[PATCH 2/5] ARM: SAMSUNG: Make the sleep code common for S3C64XX and newer SoCs

[Kukjin Kim]

Abhilash Kesavan wrote:
> 
> Hi Mr Kim,
> 
> Thanks for your comments. Please find my reply below:
> 
> Regards,
> Abhilash
> 
> On Fri, Aug 26, 2011 at 7:10 AM, Kukjin Kim <kgene.kim at samsung.com> wrote:
> > Abhilash Kesavan wrote:
> >>
> >> The sleep code for S5PV210 and EXYNOS4 is identical; moreover it is
quite
> >> similar
> >> to that for S3C64XX except for some SoC specific debug logic. S5P64X0
and
> >> S5PC100,
> >> for which support will be added soon, can also use the same procedure.
> > Create a
> >> common sleep code in the plat-samsung directory so that it can be
re-used.
> >>
> >> Signed-off-by: Abhilash Kesavan <a.kesavan at samsung.com>
> >> ---
> >>  arch/arm/mach-exynos4/Kconfig  |    1 +
> >>  arch/arm/mach-exynos4/Makefile |    2 +-
> >>  arch/arm/mach-exynos4/sleep.S  |   54 ---------------------------
> >>  arch/arm/mach-s3c64xx/Kconfig  |    1 +
> >>  arch/arm/mach-s3c64xx/Makefile |    1 -
> >>  arch/arm/mach-s3c64xx/sleep.S  |   72
> > ------------------------------------
> >>  arch/arm/mach-s5pv210/Kconfig  |    1 +
> >>  arch/arm/mach-s5pv210/Makefile |    2 +-
> >>  arch/arm/mach-s5pv210/sleep.S  |   52 --------------------------
> >>  arch/arm/plat-samsung/Kconfig  |    7 +++
> >>  arch/arm/plat-samsung/Makefile |    1 +
> >>  arch/arm/plat-samsung/sleep.S  |   80
> >> ++++++++++++++++++++++++++++++++++++++++
> >>  12 files changed, 93 insertions(+), 181 deletions(-)
> >>  delete mode 100644 arch/arm/mach-exynos4/sleep.S
> >>  delete mode 100644 arch/arm/mach-s3c64xx/sleep.S
> >>  delete mode 100644 arch/arm/mach-s5pv210/sleep.S
> >>  create mode 100644 arch/arm/plat-samsung/sleep.S
> >>
> >
> > (snip)
> >
> >> +ENTRY(s3c_cpu_resume)
> >> +#if defined(CONFIG_S3C_PM_DEBUG_LED_SMDK)
> >> +
> >
> > Hi Abhilash,
> >
> > Yes, would be nice if each sleep.S can be handled in plat-samsung for
> > Samsung SoCs.
> >
> > Hmm...but the CONFIG_S3C_PM_DEBUG_LED_SMDK can be used on other
> SoCs for
> > same reason even though it is available only on S3C64XX now. I think, we
> > need to add SoC detecting here.
> Quite right, it is possible to use this for other SoCs. But as of now,
> my patch just intends
> to move all the sleep code to a common place. The S3C64XX sleep code
> has this feature
> and I didn't want to disturb it in anyway, hence it has been added to
> the common file.
> Perhaps, generalizing it for other SoCs can be done later on top of this

Hmm, this codes should be cleaned for all Samsung SoCs because this can
break one kernel image...

> >
> >> +#undef S3C64XX_VA_GPIO
> >> +#define S3C64XX_VA_GPIO (0x0)
> >
> > Please let me know why this is needed here.
> The code is trying to access the registers at a stage where the MMU is
> not enabled.
> Hence, the VA_GPIO is being re-defined as 0 reducing S3C64XX_GPIOREG(reg)
> to
> reg.
> It has been moved as is from the existing s3c64xx sleep code.


Thanks.

Best regards,
Kgene.
--
Kukjin Kim <kgene.kim at samsung.com>, Senior Engineer,
SW Solution Development Team, Samsung Electronics Co., Ltd.