[PATCH 1/3] ARM: msm: Remove MSM7x00 support
David Brown
davidb at codeaurora.org
Wed Nov 30 19:29:02 EST 2011
This target has been bitrotting for a while. The hardware is quite a
bit different from the other MSM targets, making it hard to justify
maintaining the support in the kernel. This SoC was dropped from
Google's Android kernel a while back.
Signed-off-by: David Brown <davidb at codeaurora.org>
---
arch/arm/mach-msm/Kconfig | 29 +--
arch/arm/mach-msm/Makefile | 4 -
arch/arm/mach-msm/acpuclock-arm11.c | 525 -----------------------
arch/arm/mach-msm/acpuclock.h | 32 --
arch/arm/mach-msm/board-halibut.c | 102 -----
arch/arm/mach-msm/board-trout-gpio.c | 233 ----------
arch/arm/mach-msm/board-trout-mmc.c | 185 --------
arch/arm/mach-msm/board-trout-panel.c | 296 -------------
arch/arm/mach-msm/board-trout.c | 102 -----
arch/arm/mach-msm/board-trout.h | 162 -------
arch/arm/mach-msm/idle.S | 13 -
arch/arm/mach-msm/include/mach/irqs-7x00.h | 75 ----
arch/arm/mach-msm/include/mach/irqs.h | 2 -
arch/arm/mach-msm/include/mach/msm_iomap-7x00.h | 127 ------
arch/arm/mach-msm/include/mach/msm_iomap.h | 2 -
arch/arm/mach-msm/io.c | 34 --
arch/arm/mach-msm/irq.c | 151 -------
arch/arm/mach-msm/smd_private.h | 39 --
arch/arm/mach-msm/timer.c | 5 +-
19 files changed, 2 insertions(+), 2116 deletions(-)
delete mode 100644 arch/arm/mach-msm/acpuclock-arm11.c
delete mode 100644 arch/arm/mach-msm/acpuclock.h
delete mode 100644 arch/arm/mach-msm/board-halibut.c
delete mode 100644 arch/arm/mach-msm/board-trout-gpio.c
delete mode 100644 arch/arm/mach-msm/board-trout-mmc.c
delete mode 100644 arch/arm/mach-msm/board-trout-panel.c
delete mode 100644 arch/arm/mach-msm/board-trout.c
delete mode 100644 arch/arm/mach-msm/board-trout.h
delete mode 100644 arch/arm/mach-msm/include/mach/irqs-7x00.h
delete mode 100644 arch/arm/mach-msm/include/mach/msm_iomap-7x00.h
delete mode 100644 arch/arm/mach-msm/irq.c
diff --git a/arch/arm/mach-msm/Kconfig b/arch/arm/mach-msm/Kconfig
index ebde97f..643a706 100644
--- a/arch/arm/mach-msm/Kconfig
+++ b/arch/arm/mach-msm/Kconfig
@@ -2,18 +2,7 @@ if ARCH_MSM
choice
prompt "Qualcomm MSM SoC Type"
- default ARCH_MSM7X00A
-
-config ARCH_MSM7X00A
- bool "MSM7x00A / MSM7x01A"
- select MACH_TROUT if !MACH_HALIBUT
- select ARCH_MSM_ARM11
- select MSM_SMD
- select MSM_SMD_PKG3
- select CPU_V6
- select GPIO_MSM_V1
- select MSM_PROC_COMM
- select HAS_MSM_DEBUG_UART_PHYS
+ default ARCH_QSD8X50
config ARCH_MSM7X30
bool "MSM7x30"
@@ -68,8 +57,6 @@ config MSM_SOC_REV_A
config ARCH_MSM_SCORPIONMP
bool
-config ARCH_MSM_ARM11
- bool
config ARCH_MSM_SCORPION
bool
@@ -81,20 +68,6 @@ config MSM_VIC
menu "Qualcomm MSM Board Type"
-config MACH_HALIBUT
- depends on ARCH_MSM
- depends on ARCH_MSM7X00A
- bool "Halibut Board (QCT SURF7201A)"
- help
- Support for the Qualcomm SURF7201A eval board.
-
-config MACH_TROUT
- depends on ARCH_MSM
- depends on ARCH_MSM7X00A
- bool "HTC Dream (aka trout)"
- help
- Support for the HTC Dream, T-Mobile G1, Android ADP1 devices.
-
config MACH_MSM7X30_SURF
depends on ARCH_MSM7X30
bool "MSM7x30 SURF"
diff --git a/arch/arm/mach-msm/Makefile b/arch/arm/mach-msm/Makefile
index 4ad3969..4a5dfb8 100644
--- a/arch/arm/mach-msm/Makefile
+++ b/arch/arm/mach-msm/Makefile
@@ -5,7 +5,6 @@ obj-$(CONFIG_DEBUG_FS) += clock-debug.o
obj-$(CONFIG_MSM_VIC) += irq-vic.o
obj-$(CONFIG_MSM_IOMMU) += devices-iommu.o
-obj-$(CONFIG_ARCH_MSM7X00A) += dma.o irq.o acpuclock-arm11.o
obj-$(CONFIG_ARCH_MSM7X30) += dma.o
obj-$(CONFIG_ARCH_QSD8X50) += dma.o sirc.o
@@ -20,9 +19,6 @@ CFLAGS_scm.o :=$(call as-instr,.arch_extension sec,-DREQUIRES_SEC=1)
obj-$(CONFIG_HOTPLUG_CPU) += hotplug.o
obj-$(CONFIG_SMP) += headsmp.o platsmp.o
-obj-$(CONFIG_MACH_TROUT) += board-trout.o board-trout-gpio.o board-trout-mmc.o devices-msm7x00.o
-obj-$(CONFIG_MACH_TROUT) += board-trout.o board-trout-gpio.o board-trout-mmc.o board-trout-panel.o devices-msm7x00.o
-obj-$(CONFIG_MACH_HALIBUT) += board-halibut.o devices-msm7x00.o
obj-$(CONFIG_ARCH_MSM7X30) += board-msm7x30.o devices-msm7x30.o
obj-$(CONFIG_ARCH_QSD8X50) += board-qsd8x50.o devices-qsd8x50.o
obj-$(CONFIG_ARCH_MSM8X60) += board-msm8x60.o
diff --git a/arch/arm/mach-msm/acpuclock-arm11.c b/arch/arm/mach-msm/acpuclock-arm11.c
deleted file mode 100644
index 805d4ee..0000000
--- a/arch/arm/mach-msm/acpuclock-arm11.c
+++ /dev/null
@@ -1,525 +0,0 @@
-/* arch/arm/mach-msm/acpuclock.c
- *
- * MSM architecture clock driver
- *
- * Copyright (C) 2007 Google, Inc.
- * Copyright (c) 2007 QUALCOMM Incorporated
- * Author: San Mehat <san at android.com>
- *
- * This software is licensed under the terms of the GNU General Public
- * License version 2, as published by the Free Software Foundation, and
- * may be copied, distributed, and modified under those terms.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/list.h>
-#include <linux/errno.h>
-#include <linux/string.h>
-#include <linux/delay.h>
-#include <linux/clk.h>
-#include <linux/cpufreq.h>
-#include <linux/mutex.h>
-#include <linux/io.h>
-#include <mach/board.h>
-#include <mach/msm_iomap.h>
-
-#include "proc_comm.h"
-#include "acpuclock.h"
-
-
-#define A11S_CLK_CNTL_ADDR (MSM_CSR_BASE + 0x100)
-#define A11S_CLK_SEL_ADDR (MSM_CSR_BASE + 0x104)
-#define A11S_VDD_SVS_PLEVEL_ADDR (MSM_CSR_BASE + 0x124)
-
-/*
- * ARM11 clock configuration for specific ACPU speeds
- */
-
-#define ACPU_PLL_TCXO -1
-#define ACPU_PLL_0 0
-#define ACPU_PLL_1 1
-#define ACPU_PLL_2 2
-#define ACPU_PLL_3 3
-
-#define PERF_SWITCH_DEBUG 0
-#define PERF_SWITCH_STEP_DEBUG 0
-
-struct clock_state
-{
- struct clkctl_acpu_speed *current_speed;
- struct mutex lock;
- uint32_t acpu_switch_time_us;
- uint32_t max_speed_delta_khz;
- uint32_t vdd_switch_time_us;
- unsigned long power_collapse_khz;
- unsigned long wait_for_irq_khz;
-};
-
-static struct clk *ebi1_clk;
-static struct clock_state drv_state = { 0 };
-
-static void __init acpuclk_init(void);
-
-/* MSM7201A Levels 3-6 all correspond to 1.2V, level 7 corresponds to 1.325V. */
-enum {
- VDD_0 = 0,
- VDD_1 = 1,
- VDD_2 = 2,
- VDD_3 = 3,
- VDD_4 = 3,
- VDD_5 = 3,
- VDD_6 = 3,
- VDD_7 = 7,
- VDD_END
-};
-
-struct clkctl_acpu_speed {
- unsigned int a11clk_khz;
- int pll;
- unsigned int a11clk_src_sel;
- unsigned int a11clk_src_div;
- unsigned int ahbclk_khz;
- unsigned int ahbclk_div;
- int vdd;
- unsigned int axiclk_khz;
- unsigned long lpj; /* loops_per_jiffy */
-/* Index in acpu_freq_tbl[] for steppings. */
- short down;
- short up;
-};
-
-/*
- * ACPU speed table. Complete table is shown but certain speeds are commented
- * out to optimized speed switching. Initialize loops_per_jiffy to 0.
- *
- * Table stepping up/down is optimized for 256mhz jumps while staying on the
- * same PLL.
