[PATCH 2/2] gpio/u300: rewrite gpio driver
Linus Walleij
linus.walleij at stericsson.com
Fri Jun 10 04:49:20 EDT 2011
From: Linus Walleij <linus.walleij at linaro.org>
This rewrites the U300 GPIO driver using gpiolib and the irq_chip
abstractions, makes it runtime-configured rather than compile-time,
Includes a resource size off-by-one fix from Joe Perches from the
trivial tree.
Cc: Jonas Aaberg <jonas.aberg at stericsson.com>
Reported-by: Joe Perches <joe at perches.com>
Acked-by: Arnd Bergmann <arnd at arndb.de>
Signed-off-by: Linus Walleij <linus.walleij at linaro.org>
---
arch/arm/Kconfig | 2 +-
arch/arm/mach-u300/Kconfig | 1 +
arch/arm/mach-u300/core.c | 31 +-
arch/arm/mach-u300/include/mach/gpio.h | 163 +-----
arch/arm/mach-u300/include/mach/irqs.h | 25 +-
drivers/gpio/Kconfig | 9 +
drivers/gpio/gpio-u300.c | 1176 +++++++++++++++++++-------------
include/linux/gpio/u300.h | 82 +++
8 files changed, 831 insertions(+), 658 deletions(-)
create mode 100644 include/linux/gpio/u300.h
diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
index 9adc278..e0074af 100644
--- a/arch/arm/Kconfig
+++ b/arch/arm/Kconfig
@@ -808,7 +808,7 @@ config ARCH_U300
select ARM_VIC
select GENERIC_CLOCKEVENTS
select CLKDEV_LOOKUP
- select GENERIC_GPIO
+ select ARCH_REQUIRE_GPIOLIB
help
Support for ST-Ericsson U300 series mobile platforms.
diff --git a/arch/arm/mach-u300/Kconfig b/arch/arm/mach-u300/Kconfig
index 32a7b0f..7b5c229 100644
--- a/arch/arm/mach-u300/Kconfig
+++ b/arch/arm/mach-u300/Kconfig
@@ -6,6 +6,7 @@ comment "ST-Ericsson Mobile Platform Products"
config MACH_U300
bool "U300"
+ select GPIO_U300
comment "ST-Ericsson U300/U330/U335/U365 Feature Selections"
diff --git a/arch/arm/mach-u300/core.c b/arch/arm/mach-u300/core.c
index 513d6ab..ddb604c 100644
--- a/arch/arm/mach-u300/core.c
+++ b/arch/arm/mach-u300/core.c
@@ -25,6 +25,7 @@
#include <linux/err.h>
#include <linux/mtd/nand.h>
#include <linux/mtd/fsmc.h>
+#include <linux/gpio/u300.h>
#include <asm/types.h>
#include <asm/setup.h>
@@ -239,7 +240,7 @@ static struct resource gpio_resources[] = {
.end = IRQ_U300_GPIO_PORT2,
.flags = IORESOURCE_IRQ,
},
-#ifdef U300_COH901571_3
+#if defined(CONFIG_MACH_U300_BS365) || defined(CONFIG_MACH_U300_BS335)
{
.name = "gpio3",
.start = IRQ_U300_GPIO_PORT3,
@@ -252,6 +253,7 @@ static struct resource gpio_resources[] = {
.end = IRQ_U300_GPIO_PORT4,
.flags = IORESOURCE_IRQ,
},
+#endif
#ifdef CONFIG_MACH_U300_BS335
{
.name = "gpio5",
@@ -266,7 +268,6 @@ static struct resource gpio_resources[] = {
.flags = IORESOURCE_IRQ,
},
#endif /* CONFIG_MACH_U300_BS335 */
-#endif /* U300_COH901571_3 */
};
static struct resource keypad_resources[] = {
@@ -1556,11 +1557,35 @@ static struct platform_device i2c1_device = {
.resource = i2c1_resources,
};
+/*
+ * The different variants have a few different versions of the
+ * GPIO block, with different number of ports.
+ */
+static struct u300_gpio_platform u300_gpio_plat = {
+#if defined(CONFIG_MACH_U300_BS2X) || defined(CONFIG_MACH_U300_BS330)
+ .variant = U300_GPIO_COH901335,
+ .ports = 3,
+#endif
+#ifdef CONFIG_MACH_U300_BS335
+ .variant = U300_GPIO_COH901571_3_BS335,
+ .ports = 7,
+#endif
+#ifdef CONFIG_MACH_U300_BS365
+ .variant = U300_GPIO_COH901571_3_BS365,
+ .ports = 5,
+#endif
+ .gpio_base = 0,
+ .gpio_irq_base = IRQ_U300_GPIO_BASE,
+};
+
static struct platform_device gpio_device = {
.name = "u300-gpio",
.id = -1,
.num_resources = ARRAY_SIZE(gpio_resources),
.resource = gpio_resources,
+ .dev = {
+ .platform_data = &u300_gpio_plat,
+ },
};
static struct platform_device keypad_device = {
@@ -1666,7 +1691,7 @@ void __init u300_init_irq(void)
BUG_ON(IS_ERR(clk));
clk_enable(clk);
- for (i = 0; i < NR_IRQS; i++)
+ for (i = 0; i < U300_VIC_IRQS_END; i++)
set_bit(i, (unsigned long *) &mask[0]);
vic_init((void __iomem *) U300_INTCON0_VBASE, 0, mask[0], mask[0]);
vic_init((void __iomem *) U300_INTCON1_VBASE, 32, mask[1], mask[1]);
diff --git a/arch/arm/mach-u300/include/mach/gpio.h b/arch/arm/mach-u300/include/mach/gpio.h
index d5a71ab..6fc3205 100644
--- a/arch/arm/mach-u300/include/mach/gpio.h
+++ b/arch/arm/mach-u300/include/mach/gpio.h
@@ -17,127 +17,13 @@
#include <linux/io.h>
#include <mach/hardware.h>
#include <asm/irq.h>
+#include <asm-generic/gpio.h>
-/* Switch type depending on platform/chip variant */
-#if defined(CONFIG_MACH_U300_BS2X) || defined(CONFIG_MACH_U300_BS330)
-#define U300_COH901335
-#endif
-#if defined(CONFIG_MACH_U300_BS365) || defined(CONFIG_MACH_U300_BS335)
-#define U300_COH901571_3
-#endif
-
-/* Get base address for regs here */
-#include "u300-regs.h"
-/* IRQ numbers */
-#include "irqs.h"
-
-/*
- * This is the GPIO block definitions. GPIO (General Purpose I/O) can be
- * used for anything, and often is. The event/enable etc figures are for
- * the lowermost pin (pin 0 on each port), shift this left to match your
- * pin if you're gonna use these values.
- */
-#ifdef U300_COH901335
-#define U300_GPIO_PORTX_SPACING (0x1C)
-/* Port X Pin Data Register 32bit, this is both input and output (R/W) */
-#define U300_GPIO_PXPDIR (0x00)
-#define U300_GPIO_PXPDOR (0x00)
-/* Port X Pin Config Register 32bit (R/W) */
-#define U300_GPIO_PXPCR (0x04)
-#define U300_GPIO_PXPCR_ALL_PINS_MODE_MASK (0x0000FFFFUL)
-#define U300_GPIO_PXPCR_PIN_MODE_MASK (0x00000003UL)
-#define U300_GPIO_PXPCR_PIN_MODE_SHIFT (0x00000002UL)
-#define U300_GPIO_PXPCR_PIN_MODE_INPUT (0x00000000UL)
-#define U300_GPIO_PXPCR_PIN_MODE_OUTPUT_PUSH_PULL (0x00000001UL)
-#define U300_GPIO_PXPCR_PIN_MODE_OUTPUT_OPEN_DRAIN (0x00000002UL)
-#define U300_GPIO_PXPCR_PIN_MODE_OUTPUT_OPEN_SOURCE (0x00000003UL)
-/* Port X Interrupt Event Register 32bit (R/W) */
-#define U300_GPIO_PXIEV (0x08)
-#define U300_GPIO_PXIEV_ALL_IRQ_EVENT_MASK (0x000000FFUL)
-#define U300_GPIO_PXIEV_IRQ_EVENT (0x00000001UL)
-/* Port X Interrupt Enable Register 32bit (R/W) */
-#define U300_GPIO_PXIEN (0x0C)
-#define U300_GPIO_PXIEN_ALL_IRQ_ENABLE_MASK (0x000000FFUL)
-#define U300_GPIO_PXIEN_IRQ_ENABLE (0x00000001UL)
-/* Port X Interrupt Force Register 32bit (R/W) */
-#define U300_GPIO_PXIFR (0x10)
-#define U300_GPIO_PXIFR_ALL_IRQ_FORCE_MASK (0x000000FFUL)
-#define U300_GPIO_PXIFR_IRQ_FORCE (0x00000001UL)
-/* Port X Interrupt Config Register 32bit (R/W) */
-#define U300_GPIO_PXICR (0x14)
-#define U300_GPIO_PXICR_ALL_IRQ_CONFIG_MASK (0x000000FFUL)
-#define U300_GPIO_PXICR_IRQ_CONFIG_MASK (0x00000001UL)
-#define U300_GPIO_PXICR_IRQ_CONFIG_FALLING_EDGE (0x00000000UL)
-#define U300_GPIO_PXICR_IRQ_CONFIG_RISING_EDGE (0x00000001UL)
-/* Port X Pull-up Enable Register 32bit (R/W) */
-#define U300_GPIO_PXPER (0x18)
-#define U300_GPIO_PXPER_ALL_PULL_UP_DISABLE_MASK (0x000000FFUL)
-#define U300_GPIO_PXPER_PULL_UP_DISABLE (0x00000001UL)
-/* Control Register 32bit (R/W) */
-#define U300_GPIO_CR (0x54)
-#define U300_GPIO_CR_BLOCK_CLOCK_ENABLE (0x00000001UL)
-/* three ports of 8 bits each = GPIO pins 0..23 */
-#define U300_GPIO_NUM_PORTS 3
-#define U300_GPIO_PINS_PER_PORT 8
-#define U300_GPIO_MAX (U300_GPIO_PINS_PER_PORT * U300_GPIO_NUM_PORTS - 1)
-#endif
-
-#ifdef U300_COH901571_3
-/*
- * Control Register 32bit (R/W)
- * bit 15-9 (mask 0x0000FE00) contains the number of cores. 8*cores
- * gives the number of GPIO pins.
