |
Industrial Linux Solutions | http://www.pengutronix.de/ |
More information about the linux-arm-kernel
mailing list