- */
-#if (0)
-static struct clkctl_acpu_speed acpu_freq_tbl[] = {
- { 19200, ACPU_PLL_TCXO, 0, 0, 19200, 0, VDD_0, 30720, 0, 0, 8 },
- { 61440, ACPU_PLL_0, 4, 3, 61440, 0, VDD_0, 30720, 0, 0, 8 },
- { 81920, ACPU_PLL_0, 4, 2, 40960, 1, VDD_0, 61440, 0, 0, 8 },
- { 96000, ACPU_PLL_1, 1, 7, 48000, 1, VDD_0, 61440, 0, 0, 9 },
- { 122880, ACPU_PLL_0, 4, 1, 61440, 1, VDD_3, 61440, 0, 0, 8 },
- { 128000, ACPU_PLL_1, 1, 5, 64000, 1, VDD_3, 61440, 0, 0, 12 },
- { 176000, ACPU_PLL_2, 2, 5, 88000, 1, VDD_3, 61440, 0, 0, 11 },
- { 192000, ACPU_PLL_1, 1, 3, 64000, 2, VDD_3, 61440, 0, 0, 12 },
- { 245760, ACPU_PLL_0, 4, 0, 81920, 2, VDD_4, 61440, 0, 0, 12 },
- { 256000, ACPU_PLL_1, 1, 2, 128000, 2, VDD_5, 128000, 0, 0, 12 },
- { 264000, ACPU_PLL_2, 2, 3, 88000, 2, VDD_5, 128000, 0, 6, 13 },
- { 352000, ACPU_PLL_2, 2, 2, 88000, 3, VDD_5, 128000, 0, 6, 13 },
- { 384000, ACPU_PLL_1, 1, 1, 128000, 2, VDD_6, 128000, 0, 5, -1 },
- { 528000, ACPU_PLL_2, 2, 1, 132000, 3, VDD_7, 128000, 0, 11, -1 },
- { 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 },
-};
-#else /* Table of freq we currently use. */
-static struct clkctl_acpu_speed acpu_freq_tbl[] = {
- { 19200, ACPU_PLL_TCXO, 0, 0, 19200, 0, VDD_0, 30720, 0, 0, 4 },
- { 122880, ACPU_PLL_0, 4, 1, 61440, 1, VDD_3, 61440, 0, 0, 4 },
- { 128000, ACPU_PLL_1, 1, 5, 64000, 1, VDD_3, 61440, 0, 0, 6 },
- { 176000, ACPU_PLL_2, 2, 5, 88000, 1, VDD_3, 61440, 0, 0, 5 },
- { 245760, ACPU_PLL_0, 4, 0, 81920, 2, VDD_4, 61440, 0, 0, 5 },
- { 352000, ACPU_PLL_2, 2, 2, 88000, 3, VDD_5, 128000, 0, 3, 7 },
- { 384000, ACPU_PLL_1, 1, 1, 128000, 2, VDD_6, 128000, 0, 2, -1 },
- { 528000, ACPU_PLL_2, 2, 1, 132000, 3, VDD_7, 128000, 0, 5, -1 },
- { 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 },
-};
-#endif
-
-
-#ifdef CONFIG_CPU_FREQ_TABLE
-static struct cpufreq_frequency_table freq_table[] = {
- { 0, 122880 },
- { 1, 128000 },
- { 2, 245760 },
- { 3, 384000 },
- { 4, 528000 },
- { 5, CPUFREQ_TABLE_END },
-};
-#endif
-
-static int pc_pll_request(unsigned id, unsigned on)
-{
- int res;
- on = !!on;
-
-#if PERF_SWITCH_DEBUG
- if (on)
- printk(KERN_DEBUG "Enabling PLL %d\n", id);
- else
- printk(KERN_DEBUG "Disabling PLL %d\n", id);
-#endif
-
- res = msm_proc_comm(PCOM_CLKCTL_RPC_PLL_REQUEST, &id, &on);
- if (res < 0)
- return res;
-
-#if PERF_SWITCH_DEBUG
- if (on)
- printk(KERN_DEBUG "PLL %d enabled\n", id);
- else
- printk(KERN_DEBUG "PLL %d disabled\n", id);
-#endif
- return res;
-}
-
-
-/*----------------------------------------------------------------------------
- * ARM11 'owned' clock control
- *---------------------------------------------------------------------------*/
-
-unsigned long acpuclk_power_collapse(void) {
- int ret = acpuclk_get_rate();
- ret *= 1000;
- if (ret > drv_state.power_collapse_khz)
- acpuclk_set_rate(drv_state.power_collapse_khz, 1);
- return ret;
-}
-
-unsigned long acpuclk_get_wfi_rate(void)
-{
- return drv_state.wait_for_irq_khz;
-}
-
-unsigned long acpuclk_wait_for_irq(void) {
- int ret = acpuclk_get_rate();
- ret *= 1000;
- if (ret > drv_state.wait_for_irq_khz)
- acpuclk_set_rate(drv_state.wait_for_irq_khz, 1);
- return ret;
-}
-
-static int acpuclk_set_vdd_level(int vdd)
-{
- uint32_t current_vdd;
-
- current_vdd = readl(A11S_VDD_SVS_PLEVEL_ADDR) & 0x07;
-
-#if PERF_SWITCH_DEBUG
- printk(KERN_DEBUG "acpuclock: Switching VDD from %u -> %d\n",
- current_vdd, vdd);
-#endif
- writel((1 << 7) | (vdd << 3), A11S_VDD_SVS_PLEVEL_ADDR);
- udelay(drv_state.vdd_switch_time_us);
- if ((readl(A11S_VDD_SVS_PLEVEL_ADDR) & 0x7) != vdd) {
-#if PERF_SWITCH_DEBUG
- printk(KERN_ERR "acpuclock: VDD set failed\n");
-#endif
- return -EIO;
- }
-
-#if PERF_SWITCH_DEBUG
- printk(KERN_DEBUG "acpuclock: VDD switched\n");
-#endif
- return 0;
-}
-
-/* Set proper dividers for the given clock speed. */
-static void acpuclk_set_div(const struct clkctl_acpu_speed *hunt_s) {
- uint32_t reg_clkctl, reg_clksel, clk_div;
-
- /* AHB_CLK_DIV */
- clk_div = (readl(A11S_CLK_SEL_ADDR) >> 1) & 0x03;
- /*
- * If the new clock divider is higher than the previous, then
- * program the divider before switching the clock
- */
- if (hunt_s->ahbclk_div > clk_div) {
- reg_clksel = readl(A11S_CLK_SEL_ADDR);
- reg_clksel &= ~(0x3 << 1);
- reg_clksel |= (hunt_s->ahbclk_div << 1);
- writel(reg_clksel, A11S_CLK_SEL_ADDR);
- }
- if ((readl(A11S_CLK_SEL_ADDR) & 0x01) == 0) {
- /* SRC0 */
-
- /* Program clock source */
- reg_clkctl = readl(A11S_CLK_CNTL_ADDR);
- reg_clkctl &= ~(0x07 << 4);
- reg_clkctl |= (hunt_s->a11clk_src_sel << 4);
- writel(reg_clkctl, A11S_CLK_CNTL_ADDR);
-
- /* Program clock divider */
- reg_clkctl = readl(A11S_CLK_CNTL_ADDR);
- reg_clkctl &= ~0xf;
- reg_clkctl |= hunt_s->a11clk_src_div;
- writel(reg_clkctl, A11S_CLK_CNTL_ADDR);
-
- /* Program clock source selection */
- reg_clksel = readl(A11S_CLK_SEL_ADDR);
- reg_clksel |= 1; /* CLK_SEL_SRC1NO == SRC1 */
- writel(reg_clksel, A11S_CLK_SEL_ADDR);
- } else {
- /* SRC1 */
-
- /* Program clock source */
- reg_clkctl = readl(A11S_CLK_CNTL_ADDR);
- reg_clkctl &= ~(0x07 << 12);
- reg_clkctl |= (hunt_s->a11clk_src_sel << 12);
- writel(reg_clkctl, A11S_CLK_CNTL_ADDR);
-
- /* Program clock divider */
- reg_clkctl = readl(A11S_CLK_CNTL_ADDR);
- reg_clkctl &= ~(0xf << 8);
- reg_clkctl |= (hunt_s->a11clk_src_div << 8);
- writel(reg_clkctl, A11S_CLK_CNTL_ADDR);
-
- /* Program clock source selection */
- reg_clksel = readl(A11S_CLK_SEL_ADDR);
- reg_clksel &= ~1; /* CLK_SEL_SRC1NO == SRC0 */
- writel(reg_clksel, A11S_CLK_SEL_ADDR);
- }
-
- /*
- * If the new clock divider is lower than the previous, then
- * program the divider after switching the clock
- */
- if (hunt_s->ahbclk_div < clk_div) {
- reg_clksel = readl(A11S_CLK_SEL_ADDR);
- reg_clksel &= ~(0x3 << 1);
- reg_clksel |= (hunt_s->ahbclk_div << 1);
- writel(reg_clksel, A11S_CLK_SEL_ADDR);
- }
-}
-
-int acpuclk_set_rate(unsigned long rate, int for_power_collapse)
-{
- uint32_t reg_clkctl;
- struct clkctl_acpu_speed *cur_s, *tgt_s, *strt_s;
- int rc = 0;
- unsigned int plls_enabled = 0, pll;
-
- strt_s = cur_s = drv_state.current_speed;
-
- WARN_ONCE(cur_s == NULL, "acpuclk_set_rate: not initialized\n");
- if (cur_s == NULL)
- return -ENOENT;
-
- if (rate == (cur_s->a11clk_khz * 1000))
- return 0;
-
- for (tgt_s = acpu_freq_tbl; tgt_s->a11clk_khz != 0; tgt_s++) {
- if (tgt_s->a11clk_khz == (rate / 1000))
- break;
- }
-
- if (tgt_s->a11clk_khz == 0)
- return -EINVAL;
-
- /* Choose the highest speed speed at or below 'rate' with same PLL. */
- if (for_power_collapse && tgt_s->a11clk_khz < cur_s->a11clk_khz) {
- while (tgt_s->pll != ACPU_PLL_TCXO && tgt_s->pll != cur_s->pll)
- tgt_s--;
- }
-
- if (strt_s->pll != ACPU_PLL_TCXO)
- plls_enabled |= 1 << strt_s->pll;
-
- if (!for_power_collapse) {
- mutex_lock(&drv_state.lock);
- if (strt_s->pll != tgt_s->pll && tgt_s->pll != ACPU_PLL_TCXO) {
- rc = pc_pll_request(tgt_s->pll, 1);
- if (rc < 0) {
- pr_err("PLL%d enable failed (%d)\n",
- tgt_s->pll, rc);
- goto out;
- }
- plls_enabled |= 1 << tgt_s->pll;
- }
- /* Increase VDD if needed. */
- if (tgt_s->vdd > cur_s->vdd) {
- if ((rc = acpuclk_set_vdd_level(tgt_s->vdd)) < 0) {
- printk(KERN_ERR "Unable to switch ACPU vdd\n");
- goto out;
- }
- }
- }
-
- /* Set wait states for CPU between frequency changes */
- reg_clkctl = readl(A11S_CLK_CNTL_ADDR);
- reg_clkctl |= (100 << 16); /* set WT_ST_CNT */
- writel(reg_clkctl, A11S_CLK_CNTL_ADDR);
-
-#if PERF_SWITCH_DEBUG
- printk(KERN_INFO "acpuclock: Switching from ACPU rate %u -> %u\n",
- strt_s->a11clk_khz * 1000, tgt_s->a11clk_khz * 1000);
-#endif
-
- while (cur_s != tgt_s) {
- /*
- * Always jump to target freq if within 256mhz, regulardless of
- * PLL. If differnece is greater, use the predefinied
- * steppings in the table.
- */
- int d = abs((int)(cur_s->a11clk_khz - tgt_s->a11clk_khz));
- if (d > drv_state.max_speed_delta_khz) {
- /* Step up or down depending on target vs current. */
- int clk_index = tgt_s->a11clk_khz > cur_s->a11clk_khz ?
- cur_s->up : cur_s->down;
- if (clk_index < 0) { /* This should not happen. */
- printk(KERN_ERR "cur:%u target: %u\n",
- cur_s->a11clk_khz, tgt_s->a11clk_khz);
- rc = -EINVAL;
- goto out;
- }
- cur_s = &acpu_freq_tbl[clk_index];
- } else {
- cur_s = tgt_s;
- }
-#if PERF_SWITCH_STEP_DEBUG
- printk(KERN_DEBUG "%s: STEP khz = %u, pll = %d\n",
- __FUNCTION__, cur_s->a11clk_khz, cur_s->pll);
-#endif
- if (!for_power_collapse&& cur_s->pll != ACPU_PLL_TCXO
- && !(plls_enabled & (1 << cur_s->pll))) {
- rc = pc_pll_request(cur_s->pll, 1);
- if (rc < 0) {
- pr_err("PLL%d enable failed (%d)\n",
- cur_s->pll, rc);
- goto out;
- }
- plls_enabled |= 1 << cur_s->pll;
- }
-
- acpuclk_set_div(cur_s);
- drv_state.current_speed = cur_s;
- /* Re-adjust lpj for the new clock speed. */
- loops_per_jiffy = cur_s->lpj;
- udelay(drv_state.acpu_switch_time_us);
- }
-
- /* Nothing else to do for power collapse. */
- if (for_power_collapse)
- return 0;
-
- /* Disable PLLs we are not using anymore. */
- plls_enabled &= ~(1 << tgt_s->pll);
- for (pll = ACPU_PLL_0; pll <= ACPU_PLL_2; pll++)
- if (plls_enabled & (1 << pll)) {
- rc = pc_pll_request(pll, 0);
- if (rc < 0) {
- pr_err("PLL%d disable failed (%d)\n", pll, rc);
- goto out;
- }
- }
-
- /* Change the AXI bus frequency if we can. */
- if (strt_s->axiclk_khz != tgt_s->axiclk_khz) {
- rc = clk_set_rate(ebi1_clk, tgt_s->axiclk_khz * 1000);
- if (rc < 0)
- pr_err("Setting AXI min rate failed!\n");
- }
-
- /* Drop VDD level if we can. */
- if (tgt_s->vdd < strt_s->vdd) {
- if (acpuclk_set_vdd_level(tgt_s->vdd) < 0)
- printk(KERN_ERR "acpuclock: Unable to drop ACPU vdd\n");
- }
-
-#if PERF_SWITCH_DEBUG
- printk(KERN_DEBUG "%s: ACPU speed change complete\n", __FUNCTION__);
-#endif
-out:
- if (!for_power_collapse)
- mutex_unlock(&drv_state.lock);
- return rc;
-}
-
-static void __init acpuclk_init(void)
-{
- struct clkctl_acpu_speed *speed;
- uint32_t div, sel;
- int rc;
-
- /*
- * Determine the rate of ACPU clock
- */
-
- if (!(readl(A11S_CLK_SEL_ADDR) & 0x01)) { /* CLK_SEL_SRC1N0 */
- /* CLK_SRC0_SEL */
- sel = (readl(A11S_CLK_CNTL_ADDR) >> 12) & 0x7;
- /* CLK_SRC0_DIV */
- div = (readl(A11S_CLK_CNTL_ADDR) >> 8) & 0x0f;
- } else {
- /* CLK_SRC1_SEL */
- sel = (readl(A11S_CLK_CNTL_ADDR) >> 4) & 0x07;
- /* CLK_SRC1_DIV */
- div = readl(A11S_CLK_CNTL_ADDR) & 0x0f;
- }
-
- for (speed = acpu_freq_tbl; speed->a11clk_khz != 0; speed++) {
- if (speed->a11clk_src_sel == sel
- && (speed->a11clk_src_div == div))
- break;
- }
- if (speed->a11clk_khz == 0) {
- printk(KERN_WARNING "Warning - ACPU clock reports invalid speed\n");
- return;
- }
-
- drv_state.current_speed = speed;
-
- rc = clk_set_rate(ebi1_clk, speed->axiclk_khz * 1000);
- if (rc < 0)
- pr_err("Setting AXI min rate failed!\n");
-
- printk(KERN_INFO "ACPU running at %d KHz\n", speed->a11clk_khz);
-}
-
-unsigned long acpuclk_get_rate(void)
-{
- WARN_ONCE(drv_state.current_speed == NULL,
- "acpuclk_get_rate: not initialized\n");
- if (drv_state.current_speed)
- return drv_state.current_speed->a11clk_khz;
- else
- return 0;
-}
-
-uint32_t acpuclk_get_switch_time(void)
-{
- return drv_state.acpu_switch_time_us;
-}
-
-/*----------------------------------------------------------------------------
- * Clock driver initialization
- *---------------------------------------------------------------------------*/
-
-/* Initialize the lpj field in the acpu_freq_tbl. */
-static void __init lpj_init(void)
-{
- int i;
- const struct clkctl_acpu_speed *base_clk = drv_state.current_speed;
- for (i = 0; acpu_freq_tbl[i].a11clk_khz; i++) {
- acpu_freq_tbl[i].lpj = cpufreq_scale(loops_per_jiffy,
- base_clk->a11clk_khz,
- acpu_freq_tbl[i].a11clk_khz);
- }
-}
-
-void __init msm_acpu_clock_init(struct msm_acpu_clock_platform_data *clkdata)
-{
- pr_info("acpu_clock_init()\n");
-
- ebi1_clk = clk_get(NULL, "ebi1_clk");
-
- mutex_init(&drv_state.lock);
- drv_state.acpu_switch_time_us = clkdata->acpu_switch_time_us;
- drv_state.max_speed_delta_khz = clkdata->max_speed_delta_khz;
- drv_state.vdd_switch_time_us = clkdata->vdd_switch_time_us;
- drv_state.power_collapse_khz = clkdata->power_collapse_khz;
- drv_state.wait_for_irq_khz = clkdata->wait_for_irq_khz;
- acpuclk_init();
- lpj_init();
-#ifdef CONFIG_CPU_FREQ_TABLE
- cpufreq_frequency_table_get_attr(freq_table, smp_processor_id());
-#endif
-}
diff --git a/arch/arm/mach-msm/acpuclock.h b/arch/arm/mach-msm/acpuclock.h
deleted file mode 100644
index 415de2e..0000000
--- a/arch/arm/mach-msm/acpuclock.h
+++ /dev/null
@@ -1,32 +0,0 @@
-/* arch/arm/mach-msm/acpuclock.h
- *
- * MSM architecture clock driver header
- *
- * Copyright (C) 2007 Google, Inc.