- * bit 8-2 (mask 0x000001FC) contains the core version ID.
- */
-#define U300_GPIO_CR (0x00)
-#define U300_GPIO_CR_SYNC_SEL_ENABLE (0x00000002UL)
-#define U300_GPIO_CR_BLOCK_CLKRQ_ENABLE (0x00000001UL)
-#define U300_GPIO_PORTX_SPACING (0x30)
-/* Port X Pin Data INPUT Register 32bit (R/W) */
-#define U300_GPIO_PXPDIR (0x04)
-/* Port X Pin Data OUTPUT Register 32bit (R/W) */
-#define U300_GPIO_PXPDOR (0x08)
-/* Port X Pin Config Register 32bit (R/W) */
-#define U300_GPIO_PXPCR (0x0C)
-#define U300_GPIO_PXPCR_ALL_PINS_MODE_MASK (0x0000FFFFUL)
-#define U300_GPIO_PXPCR_PIN_MODE_MASK (0x00000003UL)
-#define U300_GPIO_PXPCR_PIN_MODE_SHIFT (0x00000002UL)
-#define U300_GPIO_PXPCR_PIN_MODE_INPUT (0x00000000UL)
-#define U300_GPIO_PXPCR_PIN_MODE_OUTPUT_PUSH_PULL (0x00000001UL)
-#define U300_GPIO_PXPCR_PIN_MODE_OUTPUT_OPEN_DRAIN (0x00000002UL)
-#define U300_GPIO_PXPCR_PIN_MODE_OUTPUT_OPEN_SOURCE (0x00000003UL)
-/* Port X Pull-up Enable Register 32bit (R/W) */
-#define U300_GPIO_PXPER (0x10)
-#define U300_GPIO_PXPER_ALL_PULL_UP_DISABLE_MASK (0x000000FFUL)
-#define U300_GPIO_PXPER_PULL_UP_DISABLE (0x00000001UL)
-/* Port X Interrupt Event Register 32bit (R/W) */
-#define U300_GPIO_PXIEV (0x14)
-#define U300_GPIO_PXIEV_ALL_IRQ_EVENT_MASK (0x000000FFUL)
-#define U300_GPIO_PXIEV_IRQ_EVENT (0x00000001UL)
-/* Port X Interrupt Enable Register 32bit (R/W) */
-#define U300_GPIO_PXIEN (0x18)
-#define U300_GPIO_PXIEN_ALL_IRQ_ENABLE_MASK (0x000000FFUL)
-#define U300_GPIO_PXIEN_IRQ_ENABLE (0x00000001UL)
-/* Port X Interrupt Force Register 32bit (R/W) */
-#define U300_GPIO_PXIFR (0x1C)
-#define U300_GPIO_PXIFR_ALL_IRQ_FORCE_MASK (0x000000FFUL)
-#define U300_GPIO_PXIFR_IRQ_FORCE (0x00000001UL)
-/* Port X Interrupt Config Register 32bit (R/W) */
-#define U300_GPIO_PXICR (0x20)
-#define U300_GPIO_PXICR_ALL_IRQ_CONFIG_MASK (0x000000FFUL)
-#define U300_GPIO_PXICR_IRQ_CONFIG_MASK (0x00000001UL)
-#define U300_GPIO_PXICR_IRQ_CONFIG_FALLING_EDGE (0x00000000UL)
-#define U300_GPIO_PXICR_IRQ_CONFIG_RISING_EDGE (0x00000001UL)
-#ifdef CONFIG_MACH_U300_BS335
-/* seven ports of 8 bits each = GPIO pins 0..55 */
-#define U300_GPIO_NUM_PORTS 7
-#else
-/* five ports of 8 bits each = GPIO pins 0..39 */
-#define U300_GPIO_NUM_PORTS 5
-#endif
-#define U300_GPIO_PINS_PER_PORT 8
-#define U300_GPIO_MAX (U300_GPIO_PINS_PER_PORT * U300_GPIO_NUM_PORTS - 1)
-#endif
+/* Map these overrides to gpiolib functions, simply */
+#define gpio_get_value __gpio_get_value
+#define gpio_set_value __gpio_set_value
+#define gpio_cansleep __gpio_cansleep
+#define gpio_to_irq __gpio_to_irq
/*
* Individual pin assignments for the B26/S26. Notice that the
@@ -254,41 +140,4 @@
#endif
-/* translates a pin number to a port number */
-#define PIN_TO_PORT(val) (val >> 3)
-
-/* These can be found in arch/arm/mach-u300/gpio.c */
-extern int gpio_is_valid(int number);
-extern int gpio_request(unsigned gpio, const char *label);
-extern void gpio_free(unsigned gpio);
-extern int gpio_direction_input(unsigned gpio);
-extern int gpio_direction_output(unsigned gpio, int value);
-extern int gpio_register_callback(unsigned gpio,
- int (*func)(void *arg),
- void *);
-extern int gpio_unregister_callback(unsigned gpio);
-extern void enable_irq_on_gpio_pin(unsigned gpio, int edge);
-extern void disable_irq_on_gpio_pin(unsigned gpio);
-extern void gpio_pullup(unsigned gpio, int value);
-extern int gpio_get_value(unsigned gpio);
-extern void gpio_set_value(unsigned gpio, int value);
-
-#define gpio_get_value_cansleep gpio_get_value
-#define gpio_set_value_cansleep gpio_set_value
-
-/* wrappers to sleep-enable the previous two functions */
-static inline unsigned gpio_to_irq(unsigned gpio)
-{
- return PIN_TO_PORT(gpio) + IRQ_U300_GPIO_PORT0;
-}
-
-static inline unsigned irq_to_gpio(unsigned irq)
-{
- /*
- * FIXME: This is no 1-1 mapping at all, it points to the
- * whole block of 8 pins.
- */
- return (irq - IRQ_U300_GPIO_PORT0) << 3;
-}
-
#endif
diff --git a/arch/arm/mach-u300/include/mach/irqs.h b/arch/arm/mach-u300/include/mach/irqs.h
index 09b1b28..d270fea 100644
--- a/arch/arm/mach-u300/include/mach/irqs.h
+++ b/arch/arm/mach-u300/include/mach/irqs.h
@@ -72,7 +72,7 @@
/* DB3150 and DB3200 have only 45 IRQs */
#if defined(CONFIG_MACH_U300_BS2X) || defined(CONFIG_MACH_U300_BS330)
-#define U300_NR_IRQS 45
+#define U300_VIC_IRQS_END 45
#endif
/* The DB3350-specific interrupt lines */
@@ -88,7 +88,7 @@
#define IRQ_U300_GPIO_PORT4 53
#define IRQ_U300_GPIO_PORT5 54
#define IRQ_U300_GPIO_PORT6 55
-#define U300_NR_IRQS 56
+#define U300_VIC_IRQS_END 56
#endif
/* The DB3210-specific interrupt lines */
@@ -106,16 +106,25 @@
#define IRQ_U300_NFIF 45
#define IRQ_U300_NFIF2 46
#define IRQ_U300_SYSCON_PLL_LOCK 47
-#define U300_NR_IRQS 48
+#define U300_VIC_IRQS_END 48
#endif
-#ifdef CONFIG_AB3550_CORE
-#define IRQ_AB3550_BASE (U300_NR_IRQS)
-#define IRQ_AB3550_END (IRQ_AB3550_BASE + 37)
+/* Maximum 8*7 GPIO lines */
+#ifdef CONFIG_GPIO_U300
+#define IRQ_U300_GPIO_BASE (U300_VIC_IRQS_END)
+#define IRQ_U300_GPIO_END (IRQ_U300_GPIO_BASE + 56)
+#else
+#define IRQ_U300_GPIO_END (U300_VIC_IRQS_END)
+#endif
-#define NR_IRQS (IRQ_AB3550_END + 1)
+/* Optional AB3550 mixsig chip */
+#ifdef CONFIG_AB3550_CORE
+#define IRQ_AB3550_BASE (IRQ_U300_GPIO_END)
+#define IRQ_AB3550_END (IRQ_AB3550_BASE + 38)
#else
-#define NR_IRQS U300_NR_IRQS
+#define IRQ_AB3550_END (IRQ_U300_GPIO_END)
#endif
+#define NR_IRQS (IRQ_AB3550_END)
+
#endif
diff --git a/drivers/gpio/Kconfig b/drivers/gpio/Kconfig
index 4a7f631..a12398c 100644
--- a/drivers/gpio/Kconfig
+++ b/drivers/gpio/Kconfig
@@ -152,6 +152,15 @@ config GPIO_SCH
This driver can also be built as a module. If so, the module
will be called sch-gpio.
+config GPIO_U300
+ bool "ST-Ericsson U300 COH 901 335/571 GPIO"
+ depends on GPIOLIB && ARCH_U300
+ help
+ Say yes here to support GPIO interface on ST-Ericsson U300.
+ The names of the two IP block variants supported are
+ COH 901 335 and COH 901 571/3. They contain 3, 5 or 7
+ ports of 8 GPIO pins each.
+
config GPIO_VX855
tristate "VIA VX855/VX875 GPIO"
depends on MFD_SUPPORT && PCI
diff --git a/drivers/gpio/gpio-u300.c b/drivers/gpio/gpio-u300.c
index d927901..3c807d2 100644
--- a/drivers/gpio/gpio-u300.c
+++ b/drivers/gpio/gpio-u300.c
@@ -1,21 +1,16 @@
/*
- *
- * arch/arm/mach-u300/gpio.c
- *
- *
- * Copyright (C) 2007-2009 ST-Ericsson AB
+ * Copyright (C) 2007-2011 ST-Ericsson AB
* License terms: GNU General Public License (GPL) version 2
* U300 GPIO module.
