[PATCH] dmaengine: add CSR SiRFprimaII DMAC driver
Barry Song
21cnbao at gmail.com
Wed Sep 14 02:46:12 EDT 2011
Hi Jassi,
2011/9/8 Jassi Brar <jassisinghbrar at gmail.com>:
> On Thu, Sep 8, 2011 at 8:47 AM, Jassi Brar <jassisinghbrar at gmail.com> wrote:
>> On Thu, Sep 8, 2011 at 7:42 AM, Barry Song <21cnbao at gmail.com> wrote:
>>
>>>>> it is much different with primacell based DMA like pl080, pl330.
>>>>> prima2 has a self-defined DMAC IP. basically it is a 2D mode dma with
>>>>> two scales X and Y and direct way to start and stop DMA.
>>>>> every channel has fixed function to serve only one perpheral. so you
>>>>> find we have a filter id.
>>>> okay, what do you mean by 2D mode? Is it similar to what TI folks, Linus
>>>> W and Jassi Brar posted RFC's on?
>>>
>>> In SiRFprimaII 2-D DMA, the system memory space is interpreted
>>> as a 2-D layout instead of a linear 1-D layout. More specifically, the
>>> system memory can be considered as
>>> multiple data lines. The length of the data line is determined by the
>>> user-selected DMA_WIDTH register.
>>> The user can specify a data window that the user wants to access using
>>> four parameters:
>>> ■ Start address
>>> ■ X length
>>> ■ Y length
>>> ■ Width
>>>
>>> The idea of a 2-D DMA is shown in figure 2d-dma.png attached.
>>>
>>> If you specifies the Y length as 0 or the X length equals to the DMA
>>> width, then this 2-D DMA reduces to
>>> 1-D. If the user configures the X length greater than the DMA width,
>>> then the extra data is wrapped around
>>> to the next data line, this may corrupt the DMA transfer for
>>> multiple-line 2-D DMA. If this is a 1-D DMA, then
>>> there is no issue. The attached diagram 2d-dma2.png shows the
>>> wrap-around of the extra data in case the X length
>>> greater than DMA width.
>>
>> Sorry, the role of DMA_WIDTH is not clear to me yet.
>> In which case the user _must_ set {xlen > width} ?
>>
> Perhaps 2d-dma.PNG is inaccurate - it shouldn't depict any deltaX.
> Doesn't xlen and width always start together ? If no, please don't read ahead.
>
> According to figures, {xlen > width} is to be set _only_ when a transfer
> is divided into _exactly_ two chunks separated by gap _exactly_
> equal to length of the second chunk (an extremely rare case).
>
> Anyways, every case can be easily expressed using the generic api
> I proposed. See 'struct xfer_template' in https://lkml.org/lkml/2011/8/12/128
>
> Roughly speaking, the following should be done...
> Client driver :-
> **************
> For a 'Rectangular' transfer (2d-dma.PNG) :-
> xfer_template.numf = Ylen; /* height of rectangle */
> xfer_template.frame_size = 1;
> xfer_template.sgl[0].size = Xlen; /* width of rectangle */
> xfer_template.sgl[0].icg = start_addr_Y(n) - end_addr_Y(n-1);
For prima2:
xfer_template.numf = ylen + 1
xfer_template.frame_size = 1;
xfer_template.sgl[0].size = xlen;
xfer_template.sgl[0].icg = dma_width - xlen;
>
> For the "A Line and some" transfer (2d-dma2.PNG) :-
> xfer_template.numf = 1;
> xfer_template.frame_size = 2;
> xfer_template.sgl[0].size = xlen1; /* a line */
> xfer_template.sgl[1].size = xlen2; /* and some */
> xfer_template.sgl[0].icg = start_addr_Y(n) - end_addr_Y(n-1);
> xfer_template.sgl[1].icg = 0; /* doesn't matter */
>
> DMAC driver :-
> ***************
> if (xfer_template.frame_size == 1) {
> /* rectangle */
> schan->xlen = xfer_template.sgl[0].size;
> schan->width = schan->xlen + xfer_template.sgl[0].icg;
> } else if (xfer_template.frame_size == 2 &&
> xfer_template.numf == 1 &&
> xfer_template.sgl[1].size == xfer_template.sgl[0].icg){
> /* a line and some */
> schan->xlen = xfer_template.sgl[0].size + xfer_template.sgl[1].size.
> schan->width = xfer_template.sgl[0].size;
> } else {
> /* _Hardware_ doesn't support the transfer as such. *
> return -EINVAL;
> }
> schan->ylen = xfer_template.numf /* -1? */;
>
For prima2:
xfer_template.frame_size is always 1, then
schan->xlen = xfer_template.sgl[0].size;
schan->width = schan->xlen + xfer_template.sgl[0].icg;
Thanks
barry
More information about the linux-arm-kernel
mailing list