- * Copyright (c) 2007 QUALCOMM Incorporated
- * Author: San Mehat <san at android.com>
- *
- * This software is licensed under the terms of the GNU General Public
- * License version 2, as published by the Free Software Foundation, and
- * may be copied, distributed, and modified under those terms.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- */
-
-#ifndef __ARCH_ARM_MACH_MSM_ACPUCLOCK_H
-#define __ARCH_ARM_MACH_MSM_ACPUCLOCK_H
-
-int acpuclk_set_rate(unsigned long rate, int for_power_collapse);
-unsigned long acpuclk_get_rate(void);
-uint32_t acpuclk_get_switch_time(void);
-unsigned long acpuclk_wait_for_irq(void);
-unsigned long acpuclk_power_collapse(void);
-unsigned long acpuclk_get_wfi_rate(void);
-
-
-#endif
-
diff --git a/arch/arm/mach-msm/board-halibut.c b/arch/arm/mach-msm/board-halibut.c
deleted file mode 100644
index a60ab6d..0000000
--- a/arch/arm/mach-msm/board-halibut.c
+++ /dev/null
@@ -1,102 +0,0 @@
-/* linux/arch/arm/mach-msm/board-halibut.c
- *
- * Copyright (C) 2007 Google, Inc.
- * Author: Brian Swetland <swetland at google.com>
- *
- * This software is licensed under the terms of the GNU General Public
- * License version 2, as published by the Free Software Foundation, and
- * may be copied, distributed, and modified under those terms.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/input.h>
-#include <linux/io.h>
-#include <linux/delay.h>
-
-#include <mach/hardware.h>
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-#include <asm/mach/flash.h>
-#include <asm/setup.h>
-
-#include <mach/irqs.h>
-#include <mach/board.h>
-#include <mach/msm_iomap.h>
-
-#include <linux/mtd/nand.h>
-#include <linux/mtd/partitions.h>
-
-#include "devices.h"
-
-static struct resource smc91x_resources[] = {
- [0] = {
- .start = 0x9C004300,
- .end = 0x9C004400,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = MSM_GPIO_TO_INT(49),
- .end = MSM_GPIO_TO_INT(49),
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device smc91x_device = {
- .name = "smc91x",
- .id = 0,
- .num_resources = ARRAY_SIZE(smc91x_resources),
- .resource = smc91x_resources,
-};
-
-static struct platform_device *devices[] __initdata = {
- &msm_device_uart3,
- &msm_device_smd,
- &msm_device_nand,
- &msm_device_hsusb,
- &msm_device_i2c,
- &smc91x_device,
-};
-
-extern struct sys_timer msm_timer;
-
-static void __init halibut_init_irq(void)
-{
- msm_init_irq();
-}
-
-static void __init halibut_init(void)
-{
- platform_add_devices(devices, ARRAY_SIZE(devices));
-}
-
-static void __init halibut_fixup(struct tag *tags, char **cmdline,
- struct meminfo *mi)
-{
- mi->nr_banks=1;
- mi->bank[0].start = PHYS_OFFSET;
- mi->bank[0].size = (101*1024*1024);
-}
-
-static void __init halibut_map_io(void)
-{
- msm_map_common_io();
- msm_clock_init(msm_clocks_7x01a, msm_num_clocks_7x01a);
-}
-
-MACHINE_START(HALIBUT, "Halibut Board (QCT SURF7200A)")
- .atag_offset = 0x100,
- .fixup = halibut_fixup,
- .map_io = halibut_map_io,
- .init_irq = halibut_init_irq,
- .init_machine = halibut_init,
- .timer = &msm_timer,
-MACHINE_END
diff --git a/arch/arm/mach-msm/board-trout-gpio.c b/arch/arm/mach-msm/board-trout-gpio.c
deleted file mode 100644
index 87e1d01..0000000
--- a/arch/arm/mach-msm/board-trout-gpio.c
+++ /dev/null
@@ -1,233 +0,0 @@
-/*
- * linux/arch/arm/mach-msm/gpio.c
- *
- * Copyright (C) 2005 HP Labs
- * Copyright (C) 2008 Google, Inc.
- * Copyright (C) 2009 Pavel Machek <pavel at ucw.cz>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- */
-
-#include <linux/kernel.h>
-#include <linux/module.h>
-#include <linux/io.h>
-#include <linux/irq.h>
-#include <linux/interrupt.h>
-#include <linux/gpio.h>
-
-#include "board-trout.h"
-
-static uint8_t trout_int_mask[2] = {
- [0] = 0xff, /* mask all interrupts */
- [1] = 0xff,
-};
-static uint8_t trout_sleep_int_mask[] = {
- [0] = 0xff,
- [1] = 0xff,
-};
-
-struct msm_gpio_chip {
- struct gpio_chip chip;
- void __iomem *reg; /* Base of register bank */
- u8 shadow;
-};
-
-#define to_msm_gpio_chip(c) container_of(c, struct msm_gpio_chip, chip)
-
-static int msm_gpiolib_get(struct gpio_chip *chip, unsigned offset)
-{
- struct msm_gpio_chip *msm_gpio = to_msm_gpio_chip(chip);
- unsigned mask = 1 << offset;
-
- return !!(readb(msm_gpio->reg) & mask);
-}
-
-static void msm_gpiolib_set(struct gpio_chip *chip, unsigned offset, int val)
-{
- struct msm_gpio_chip *msm_gpio = to_msm_gpio_chip(chip);
- unsigned mask = 1 << offset;
-
- if (val)
- msm_gpio->shadow |= mask;
- else
- msm_gpio->shadow &= ~mask;
-
- writeb(msm_gpio->shadow, msm_gpio->reg);
-}
-
-static int msm_gpiolib_direction_input(struct gpio_chip *chip,
- unsigned offset)
-{
- msm_gpiolib_set(chip, offset, 0);
- return 0;
-}
-
-static int msm_gpiolib_direction_output(struct gpio_chip *chip,
- unsigned offset, int val)
-{
- msm_gpiolib_set(chip, offset, val);
- return 0;
-}
-
-static int trout_gpio_to_irq(struct gpio_chip *chip, unsigned offset)
-{
- return TROUT_GPIO_TO_INT(offset + chip->base);
-}
-
-#define TROUT_GPIO_BANK(name, reg_num, base_gpio, shadow_val) \
- { \
- .chip = { \
- .label = name, \
- .direction_input = msm_gpiolib_direction_input,\
- .direction_output = msm_gpiolib_direction_output, \
- .get = msm_gpiolib_get, \
- .set = msm_gpiolib_set, \
- .to_irq = trout_gpio_to_irq, \
- .base = base_gpio, \
- .ngpio = 8, \
- }, \
- .reg = (void *) reg_num + TROUT_CPLD_BASE, \
- .shadow = shadow_val, \
- }
-
-static struct msm_gpio_chip msm_gpio_banks[] = {
-#if defined(CONFIG_MSM_DEBUG_UART1)
- /* H2W pins <-> UART1 */
- TROUT_GPIO_BANK("MISC2", 0x00, TROUT_GPIO_MISC2_BASE, 0x40),
-#else
- /* H2W pins <-> UART3, Bluetooth <-> UART1 */
- TROUT_GPIO_BANK("MISC2", 0x00, TROUT_GPIO_MISC2_BASE, 0x80),
-#endif
- /* I2C pull */
- TROUT_GPIO_BANK("MISC3", 0x02, TROUT_GPIO_MISC3_BASE, 0x04),
- TROUT_GPIO_BANK("MISC4", 0x04, TROUT_GPIO_MISC4_BASE, 0),
- /* mmdi 32k en */
- TROUT_GPIO_BANK("MISC5", 0x06, TROUT_GPIO_MISC5_BASE, 0x04),
- TROUT_GPIO_BANK("INT2", 0x08, TROUT_GPIO_INT2_BASE, 0),
- TROUT_GPIO_BANK("MISC1", 0x0a, TROUT_GPIO_MISC1_BASE, 0),
- TROUT_GPIO_BANK("VIRTUAL", 0x12, TROUT_GPIO_VIRTUAL_BASE, 0),
-};
-
-static void trout_gpio_irq_ack(struct irq_data *d)
-{
- int bank = TROUT_INT_TO_BANK(d->irq);
- uint8_t mask = TROUT_INT_TO_MASK(d->irq);
- int reg = TROUT_BANK_TO_STAT_REG(bank);
- /*printk(KERN_INFO "trout_gpio_irq_ack irq %d\n", d->irq);*/
- writeb(mask, TROUT_CPLD_BASE + reg);
-}
-
-static void trout_gpio_irq_mask(struct irq_data *d)
-{
- unsigned long flags;
- uint8_t reg_val;
- int bank = TROUT_INT_TO_BANK(d->irq);
- uint8_t mask = TROUT_INT_TO_MASK(d->irq);
- int reg = TROUT_BANK_TO_MASK_REG(bank);
-
- local_irq_save(flags);
- reg_val = trout_int_mask[bank] |= mask;
- /*printk(KERN_INFO "trout_gpio_irq_mask irq %d => %d:%02x\n",
- d->irq, bank, reg_val);*/
- writeb(reg_val, TROUT_CPLD_BASE + reg);
- local_irq_restore(flags);
-}
-
-static void trout_gpio_irq_unmask(struct irq_data *d)
-{
- unsigned long flags;
- uint8_t reg_val;
- int bank = TROUT_INT_TO_BANK(d->irq);
- uint8_t mask = TROUT_INT_TO_MASK(d->irq);
- int reg = TROUT_BANK_TO_MASK_REG(bank);
-
- local_irq_save(flags);
- reg_val = trout_int_mask[bank] &= ~mask;
- /*printk(KERN_INFO "trout_gpio_irq_unmask irq %d => %d:%02x\n",
- d->irq, bank, reg_val);*/
- writeb(reg_val, TROUT_CPLD_BASE + reg);
- local_irq_restore(flags);
-}
-
-int trout_gpio_irq_set_wake(struct irq_data *d, unsigned int on)
-{
- unsigned long flags;
- int bank = TROUT_INT_TO_BANK(d->irq);
- uint8_t mask = TROUT_INT_TO_MASK(d->irq);
-
- local_irq_save(flags);
- if(on)
- trout_sleep_int_mask[bank] &= ~mask;
- else
- trout_sleep_int_mask[bank] |= mask;
- local_irq_restore(flags);
- return 0;
-}
-
-static void trout_gpio_irq_handler(unsigned int irq, struct irq_desc *desc)
-{
- int j, m;
- unsigned v;
- int bank;
- int stat_reg;
- int int_base = TROUT_INT_START;
- uint8_t int_mask;
-
- for (bank = 0; bank < 2; bank++) {
- stat_reg = TROUT_BANK_TO_STAT_REG(bank);
- v = readb(TROUT_CPLD_BASE + stat_reg);
- int_mask = trout_int_mask[bank];
- if (v & int_mask) {
- writeb(v & int_mask, TROUT_CPLD_BASE + stat_reg);
- printk(KERN_ERR "trout_gpio_irq_handler: got masked "
- "interrupt: %d:%02x\n", bank, v & int_mask);
- }
- v &= ~int_mask;
- while (v) {
- m = v & -v;
- j = fls(m) - 1;
- /*printk(KERN_INFO "msm_gpio_irq_handler %d:%02x %02x b"
- "it %d irq %d\n", bank, v, m, j, int_base + j);*/
- v &= ~m;
- generic_handle_irq(int_base + j);
- }
- int_base += TROUT_INT_BANK0_COUNT;
- }
- desc->irq_data.chip->irq_ack(&desc->irq_data);
-}
-
-static struct irq_chip trout_gpio_irq_chip = {
- .name = "troutgpio",
- .irq_ack = trout_gpio_irq_ack,
- .irq_mask = trout_gpio_irq_mask,
- .irq_unmask = trout_gpio_irq_unmask,
- .irq_set_wake = trout_gpio_irq_set_wake,
-};
-
-/*
- * Called from the processor-specific init to enable GPIO pin support.