* This can driver either of the two basic GPIO cores
* available in the U300 platforms:
* COH 901 335 - Used in DB3150 (U300 1.0) and DB3200 (U330 1.0)
* COH 901 571/3 - Used in DB3210 (U365 2.0) and DB3350 (U335 1.0)
- * Notice that you also have inline macros in <asm-arch/gpio.h>
- * Author: Linus Walleij <linus.walleij at stericsson.com>
+ * Author: Linus Walleij <linus.walleij at linaro.org>
* Author: Jonas Aaberg <jonas.aberg at stericsson.com>
- *
*/
#include <linux/module.h>
+#include <linux/irq.h>
#include <linux/interrupt.h>
#include <linux/delay.h>
#include <linux/errno.h>
@@ -24,677 +19,880 @@
#include <linux/err.h>
#include <linux/platform_device.h>
#include <linux/gpio.h>
+#include <linux/list.h>
+#include <linux/slab.h>
+#include <linux/gpio/u300.h>
-/* Reference to GPIO block clock */
-static struct clk *clk;
+/*
+ * Register definitions for COH 901 335 variant
+ */
+#define U300_335_PORT_STRIDE (0x1C)
+/* Port X Pin Data Register 32bit, this is both input and output (R/W) */
+#define U300_335_PXPDIR (0x00)
+#define U300_335_PXPDOR (0x00)
+/* Port X Pin Config Register 32bit (R/W) */
+#define U300_335_PXPCR (0x04)
+/* This register layout is the same in both blocks */
+#define U300_GPIO_PXPCR_ALL_PINS_MODE_MASK (0x0000FFFFUL)
+#define U300_GPIO_PXPCR_PIN_MODE_MASK (0x00000003UL)
+#define U300_GPIO_PXPCR_PIN_MODE_SHIFT (0x00000002UL)
+#define U300_GPIO_PXPCR_PIN_MODE_INPUT (0x00000000UL)
+#define U300_GPIO_PXPCR_PIN_MODE_OUTPUT_PUSH_PULL (0x00000001UL)
+#define U300_GPIO_PXPCR_PIN_MODE_OUTPUT_OPEN_DRAIN (0x00000002UL)
+#define U300_GPIO_PXPCR_PIN_MODE_OUTPUT_OPEN_SOURCE (0x00000003UL)
+/* Port X Interrupt Event Register 32bit (R/W) */
+#define U300_335_PXIEV (0x08)
+/* Port X Interrupt Enable Register 32bit (R/W) */
+#define U300_335_PXIEN (0x0C)
+/* Port X Interrupt Force Register 32bit (R/W) */
+#define U300_335_PXIFR (0x10)
+/* Port X Interrupt Config Register 32bit (R/W) */
+#define U300_335_PXICR (0x14)
+/* This register layout is the same in both blocks */
+#define U300_GPIO_PXICR_ALL_IRQ_CONFIG_MASK (0x000000FFUL)
+#define U300_GPIO_PXICR_IRQ_CONFIG_MASK (0x00000001UL)
+#define U300_GPIO_PXICR_IRQ_CONFIG_FALLING_EDGE (0x00000000UL)
+#define U300_GPIO_PXICR_IRQ_CONFIG_RISING_EDGE (0x00000001UL)
+/* Port X Pull-up Enable Register 32bit (R/W) */
+#define U300_335_PXPER (0x18)
+/* This register layout is the same in both blocks */
+#define U300_GPIO_PXPER_ALL_PULL_UP_DISABLE_MASK (0x000000FFUL)
+#define U300_GPIO_PXPER_PULL_UP_DISABLE (0x00000001UL)
+/* Control Register 32bit (R/W) */
+#define U300_335_CR (0x54)
+#define U300_335_CR_BLOCK_CLOCK_ENABLE (0x00000001UL)
-/* Memory resource */
-static struct resource *memres;
-static void __iomem *virtbase;
-static struct device *gpiodev;
+/*
+ * Register definitions for COH 901 571 / 3 variant
+ */
+#define U300_571_PORT_STRIDE (0x30)
+/*
+ * Control Register 32bit (R/W)
+ * bit 15-9 (mask 0x0000FE00) contains the number of cores. 8*cores
+ * gives the number of GPIO pins.
+ * bit 8-2 (mask 0x000001FC) contains the core version ID.
+ */
+#define U300_571_CR (0x00)
+#define U300_571_CR_SYNC_SEL_ENABLE (0x00000002UL)
+#define U300_571_CR_BLOCK_CLKRQ_ENABLE (0x00000001UL)
+/*
+ * These registers have the same layout and function as the corresponding
+ * COH 901 335 registers, just at different offset.
+ */
+#define U300_571_PXPDIR (0x04)
+#define U300_571_PXPDOR (0x08)
+#define U300_571_PXPCR (0x0C)
+#define U300_571_PXPER (0x10)
+#define U300_571_PXIEV (0x14)
+#define U300_571_PXIEN (0x18)
+#define U300_571_PXIFR (0x1C)
+#define U300_571_PXICR (0x20)
+
+/* 8 bits per port, no version has more than 7 ports */
+#define U300_GPIO_PINS_PER_PORT 8
+#define U300_GPIO_MAX (U300_GPIO_PINS_PER_PORT * 7)
+
+struct u300_gpio {
+ struct gpio_chip chip;
+ struct list_head port_list;
+ struct clk *clk;
+ struct resource *memres;
+ void __iomem *base;
+ struct device *dev;
+ int irq_base;
+ int users;
+ u32 stride;
+ /* Register offsets */
+ u32 pcr;
+ u32 dor;
+ u32 dir;
+ u32 per;
+ u32 icr;
+ u32 ien;
+ u32 iev;
+};
struct u300_gpio_port {
- const char *name;
+ struct list_head node;
+ struct u300_gpio *gpio;
+ char name[8];
int irq;
int number;
+ u8 toggle_edge_mode;
};
+/*
+ * Macro to expand to read a specific register found in the "gpio"
+ * struct. It requires the struct u300_gpio *gpio variable to exist in
+ * its context. It calculates the port offset from the given pin
+ * offset, muliplies by the port stride and adds the register offset
+ * so it provides a pointer to the desired register.
+ */
+#define U300_PIN_REG(pin, reg) \
+ (gpio->base + (pin >> 3) * gpio->stride + gpio->reg)
-static struct u300_gpio_port gpio_ports[] = {
- {
- .name = "gpio0",
- .number = 0,
- },
- {
- .name = "gpio1",
- .number = 1,
- },
- {
- .name = "gpio2",
- .number = 2,
- },
-#ifdef U300_COH901571_3
- {
- .name = "gpio3",
- .number = 3,
- },
- {
- .name = "gpio4",
- .number = 4,
- },
-#ifdef CONFIG_MACH_U300_BS335
- {
- .name = "gpio5",
- .number = 5,
- },
- {
- .name = "gpio6",
- .number = 6,
- },
-#endif
-#endif
+/*
+ * Provides a bitmask for a specific gpio pin inside an 8-bit GPIO
+ * register.
+ */
+#define U300_PIN_BIT(pin) \
+ (1 << (pin & 0x07))
+struct u300_gpio_confdata {
+ u16 bias_mode;
+ bool output;
+ int outval;
};
+/* BS335 has seven ports of 8 bits each = GPIO pins 0..55 */
+#define BS335_GPIO_NUM_PORTS 7
+/* BS365 has five ports of 8 bits each = GPIO pins 0..39 */
+#define BS365_GPIO_NUM_PORTS 5
-#ifdef U300_COH901571_3
+#define U300_FLOATING_INPUT { \
+ .bias_mode = GPIO_CONFIG_BIAS_FLOAT, \
+ .output = false, \
+}
-/* Default input value */
-#define DEFAULT_OUTPUT_LOW 0
-#define DEFAULT_OUTPUT_HIGH 1
+#define U300_PULL_UP_INPUT { \
+ .bias_mode = GPIO_CONFIG_BIAS_PULL_UP, \
+ .output = false, \
+}
-/* GPIO Pull-Up status */
-#define DISABLE_PULL_UP 0
-#define ENABLE_PULL_UP 1
+#define U300_OUTPUT_LOW { \
+ .output = true, \
+ .outval = 0, \
+}
-#define GPIO_NOT_USED 0
-#define GPIO_IN 1
-#define GPIO_OUT 2
+#define U300_OUTPUT_HIGH { \
+ .output = true, \
+ .outval = 1, \
+}
-struct u300_gpio_configuration_data {
- unsigned char pin_usage;
- unsigned char default_output_value;
- unsigned char pull_up;
-};
/* Initial configuration */
-const struct u300_gpio_configuration_data
-u300_gpio_config[U300_GPIO_NUM_PORTS][U300_GPIO_PINS_PER_PORT] = {
-#ifdef CONFIG_MACH_U300_BS335
+static struct __initdata u300_gpio_confdata
+bs335_gpio_config[BS335_GPIO_NUM_PORTS][U300_GPIO_PINS_PER_PORT] = {
/* Port 0, pins 0-7 */
{
- {GPIO_IN, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP},
- {GPIO_OUT, DEFAULT_OUTPUT_HIGH, DISABLE_PULL_UP},
- {GPIO_IN, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP},
- {GPIO_OUT, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP},
- {GPIO_OUT, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP},
- {GPIO_OUT, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP},
- {GPIO_OUT, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP},
- {GPIO_OUT, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP}
+ U300_FLOATING_INPUT,
+ U300_OUTPUT_HIGH,
+ U300_FLOATING_INPUT,
+ U300_OUTPUT_LOW,
+ U300_OUTPUT_LOW,
+ U300_OUTPUT_LOW,
+ U300_OUTPUT_LOW,
+ U300_OUTPUT_LOW,
},
/* Port 1, pins 0-7 */
{
- {GPIO_OUT, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP},
- {GPIO_OUT, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP},
- {GPIO_OUT, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP},
- {GPIO_IN, DEFAULT_OUTPUT_LOW, ENABLE_PULL_UP},
- {GPIO_IN, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP},
- {GPIO_OUT, DEFAULT_OUTPUT_HIGH, DISABLE_PULL_UP},
