[PATCH v3 3/3] arm: omap3: cm-t35: add support for cm-t3730
Igor Grinberg
grinberg at compulab.co.il
Tue Jun 14 17:16:14 EDT 2011
cm-t3730 is basically the same board as cm-t35,
but has AM/DM3730 SoC assembled and therefore some changes are required.
Signed-off-by: Igor Grinberg <grinberg at compulab.co.il>
Acked-by: Mike Rapoport <mike at compulab.co.il>
---
v3: fix MACH_* selection
remove completely the use of cpu_is_*
v2: Add debug uart entry
arch/arm/mach-omap2/Kconfig | 6 ++-
arch/arm/mach-omap2/board-cm-t35.c | 77 ++++++++++++++++++++-----
arch/arm/plat-omap/include/plat/uncompress.h | 1 +
3 files changed, 67 insertions(+), 17 deletions(-)
diff --git a/arch/arm/mach-omap2/Kconfig b/arch/arm/mach-omap2/Kconfig
index 19d5891..4ae6257 100644
--- a/arch/arm/mach-omap2/Kconfig
+++ b/arch/arm/mach-omap2/Kconfig
@@ -266,9 +266,10 @@ config MACH_OMAP_ZOOM3
select REGULATOR_FIXED_VOLTAGE
config MACH_CM_T35
- bool "CompuLab CM-T35 module"
+ bool "CompuLab CM-T35/CM-T3730 modules"
depends on ARCH_OMAP3
default y
+ select MACH_CM_T3730
select OMAP_PACKAGE_CUS
config MACH_CM_T3517
@@ -277,6 +278,9 @@ config MACH_CM_T3517
default y
select OMAP_PACKAGE_CBB
+config MACH_CM_T3730
+ bool
+
config MACH_IGEP0020
bool "IGEP v2 board"
depends on ARCH_OMAP3
diff --git a/arch/arm/mach-omap2/board-cm-t35.c b/arch/arm/mach-omap2/board-cm-t35.c
index 256b81c..ea31281 100644
--- a/arch/arm/mach-omap2/board-cm-t35.c
+++ b/arch/arm/mach-omap2/board-cm-t35.c
@@ -1,5 +1,5 @@
/*
- * board-cm-t35.c (CompuLab CM-T35 module)
+ * CompuLab CM-T35/CM-T3730 modules support
*
* Copyright (C) 2009-2011 CompuLab, Ltd.
* Authors: Mike Rapoport <mike at compulab.co.il>
@@ -574,17 +574,11 @@ static struct omap_board_mux board_mux[] __initdata = {
OMAP3_MUX(UART1_TX, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
OMAP3_MUX(UART1_RX, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
- /* DSS */
+ /* common DSS */
OMAP3_MUX(DSS_PCLK, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
OMAP3_MUX(DSS_HSYNC, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
OMAP3_MUX(DSS_VSYNC, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
OMAP3_MUX(DSS_ACBIAS, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_DATA0, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_DATA1, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_DATA2, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_DATA3, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_DATA4, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_DATA5, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
OMAP3_MUX(DSS_DATA6, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
OMAP3_MUX(DSS_DATA7, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
OMAP3_MUX(DSS_DATA8, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
@@ -597,12 +591,6 @@ static struct omap_board_mux board_mux[] __initdata = {
OMAP3_MUX(DSS_DATA15, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
OMAP3_MUX(DSS_DATA16, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
OMAP3_MUX(DSS_DATA17, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_DATA18, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_DATA19, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_DATA20, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_DATA21, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_DATA22, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_DATA23, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
/* display controls */
OMAP3_MUX(MCBSP1_FSR, OMAP_MUX_MODE4 | OMAP_PIN_OUTPUT),
@@ -615,19 +603,53 @@ static struct omap_board_mux board_mux[] __initdata = {
