[PATCH v4 2/2] gpio/mxc: Change gpio-mxc into an upstanding gpio driver
Grant Likely
grant.likely at secretlab.ca
Mon Jun 6 03:52:41 EDT 2011
On Mon, Jun 06, 2011 at 12:07:55AM +0800, Shawn Guo wrote:
> The patch makes necessary changes on gpio-mxc as below to turn it
> into an upstanding gpio driver.
>
> * Add a list to save all mx2 ports references, so that
> mx2_gpio_irq_handler can walk through all interrupt status
> registers
>
> * Use readl/writel to replace mach-specific accessors
> __raw_readl/__raw_writel
>
> * Change mxc_gpio_init into mxc_gpio_probe function
>
> * Move "struct mxc_gpio_port" into gpio-mxc.c, as it needs not to
> be public at all, and also make some other cleanup on
> plat-mxc/include/mach/gpio.h at the same time
>
> And the patch then migrates mach-imx and mach-mx5 to the updated
> driver by adding corresponding platform devices.
>
> Signed-off-by: Shawn Guo <shawn.guo at linaro.org>
> Acked-by: Olof Johansson <olof at lixom.net>
Applied, thanks.
g.
> ---
> arch/arm/mach-imx/mach-apf9328.c | 2 +
> arch/arm/mach-imx/mach-armadillo5x0.c | 2 +
> arch/arm/mach-imx/mach-bug.c | 2 +
> arch/arm/mach-imx/mach-cpuimx27.c | 2 +
> arch/arm/mach-imx/mach-cpuimx35.c | 2 +
> arch/arm/mach-imx/mach-eukrea_cpuimx25.c | 2 +
> arch/arm/mach-imx/mach-imx27_visstrim_m10.c | 2 +
> arch/arm/mach-imx/mach-imx27ipcam.c | 2 +
> arch/arm/mach-imx/mach-imx27lite.c | 2 +
> arch/arm/mach-imx/mach-kzm_arm11_01.c | 2 +
> arch/arm/mach-imx/mach-mx1ads.c | 2 +
> arch/arm/mach-imx/mach-mx21ads.c | 2 +
> arch/arm/mach-imx/mach-mx25_3ds.c | 2 +
> arch/arm/mach-imx/mach-mx27_3ds.c | 2 +
> arch/arm/mach-imx/mach-mx27ads.c | 2 +
> arch/arm/mach-imx/mach-mx31_3ds.c | 2 +
> arch/arm/mach-imx/mach-mx31ads.c | 2 +
> arch/arm/mach-imx/mach-mx31lilly.c | 2 +
> arch/arm/mach-imx/mach-mx31lite.c | 2 +
> arch/arm/mach-imx/mach-mx31moboard.c | 2 +
> arch/arm/mach-imx/mach-mx35_3ds.c | 2 +
> arch/arm/mach-imx/mach-mxt_td60.c | 2 +
> arch/arm/mach-imx/mach-pca100.c | 2 +
> arch/arm/mach-imx/mach-pcm037.c | 2 +
> arch/arm/mach-imx/mach-pcm038.c | 2 +
> arch/arm/mach-imx/mach-pcm043.c | 2 +
> arch/arm/mach-imx/mach-qong.c | 2 +
> arch/arm/mach-imx/mach-scb9328.c | 2 +
> arch/arm/mach-imx/mach-vpr200.c | 2 +
> arch/arm/mach-imx/mm-imx1.c | 17 +-
> arch/arm/mach-imx/mm-imx21.c | 21 +--
> arch/arm/mach-imx/mm-imx25.c | 16 +-
> arch/arm/mach-imx/mm-imx27.c | 21 +--
> arch/arm/mach-imx/mm-imx31.c | 15 +-
> arch/arm/mach-imx/mm-imx35.c | 15 +-
> arch/arm/mach-mx5/board-cpuimx51.c | 2 +
> arch/arm/mach-mx5/board-cpuimx51sd.c | 2 +
> arch/arm/mach-mx5/board-mx50_rdp.c | 2 +
> arch/arm/mach-mx5/board-mx51_3ds.c | 2 +
> arch/arm/mach-mx5/board-mx51_babbage.c | 2 +
> arch/arm/mach-mx5/board-mx51_efikamx.c | 2 +
> arch/arm/mach-mx5/board-mx51_efikasb.c | 2 +
> arch/arm/mach-mx5/board-mx53_evk.c | 2 +
> arch/arm/mach-mx5/board-mx53_loco.c | 2 +
> arch/arm/mach-mx5/board-mx53_smd.c | 2 +
> arch/arm/mach-mx5/devices.c | 64 -------
> arch/arm/mach-mx5/mm-mx50.c | 21 +--
> arch/arm/mach-mx5/mm.c | 25 ++-
> arch/arm/plat-mxc/devices.c | 11 ++
> arch/arm/plat-mxc/devices/Makefile | 1 +
> arch/arm/plat-mxc/devices/platform-gpio-mxc.c | 32 ++++
> arch/arm/plat-mxc/include/mach/common.h | 12 ++-