- {GPIO_OUT, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP},
- {GPIO_OUT, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP}
+ U300_OUTPUT_LOW,
+ U300_OUTPUT_LOW,
+ U300_OUTPUT_LOW,
+ U300_PULL_UP_INPUT,
+ U300_FLOATING_INPUT,
+ U300_OUTPUT_HIGH,
+ U300_OUTPUT_LOW,
+ U300_OUTPUT_LOW,
},
/* Port 2, pins 0-7 */
{
- {GPIO_IN, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP},
- {GPIO_IN, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP},
- {GPIO_IN, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP},
- {GPIO_IN, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP},
- {GPIO_OUT, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP},
- {GPIO_IN, DEFAULT_OUTPUT_LOW, ENABLE_PULL_UP},
- {GPIO_OUT, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP},
- {GPIO_IN, DEFAULT_OUTPUT_LOW, ENABLE_PULL_UP}
+ U300_FLOATING_INPUT,
+ U300_FLOATING_INPUT,
+ U300_FLOATING_INPUT,
+ U300_FLOATING_INPUT,
+ U300_OUTPUT_LOW,
+ U300_PULL_UP_INPUT,
+ U300_OUTPUT_LOW,
+ U300_PULL_UP_INPUT,
},
/* Port 3, pins 0-7 */
{
- {GPIO_IN, DEFAULT_OUTPUT_LOW, ENABLE_PULL_UP},
- {GPIO_OUT, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP},
- {GPIO_IN, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP},
- {GPIO_IN, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP},
- {GPIO_IN, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP},
- {GPIO_IN, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP},
- {GPIO_IN, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP},
- {GPIO_IN, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP}
+ U300_PULL_UP_INPUT,
+ U300_OUTPUT_LOW,
+ U300_FLOATING_INPUT,
+ U300_FLOATING_INPUT,
+ U300_FLOATING_INPUT,
+ U300_FLOATING_INPUT,
+ U300_FLOATING_INPUT,
+ U300_FLOATING_INPUT,
},
/* Port 4, pins 0-7 */
{
- {GPIO_IN, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP},
- {GPIO_IN, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP},
- {GPIO_IN, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP},
- {GPIO_IN, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP},
- {GPIO_IN, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP},
- {GPIO_IN, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP},
- {GPIO_IN, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP},
- {GPIO_IN, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP}
+ U300_FLOATING_INPUT,
+ U300_FLOATING_INPUT,
+ U300_FLOATING_INPUT,
+ U300_FLOATING_INPUT,
+ U300_FLOATING_INPUT,
+ U300_FLOATING_INPUT,
+ U300_FLOATING_INPUT,
+ U300_FLOATING_INPUT,
},
/* Port 5, pins 0-7 */
{
- {GPIO_IN, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP},
- {GPIO_IN, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP},
- {GPIO_IN, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP},
- {GPIO_IN, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP},
- {GPIO_IN, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP},
- {GPIO_IN, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP},
- {GPIO_IN, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP},
- {GPIO_IN, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP}
+ U300_FLOATING_INPUT,
+ U300_FLOATING_INPUT,
+ U300_FLOATING_INPUT,
+ U300_FLOATING_INPUT,
+ U300_FLOATING_INPUT,
+ U300_FLOATING_INPUT,
+ U300_FLOATING_INPUT,
+ U300_FLOATING_INPUT,
},
/* Port 6, pind 0-7 */
{
- {GPIO_IN, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP},
- {GPIO_IN, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP},
- {GPIO_IN, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP},
- {GPIO_IN, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP},
- {GPIO_IN, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP},
- {GPIO_IN, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP},
- {GPIO_IN, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP},
- {GPIO_IN, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP}
+ U300_FLOATING_INPUT,
+ U300_FLOATING_INPUT,
+ U300_FLOATING_INPUT,
+ U300_FLOATING_INPUT,
+ U300_FLOATING_INPUT,
+ U300_FLOATING_INPUT,
+ U300_FLOATING_INPUT,
+ U300_FLOATING_INPUT,
}
-#endif
+};
-#ifdef CONFIG_MACH_U300_BS365
+static struct __initdata u300_gpio_confdata
+bs365_gpio_config[BS365_GPIO_NUM_PORTS][U300_GPIO_PINS_PER_PORT] = {
/* Port 0, pins 0-7 */
{
- {GPIO_IN, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP},
- {GPIO_OUT, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP},
- {GPIO_IN, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP},
- {GPIO_OUT, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP},
- {GPIO_OUT, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP},
- {GPIO_OUT, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP},
- {GPIO_IN, DEFAULT_OUTPUT_LOW, ENABLE_PULL_UP},
- {GPIO_IN, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP}
+ U300_FLOATING_INPUT,
+ U300_OUTPUT_LOW,
+ U300_FLOATING_INPUT,
+ U300_OUTPUT_LOW,
+ U300_OUTPUT_LOW,
+ U300_OUTPUT_LOW,
+ U300_PULL_UP_INPUT,
+ U300_FLOATING_INPUT,
},
/* Port 1, pins 0-7 */
{
- {GPIO_OUT, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP},
- {GPIO_IN, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP},
- {GPIO_OUT, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP},
- {GPIO_IN, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP},
- {GPIO_IN, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP},
- {GPIO_OUT, DEFAULT_OUTPUT_HIGH, DISABLE_PULL_UP},
- {GPIO_OUT, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP},
- {GPIO_OUT, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP}
+ U300_OUTPUT_LOW,
+ U300_FLOATING_INPUT,
+ U300_OUTPUT_LOW,
+ U300_FLOATING_INPUT,
+ U300_FLOATING_INPUT,
+ U300_OUTPUT_HIGH,
+ U300_OUTPUT_LOW,
+ U300_OUTPUT_LOW,
},
/* Port 2, pins 0-7 */
{
- {GPIO_IN, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP},
- {GPIO_IN, DEFAULT_OUTPUT_LOW, ENABLE_PULL_UP},
- {GPIO_OUT, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP},
- {GPIO_OUT, DEFAULT_OUTPUT_LOW, DISABLE_PULL_UP},
- {GPIO_IN, DEFAULT_OUTPUT_LOW, ENABLE_PULL_UP},
- {GPIO_IN, DEFAULT_OUTPUT_LOW, ENABLE_PULL_UP},
- {GPIO_IN, DEFAULT_OUTPUT_LOW, ENABLE_PULL_UP},
- {GPIO_IN, DEFAULT_OUTPUT_LOW, ENABLE_PULL_UP}
+ U300_FLOATING_INPUT,
+ U300_PULL_UP_INPUT,
+ U300_OUTPUT_LOW,
+ U300_OUTPUT_LOW,
+ U300_PULL_UP_INPUT,
+ U300_PULL_UP_INPUT,
+ U300_PULL_UP_INPUT,
+ U300_PULL_UP_INPUT,
},
/* Port 3, pins 0-7 */
{
- {GPIO_IN, DEFAULT_OUTPUT_LOW, ENABLE_PULL_UP},
- {GPIO_IN, DEFAULT_OUTPUT_LOW, ENABLE_PULL_UP},
- {GPIO_IN, DEFAULT_OUTPUT_LOW, ENABLE_PULL_UP},
- {GPIO_IN, DEFAULT_OUTPUT_LOW, ENABLE_PULL_UP},
- {GPIO_IN, DEFAULT_OUTPUT_LOW, ENABLE_PULL_UP},
- {GPIO_IN, DEFAULT_OUTPUT_LOW, ENABLE_PULL_UP},
- {GPIO_IN, DEFAULT_OUTPUT_LOW, ENABLE_PULL_UP},
- {GPIO_IN, DEFAULT_OUTPUT_LOW, ENABLE_PULL_UP}
+ U300_PULL_UP_INPUT,
+ U300_PULL_UP_INPUT,
+ U300_PULL_UP_INPUT,
+ U300_PULL_UP_INPUT,
+ U300_PULL_UP_INPUT,
+ U300_PULL_UP_INPUT,
+ U300_PULL_UP_INPUT,
+ U300_PULL_UP_INPUT,
},
/* Port 4, pins 0-7 */
{
- {GPIO_IN, DEFAULT_OUTPUT_LOW, ENABLE_PULL_UP},
- {GPIO_IN, DEFAULT_OUTPUT_LOW, ENABLE_PULL_UP},
- {GPIO_IN, DEFAULT_OUTPUT_LOW, ENABLE_PULL_UP},
- {GPIO_IN, DEFAULT_OUTPUT_LOW, ENABLE_PULL_UP},
+ U300_PULL_UP_INPUT,
+ U300_PULL_UP_INPUT,
+ U300_PULL_UP_INPUT,
+ U300_PULL_UP_INPUT,
/* These 4 pins doesn't exist on DB3210 */
- {GPIO_OUT, DEFAULT_OUTPUT_LOW, ENABLE_PULL_UP},
- {GPIO_OUT, DEFAULT_OUTPUT_LOW, ENABLE_PULL_UP},
- {GPIO_OUT, DEFAULT_OUTPUT_LOW, ENABLE_PULL_UP},
- {GPIO_OUT, DEFAULT_OUTPUT_LOW, ENABLE_PULL_UP}
+ U300_OUTPUT_LOW,
+ U300_OUTPUT_LOW,
+ U300_OUTPUT_LOW,
+ U300_OUTPUT_LOW,
}
-#endif
-};
-#endif
-
-
-/* No users == we can power down GPIO */
-static int gpio_users;
-
-struct gpio_struct {
- int (*callback)(void *);