- */
-int __init trout_init_gpio(void)
-{
- int i;
- for(i = TROUT_INT_START; i <= TROUT_INT_END; i++) {
- irq_set_chip_and_handler(i, &trout_gpio_irq_chip,
- handle_edge_irq);
- set_irq_flags(i, IRQF_VALID);
- }
-
- for (i = 0; i < ARRAY_SIZE(msm_gpio_banks); i++)
- gpiochip_add(&msm_gpio_banks[i].chip);
-
- irq_set_irq_type(MSM_GPIO_TO_INT(17), IRQF_TRIGGER_HIGH);
- irq_set_chained_handler(MSM_GPIO_TO_INT(17), trout_gpio_irq_handler);
- irq_set_irq_wake(MSM_GPIO_TO_INT(17), 1);
-
- return 0;
-}
-
-postcore_initcall(trout_init_gpio);
-
diff --git a/arch/arm/mach-msm/board-trout-mmc.c b/arch/arm/mach-msm/board-trout-mmc.c
deleted file mode 100644
index 8650342..0000000
--- a/arch/arm/mach-msm/board-trout-mmc.c
+++ /dev/null
@@ -1,185 +0,0 @@
-/* linux/arch/arm/mach-msm/board-trout-mmc.c
-** Author: Brian Swetland <swetland at google.com>
-*/
-#include <linux/gpio.h>
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/delay.h>
-#include <linux/mmc/host.h>
-#include <linux/mmc/sdio_ids.h>
-#include <linux/err.h>
-#include <linux/debugfs.h>
-
-#include <asm/io.h>
-
-#include <mach/vreg.h>
-
-#include <mach/mmc.h>
-
-#include "devices.h"
-
-#include "board-trout.h"
-
-#include "proc_comm.h"
-
-#define DEBUG_SDSLOT_VDD 1
-
-/* ---- COMMON ---- */
-static void config_gpio_table(uint32_t *table, int len)
-{
- int n;
- unsigned id;
- for(n = 0; n < len; n++) {
- id = table[n];
- msm_proc_comm(PCOM_RPC_GPIO_TLMM_CONFIG_EX, &id, 0);
- }
-}
-
-/* ---- SDCARD ---- */
-
-static uint32_t sdcard_on_gpio_table[] = {
- PCOM_GPIO_CFG(62, 2, GPIO_OUTPUT, GPIO_NO_PULL, GPIO_8MA), /* CLK */
- PCOM_GPIO_CFG(63, 2, GPIO_OUTPUT, GPIO_PULL_UP, GPIO_8MA), /* CMD */
- PCOM_GPIO_CFG(64, 2, GPIO_OUTPUT, GPIO_PULL_UP, GPIO_8MA), /* DAT3 */
- PCOM_GPIO_CFG(65, 2, GPIO_OUTPUT, GPIO_PULL_UP, GPIO_8MA), /* DAT2 */
- PCOM_GPIO_CFG(66, 2, GPIO_OUTPUT, GPIO_PULL_UP, GPIO_4MA), /* DAT1 */
- PCOM_GPIO_CFG(67, 2, GPIO_OUTPUT, GPIO_PULL_UP, GPIO_4MA), /* DAT0 */
-};
-
-static uint32_t sdcard_off_gpio_table[] = {
- PCOM_GPIO_CFG(62, 0, GPIO_OUTPUT, GPIO_NO_PULL, GPIO_4MA), /* CLK */
- PCOM_GPIO_CFG(63, 0, GPIO_OUTPUT, GPIO_NO_PULL, GPIO_4MA), /* CMD */
- PCOM_GPIO_CFG(64, 0, GPIO_OUTPUT, GPIO_NO_PULL, GPIO_4MA), /* DAT3 */
- PCOM_GPIO_CFG(65, 0, GPIO_OUTPUT, GPIO_NO_PULL, GPIO_4MA), /* DAT2 */
- PCOM_GPIO_CFG(66, 0, GPIO_OUTPUT, GPIO_NO_PULL, GPIO_4MA), /* DAT1 */
- PCOM_GPIO_CFG(67, 0, GPIO_OUTPUT, GPIO_NO_PULL, GPIO_4MA), /* DAT0 */
-};
-
-static uint opt_disable_sdcard;
-
-static int __init trout_disablesdcard_setup(char *str)
-{
- int cal = simple_strtol(str, NULL, 0);
-
- opt_disable_sdcard = cal;
- return 1;
-}
-
-__setup("board_trout.disable_sdcard=", trout_disablesdcard_setup);
-
-static struct vreg *vreg_sdslot; /* SD slot power */
-
-struct mmc_vdd_xlat {
- int mask;
- int level;
-};
-
-static struct mmc_vdd_xlat mmc_vdd_table[] = {
- { MMC_VDD_165_195, 1800 },
- { MMC_VDD_20_21, 2050 },
- { MMC_VDD_21_22, 2150 },
- { MMC_VDD_22_23, 2250 },
- { MMC_VDD_23_24, 2350 },
- { MMC_VDD_24_25, 2450 },
- { MMC_VDD_25_26, 2550 },
- { MMC_VDD_26_27, 2650 },
- { MMC_VDD_27_28, 2750 },
- { MMC_VDD_28_29, 2850 },
- { MMC_VDD_29_30, 2950 },
-};
-
-static unsigned int sdslot_vdd = 0xffffffff;
-static unsigned int sdslot_vreg_enabled;
-
-static uint32_t trout_sdslot_switchvdd(struct device *dev, unsigned int vdd)
-{
- int i, rc;
-
- BUG_ON(!vreg_sdslot);
-
- if (vdd == sdslot_vdd)
- return 0;
-
- sdslot_vdd = vdd;
-
- if (vdd == 0) {
-#if DEBUG_SDSLOT_VDD
- printk("%s: Disabling SD slot power\n", __func__);
-#endif
- config_gpio_table(sdcard_off_gpio_table,
- ARRAY_SIZE(sdcard_off_gpio_table));
- vreg_disable(vreg_sdslot);
- sdslot_vreg_enabled = 0;
- return 0;
- }
-
- if (!sdslot_vreg_enabled) {
- rc = vreg_enable(vreg_sdslot);
- if (rc) {
- printk(KERN_ERR "%s: Error enabling vreg (%d)\n",
- __func__, rc);
- }
- config_gpio_table(sdcard_on_gpio_table,
- ARRAY_SIZE(sdcard_on_gpio_table));
- sdslot_vreg_enabled = 1;
- }
-
- for (i = 0; i < ARRAY_SIZE(mmc_vdd_table); i++) {
- if (mmc_vdd_table[i].mask == (1 << vdd)) {
-#if DEBUG_SDSLOT_VDD
- printk("%s: Setting level to %u\n",
- __func__, mmc_vdd_table[i].level);
-#endif
- rc = vreg_set_level(vreg_sdslot,
- mmc_vdd_table[i].level);
- if (rc) {
- printk(KERN_ERR
- "%s: Error setting vreg level (%d)\n",
- __func__, rc);
- }
- return 0;
- }
- }
-
- printk(KERN_ERR "%s: Invalid VDD %d specified\n", __func__, vdd);
- return 0;
-}
-
-static unsigned int trout_sdslot_status(struct device *dev)
-{
- unsigned int status;
-
- status = (unsigned int) gpio_get_value(TROUT_GPIO_SDMC_CD_N);
- return (!status);
-}
-
-#define TROUT_MMC_VDD MMC_VDD_165_195 | MMC_VDD_20_21 | MMC_VDD_21_22 \
- | MMC_VDD_22_23 | MMC_VDD_23_24 | MMC_VDD_24_25 \
- | MMC_VDD_25_26 | MMC_VDD_26_27 | MMC_VDD_27_28 \
- | MMC_VDD_28_29 | MMC_VDD_29_30
-
-static struct msm_mmc_platform_data trout_sdslot_data = {
- .ocr_mask = TROUT_MMC_VDD,
- .status = trout_sdslot_status,
- .translate_vdd = trout_sdslot_switchvdd,
-};
-
-int __init trout_init_mmc(unsigned int sys_rev)
-{
- sdslot_vreg_enabled = 0;
-
- vreg_sdslot = vreg_get(0, "gp6");
- if (IS_ERR(vreg_sdslot))
- return PTR_ERR(vreg_sdslot);
-
- irq_set_irq_wake(TROUT_GPIO_TO_INT(TROUT_GPIO_SDMC_CD_N), 1);
-
- if (!opt_disable_sdcard)
- msm_add_sdcc(2, &trout_sdslot_data,
- TROUT_GPIO_TO_INT(TROUT_GPIO_SDMC_CD_N), 0);
- else
- printk(KERN_INFO "trout: SD-Card interface disabled\n");
- return 0;
-}
-
diff --git a/arch/arm/mach-msm/board-trout-panel.c b/arch/arm/mach-msm/board-trout-panel.c
deleted file mode 100644
index 25105c1..0000000
--- a/arch/arm/mach-msm/board-trout-panel.c
+++ /dev/null
@@ -1,296 +0,0 @@
-/* linux/arch/arm/mach-msm/board-trout-mddi.c
-** Author: Brian Swetland <swetland at google.com>
-*/
-#include <linux/gpio.h>
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/delay.h>
-#include <linux/leds.h>
-#include <linux/clk.h>
-#include <linux/err.h>
-
-#include <asm/io.h>
-#include <asm/mach-types.h>
-
-#include <mach/msm_fb.h>
-#include <mach/vreg.h>
-
-#include "board-trout.h"
-#include "proc_comm.h"
-#include "devices.h"
-
-#define TROUT_DEFAULT_BACKLIGHT_BRIGHTNESS 255
-
-#define MDDI_CLIENT_CORE_BASE 0x108000
-#define LCD_CONTROL_BLOCK_BASE 0x110000
-#define SPI_BLOCK_BASE 0x120000
-#define I2C_BLOCK_BASE 0x130000
-#define PWM_BLOCK_BASE 0x140000
-#define GPIO_BLOCK_BASE 0x150000
-#define SYSTEM_BLOCK1_BASE 0x160000
-#define SYSTEM_BLOCK2_BASE 0x170000
-
-
-#define DPSUS (MDDI_CLIENT_CORE_BASE|0x24)
-#define SYSCLKENA (MDDI_CLIENT_CORE_BASE|0x2C)
-#define PWM0OFF (PWM_BLOCK_BASE|0x1C)
-
-#define V_VDDE2E_VDD2_GPIO 0
-#define MDDI_RST_N 82
-
-#define MDDICAP0 (MDDI_CLIENT_CORE_BASE|0x00)
-#define MDDICAP1 (MDDI_CLIENT_CORE_BASE|0x04)
-#define MDDICAP2 (MDDI_CLIENT_CORE_BASE|0x08)
-#define MDDICAP3 (MDDI_CLIENT_CORE_BASE|0x0C)
-#define MDCAPCHG (MDDI_CLIENT_CORE_BASE|0x10)
-#define MDCRCERC (MDDI_CLIENT_CORE_BASE|0x14)
-#define TTBUSSEL (MDDI_CLIENT_CORE_BASE|0x18)
-#define DPSET0 (MDDI_CLIENT_CORE_BASE|0x1C)
-#define DPSET1 (MDDI_CLIENT_CORE_BASE|0x20)
-#define DPSUS (MDDI_CLIENT_CORE_BASE|0x24)
-#define DPRUN (MDDI_CLIENT_CORE_BASE|0x28)
-#define SYSCKENA (MDDI_CLIENT_CORE_BASE|0x2C)
-#define TESTMODE (MDDI_CLIENT_CORE_BASE|0x30)
-#define FIFOMONI (MDDI_CLIENT_CORE_BASE|0x34)
-#define INTMONI (MDDI_CLIENT_CORE_BASE|0x38)
-#define MDIOBIST (MDDI_CLIENT_CORE_BASE|0x3C)
-#define MDIOPSET (MDDI_CLIENT_CORE_BASE|0x40)
-#define BITMAP0 (MDDI_CLIENT_CORE_BASE|0x44)
-#define BITMAP1 (MDDI_CLIENT_CORE_BASE|0x48)
-#define BITMAP2 (MDDI_CLIENT_CORE_BASE|0x4C)