{ .reg_offset = OMAP_MUX_TERMINATOR },
};
+
+static void __init cm_t3x_common_dss_mux_init(int mux_mode)
+{
+ omap_mux_init_signal("dss_data18", mux_mode);
+ omap_mux_init_signal("dss_data19", mux_mode);
+ omap_mux_init_signal("dss_data20", mux_mode);
+ omap_mux_init_signal("dss_data21", mux_mode);
+ omap_mux_init_signal("dss_data22", mux_mode);
+ omap_mux_init_signal("dss_data23", mux_mode);
+}
+
+static void __init cm_t35_init_mux(void)
+{
+ omap_mux_init_signal("gpio_70", OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT);
+ omap_mux_init_signal("gpio_71", OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT);
+ omap_mux_init_signal("gpio_72", OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT);
+ omap_mux_init_signal("gpio_73", OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT);
+ omap_mux_init_signal("gpio_74", OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT);
+ omap_mux_init_signal("gpio_75", OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT);
+ cm_t3x_common_dss_mux_init(OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT);
+}
+
+static void __init cm_t3730_init_mux(void)
+{
+ omap_mux_init_signal("sys_boot0", OMAP_MUX_MODE3 | OMAP_PIN_OUTPUT);
+ omap_mux_init_signal("sys_boot1", OMAP_MUX_MODE3 | OMAP_PIN_OUTPUT);
+ omap_mux_init_signal("sys_boot3", OMAP_MUX_MODE3 | OMAP_PIN_OUTPUT);
+ omap_mux_init_signal("sys_boot4", OMAP_MUX_MODE3 | OMAP_PIN_OUTPUT);
+ omap_mux_init_signal("sys_boot5", OMAP_MUX_MODE3 | OMAP_PIN_OUTPUT);
+ omap_mux_init_signal("sys_boot6", OMAP_MUX_MODE3 | OMAP_PIN_OUTPUT);
+ cm_t3x_common_dss_mux_init(OMAP_MUX_MODE3 | OMAP_PIN_OUTPUT);
+}
+#else
+static inline void cm_t35_init_mux(void) {}
+static inline void cm_t3730_init_mux(void) {}
#endif
static struct omap_board_config_kernel cm_t35_config[] __initdata = {
};
-static void __init cm_t35_init(void)
+static void __init cm_t3x_common_init(void)
{
omap_board_config = cm_t35_config;
omap_board_config_size = ARRAY_SIZE(cm_t35_config);
omap3_mux_init(board_mux, OMAP_PACKAGE_CUS);
omap_serial_init();
cm_t35_init_i2c();
- cm_t35_init_nand();
omap_ads7846_init(1, CM_T35_GPIO_PENDOWN, 0, NULL);
cm_t35_init_ethernet();
cm_t35_init_led();
@@ -637,6 +659,19 @@ static void __init cm_t35_init(void)
usbhs_init(&usbhs_bdata);
}
+static void __init cm_t35_init(void)
+{
+ cm_t3x_common_init();
+ cm_t35_init_mux();
+ cm_t35_init_nand();
+}
+
+static void __init cm_t3730_init(void)
+{
+ cm_t3x_common_init();
+ cm_t3730_init_mux();
+}
+
MACHINE_START(CM_T35, "Compulab CM-T35")
.boot_params = 0x80000100,
.reserve = omap_reserve,
@@ -646,3 +681,13 @@ MACHINE_START(CM_T35, "Compulab CM-T35")
.init_machine = cm_t35_init,
.timer = &omap_timer,
MACHINE_END
+
+MACHINE_START(CM_T3730, "Compulab CM-T3730")
+ .boot_params = 0x80000100,
+ .reserve = omap_reserve,
+ .map_io = omap3_map_io,
+ .init_early = cm_t35_init_early,
+ .init_irq = omap_init_irq,
+ .init_machine = cm_t3730_init,
+ .timer = &omap_timer,
+MACHINE_END
diff --git a/arch/arm/plat-omap/include/plat/uncompress.h b/arch/arm/plat-omap/include/plat/uncompress.h
index ac4b60d..a067484 100644
--- a/arch/arm/plat-omap/include/plat/uncompress.h
+++ b/arch/arm/plat-omap/include/plat/uncompress.h
@@ -148,6 +148,7 @@ static inline void __arch_decomp_setup(unsigned long arch_id)
/* omap3 based boards using UART3 */
DEBUG_LL_OMAP3(3, cm_t35);
DEBUG_LL_OMAP3(3, cm_t3517);
+ DEBUG_LL_OMAP3(3, cm_t3730);
DEBUG_LL_OMAP3(3, craneboard);
DEBUG_LL_OMAP3(3, devkit8000);
DEBUG_LL_OMAP3(3, igep0020);
--
1.7.3.4
More information about the linux-arm-kernel
mailing list