- void *data;
- int users;
};
-static struct gpio_struct gpio_pin[U300_GPIO_MAX];
-
-/*
- * Let drivers register callback in order to get notified when there is
- * an interrupt on the gpio pin
+/**
+ * to_u300_gpio() - get the pointer to u300_gpio
+ * @chip: the gpio chip member of the structure u300_gpio
*/
-int gpio_register_callback(unsigned gpio, int (*func)(void *arg), void *data)
+static inline struct u300_gpio *to_u300_gpio(struct gpio_chip *chip)
{
- if (gpio_pin[gpio].callback)
- dev_warn(gpiodev, "%s: WARNING: callback already "
- "registered for gpio pin#%d\n", __func__, gpio);
- gpio_pin[gpio].callback = func;
- gpio_pin[gpio].data = data;
-
- return 0;
+ return container_of(chip, struct u300_gpio, chip);
}
-EXPORT_SYMBOL(gpio_register_callback);
-int gpio_unregister_callback(unsigned gpio)
+static int u300_gpio_get(struct gpio_chip *chip, unsigned offset)
{
- if (!gpio_pin[gpio].callback)
- dev_warn(gpiodev, "%s: WARNING: callback already "
- "unregistered for gpio pin#%d\n", __func__, gpio);
- gpio_pin[gpio].callback = NULL;
- gpio_pin[gpio].data = NULL;
+ struct u300_gpio *gpio = to_u300_gpio(chip);
- return 0;
+ return readl(U300_PIN_REG(offset, dir)) & U300_PIN_BIT(offset);
}
-EXPORT_SYMBOL(gpio_unregister_callback);
-/* Non-zero means valid */
-int gpio_is_valid(int number)
+static void u300_gpio_set(struct gpio_chip *chip, unsigned offset, int value)
{
- if (number >= 0 &&
- number < (U300_GPIO_NUM_PORTS * U300_GPIO_PINS_PER_PORT))
- return 1;
- return 0;
-}
-EXPORT_SYMBOL(gpio_is_valid);
+ struct u300_gpio *gpio = to_u300_gpio(chip);
+ unsigned long flags;
+ u32 val;
-int gpio_request(unsigned gpio, const char *label)
-{
- if (gpio_pin[gpio].users)
- return -EINVAL;
- else
- gpio_pin[gpio].users++;
+ local_irq_save(flags);
- gpio_users++;
+ val = readl(U300_PIN_REG(offset, dor));
+ if (value)
+ writel(val | U300_PIN_BIT(offset), U300_PIN_REG(offset, dor));
+ else
+ writel(val & ~U300_PIN_BIT(offset), U300_PIN_REG(offset, dor));
- return 0;
+ local_irq_restore(flags);
}
-EXPORT_SYMBOL(gpio_request);
-void gpio_free(unsigned gpio)
+static int u300_gpio_direction_input(struct gpio_chip *chip, unsigned offset)
{
- gpio_users--;
- gpio_pin[gpio].users--;
- if (unlikely(gpio_pin[gpio].users < 0)) {
- dev_warn(gpiodev, "warning: gpio#%d release mismatch\n",
- gpio);
- gpio_pin[gpio].users = 0;
- }
-
- return;
-}
-EXPORT_SYMBOL(gpio_free);
+ struct u300_gpio *gpio = to_u300_gpio(chip);
+ unsigned long flags;
+ u32 val;
-/* This returns zero or nonzero */
-int gpio_get_value(unsigned gpio)
-{
- return readl(virtbase + U300_GPIO_PXPDIR +
- PIN_TO_PORT(gpio) * U300_GPIO_PORTX_SPACING) & (1 << (gpio & 0x07));
+ local_irq_save(flags);
+ val = readl(U300_PIN_REG(offset, pcr));
+ /* Mask out this pin, note 2 bits per setting */
+ val &= ~(U300_GPIO_PXPCR_PIN_MODE_MASK << ((offset & 0x07) << 1));
+ writel(val, U300_PIN_REG(offset, pcr));
+ local_irq_restore(flags);
+ return 0;
}
-EXPORT_SYMBOL(gpio_get_value);
-/*
- * We hope that the compiler will optimize away the unused branch
- * in case "value" is a constant
- */
-void gpio_set_value(unsigned gpio, int value)
+static int u300_gpio_direction_output(struct gpio_chip *chip, unsigned offset,
+ int value)
{
- u32 val;
+ struct u300_gpio *gpio = to_u300_gpio(chip);
unsigned long flags;
+ u32 oldmode;
+ u32 val;
local_irq_save(flags);
- if (value) {
- /* set */
- val = readl(virtbase + U300_GPIO_PXPDOR +
- PIN_TO_PORT(gpio) * U300_GPIO_PORTX_SPACING)
- & (1 << (gpio & 0x07));
- writel(val | (1 << (gpio & 0x07)), virtbase +
- U300_GPIO_PXPDOR +
- PIN_TO_PORT(gpio) * U300_GPIO_PORTX_SPACING);
- } else {
- /* clear */
- val = readl(virtbase + U300_GPIO_PXPDOR +
- PIN_TO_PORT(gpio) * U300_GPIO_PORTX_SPACING)
- & (1 << (gpio & 0x07));
- writel(val & ~(1 << (gpio & 0x07)), virtbase +
- U300_GPIO_PXPDOR +
- PIN_TO_PORT(gpio) * U300_GPIO_PORTX_SPACING);
+ val = readl(U300_PIN_REG(offset, pcr));
+ /*
+ * Drive mode must be set by the special mode set function, set
+ * push/pull mode by default if no mode has been selected.
+ */
+ oldmode = val & (U300_GPIO_PXPCR_PIN_MODE_MASK <<
+ ((offset & 0x07) << 1));
+ /* mode = 0 means input, else some mode is already set */
+ if (oldmode == 0) {
+ val &= ~(U300_GPIO_PXPCR_PIN_MODE_MASK <<
+ ((offset & 0x07) << 1));
+ val |= (U300_GPIO_PXPCR_PIN_MODE_OUTPUT_PUSH_PULL
+ << ((offset & 0x07) << 1));
+ writel(val, U300_PIN_REG(offset, pcr));
}
+ u300_gpio_set(chip, offset, value);
local_irq_restore(flags);
+ return 0;
+}
+
+static int u300_gpio_to_irq(struct gpio_chip *chip, unsigned offset)
+{
+ struct u300_gpio *gpio = to_u300_gpio(chip);
+ int retirq = gpio->irq_base + offset;
+
+ dev_dbg(gpio->dev, "request IRQ for GPIO %d, return %d\n", offset,
+ retirq);
+ return retirq;
}
-EXPORT_SYMBOL(gpio_set_value);
-int gpio_direction_input(unsigned gpio)
+static int u300_gpio_config(struct gpio_chip *chip, unsigned offset,
+ u16 param, unsigned long *data)
{
+ struct u300_gpio *gpio = to_u300_gpio(chip);
unsigned long flags;
u32 val;
- if (gpio > U300_GPIO_MAX)
- return -EINVAL;
-
local_irq_save(flags);
- val = readl(virtbase + U300_GPIO_PXPCR + PIN_TO_PORT(gpio) *
- U300_GPIO_PORTX_SPACING);
- /* Mask out this pin*/
- val &= ~(U300_GPIO_PXPCR_PIN_MODE_MASK << ((gpio & 0x07) << 1));
- /* This is not needed since it sets the bits to zero.*/
- /* val |= (U300_GPIO_PXPCR_PIN_MODE_INPUT << (gpio*2)); */
- writel(val, virtbase + U300_GPIO_PXPCR + PIN_TO_PORT(gpio) *
- U300_GPIO_PORTX_SPACING);
+ switch (param) {
+ case GPIO_CONFIG_BIAS_UNKNOWN:
+ case GPIO_CONFIG_BIAS_FLOAT:
+ val = readl(U300_PIN_REG(offset, per));
+ writel(val | U300_PIN_BIT(offset), U300_PIN_REG(offset, per));
+ break;
+ case GPIO_CONFIG_BIAS_PULL_UP:
+ val = readl(U300_PIN_REG(offset, per));
+ writel(val & ~U300_PIN_BIT(offset), U300_PIN_REG(offset, per));
+ break;
+ case GPIO_CONFIG_DRIVE_PUSH_PULL:
+ val = readl(U300_PIN_REG(offset, pcr));
+ val &= ~(U300_GPIO_PXPCR_PIN_MODE_MASK
+ << ((offset & 0x07) << 1));
+ val |= (U300_GPIO_PXPCR_PIN_MODE_OUTPUT_PUSH_PULL
+ << ((offset & 0x07) << 1));
+ writel(val, U300_PIN_REG(offset, pcr));
+ break;
+ case GPIO_CONFIG_DRIVE_OPEN_DRAIN:
+ val = readl(U300_PIN_REG(offset, pcr));
+ val &= ~(U300_GPIO_PXPCR_PIN_MODE_MASK
+ << ((offset & 0x07) << 1));
+ val |= (U300_GPIO_PXPCR_PIN_MODE_OUTPUT_OPEN_DRAIN
+ << ((offset & 0x07) << 1));
+ writel(val, U300_PIN_REG(offset, pcr));
+ break;
+ case GPIO_CONFIG_DRIVE_OPEN_SOURCE:
+ val = readl(U300_PIN_REG(offset, pcr));
+ val &= ~(U300_GPIO_PXPCR_PIN_MODE_MASK
+ << ((offset & 0x07) << 1));
+ val |= (U300_GPIO_PXPCR_PIN_MODE_OUTPUT_OPEN_SOURCE
+ << ((offset & 0x07) << 1));
+ writel(val, U300_PIN_REG(offset, pcr));
+ break;
+ default:
+ local_irq_restore(flags);
+ dev_err(gpio->dev, "illegal configuration requested\n");
+ return -EINVAL;
+ }
local_irq_restore(flags);
return 0;
}
-EXPORT_SYMBOL(gpio_direction_input);
-int gpio_direction_output(unsigned gpio, int value)
+
+/* External function to configure pins */
+int u300_gpio_set_config(unsigned gpio, u16 param, unsigned long *data)
{
- unsigned long flags;
- u32 val;
+ struct gpio_chip *chip = gpio_to_chip(gpio);
+ unsigned offset = gpio - chip->base;
- if (gpio > U300_GPIO_MAX)
- return -EINVAL;
+ return u300_gpio_config(chip, offset, param, data);
+}
- local_irq_save(flags);
- val = readl(virtbase + U300_GPIO_PXPCR + PIN_TO_PORT(gpio) *
- U300_GPIO_PORTX_SPACING);
- /* Mask out this pin */
- val &= ~(U300_GPIO_PXPCR_PIN_MODE_MASK << ((gpio & 0x07) << 1));
- /*
- * FIXME: configure for push/pull, open drain or open source per pin
- * in setup. The current driver will only support push/pull.