-#define BITMAP3 (MDDI_CLIENT_CORE_BASE|0x50)
-#define BITMAP4 (MDDI_CLIENT_CORE_BASE|0x54)
-
-#define SRST (LCD_CONTROL_BLOCK_BASE|0x00)
-#define PORT_ENB (LCD_CONTROL_BLOCK_BASE|0x04)
-#define START (LCD_CONTROL_BLOCK_BASE|0x08)
-#define PORT (LCD_CONTROL_BLOCK_BASE|0x0C)
-#define CMN (LCD_CONTROL_BLOCK_BASE|0x10)
-#define GAMMA (LCD_CONTROL_BLOCK_BASE|0x14)
-#define INTFLG (LCD_CONTROL_BLOCK_BASE|0x18)
-#define INTMSK (LCD_CONTROL_BLOCK_BASE|0x1C)
-#define MPLFBUF (LCD_CONTROL_BLOCK_BASE|0x20)
-#define HDE_LEFT (LCD_CONTROL_BLOCK_BASE|0x24)
-#define VDE_TOP (LCD_CONTROL_BLOCK_BASE|0x28)
-#define PXL (LCD_CONTROL_BLOCK_BASE|0x30)
-#define HCYCLE (LCD_CONTROL_BLOCK_BASE|0x34)
-#define HSW (LCD_CONTROL_BLOCK_BASE|0x38)
-#define HDE_START (LCD_CONTROL_BLOCK_BASE|0x3C)
-#define HDE_SIZE (LCD_CONTROL_BLOCK_BASE|0x40)
-#define VCYCLE (LCD_CONTROL_BLOCK_BASE|0x44)
-#define VSW (LCD_CONTROL_BLOCK_BASE|0x48)
-#define VDE_START (LCD_CONTROL_BLOCK_BASE|0x4C)
-#define VDE_SIZE (LCD_CONTROL_BLOCK_BASE|0x50)
-#define WAKEUP (LCD_CONTROL_BLOCK_BASE|0x54)
-#define WSYN_DLY (LCD_CONTROL_BLOCK_BASE|0x58)
-#define REGENB (LCD_CONTROL_BLOCK_BASE|0x5C)
-#define VSYNIF (LCD_CONTROL_BLOCK_BASE|0x60)
-#define WRSTB (LCD_CONTROL_BLOCK_BASE|0x64)
-#define RDSTB (LCD_CONTROL_BLOCK_BASE|0x68)
-#define ASY_DATA (LCD_CONTROL_BLOCK_BASE|0x6C)
-#define ASY_DATB (LCD_CONTROL_BLOCK_BASE|0x70)
-#define ASY_DATC (LCD_CONTROL_BLOCK_BASE|0x74)
-#define ASY_DATD (LCD_CONTROL_BLOCK_BASE|0x78)
-#define ASY_DATE (LCD_CONTROL_BLOCK_BASE|0x7C)
-#define ASY_DATF (LCD_CONTROL_BLOCK_BASE|0x80)
-#define ASY_DATG (LCD_CONTROL_BLOCK_BASE|0x84)
-#define ASY_DATH (LCD_CONTROL_BLOCK_BASE|0x88)
-#define ASY_CMDSET (LCD_CONTROL_BLOCK_BASE|0x8C)
-
-#define SSICTL (SPI_BLOCK_BASE|0x00)
-#define SSITIME (SPI_BLOCK_BASE|0x04)
-#define SSITX (SPI_BLOCK_BASE|0x08)
-#define SSIRX (SPI_BLOCK_BASE|0x0C)
-#define SSIINTC (SPI_BLOCK_BASE|0x10)
-#define SSIINTS (SPI_BLOCK_BASE|0x14)
-#define SSIDBG1 (SPI_BLOCK_BASE|0x18)
-#define SSIDBG2 (SPI_BLOCK_BASE|0x1C)
-#define SSIID (SPI_BLOCK_BASE|0x20)
-
-#define WKREQ (SYSTEM_BLOCK1_BASE|0x00)
-#define CLKENB (SYSTEM_BLOCK1_BASE|0x04)
-#define DRAMPWR (SYSTEM_BLOCK1_BASE|0x08)
-#define INTMASK (SYSTEM_BLOCK1_BASE|0x0C)
-#define GPIOSEL (SYSTEM_BLOCK2_BASE|0x00)
-
-#define GPIODATA (GPIO_BLOCK_BASE|0x00)
-#define GPIODIR (GPIO_BLOCK_BASE|0x04)
-#define GPIOIS (GPIO_BLOCK_BASE|0x08)
-#define GPIOIBE (GPIO_BLOCK_BASE|0x0C)
-#define GPIOIEV (GPIO_BLOCK_BASE|0x10)
-#define GPIOIE (GPIO_BLOCK_BASE|0x14)
-#define GPIORIS (GPIO_BLOCK_BASE|0x18)
-#define GPIOMIS (GPIO_BLOCK_BASE|0x1C)
-#define GPIOIC (GPIO_BLOCK_BASE|0x20)
-#define GPIOOMS (GPIO_BLOCK_BASE|0x24)
-#define GPIOPC (GPIO_BLOCK_BASE|0x28)
-#define GPIOID (GPIO_BLOCK_BASE|0x30)
-
-#define SPI_WRITE(reg, val) \
- { SSITX, 0x00010000 | (((reg) & 0xff) << 8) | ((val) & 0xff) }, \
- { 0, 5 },
-
-#define SPI_WRITE1(reg) \
- { SSITX, (reg) & 0xff }, \
- { 0, 5 },
-
-struct mddi_table {
- uint32_t reg;
- uint32_t value;
-};
-static struct mddi_table mddi_toshiba_init_table[] = {
- { DPSET0, 0x09e90046 },
- { DPSET1, 0x00000118 },
- { DPSUS, 0x00000000 },
- { DPRUN, 0x00000001 },
- { 1, 14 }, /* msleep 14 */
- { SYSCKENA, 0x00000001 },
- { CLKENB, 0x0000A1EF }, /* # SYS.CLKENB # Enable clocks for each module (without DCLK , i2cCLK) */
-
- { GPIODATA, 0x02000200 }, /* # GPI .GPIODATA # GPIO2(RESET_LCD_N) set to 0 , GPIO3(eDRAM_Power) set to 0 */
- { GPIODIR, 0x000030D }, /* 24D # GPI .GPIODIR # Select direction of GPIO port (0,2,3,6,9 output) */
- { GPIOSEL, 0/*0x00000173*/}, /* # SYS.GPIOSEL # GPIO port multiplexing control */
- { GPIOPC, 0x03C300C0 }, /* # GPI .GPIOPC # GPIO2,3 PD cut */
- { WKREQ, 0x00000000 }, /* # SYS.WKREQ # Wake-up request event is VSYNC alignment */
-
- { GPIOIBE, 0x000003FF },
- { GPIOIS, 0x00000000 },
- { GPIOIC, 0x000003FF },
- { GPIOIE, 0x00000000 },
-
- { GPIODATA, 0x00040004 }, /* # GPI .GPIODATA # eDRAM VD supply */
- { 1, 1 }, /* msleep 1 */
- { GPIODATA, 0x02040004 }, /* # GPI .GPIODATA # eDRAM VD supply */
- { DRAMPWR, 0x00000001 }, /* eDRAM power */
-};
-
-#define GPIOSEL_VWAKEINT (1U << 0)
-#define INTMASK_VWAKEOUT (1U << 0)
-
-
-static struct clk *gp_clk;
-static int trout_new_backlight = 1;
-static struct vreg *vreg_mddi_1v5;
-static struct vreg *vreg_lcm_2v85;
-
-static void trout_process_mddi_table(struct msm_mddi_client_data *client_data,
- struct mddi_table *table, size_t count)
-{
- int i;
- for (i = 0; i < count; i++) {
- uint32_t reg = table[i].reg;
- uint32_t value = table[i].value;
-
- if (reg == 0)
- udelay(value);
- else if (reg == 1)
- msleep(value);
- else
- client_data->remote_write(client_data, value, reg);
- }
-}
-
-static int trout_mddi_toshiba_client_init(
- struct msm_mddi_bridge_platform_data *bridge_data,
- struct msm_mddi_client_data *client_data)
-{
- int panel_id;
-
- client_data->auto_hibernate(client_data, 0);
- trout_process_mddi_table(client_data, mddi_toshiba_init_table,
- ARRAY_SIZE(mddi_toshiba_init_table));
- client_data->auto_hibernate(client_data, 1);
- panel_id = (client_data->remote_read(client_data, GPIODATA) >> 4) & 3;
- if (panel_id > 1) {
- printk(KERN_WARNING "unknown panel id at mddi_enable\n");
- return -1;
- }
- return 0;
-}
-
-static int trout_mddi_toshiba_client_uninit(
- struct msm_mddi_bridge_platform_data *bridge_data,
- struct msm_mddi_client_data *client_data)
-{
- return 0;
-}
-
-static struct resource resources_msm_fb[] = {
- {
- .start = MSM_FB_BASE,
- .end = MSM_FB_BASE + MSM_FB_SIZE,
- .flags = IORESOURCE_MEM,
- },
-};
-
-struct msm_mddi_bridge_platform_data toshiba_client_data = {
- .init = trout_mddi_toshiba_client_init,
- .uninit = trout_mddi_toshiba_client_uninit,
- .fb_data = {
- .xres = 320,
- .yres = 480,
- .width = 45,
- .height = 67,
- .output_format = 0,
- },
-};
-
-static struct msm_mddi_platform_data mddi_pdata = {
- .clk_rate = 122880000,
- .fb_resource = resources_msm_fb,
- .num_clients = 1,
- .client_platform_data = {
- {
- .product_id = (0xd263 << 16 | 0),
- .name = "mddi_c_d263_0000",
- .id = 0,
- .client_data = &toshiba_client_data,
- .clk_rate = 0,
- },
- },
-};
-
-int __init trout_init_panel(void)
-{
- int rc;
-
- if (!machine_is_trout())
- return 0;
- vreg_mddi_1v5 = vreg_get(0, "gp2");
- if (IS_ERR(vreg_mddi_1v5))
- return PTR_ERR(vreg_mddi_1v5);
- vreg_lcm_2v85 = vreg_get(0, "gp4");
- if (IS_ERR(vreg_lcm_2v85))
- return PTR_ERR(vreg_lcm_2v85);
-
- trout_new_backlight = system_rev >= 5;
- if (trout_new_backlight) {
- uint32_t config = PCOM_GPIO_CFG(27, 0, GPIO_OUTPUT,
- GPIO_NO_PULL, GPIO_8MA);
- msm_proc_comm(PCOM_RPC_GPIO_TLMM_CONFIG_EX, &config, 0);
- } else {
- uint32_t config = PCOM_GPIO_CFG(27, 1, GPIO_OUTPUT,
- GPIO_NO_PULL, GPIO_8MA);
- msm_proc_comm(PCOM_RPC_GPIO_TLMM_CONFIG_EX, &config, 0);
-
- gp_clk = clk_get(NULL, "gp_clk");
- if (IS_ERR(gp_clk)) {
- printk(KERN_ERR "trout_init_panel: could not get gp"
- "clock\n");
- gp_clk = NULL;
- }
- rc = clk_set_rate(gp_clk, 19200000);
- if (rc)
- printk(KERN_ERR "trout_init_panel: set clock rate "
- "failed\n");
- }
-
- rc = platform_device_register(&msm_device_mdp);
- if (rc)
- return rc;
- msm_device_mddi0.dev.platform_data = &mddi_pdata;
- return platform_device_register(&msm_device_mddi0);
-}
-
-device_initcall(trout_init_panel);
diff --git a/arch/arm/mach-msm/board-trout.c b/arch/arm/mach-msm/board-trout.c
deleted file mode 100644
index 6b9b227..0000000
--- a/arch/arm/mach-msm/board-trout.c
+++ /dev/null
@@ -1,102 +0,0 @@
-/* linux/arch/arm/mach-msm/board-trout.c
- *
- * Copyright (C) 2009 Google, Inc.