- */
- val |= (U300_GPIO_PXPCR_PIN_MODE_OUTPUT_PUSH_PULL
- << ((gpio & 0x07) << 1));
- writel(val, virtbase + U300_GPIO_PXPCR + PIN_TO_PORT(gpio) *
- U300_GPIO_PORTX_SPACING);
- gpio_set_value(gpio, value);
- local_irq_restore(flags);
- return 0;
+static struct gpio_chip u300_gpio_chip = {
+ .label = "u300-gpio-chip",
+ .owner = THIS_MODULE,
+ .get = u300_gpio_get,
+ .set = u300_gpio_set,
+ .direction_input = u300_gpio_direction_input,
+ .direction_output = u300_gpio_direction_output,
+ .to_irq = u300_gpio_to_irq,
+};
+
+static void u300_toggle_trigger(struct u300_gpio *gpio, unsigned offset)
+{
+ u32 val;
+
+ val = readl(U300_PIN_REG(offset, icr));
+ /* Set mode depending on state */
+ if (u300_gpio_get(&gpio->chip, offset)) {
+ /* High now, let's trigger on falling edge next then */
+ writel(val & ~U300_PIN_BIT(offset), U300_PIN_REG(offset, icr));
+ dev_dbg(gpio->dev, "next IRQ on falling edge on pin %d\n",
+ offset);
+ } else {
+ /* Low now, let's trigger on rising edge next then */
+ writel(val | U300_PIN_BIT(offset), U300_PIN_REG(offset, icr));
+ dev_dbg(gpio->dev, "next IRQ on rising edge on pin %d\n",
+ offset);
+ }
}
-EXPORT_SYMBOL(gpio_direction_output);
-/*
- * Enable an IRQ, edge is rising edge (!= 0) or falling edge (==0).
- */
-void enable_irq_on_gpio_pin(unsigned gpio, int edge)
+static int u300_gpio_irq_type(struct irq_data *d, unsigned trigger)
{
+ struct u300_gpio_port *port = irq_data_get_irq_chip_data(d);
+ struct u300_gpio *gpio = port->gpio;
+ int offset = d->irq - gpio->irq_base;
u32 val;
- unsigned long flags;
- local_irq_save(flags);
- val = readl(virtbase + U300_GPIO_PXIEN + PIN_TO_PORT(gpio) *
- U300_GPIO_PORTX_SPACING);
- val |= (1 << (gpio & 0x07));
- writel(val, virtbase + U300_GPIO_PXIEN + PIN_TO_PORT(gpio) *
- U300_GPIO_PORTX_SPACING);
- val = readl(virtbase + U300_GPIO_PXICR + PIN_TO_PORT(gpio) *
- U300_GPIO_PORTX_SPACING);
- if (edge)
- val |= (1 << (gpio & 0x07));
- else
- val &= ~(1 << (gpio & 0x07));
- writel(val, virtbase + U300_GPIO_PXICR + PIN_TO_PORT(gpio) *
- U300_GPIO_PORTX_SPACING);
- local_irq_restore(flags);
+ if ((trigger & IRQF_TRIGGER_RISING) &&
+ (trigger & IRQF_TRIGGER_FALLING)) {
+ /*
+ * The GPIO block can only trigger on falling OR rising edges,
+ * not both. So we need to toggle the mode whenever the pin
+ * goes from one state to the other with a special state flag
+ */
+ dev_dbg(gpio->dev,
+ "trigger on both rising and falling edge on pin %d\n",
+ offset);
+ port->toggle_edge_mode |= U300_PIN_BIT(offset);
+ u300_toggle_trigger(gpio, offset);
+ } else if (trigger & IRQF_TRIGGER_RISING) {
+ dev_dbg(gpio->dev, "trigger on rising edge on pin %d\n",
+ offset);
+ val = readl(U300_PIN_REG(offset, icr));
+ writel(val | U300_PIN_BIT(offset), U300_PIN_REG(offset, icr));
+ port->toggle_edge_mode &= ~U300_PIN_BIT(offset);
+ } else if (trigger & IRQF_TRIGGER_FALLING) {
+ dev_dbg(gpio->dev, "trigger on falling edge on pin %d\n",
+ offset);
+ val = readl(U300_PIN_REG(offset, icr));
+ writel(val & ~U300_PIN_BIT(offset), U300_PIN_REG(offset, icr));
+ port->toggle_edge_mode &= ~U300_PIN_BIT(offset);
+ }
+
+ return 0;
}
-EXPORT_SYMBOL(enable_irq_on_gpio_pin);
-void disable_irq_on_gpio_pin(unsigned gpio)
+static void u300_gpio_irq_enable(struct irq_data *d)
{
+ struct u300_gpio_port *port = irq_data_get_irq_chip_data(d);
+ struct u300_gpio *gpio = port->gpio;
+ int offset = d->irq - gpio->irq_base;
u32 val;
unsigned long flags;
local_irq_save(flags);
- val = readl(virtbase + U300_GPIO_PXIEN + PIN_TO_PORT(gpio) *
- U300_GPIO_PORTX_SPACING);
- val &= ~(1 << (gpio & 0x07));
- writel(val, virtbase + U300_GPIO_PXIEN + PIN_TO_PORT(gpio) *
- U300_GPIO_PORTX_SPACING);
+ val = readl(U300_PIN_REG(offset, ien));
+ writel(val | U300_PIN_BIT(offset), U300_PIN_REG(offset, ien));
local_irq_restore(flags);
}
-EXPORT_SYMBOL(disable_irq_on_gpio_pin);
-/* Enable (value == 0) or disable (value == 1) internal pullup */
-void gpio_pullup(unsigned gpio, int value)
+static void u300_gpio_irq_disable(struct irq_data *d)
{
+ struct u300_gpio_port *port = irq_data_get_irq_chip_data(d);
+ struct u300_gpio *gpio = port->gpio;
+ int offset = d->irq - gpio->irq_base;
u32 val;
unsigned long flags;
local_irq_save(flags);
- if (value) {
- val = readl(virtbase + U300_GPIO_PXPER + PIN_TO_PORT(gpio) *
- U300_GPIO_PORTX_SPACING);
- writel(val | (1 << (gpio & 0x07)), virtbase + U300_GPIO_PXPER +
- PIN_TO_PORT(gpio) * U300_GPIO_PORTX_SPACING);
- } else {
- val = readl(virtbase + U300_GPIO_PXPER + PIN_TO_PORT(gpio) *
- U300_GPIO_PORTX_SPACING);
- writel(val & ~(1 << (gpio & 0x07)), virtbase + U300_GPIO_PXPER +
- PIN_TO_PORT(gpio) * U300_GPIO_PORTX_SPACING);
- }
+ val = readl(U300_PIN_REG(offset, ien));
+ writel(val & ~U300_PIN_BIT(offset), U300_PIN_REG(offset, ien));
local_irq_restore(flags);
}
-EXPORT_SYMBOL(gpio_pullup);
-static irqreturn_t gpio_irq_handler(int irq, void *dev_id)
+static struct irq_chip u300_gpio_irqchip = {
+ .name = "u300-gpio-irqchip",
+ .irq_enable = u300_gpio_irq_enable,
+ .irq_disable = u300_gpio_irq_disable,
+ .irq_set_type = u300_gpio_irq_type,
+
+};
+
+static void u300_gpio_irq_handler(unsigned irq, struct irq_desc *desc)
{
- struct u300_gpio_port *port = dev_id;
- u32 val;
- int pin;
+ struct u300_gpio_port *port = irq_get_handler_data(irq);
+ struct u300_gpio *gpio = port->gpio;
+ int pinoffset = port->number << 3; /* get the right stride */
+ unsigned long val;
+ desc->irq_data.chip->irq_ack(&desc->irq_data);
/* Read event register */
- val = readl(virtbase + U300_GPIO_PXIEV + port->number *
- U300_GPIO_PORTX_SPACING);
- /* Mask with enable register */
- val &= readl(virtbase + U300_GPIO_PXIEV + port->number *
- U300_GPIO_PORTX_SPACING);
+ val = readl(U300_PIN_REG(pinoffset, iev));
/* Mask relevant bits */
- val &= U300_GPIO_PXIEV_ALL_IRQ_EVENT_MASK;
+ val &= 0xFFU; /* 8 bits per port */
/* ACK IRQ (clear event) */
- writel(val, virtbase + U300_GPIO_PXIEV + port->number *
- U300_GPIO_PORTX_SPACING);
- /* Print message */
- while (val != 0) {
- unsigned gpio;
-
- pin = __ffs(val);
- /* mask off this pin */
- val &= ~(1 << pin);
- gpio = (port->number << 3) + pin;
-
- if (gpio_pin[gpio].callback)
- (void)gpio_pin[gpio].callback(gpio_pin[gpio].data);
- else
- dev_dbg(gpiodev, "stray GPIO IRQ on line %d\n",
- gpio);
+ writel(val, U300_PIN_REG(pinoffset, iev));
+
+ /* Call IRQ handler */
+ if (val != 0) {
+ int irqoffset;
+
+ for_each_set_bit(irqoffset, &val, U300_GPIO_PINS_PER_PORT) {
+ int pin_irq = gpio->irq_base + (port->number << 3)
+ + irqoffset;
+ int offset = pinoffset + irqoffset;
+
+ dev_dbg(gpio->dev, "GPIO IRQ %d on pin %d\n",
+ pin_irq, offset);
+ generic_handle_irq(pin_irq);
+ /*
+ * Triggering IRQ on both rising and falling edge
+ * needs mockery
+ */
+ if (port->toggle_edge_mode & U300_PIN_BIT(offset))
+ u300_toggle_trigger(gpio, offset);
+ }
}
- return IRQ_HANDLED;
+
+ desc->irq_data.chip->irq_unmask(&desc->irq_data);
}
-static void gpio_set_initial_values(void)
+static void __init u300_gpio_init_pin(struct u300_gpio *gpio,
+ int offset,
+ struct u300_gpio_confdata *conf)
{
-#ifdef U300_COH901571_3
- int i, j;
- unsigned long flags;
- u32 val;
+ /* Set mode: input or output */
+ if (conf->output) {
+ u300_gpio_direction_output(&gpio->chip, offset, conf->outval);
- /* Write default values to all pins */
- for (i = 0; i < U300_GPIO_NUM_PORTS; i++) {
- val = 0;
- for (j = 0; j < 8; j++)
- val |= (u32) (u300_gpio_config[i][j].default_output_value != DEFAULT_OUTPUT_LOW) << j;
- local_irq_save(flags);
- writel(val, virtbase + U300_GPIO_PXPDOR + i * U300_GPIO_PORTX_SPACING);
- local_irq_restore(flags);
+ /* Deactivate bias mode for output */
+ u300_gpio_config(&gpio->chip, offset, GPIO_CONFIG_BIAS_FLOAT,
+ NULL);
+
+ /* Set drive mode for output */
+ u300_gpio_config(&gpio->chip, offset,
+ GPIO_CONFIG_DRIVE_PUSH_PULL, NULL);
+
+ dev_dbg(gpio->dev, "set up pin %d as output, value: %d\n",
+ offset, conf->outval);
+ } else {
+ u300_gpio_direction_input(&gpio->chip, offset);
+
+ /* Always set output low on input pins */
+ u300_gpio_set(&gpio->chip, offset, 0);
+
+ /* Set bias mode for input */
+ u300_gpio_config(&gpio->chip, offset, conf->bias_mode, NULL);
+
+ dev_dbg(gpio->dev, "set up pin %d as input, bias: %04x\n",
+ offset, conf->bias_mode);
}
+}
- /*
- * Put all pins that are set to either 'GPIO_OUT' or 'GPIO_NOT_USED'
- * to output and 'GPIO_IN' to input for each port. And initialize
- * default value on outputs.