- * Author: Brian Swetland <swetland at google.com>
- *
- * This software is licensed under the terms of the GNU General Public
- * License version 2, as published by the Free Software Foundation, and
- * may be copied, distributed, and modified under those terms.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/clkdev.h>
-
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-#include <asm/setup.h>
-
-#include <mach/board.h>
-#include <mach/hardware.h>
-#include <mach/msm_iomap.h>
-
-#include "devices.h"
-#include "board-trout.h"
-
-extern int trout_init_mmc(unsigned int);
-
-static struct platform_device *devices[] __initdata = {
- &msm_device_uart3,
- &msm_device_smd,
- &msm_device_nand,
- &msm_device_hsusb,
- &msm_device_i2c,
-};
-
-extern struct sys_timer msm_timer;
-
-static void __init trout_init_irq(void)
-{
- msm_init_irq();
-}
-
-static void __init trout_fixup(struct tag *tags, char **cmdline,
- struct meminfo *mi)
-{
- mi->nr_banks = 1;
- mi->bank[0].start = PHYS_OFFSET;
- mi->bank[0].size = (101*1024*1024);
-}
-
-static void __init trout_init(void)
-{
- int rc;
-
- platform_add_devices(devices, ARRAY_SIZE(devices));
-
-#ifdef CONFIG_MMC
- rc = trout_init_mmc(system_rev);
- if (rc)
- printk(KERN_CRIT "%s: MMC init failure (%d)\n", __func__, rc);
-#endif
-
-}
-
-static struct map_desc trout_io_desc[] __initdata = {
- {
- .virtual = TROUT_CPLD_BASE,
- .pfn = __phys_to_pfn(TROUT_CPLD_START),
- .length = TROUT_CPLD_SIZE,
- .type = MT_DEVICE_NONSHARED
- }
-};
-
-static void __init trout_map_io(void)
-{
- msm_map_common_io();
- iotable_init(trout_io_desc, ARRAY_SIZE(trout_io_desc));
-
-#ifdef CONFIG_MSM_DEBUG_UART3
- /* route UART3 to the "H2W" extended usb connector */
- writeb(0x80, TROUT_CPLD_BASE + 0x00);
-#endif
-
- msm_clock_init(msm_clocks_7x01a, msm_num_clocks_7x01a);
-}
-
-MACHINE_START(TROUT, "HTC Dream")
- .atag_offset = 0x100,
- .fixup = trout_fixup,
- .map_io = trout_map_io,
- .init_irq = trout_init_irq,
- .init_machine = trout_init,
- .timer = &msm_timer,
-MACHINE_END
diff --git a/arch/arm/mach-msm/board-trout.h b/arch/arm/mach-msm/board-trout.h
deleted file mode 100644
index 651851c..0000000
--- a/arch/arm/mach-msm/board-trout.h
+++ /dev/null
@@ -1,162 +0,0 @@
-/* linux/arch/arm/mach-msm/board-trout.h
-** Author: Brian Swetland <swetland at google.com>
-*/
-#ifndef __ARCH_ARM_MACH_MSM_BOARD_TROUT_H
-#define __ARCH_ARM_MACH_MSM_BOARD_TROUT_H
-
-#include <mach/board.h>
-
-#define MSM_SMI_BASE 0x00000000
-#define MSM_SMI_SIZE 0x00800000
-
-#define MSM_EBI_BASE 0x10000000
-#define MSM_EBI_SIZE 0x06e00000
-
-#define MSM_PMEM_GPU0_BASE 0x00000000
-#define MSM_PMEM_GPU0_SIZE 0x00700000
-
-#define MSM_PMEM_MDP_BASE 0x02000000
-#define MSM_PMEM_MDP_SIZE 0x00800000
-
-#define MSM_PMEM_ADSP_BASE 0x02800000
-#define MSM_PMEM_ADSP_SIZE 0x00800000
-
-#define MSM_PMEM_CAMERA_BASE 0x03000000
-#define MSM_PMEM_CAMERA_SIZE 0x00800000
-
-#define MSM_FB_BASE 0x03800000
-#define MSM_FB_SIZE 0x00100000
-
-#define MSM_LINUX_BASE MSM_EBI_BASE
-#define MSM_LINUX_SIZE 0x06500000
-
-#define MSM_PMEM_GPU1_SIZE 0x800000
-#define MSM_PMEM_GPU1_BASE (MSM_RAM_CONSOLE_BASE - MSM_PMEM_GPU1_SIZE)
-
-#define MSM_RAM_CONSOLE_BASE (MSM_EBI_BASE + 0x6d00000)
-#define MSM_RAM_CONSOLE_SIZE (128 * SZ_1K)
-
-#if (MSM_FB_BASE + MSM_FB_SIZE) >= (MSM_PMEM_GPU1_BASE)
-#error invalid memory map
-#endif
-
-#define DECLARE_MSM_IOMAP
-#include <mach/msm_iomap.h>
-
-#define TROUT_4_BALL_UP_0 1
-#define TROUT_4_BALL_LEFT_0 18
-#define TROUT_4_BALL_DOWN_0 57
-#define TROUT_4_BALL_RIGHT_0 91
-
-#define TROUT_5_BALL_UP_0 94
-#define TROUT_5_BALL_LEFT_0 18
-#define TROUT_5_BALL_DOWN_0 90
-#define TROUT_5_BALL_RIGHT_0 19
-
-#define TROUT_POWER_KEY 20
-
-#define TROUT_4_TP_LS_EN 19
-#define TROUT_5_TP_LS_EN 1
-
-#define TROUT_CPLD_BASE 0xE8100000
-#define TROUT_CPLD_START 0x98000000
-#define TROUT_CPLD_SIZE SZ_4K
-
-#define TROUT_GPIO_CABLE_IN1 (83)
-#define TROUT_GPIO_CABLE_IN2 (49)
-
-#define TROUT_GPIO_START (128)
-
-#define TROUT_GPIO_INT_MASK0_REG (0x0c)
-#define TROUT_GPIO_INT_STAT0_REG (0x0e)
-#define TROUT_GPIO_INT_MASK1_REG (0x14)
-#define TROUT_GPIO_INT_STAT1_REG (0x10)
-
-#define TROUT_GPIO_HAPTIC_PWM (28)
-#define TROUT_GPIO_PS_HOLD (25)
-
-#define TROUT_GPIO_MISC2_BASE (TROUT_GPIO_START + 0x00)
-#define TROUT_GPIO_MISC3_BASE (TROUT_GPIO_START + 0x08)
-#define TROUT_GPIO_MISC4_BASE (TROUT_GPIO_START + 0x10)
-#define TROUT_GPIO_MISC5_BASE (TROUT_GPIO_START + 0x18)
-#define TROUT_GPIO_INT2_BASE (TROUT_GPIO_START + 0x20)
-#define TROUT_GPIO_MISC1_BASE (TROUT_GPIO_START + 0x28)
-#define TROUT_GPIO_VIRTUAL_BASE (TROUT_GPIO_START + 0x30)
-#define TROUT_GPIO_INT5_BASE (TROUT_GPIO_START + 0x48)
-
-#define TROUT_GPIO_CHARGER_EN (TROUT_GPIO_MISC2_BASE + 0)
-#define TROUT_GPIO_ISET (TROUT_GPIO_MISC2_BASE + 1)
-#define TROUT_GPIO_H2W_DAT_DIR (TROUT_GPIO_MISC2_BASE + 2)
-#define TROUT_GPIO_H2W_CLK_DIR (TROUT_GPIO_MISC2_BASE + 3)
-#define TROUT_GPIO_H2W_DAT_GPO (TROUT_GPIO_MISC2_BASE + 4)
-#define TROUT_GPIO_H2W_CLK_GPO (TROUT_GPIO_MISC2_BASE + 5)
-#define TROUT_GPIO_H2W_SEL0 (TROUT_GPIO_MISC2_BASE + 6)
-#define TROUT_GPIO_H2W_SEL1 (TROUT_GPIO_MISC2_BASE + 7)
-
-#define TROUT_GPIO_SPOTLIGHT_EN (TROUT_GPIO_MISC3_BASE + 0)
-#define TROUT_GPIO_FLASH_EN (TROUT_GPIO_MISC3_BASE + 1)
-#define TROUT_GPIO_I2C_PULL (TROUT_GPIO_MISC3_BASE + 2)
-#define TROUT_GPIO_TP_I2C_PULL (TROUT_GPIO_MISC3_BASE + 3)
-#define TROUT_GPIO_TP_EN (TROUT_GPIO_MISC3_BASE + 4)
-#define TROUT_GPIO_JOG_EN (TROUT_GPIO_MISC3_BASE + 5)
-#define TROUT_GPIO_UI_LED_EN (TROUT_GPIO_MISC3_BASE + 6)
-#define TROUT_GPIO_QTKEY_LED_EN (TROUT_GPIO_MISC3_BASE + 7)
-
-#define TROUT_GPIO_VCM_PWDN (TROUT_GPIO_MISC4_BASE + 0)
-#define TROUT_GPIO_USB_H2W_SW (TROUT_GPIO_MISC4_BASE + 1)
-#define TROUT_GPIO_COMPASS_RST_N (TROUT_GPIO_MISC4_BASE + 2)
-#define TROUT_GPIO_HAPTIC_EN_UP (TROUT_GPIO_MISC4_BASE + 3)
-#define TROUT_GPIO_HAPTIC_EN_MAIN (TROUT_GPIO_MISC4_BASE + 4)
-#define TROUT_GPIO_USB_PHY_RST_N (TROUT_GPIO_MISC4_BASE + 5)
-#define TROUT_GPIO_WIFI_PA_RESETX (TROUT_GPIO_MISC4_BASE + 6)
-#define TROUT_GPIO_WIFI_EN (TROUT_GPIO_MISC4_BASE + 7)
-
-#define TROUT_GPIO_BT_32K_EN (TROUT_GPIO_MISC5_BASE + 0)
-#define TROUT_GPIO_MAC_32K_EN (TROUT_GPIO_MISC5_BASE + 1)
-#define TROUT_GPIO_MDDI_32K_EN (TROUT_GPIO_MISC5_BASE + 2)
-#define TROUT_GPIO_COMPASS_32K_EN (TROUT_GPIO_MISC5_BASE + 3)
-
-#define TROUT_GPIO_NAVI_ACT_N (TROUT_GPIO_INT2_BASE + 0)
-#define TROUT_GPIO_COMPASS_IRQ (TROUT_GPIO_INT2_BASE + 1)
-#define TROUT_GPIO_SLIDING_DET (TROUT_GPIO_INT2_BASE + 2)
-#define TROUT_GPIO_AUD_HSMIC_DET_N (TROUT_GPIO_INT2_BASE + 3)
-#define TROUT_GPIO_SD_DOOR_N (TROUT_GPIO_INT2_BASE + 4)
-#define TROUT_GPIO_CAM_BTN_STEP1_N (TROUT_GPIO_INT2_BASE + 5)
-#define TROUT_GPIO_CAM_BTN_STEP2_N (TROUT_GPIO_INT2_BASE + 6)
-#define TROUT_GPIO_TP_ATT_N (TROUT_GPIO_INT2_BASE + 7)
-#define TROUT_GPIO_BANK0_FIRST_INT_SOURCE (TROUT_GPIO_NAVI_ACT_N)
-#define TROUT_GPIO_BANK0_LAST_INT_SOURCE (TROUT_GPIO_TP_ATT_N)
-
-#define TROUT_GPIO_H2W_DAT_GPI (TROUT_GPIO_MISC1_BASE + 0)
-#define TROUT_GPIO_H2W_CLK_GPI (TROUT_GPIO_MISC1_BASE + 1)
-#define TROUT_GPIO_CPLD128_VER_0 (TROUT_GPIO_MISC1_BASE + 4)
-#define TROUT_GPIO_CPLD128_VER_1 (TROUT_GPIO_MISC1_BASE + 5)
-#define TROUT_GPIO_CPLD128_VER_2 (TROUT_GPIO_MISC1_BASE + 6)
-#define TROUT_GPIO_CPLD128_VER_3 (TROUT_GPIO_MISC1_BASE + 7)
-
-#define TROUT_GPIO_SDMC_CD_N (TROUT_GPIO_VIRTUAL_BASE + 0)
-#define TROUT_GPIO_END (TROUT_GPIO_SDMC_CD_N)
-#define TROUT_GPIO_BANK1_FIRST_INT_SOURCE (TROUT_GPIO_SDMC_CD_N)
-#define TROUT_GPIO_BANK1_LAST_INT_SOURCE (TROUT_GPIO_SDMC_CD_N)
-
-#define TROUT_GPIO_VIRTUAL_TO_REAL_OFFSET \
- (TROUT_GPIO_INT5_BASE - TROUT_GPIO_VIRTUAL_BASE)
-
-#define TROUT_INT_START (NR_MSM_IRQS + NR_GPIO_IRQS)
-#define TROUT_INT_BANK0_COUNT (8)
-#define TROUT_INT_BANK1_START (TROUT_INT_START + TROUT_INT_BANK0_COUNT)
-#define TROUT_INT_BANK1_COUNT (1)
-#define TROUT_INT_END (TROUT_INT_START + TROUT_INT_BANK0_COUNT + \
- TROUT_INT_BANK1_COUNT - 1)
-#define TROUT_GPIO_TO_INT(n) (((n) <= TROUT_GPIO_BANK0_LAST_INT_SOURCE) ? \
- (TROUT_INT_START - TROUT_GPIO_BANK0_FIRST_INT_SOURCE + (n)) : \
- (TROUT_INT_BANK1_START - TROUT_GPIO_BANK1_FIRST_INT_SOURCE + (n)))
-
-#define TROUT_INT_TO_BANK(n) ((n - TROUT_INT_START) / TROUT_INT_BANK0_COUNT)
-#define TROUT_INT_TO_MASK(n) (1U << ((n - TROUT_INT_START) & 7))
-#define TROUT_BANK_TO_MASK_REG(bank) \
- (bank ? TROUT_GPIO_INT_MASK1_REG : TROUT_GPIO_INT_MASK0_REG)
-#define TROUT_BANK_TO_STAT_REG(bank) \
- (bank ? TROUT_GPIO_INT_STAT1_REG : TROUT_GPIO_INT_STAT0_REG)
-
-#endif /* GUARD */
diff --git a/arch/arm/mach-msm/idle.S b/arch/arm/mach-msm/idle.S
index 6a94f05..d8e8027 100644
--- a/arch/arm/mach-msm/idle.S
+++ b/arch/arm/mach-msm/idle.S
@@ -20,17 +20,4 @@
#include <asm/assembler.h>
ENTRY(arch_idle)
-#ifdef CONFIG_MSM7X00A_IDLE
- mrc p15, 0, r1, c1, c0, 0 /* read current CR */
- bic r0, r1, #(1 << 2) /* clear dcache bit */
- bic r0, r0, #(1 << 12) /* clear icache bit */
- mcr p15, 0, r0, c1, c0, 0 /* disable d/i cache */
-
- mov r0, #0 /* prepare wfi value */
- mcr p15, 0, r0, c7, c10, 0 /* flush the cache */
- mcr p15, 0, r0, c7, c10, 4 /* memory barrier */
- mcr p15, 0, r0, c7, c0, 4 /* wait for interrupt */
-
- mcr p15, 0, r1, c1, c0, 0 /* restore d/i cache */
-#endif
mov pc, lr
diff --git a/arch/arm/mach-msm/include/mach/irqs-7x00.h b/arch/arm/mach-msm/include/mach/irqs-7x00.h
deleted file mode 100644
index f1fe706..0000000
--- a/arch/arm/mach-msm/include/mach/irqs-7x00.h
+++ /dev/null
@@ -1,75 +0,0 @@
-/*
- * Copyright (C) 2007 Google, Inc.