- */
- for (i = 0; i < U300_GPIO_NUM_PORTS; i++) {
- for (j = 0; j < U300_GPIO_PINS_PER_PORT; j++) {
- local_irq_save(flags);
- val = readl(virtbase + U300_GPIO_PXPCR +
- i * U300_GPIO_PORTX_SPACING);
- /* Mask out this pin */
- val &= ~(U300_GPIO_PXPCR_PIN_MODE_MASK << (j << 1));
-
- if (u300_gpio_config[i][j].pin_usage != GPIO_IN)
- val |= (U300_GPIO_PXPCR_PIN_MODE_OUTPUT_PUSH_PULL << (j << 1));
- writel(val, virtbase + U300_GPIO_PXPCR +
- i * U300_GPIO_PORTX_SPACING);
- local_irq_restore(flags);
+static void __init u300_gpio_init_coh901571(struct u300_gpio *gpio,
+ struct u300_gpio_platform *plat)
+{
+ int i, j;
+
+ /* Write default config and values to all pins */
+ for (i = 0; i < plat->ports; i++) {
+ for (j = 0; j < 8; j++) {
+ struct u300_gpio_confdata *conf;
+ int offset = (i*8) + j;
+
+ if (plat->variant == U300_GPIO_COH901571_3_BS335)
+ conf = &bs335_gpio_config[i][j];
+ else if (plat->variant == U300_GPIO_COH901571_3_BS365)
+ conf = &bs365_gpio_config[i][j];
+ else
+ break;
+
+ u300_gpio_init_pin(gpio, offset, conf);
}
}
+}
- /* Enable or disable the internal pull-ups in the GPIO ASIC block */
- for (i = 0; i < U300_GPIO_MAX; i++) {
- val = 0;
- for (j = 0; j < 8; j++)
- val |= (u32)((u300_gpio_config[i][j].pull_up == DISABLE_PULL_UP) << j);
- local_irq_save(flags);
- writel(val, virtbase + U300_GPIO_PXPER + i * U300_GPIO_PORTX_SPACING);
- local_irq_restore(flags);
+static inline void u300_gpio_free_ports(struct u300_gpio *gpio)
+{
+ struct u300_gpio_port *port;
+ struct list_head *p, *n;
+
+ list_for_each_safe(p, n, &gpio->port_list) {
+ port = list_entry(p, struct u300_gpio_port, node);
+ list_del(&port->node);
+ free_irq(port->irq, port);
+ kfree(port);
}
-#endif
}
-static int __init gpio_probe(struct platform_device *pdev)
+static int __init u300_gpio_probe(struct platform_device *pdev)
{
- u32 val;
+ struct u300_gpio_platform *plat = dev_get_platdata(&pdev->dev);
+ struct u300_gpio *gpio;
int err = 0;
+ int portno;
+ u32 val;
+ u32 ifr;
int i;
- int num_irqs;
- gpiodev = &pdev->dev;
- memset(gpio_pin, 0, sizeof(gpio_pin));
+ gpio = kzalloc(sizeof(struct u300_gpio), GFP_KERNEL);
+ if (gpio == NULL) {
+ dev_err(&pdev->dev, "failed to allocate memory\n");
+ return -ENOMEM;
+ }
+
+ gpio->chip = u300_gpio_chip;
+ gpio->chip.ngpio = plat->ports * U300_GPIO_PINS_PER_PORT;
+ gpio->irq_base = plat->gpio_irq_base;
+ gpio->chip.dev = &pdev->dev;
+ gpio->chip.base = plat->gpio_base;
+ gpio->dev = &pdev->dev;
/* Get GPIO clock */
- clk = clk_get(&pdev->dev, NULL);
- if (IS_ERR(clk)) {
- err = PTR_ERR(clk);
- dev_err(gpiodev, "could not get GPIO clock\n");
+ gpio->clk = clk_get(gpio->dev, NULL);
+ if (IS_ERR(gpio->clk)) {
+ err = PTR_ERR(gpio->clk);
+ dev_err(gpio->dev, "could not get GPIO clock\n");
goto err_no_clk;
}
- err = clk_enable(clk);
+ err = clk_enable(gpio->clk);
if (err) {
- dev_err(gpiodev, "could not enable GPIO clock\n");
+ dev_err(gpio->dev, "could not enable GPIO clock\n");
goto err_no_clk_enable;
}
- memres = platform_get_resource(pdev, IORESOURCE_MEM, 0);
- if (!memres)
+ gpio->memres = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ if (!gpio->memres) {
+ dev_err(gpio->dev, "could not get GPIO memory resource\n");
+ err = -ENODEV;
goto err_no_resource;
+ }
- if (request_mem_region(memres->start, memres->end - memres->start, "GPIO Controller")
+ if (request_mem_region(gpio->memres->start,
+ resource_size(gpio->memres),
+ "GPIO Controller")
== NULL) {
+ dev_err(gpio->dev, "could not reserve GPIO memory region\n");
err = -ENODEV;
goto err_no_ioregion;
}
- virtbase = ioremap(memres->start, resource_size(memres));
- if (!virtbase) {
+ gpio->base = ioremap(gpio->memres->start, resource_size(gpio->memres));
+ if (!gpio->base) {
err = -ENOMEM;
goto err_no_ioremap;
}
- dev_info(gpiodev, "remapped 0x%08x to %p\n",
- memres->start, virtbase);
-
-#ifdef U300_COH901335
- dev_info(gpiodev, "initializing GPIO Controller COH 901 335\n");
- /* Turn on the GPIO block */
- writel(U300_GPIO_CR_BLOCK_CLOCK_ENABLE, virtbase + U300_GPIO_CR);
-#endif
-
-#ifdef U300_COH901571_3
- dev_info(gpiodev, "initializing GPIO Controller COH 901 571/3\n");
- val = readl(virtbase + U300_GPIO_CR);
- dev_info(gpiodev, "COH901571/3 block version: %d, " \
- "number of cores: %d\n",
- ((val & 0x0000FE00) >> 9),
- ((val & 0x000001FC) >> 2));
- writel(U300_GPIO_CR_BLOCK_CLKRQ_ENABLE, virtbase + U300_GPIO_CR);
-#endif
-
- gpio_set_initial_values();
-
- for (num_irqs = 0 ; num_irqs < U300_GPIO_NUM_PORTS; num_irqs++) {
-
- gpio_ports[num_irqs].irq =
- platform_get_irq_byname(pdev,
- gpio_ports[num_irqs].name);
-
- err = request_irq(gpio_ports[num_irqs].irq,
- gpio_irq_handler, IRQF_DISABLED,
- gpio_ports[num_irqs].name,
- &gpio_ports[num_irqs]);
- if (err) {
- dev_err(gpiodev, "cannot allocate IRQ for %s!\n",
- gpio_ports[num_irqs].name);
- goto err_no_irq;
+
+ if (plat->variant == U300_GPIO_COH901335) {
+ dev_info(gpio->dev,
+ "initializing GPIO Controller COH 901 335\n");
+ gpio->stride = U300_335_PORT_STRIDE;
+ gpio->pcr = U300_335_PXPCR;
+ gpio->dor = U300_335_PXPDOR;
+ gpio->dir = U300_335_PXPDIR;
+ gpio->per = U300_335_PXPER;
+ gpio->icr = U300_335_PXICR;
+ gpio->ien = U300_335_PXIEN;
+ gpio->iev = U300_335_PXIEV;
+ ifr = U300_335_PXIFR;
+
+ /* Turn on the GPIO block */
+ writel(U300_335_CR_BLOCK_CLOCK_ENABLE,
+ gpio->base + U300_335_CR);
+ } else if (plat->variant == U300_GPIO_COH901571_3_BS335 ||
+ plat->variant == U300_GPIO_COH901571_3_BS365) {
+ dev_info(gpio->dev,
+ "initializing GPIO Controller COH 901 571/3\n");
+ gpio->stride = U300_571_PORT_STRIDE;
+ gpio->pcr = U300_571_PXPCR;
+ gpio->dor = U300_571_PXPDOR;
+ gpio->dir = U300_571_PXPDIR;
+ gpio->per = U300_571_PXPER;
+ gpio->icr = U300_571_PXICR;
+ gpio->ien = U300_571_PXIEN;
+ gpio->iev = U300_571_PXIEV;
+ ifr = U300_571_PXIFR;
+
+ val = readl(gpio->base + U300_571_CR);
+ dev_info(gpio->dev, "COH901571/3 block version: %d, " \
+ "number of cores: %d totalling %d pins\n",
+ ((val & 0x000001FC) >> 2),
+ ((val & 0x0000FE00) >> 9),
+ ((val & 0x0000FE00) >> 9) * 8);
+ writel(U300_571_CR_BLOCK_CLKRQ_ENABLE,
+ gpio->base + U300_571_CR);
+ u300_gpio_init_coh901571(gpio, plat);
+ } else {
+ dev_err(gpio->dev, "unknown block variant\n");
+ err = -ENODEV;
+ goto err_unknown_variant;
+ }
+
+ /* Add each port with its IRQ separately */
+ INIT_LIST_HEAD(&gpio->port_list);
+ for (portno = 0 ; portno < plat->ports; portno++) {
+ struct u300_gpio_port *port =
+ kmalloc(sizeof(struct u300_gpio_port), GFP_KERNEL);
+
+ if (!port) {
+ dev_err(gpio->dev, "out of memory\n");
+ err = -ENOMEM;
+ goto err_no_port;
+ }
+
+ snprintf(port->name, 8, "gpio%d", portno);
+ port->number = portno;
+ port->gpio = gpio;
+
+ port->irq = platform_get_irq_byname(pdev,
+ port->name);
+
+ dev_dbg(gpio->dev, "register IRQ %d for %s\n", port->irq,
+ port->name);
+
+ irq_set_chained_handler(port->irq, u300_gpio_irq_handler);
+ irq_set_handler_data(port->irq, port);
+
+ /* For each GPIO pin set the unique IRQ handler */
+ for (i = 0; i < U300_GPIO_PINS_PER_PORT; i++) {