- * Copyright (c) 2009, Code Aurora Forum. All rights reserved.
- * Author: Brian Swetland <swetland at google.com>
- */
-
-#ifndef __ASM_ARCH_MSM_IRQS_7X00_H
-#define __ASM_ARCH_MSM_IRQS_7X00_H
-
-/* MSM ARM11 Interrupt Numbers */
-/* See 80-VE113-1 A, pp219-221 */
-
-#define INT_A9_M2A_0 0
-#define INT_A9_M2A_1 1
-#define INT_A9_M2A_2 2
-#define INT_A9_M2A_3 3
-#define INT_A9_M2A_4 4
-#define INT_A9_M2A_5 5
-#define INT_A9_M2A_6 6
-#define INT_GP_TIMER_EXP 7
-#define INT_DEBUG_TIMER_EXP 8
-#define INT_UART1 9
-#define INT_UART2 10
-#define INT_UART3 11
-#define INT_UART1_RX 12
-#define INT_UART2_RX 13
-#define INT_UART3_RX 14
-#define INT_USB_OTG 15
-#define INT_MDDI_PRI 16
-#define INT_MDDI_EXT 17
-#define INT_MDDI_CLIENT 18
-#define INT_MDP 19
-#define INT_GRAPHICS 20
-#define INT_ADM_AARM 21
-#define INT_ADSP_A11 22
-#define INT_ADSP_A9_A11 23
-#define INT_SDC1_0 24
-#define INT_SDC1_1 25
-#define INT_SDC2_0 26
-#define INT_SDC2_1 27
-#define INT_KEYSENSE 28
-#define INT_TCHSCRN_SSBI 29
-#define INT_TCHSCRN1 30
-#define INT_TCHSCRN2 31
-
-#define INT_GPIO_GROUP1 (32 + 0)
-#define INT_GPIO_GROUP2 (32 + 1)
-#define INT_PWB_I2C (32 + 2)
-#define INT_SOFTRESET (32 + 3)
-#define INT_NAND_WR_ER_DONE (32 + 4)
-#define INT_NAND_OP_DONE (32 + 5)
-#define INT_PBUS_ARM11 (32 + 6)
-#define INT_AXI_MPU_SMI (32 + 7)
-#define INT_AXI_MPU_EBI1 (32 + 8)
-#define INT_AD_HSSD (32 + 9)
-#define INT_ARM11_PMU (32 + 10)
-#define INT_ARM11_DMA (32 + 11)
-#define INT_TSIF_IRQ (32 + 12)
-#define INT_UART1DM_IRQ (32 + 13)
-#define INT_UART1DM_RX (32 + 14)
-#define INT_USB_HS (32 + 15)
-#define INT_SDC3_0 (32 + 16)
-#define INT_SDC3_1 (32 + 17)
-#define INT_SDC4_0 (32 + 18)
-#define INT_SDC4_1 (32 + 19)
-#define INT_UART2DM_RX (32 + 20)
-#define INT_UART2DM_IRQ (32 + 21)
-
-/* 22-31 are reserved */
-
-#define NR_MSM_IRQS 64
-#define NR_GPIO_IRQS 122
-#define NR_BOARD_IRQS 64
-
-#endif
diff --git a/arch/arm/mach-msm/include/mach/irqs.h b/arch/arm/mach-msm/include/mach/irqs.h
index 3cd78b1..4bfd614 100644
--- a/arch/arm/mach-msm/include/mach/irqs.h
+++ b/arch/arm/mach-msm/include/mach/irqs.h
@@ -29,8 +29,6 @@
#elif defined(CONFIG_ARCH_MSM8960)
/* TODO: Make these not generic. */
#include "irqs-8960.h"
-#elif defined(CONFIG_ARCH_MSM_ARM11)
-#include "irqs-7x00.h"
#else
#error "Unknown architecture specification"
#endif
diff --git a/arch/arm/mach-msm/include/mach/msm_iomap-7x00.h b/arch/arm/mach-msm/include/mach/msm_iomap-7x00.h
deleted file mode 100644
index 94fe9fe..0000000
--- a/arch/arm/mach-msm/include/mach/msm_iomap-7x00.h
+++ /dev/null
@@ -1,127 +0,0 @@
-/* arch/arm/mach-msm/include/mach/msm_iomap.h
- *
- * Copyright (C) 2007 Google, Inc.
- * Copyright (c) 2011, Code Aurora Forum. All rights reserved.
- * Author: Brian Swetland <swetland at google.com>
- *
- * This software is licensed under the terms of the GNU General Public
- * License version 2, as published by the Free Software Foundation, and
- * may be copied, distributed, and modified under those terms.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- *
- * The MSM peripherals are spread all over across 768MB of physical
- * space, which makes just having a simple IO_ADDRESS macro to slide
- * them into the right virtual location rough. Instead, we will
- * provide a master phys->virt mapping for peripherals here.
- *
- */
-
-#ifndef __ASM_ARCH_MSM_IOMAP_7X00_H
-#define __ASM_ARCH_MSM_IOMAP_7X00_H
-
-#include <asm/sizes.h>
-
-/* Physical base address and size of peripherals.
- * Ordered by the virtual base addresses they will be mapped at.
- *
- * MSM_VIC_BASE must be an value that can be loaded via a "mov"
- * instruction, otherwise entry-macro.S will not compile.
- *
- * If you add or remove entries here, you'll want to edit the
- * msm_io_desc array in arch/arm/mach-msm/io.c to reflect your
- * changes.
- *
- */
-
-#ifdef __ASSEMBLY__
-#define IOMEM(x) x
-#else
-#define IOMEM(x) ((void __force __iomem *)(x))
-#endif
-
-#define MSM_VIC_BASE IOMEM(0xE0000000)
-#define MSM_VIC_PHYS 0xC0000000
-#define MSM_VIC_SIZE SZ_4K
-
-#define MSM7X00_CSR_PHYS 0xC0100000
-#define MSM7X00_CSR_SIZE SZ_4K
-
-#define MSM_DMOV_BASE IOMEM(0xE0002000)
-#define MSM_DMOV_PHYS 0xA9700000
-#define MSM_DMOV_SIZE SZ_4K
-
-#define MSM7X00_GPIO1_PHYS 0xA9200000
-#define MSM7X00_GPIO1_SIZE SZ_4K
-
-#define MSM7X00_GPIO2_PHYS 0xA9300000
-#define MSM7X00_GPIO2_SIZE SZ_4K
-
-#define MSM_CLK_CTL_BASE IOMEM(0xE0005000)
-#define MSM_CLK_CTL_PHYS 0xA8600000
-#define MSM_CLK_CTL_SIZE SZ_4K
-
-#define MSM_SHARED_RAM_BASE IOMEM(0xE0100000)
-#define MSM_SHARED_RAM_PHYS 0x01F00000
-#define MSM_SHARED_RAM_SIZE SZ_1M
-
-#define MSM_UART1_PHYS 0xA9A00000
-#define MSM_UART1_SIZE SZ_4K
-
-#define MSM_UART2_PHYS 0xA9B00000
-#define MSM_UART2_SIZE SZ_4K
-
-#define MSM_UART3_PHYS 0xA9C00000
-#define MSM_UART3_SIZE SZ_4K
-
-#ifdef CONFIG_MSM_DEBUG_UART
-#define MSM_DEBUG_UART_BASE 0xE1000000
-#if CONFIG_MSM_DEBUG_UART == 1
-#define MSM_DEBUG_UART_PHYS MSM_UART1_PHYS
-#elif CONFIG_MSM_DEBUG_UART == 2
-#define MSM_DEBUG_UART_PHYS MSM_UART2_PHYS
-#elif CONFIG_MSM_DEBUG_UART == 3
-#define MSM_DEBUG_UART_PHYS MSM_UART3_PHYS
-#endif
-#define MSM_DEBUG_UART_SIZE SZ_4K
-#endif
-
-#define MSM_SDC1_PHYS 0xA0400000
-#define MSM_SDC1_SIZE SZ_4K
-
-#define MSM_SDC2_PHYS 0xA0500000
-#define MSM_SDC2_SIZE SZ_4K
-
-#define MSM_SDC3_PHYS 0xA0600000
-#define MSM_SDC3_SIZE SZ_4K
-
-#define MSM_SDC4_PHYS 0xA0700000
-#define MSM_SDC4_SIZE SZ_4K
-
-#define MSM_I2C_PHYS 0xA9900000
-#define MSM_I2C_SIZE SZ_4K
-
-#define MSM_HSUSB_PHYS 0xA0800000
-#define MSM_HSUSB_SIZE SZ_4K
-
-#define MSM_PMDH_PHYS 0xAA600000
-#define MSM_PMDH_SIZE SZ_4K
-
-#define MSM_EMDH_PHYS 0xAA700000
-#define MSM_EMDH_SIZE SZ_4K
-
-#define MSM_MDP_PHYS 0xAA200000
-#define MSM_MDP_SIZE 0x000F0000
-
-#define MSM_MDC_PHYS 0xAA500000
-#define MSM_MDC_SIZE SZ_1M
-
-#define MSM_AD5_PHYS 0xAC000000
-#define MSM_AD5_SIZE (SZ_1M*13)
-
-
-#endif
diff --git a/arch/arm/mach-msm/include/mach/msm_iomap.h b/arch/arm/mach-msm/include/mach/msm_iomap.h
index 4ded152..f4027a6 100644
--- a/arch/arm/mach-msm/include/mach/msm_iomap.h
+++ b/arch/arm/mach-msm/include/mach/msm_iomap.h
@@ -49,8 +49,6 @@
#include "msm_iomap-8x50.h"
#elif defined(CONFIG_ARCH_MSM8X60)
#include "msm_iomap-8x60.h"
-#else
-#include "msm_iomap-7x00.h"
#endif
#include "msm_iomap-8960.h"
diff --git a/arch/arm/mach-msm/io.c b/arch/arm/mach-msm/io.c
index 8759ecf..45561d0 100644
--- a/arch/arm/mach-msm/io.c
+++ b/arch/arm/mach-msm/io.c
@@ -38,40 +38,6 @@
#define MSM_DEVICE(name) MSM_CHIP_DEVICE(name, MSM)
-#if defined(CONFIG_ARCH_MSM7X00A) || defined(CONFIG_ARCH_MSM7X27) \
- || defined(CONFIG_ARCH_MSM7X25)
-static struct map_desc msm_io_desc[] __initdata = {
- MSM_DEVICE(VIC),
- MSM_CHIP_DEVICE(CSR, MSM7X00),
- MSM_DEVICE(DMOV),
- MSM_CHIP_DEVICE(GPIO1, MSM7X00),
- MSM_CHIP_DEVICE(GPIO2, MSM7X00),
- MSM_DEVICE(CLK_CTL),
-#ifdef CONFIG_MSM_DEBUG_UART
- MSM_DEVICE(DEBUG_UART),
-#endif
-#ifdef CONFIG_ARCH_MSM7X30
- MSM_DEVICE(GCC),
-#endif
- {
- .virtual = (unsigned long) MSM_SHARED_RAM_BASE,
- .pfn = __phys_to_pfn(MSM_SHARED_RAM_PHYS),
- .length = MSM_SHARED_RAM_SIZE,
- .type = MT_DEVICE,
- },
-};
-
-void __init msm_map_common_io(void)
-{
- /* Make sure the peripheral register window is closed, since
- * we will use PTE flags (TEX[1]=1,B=0,C=1) to determine which
- * pages are peripheral interface or not.