+ int irqno = gpio->irq_base + (portno << 3) + i;
+
+ dev_dbg(gpio->dev, "handler for IRQ %d on %s\n",
+ irqno, port->name);
+ irq_set_chip_and_handler(irqno, &u300_gpio_irqchip,
+ handle_simple_irq);
+ set_irq_flags(irqno, IRQF_VALID);
+ irq_set_chip_data(irqno, port);
}
- /* Turns off PortX_irq_force */
- writel(0x0, virtbase + U300_GPIO_PXIFR +
- num_irqs * U300_GPIO_PORTX_SPACING);
+
+ /* Turns off irq force (test register) for this port */
+ writel(0x0, gpio->base + portno * gpio->stride + ifr);
+
+ list_add_tail(&port->node, &gpio->port_list);
}
+ dev_dbg(gpio->dev, "initialized %d GPIO ports\n", portno);
+
+ err = gpiochip_add(&gpio->chip);
+ if (err) {
+ dev_err(gpio->dev, "unable to add gpiochip: %d\n", err);
+ goto err_no_chip;
+ }
+
+ platform_set_drvdata(pdev, gpio);
return 0;
- err_no_irq:
- for (i = 0; i < num_irqs; i++)
- free_irq(gpio_ports[i].irq, &gpio_ports[i]);
- iounmap(virtbase);
- err_no_ioremap:
- release_mem_region(memres->start, memres->end - memres->start);
- err_no_ioregion:
- err_no_resource:
- clk_disable(clk);
- err_no_clk_enable:
- clk_put(clk);
- err_no_clk:
- dev_info(gpiodev, "module ERROR:%d\n", err);
+err_no_chip:
+err_no_port:
+ u300_gpio_free_ports(gpio);
+err_unknown_variant:
+ iounmap(gpio->base);
+err_no_ioremap:
+ release_mem_region(gpio->memres->start, resource_size(gpio->memres));
+err_no_ioregion:
+err_no_resource:
+ clk_disable(gpio->clk);
+err_no_clk_enable:
+ clk_put(gpio->clk);
+err_no_clk:
+ kfree(gpio);
+ dev_info(&pdev->dev, "module ERROR:%d\n", err);
return err;
}
-static int __exit gpio_remove(struct platform_device *pdev)
+static int __exit u300_gpio_remove(struct platform_device *pdev)
{
- int i;
+ struct u300_gpio_platform *plat = dev_get_platdata(&pdev->dev);
+ struct u300_gpio *gpio = platform_get_drvdata(pdev);
+ int err;
/* Turn off the GPIO block */
- writel(0x00000000U, virtbase + U300_GPIO_CR);
- for (i = 0 ; i < U300_GPIO_NUM_PORTS; i++)
- free_irq(gpio_ports[i].irq, &gpio_ports[i]);
- iounmap(virtbase);
- release_mem_region(memres->start, memres->end - memres->start);
- clk_disable(clk);
- clk_put(clk);
+ if (plat->variant == U300_GPIO_COH901335)
+ writel(0x00000000U, gpio->base + U300_335_CR);
+ if (plat->variant == U300_GPIO_COH901571_3_BS335 ||
+ plat->variant == U300_GPIO_COH901571_3_BS365)
+ writel(0x00000000U, gpio->base + U300_571_CR);
+
+ err = gpiochip_remove(&gpio->chip);
+ if (err < 0) {
+ dev_err(gpio->dev, "unable to remove gpiochip: %d\n", err);
+ return err;
+ }
+ u300_gpio_free_ports(gpio);
+ iounmap(gpio->base);
+ release_mem_region(gpio->memres->start,
+ resource_size(gpio->memres));
+ clk_disable(gpio->clk);
+ clk_put(gpio->clk);
+ platform_set_drvdata(pdev, NULL);
+ kfree(gpio);
return 0;
}
-static struct platform_driver gpio_driver = {
+static struct platform_driver u300_gpio_driver = {
.driver = {
.name = "u300-gpio",
},
- .remove = __exit_p(gpio_remove),
+ .remove = __exit_p(u300_gpio_remove),
};
static int __init u300_gpio_init(void)
{
- return platform_driver_probe(&gpio_driver, gpio_probe);
+ return platform_driver_probe(&u300_gpio_driver, u300_gpio_probe);
}
static void __exit u300_gpio_exit(void)
{
- platform_driver_unregister(&gpio_driver);
+ platform_driver_unregister(&u300_gpio_driver);
}
arch_initcall(u300_gpio_init);
module_exit(u300_gpio_exit);
MODULE_AUTHOR("Linus Walleij <linus.walleij at stericsson.com>");
-
-#ifdef U300_COH901571_3
-MODULE_DESCRIPTION("ST-Ericsson AB COH 901 571/3 GPIO driver");
-#endif
-
-#ifdef U300_COH901335
-MODULE_DESCRIPTION("ST-Ericsson AB COH 901 335 GPIO driver");
-#endif
-
+MODULE_DESCRIPTION("ST-Ericsson AB COH 901 335/COH 901 571/3 GPIO driver");
MODULE_LICENSE("GPL");
diff --git a/include/linux/gpio/u300.h b/include/linux/gpio/u300.h
new file mode 100644
index 0000000..b54063e
--- /dev/null
+++ b/include/linux/gpio/u300.h
@@ -0,0 +1,82 @@
+/*
+ * U300 GPIO platform data header
+ * Copyright (C) 2011 ST-Ericsson SA
+ * Written on behalf of Linaro for ST-Ericsson
+ *
+ * Author: Linus Walleij <linus.walleij at linaro.org>
+ *
+ * License terms: GNU General Public License (GPL) version 2
+ */
+
+/**
+ * enum u300_gpio_variant - the type of U300 GPIO employed
+ */
+enum u300_gpio_variant {
+ U300_GPIO_COH901335,
+ U300_GPIO_COH901571_3_BS335,
+ U300_GPIO_COH901571_3_BS365,
+};
+
+/**
+ * struct u300_gpio_platform - U300 GPIO platform data
+ * @variant: IP block variant
+ * @ports: number of GPIO block ports
+ * @gpio_base: first GPIO number for this block (use a free range)
+ * @gpio_irq_base: first GPIO IRQ number for this block (use a free range)
+ */
+struct u300_gpio_platform {
+ enum u300_gpio_variant variant;
+ u8 ports;
+ int gpio_base;
+ int gpio_irq_base;
+};
+
+/*
+ * Bias modes for GPIOs - if you have more biases, add them here or provide
+ * custom enumerators for your driver if you find they are not generally
+ * useful.
+ *
+ * GPIO_CONFIG_BIAS_UNKNOWN: this bias mode is not known to us
+ * GPIO_CONFIG_BIAS_FLOAT: no specific bias, the GPIO will float or state
+ * is not controlled by software
+ * GPIO_CONFIG_BIAS_PULL_UP: the GPIO will be pulled up (usually with high
+ * impedance to VDD)
+ * GPIO_CONFIG_BIAS_PULL_DOWN: the GPIO will be pulled down (usually with high
+ * impedance to GROUND)
+ * GPIO_BIAS_HIGH: the GPIO will be wired high, connected to VDD
+ * GPIO_BIAS_GROUND: the GPIO will be grounded, connected to GROUND
+ */
+#define GPIO_CONFIG_BIAS_UNKNOWN 0x1000
+#define GPIO_CONFIG_BIAS_FLOAT 0x1001
+#define GPIO_CONFIG_BIAS_PULL_UP 0x1002
+#define GPIO_CONFIG_BIAS_PULL_DOWN 0x1003
+#define GPIO_CONFIG_BIAS_HIGH 0x1004
+#define GPIO_CONFIG_BIAS_GROUND 0x1005
+
+/*
+ * Drive modes for GPIOs (output) - if you have more custom modes either
+ * add them here or keep them to your driver if you think they are not
+ * generally useful.
+ *
+ * GPIO_CONFIG_DRIVE_UNKNOWN: we don't know the drive mode of this GPIO, for
+ * example since it is controlled by hardware or the information is not
+ * accessible but we need a meaningful enumerator in e.g. initialization
+ * code
+ * GPIO_CONFIG_DRIVE_PUSH_PULL: the GPIO will be driven actively high and
+ * low, this is the most typical case and is typically achieved with two
+ * active transistors on the output
+ * GPIO_CONFIG_DRIVE_OPEN_DRAIN: the GPIO will be driven with open drain (open
+ * collector) which means it is usually wired with other output ports
+ * which are then pulled up with an external resistor
+ * GPIO_CONFIG_DRIVE_OPEN_SOURCE: the GPIO will be driven with open drain
+ * (open emitter) which is the same as open drain mutatis mutandis but
+ * pulled to ground
+ * GPIO_CONFIG_DRIVE_OFF: the GPIO pin is set to inactive mode, off
+ */
+#define GPIO_CONFIG_DRIVE_UNKNOWN 0x2010
+#define GPIO_CONFIG_DRIVE_PUSH_PULL 0x2011
+#define GPIO_CONFIG_DRIVE_OPEN_DRAIN 0x2012
+#define GPIO_CONFIG_DRIVE_OPEN_SOURCE 0x2013
+#define GPIO_CONFIG_DRIVE_OFF 0x2014
+
+int u300_gpio_set_config(unsigned gpio, u16 param, unsigned long *data);
--
1.7.3.2
More information about the linux-arm-kernel
mailing list