- */
- asm("mcr p15, 0, %0, c15, c2, 4" : : "r" (0));
- iotable_init(msm_io_desc, ARRAY_SIZE(msm_io_desc));
-}
-#endif
-
#ifdef CONFIG_ARCH_QSD8X50
static struct map_desc qsd8x50_io_desc[] __initdata = {
MSM_DEVICE(VIC),
diff --git a/arch/arm/mach-msm/irq.c b/arch/arm/mach-msm/irq.c
deleted file mode 100644
index ea514be..0000000
--- a/arch/arm/mach-msm/irq.c
+++ /dev/null
@@ -1,151 +0,0 @@
-/* linux/arch/arm/mach-msm/irq.c
- *
- * Copyright (C) 2007 Google, Inc.
- *
- * This software is licensed under the terms of the GNU General Public
- * License version 2, as published by the Free Software Foundation, and
- * may be copied, distributed, and modified under those terms.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- */
-
-#include <linux/init.h>
-#include <linux/module.h>
-#include <linux/sched.h>
-#include <linux/interrupt.h>
-#include <linux/ptrace.h>
-#include <linux/timer.h>
-#include <linux/irq.h>
-#include <linux/io.h>
-
-#include <mach/hardware.h>
-
-#include <mach/msm_iomap.h>
-
-#define VIC_REG(off) (MSM_VIC_BASE + (off))
-
-#define VIC_INT_SELECT0 VIC_REG(0x0000) /* 1: FIQ, 0: IRQ */
-#define VIC_INT_SELECT1 VIC_REG(0x0004) /* 1: FIQ, 0: IRQ */
-#define VIC_INT_EN0 VIC_REG(0x0010)
-#define VIC_INT_EN1 VIC_REG(0x0014)
-#define VIC_INT_ENCLEAR0 VIC_REG(0x0020)
-#define VIC_INT_ENCLEAR1 VIC_REG(0x0024)
-#define VIC_INT_ENSET0 VIC_REG(0x0030)
-#define VIC_INT_ENSET1 VIC_REG(0x0034)
-#define VIC_INT_TYPE0 VIC_REG(0x0040) /* 1: EDGE, 0: LEVEL */
-#define VIC_INT_TYPE1 VIC_REG(0x0044) /* 1: EDGE, 0: LEVEL */
-#define VIC_INT_POLARITY0 VIC_REG(0x0050) /* 1: NEG, 0: POS */
-#define VIC_INT_POLARITY1 VIC_REG(0x0054) /* 1: NEG, 0: POS */
-#define VIC_NO_PEND_VAL VIC_REG(0x0060)
-#define VIC_INT_MASTEREN VIC_REG(0x0064) /* 1: IRQ, 2: FIQ */
-#define VIC_PROTECTION VIC_REG(0x006C) /* 1: ENABLE */
-#define VIC_CONFIG VIC_REG(0x0068) /* 1: USE ARM1136 VIC */
-#define VIC_IRQ_STATUS0 VIC_REG(0x0080)
-#define VIC_IRQ_STATUS1 VIC_REG(0x0084)
-#define VIC_FIQ_STATUS0 VIC_REG(0x0090)
-#define VIC_FIQ_STATUS1 VIC_REG(0x0094)
-#define VIC_RAW_STATUS0 VIC_REG(0x00A0)
-#define VIC_RAW_STATUS1 VIC_REG(0x00A4)
-#define VIC_INT_CLEAR0 VIC_REG(0x00B0)
-#define VIC_INT_CLEAR1 VIC_REG(0x00B4)
-#define VIC_SOFTINT0 VIC_REG(0x00C0)
-#define VIC_SOFTINT1 VIC_REG(0x00C4)
-#define VIC_IRQ_VEC_RD VIC_REG(0x00D0) /* pending int # */
-#define VIC_IRQ_VEC_PEND_RD VIC_REG(0x00D4) /* pending vector addr */
-#define VIC_IRQ_VEC_WR VIC_REG(0x00D8)
-#define VIC_IRQ_IN_SERVICE VIC_REG(0x00E0)
-#define VIC_IRQ_IN_STACK VIC_REG(0x00E4)
-#define VIC_TEST_BUS_SEL VIC_REG(0x00E8)
-
-#define VIC_VECTPRIORITY(n) VIC_REG(0x0200+((n) * 4))
-#define VIC_VECTADDR(n) VIC_REG(0x0400+((n) * 4))
-
-static void msm_irq_ack(struct irq_data *d)
-{
- void __iomem *reg = VIC_INT_CLEAR0 + ((d->irq & 32) ? 4 : 0);
- writel(1 << (d->irq & 31), reg);
-}
-
-static void msm_irq_mask(struct irq_data *d)
-{
- void __iomem *reg = VIC_INT_ENCLEAR0 + ((d->irq & 32) ? 4 : 0);
- writel(1 << (d->irq & 31), reg);
-}
-
-static void msm_irq_unmask(struct irq_data *d)
-{
- void __iomem *reg = VIC_INT_ENSET0 + ((d->irq & 32) ? 4 : 0);
- writel(1 << (d->irq & 31), reg);
-}
-
-static int msm_irq_set_wake(struct irq_data *d, unsigned int on)
-{
- return -EINVAL;
-}
-
-static int msm_irq_set_type(struct irq_data *d, unsigned int flow_type)
-{
- void __iomem *treg = VIC_INT_TYPE0 + ((d->irq & 32) ? 4 : 0);
- void __iomem *preg = VIC_INT_POLARITY0 + ((d->irq & 32) ? 4 : 0);
- int b = 1 << (d->irq & 31);
-
- if (flow_type & (IRQF_TRIGGER_FALLING | IRQF_TRIGGER_LOW))
- writel(readl(preg) | b, preg);
- if (flow_type & (IRQF_TRIGGER_RISING | IRQF_TRIGGER_HIGH))
- writel(readl(preg) & (~b), preg);
-
- if (flow_type & (IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING)) {
- writel(readl(treg) | b, treg);
- __irq_set_handler_locked(d->irq, handle_edge_irq);
- }
- if (flow_type & (IRQF_TRIGGER_HIGH | IRQF_TRIGGER_LOW)) {
- writel(readl(treg) & (~b), treg);
- __irq_set_handler_locked(d->irq, handle_level_irq);
- }
- return 0;
-}
-
-static struct irq_chip msm_irq_chip = {
- .name = "msm",
- .irq_ack = msm_irq_ack,
- .irq_mask = msm_irq_mask,
- .irq_unmask = msm_irq_unmask,
- .irq_set_wake = msm_irq_set_wake,
- .irq_set_type = msm_irq_set_type,
-};
-
-void __init msm_init_irq(void)
-{
- unsigned n;
-
- /* select level interrupts */
- writel(0, VIC_INT_TYPE0);
- writel(0, VIC_INT_TYPE1);
-
- /* select highlevel interrupts */
- writel(0, VIC_INT_POLARITY0);
- writel(0, VIC_INT_POLARITY1);
-
- /* select IRQ for all INTs */
- writel(0, VIC_INT_SELECT0);
- writel(0, VIC_INT_SELECT1);
-
- /* disable all INTs */
- writel(0, VIC_INT_EN0);
- writel(0, VIC_INT_EN1);
-
- /* don't use 1136 vic */
- writel(0, VIC_CONFIG);
-
- /* enable interrupt controller */
- writel(1, VIC_INT_MASTEREN);
-
- for (n = 0; n < NR_MSM_IRQS; n++) {
- irq_set_chip_and_handler(n, &msm_irq_chip, handle_level_irq);
- set_irq_flags(n, IRQF_VALID);
- }
-}
diff --git a/arch/arm/mach-msm/smd_private.h b/arch/arm/mach-msm/smd_private.h
index 727bfe6..e66d9fa 100644
--- a/arch/arm/mach-msm/smd_private.h
+++ b/arch/arm/mach-msm/smd_private.h
@@ -64,13 +64,6 @@ struct smem_shared {
#define SMSM_V1_SIZE (sizeof(unsigned) * 8)
#define SMSM_V2_SIZE (sizeof(unsigned) * 4)
-#ifdef CONFIG_MSM_SMD_PKG3
-struct smsm_interrupt_info {
- uint32_t interrupt_mask;
- uint32_t pending_interrupts;
- uint32_t wakeup_reason;
-};
-#else
#define DEM_MAX_PORT_NAME_LEN (20)
struct msm_dem_slave_data {
uint32_t sleep_time;
@@ -85,7 +78,6 @@ struct msm_dem_slave_data {
char smd_port_name[DEM_MAX_PORT_NAME_LEN];
uint32_t reserved2;
};
-#endif
#define SZ_DIAG_ERR_MSG 0xC8
#define ID_DIAG_ERR_MSG SMEM_DIAG_ERR_MESSAGE
@@ -126,13 +118,6 @@ struct msm_dem_slave_data {
#define SMSM_WKUP_REASON_ALARM 0x00000010
#define SMSM_WKUP_REASON_RESET 0x00000020
-#ifdef CONFIG_ARCH_MSM7X00A
-enum smsm_state_item {
- SMSM_STATE_APPS = 1,
- SMSM_STATE_MODEM = 3,
- SMSM_STATE_COUNT,
-};
-#else
enum smsm_state_item {
SMSM_STATE_APPS,
SMSM_STATE_MODEM,
@@ -144,7 +129,6 @@ enum smsm_state_item {
SMSM_STATE_TIME_MASTER_DEM,
SMSM_STATE_COUNT,
};
-#endif
void *smem_alloc(unsigned id, unsigned size);
int smsm_change_state(enum smsm_state_item item, uint32_t clear_mask, uint32_t set_mask);
@@ -335,28 +319,6 @@ uint32_t raw_smsm_get_state(enum smsm_state_item item);
extern void msm_init_last_radio_log(struct module *);
-#ifdef CONFIG_MSM_SMD_PKG3
-/*
- * This allocator assumes an SMD Package v3 which only exists on
- * MSM7x00 SoC's.
- */
-static inline int _smd_alloc_channel(struct smd_channel *ch)
-{
- struct smd_shared_v1 *shared1;
-
- shared1 = smem_alloc(ID_SMD_CHANNELS + ch->n, sizeof(*shared1));
- if (!shared1) {
- pr_err("smd_alloc_channel() cid %d does not exist\n", ch->n);
- return -1;
- }
- ch->send = &shared1->ch0;
- ch->recv = &shared1->ch1;
- ch->send_data = shared1->data0;
- ch->recv_data = shared1->data1;
- ch->fifo_size = SMD_BUF_SIZE;
- return 0;
-}
-#else
/*
* This allocator assumes an SMD Package v4, the most common
* and the default.
@@ -385,7 +347,6 @@ static inline int _smd_alloc_channel(struct smd_channel *ch)
ch->fifo_size = buffer_sz;
return 0;
}
-#endif /* CONFIG_MSM_SMD_PKG3 */
#if defined(CONFIG_ARCH_MSM7X30)
static inline void msm_a2m_int(uint32_t irq)
diff --git a/arch/arm/mach-msm/timer.c b/arch/arm/mach-msm/timer.c
index afeeca5..04770f3 100644
--- a/arch/arm/mach-msm/timer.c
+++ b/arch/arm/mach-msm/timer.c
@@ -203,10 +203,7 @@ static void __init msm_timer_init(void)
int res;
int global_offset = 0;
- if (cpu_is_msm7x01()) {
- msm_clocks[MSM_CLOCK_GPT].regbase = MSM_CSR_BASE;
- msm_clocks[MSM_CLOCK_DGT].regbase = MSM_CSR_BASE + 0x10;
- } else if (cpu_is_msm7x30()) {
+ if (cpu_is_msm7x30()) {
msm_clocks[MSM_CLOCK_GPT].regbase = MSM_CSR_BASE + 0x04;
msm_clocks[MSM_CLOCK_DGT].regbase = MSM_CSR_BASE + 0x24;
} else if (cpu_is_qsd8x50()) {
--
Sent by an employee of the Qualcomm Innovation Center, Inc.
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum.
More information about the linux-arm-kernel
mailing list