> arch/arm/plat-mxc/include/mach/devices-common.h | 2 +
> arch/arm/plat-mxc/include/mach/gpio.h | 27 ---
> drivers/gpio/gpio-mxc.c | 217 +++++++++++++++--------
> 55 files changed, 358 insertions(+), 237 deletions(-)
> create mode 100644 arch/arm/plat-mxc/devices/platform-gpio-mxc.c
>
> diff --git a/arch/arm/mach-imx/mach-apf9328.c b/arch/arm/mach-imx/mach-apf9328.c
> index 15e45c8..59d2a3b 100644
> --- a/arch/arm/mach-imx/mach-apf9328.c
> +++ b/arch/arm/mach-imx/mach-apf9328.c
> @@ -115,6 +115,8 @@ static struct platform_device *devices[] __initdata = {
>
> static void __init apf9328_init(void)
> {
> + imx1_soc_init();
> +
> mxc_gpio_setup_multiple_pins(apf9328_pins,
> ARRAY_SIZE(apf9328_pins),
> "APF9328");
> diff --git a/arch/arm/mach-imx/mach-armadillo5x0.c b/arch/arm/mach-imx/mach-armadillo5x0.c
> index ffb40ff..ede2710 100644
> --- a/arch/arm/mach-imx/mach-armadillo5x0.c
> +++ b/arch/arm/mach-imx/mach-armadillo5x0.c
> @@ -490,6 +490,8 @@ static struct platform_device *devices[] __initdata = {
> */
> static void __init armadillo5x0_init(void)
> {
> + imx31_soc_init();
> +
> mxc_iomux_setup_multiple_pins(armadillo5x0_pins,
> ARRAY_SIZE(armadillo5x0_pins), "armadillo5x0");
>
> diff --git a/arch/arm/mach-imx/mach-bug.c b/arch/arm/mach-imx/mach-bug.c
> index 42e4f07..f494705 100644
> --- a/arch/arm/mach-imx/mach-bug.c
> +++ b/arch/arm/mach-imx/mach-bug.c
> @@ -42,6 +42,8 @@ static const unsigned int bug_pins[] __initconst = {
>
> static void __init bug_board_init(void)
> {
> + imx31_soc_init();
> +
> mxc_iomux_setup_multiple_pins(bug_pins,
> ARRAY_SIZE(bug_pins), "uart-4");
> imx31_add_imx_uart4(&uart_pdata);
> diff --git a/arch/arm/mach-imx/mach-cpuimx27.c b/arch/arm/mach-imx/mach-cpuimx27.c
> index 46a2e41..87887ac 100644
> --- a/arch/arm/mach-imx/mach-cpuimx27.c
> +++ b/arch/arm/mach-imx/mach-cpuimx27.c
> @@ -250,6 +250,8 @@ __setup("otg_mode=", eukrea_cpuimx27_otg_mode);
>
> static void __init eukrea_cpuimx27_init(void)
> {
> + imx27_soc_init();
> +
> mxc_gpio_setup_multiple_pins(eukrea_cpuimx27_pins,
> ARRAY_SIZE(eukrea_cpuimx27_pins), "CPUIMX27");
>
> diff --git a/arch/arm/mach-imx/mach-cpuimx35.c b/arch/arm/mach-imx/mach-cpuimx35.c
> index 3f8ef82..f39a478b 100644
> --- a/arch/arm/mach-imx/mach-cpuimx35.c
> +++ b/arch/arm/mach-imx/mach-cpuimx35.c
> @@ -156,6 +156,8 @@ __setup("otg_mode=", eukrea_cpuimx35_otg_mode);
> */
> static void __init eukrea_cpuimx35_init(void)
> {
> + imx35_soc_init();
> +
> mxc_iomux_v3_setup_multiple_pads(eukrea_cpuimx35_pads,
> ARRAY_SIZE(eukrea_cpuimx35_pads));
>
> diff --git a/arch/arm/mach-imx/mach-eukrea_cpuimx25.c b/arch/arm/mach-imx/mach-eukrea_cpuimx25.c
> index 148cff2..da36da5 100644
> --- a/arch/arm/mach-imx/mach-eukrea_cpuimx25.c
> +++ b/arch/arm/mach-imx/mach-eukrea_cpuimx25.c
> @@ -125,6 +125,8 @@ __setup("otg_mode=", eukrea_cpuimx25_otg_mode);
>
> static void __init eukrea_cpuimx25_init(void)
> {
> + imx25_soc_init();
> +
> if (mxc_iomux_v3_setup_multiple_pads(eukrea_cpuimx25_pads,
> ARRAY_SIZE(eukrea_cpuimx25_pads)))
> printk(KERN_ERR "error setting cpuimx25 pads !\n");
> diff --git a/arch/arm/mach-imx/mach-imx27_visstrim_m10.c b/arch/arm/mach-imx/mach-imx27_visstrim_m10.c
> index 7ae43b1..c6269d6 100644
> --- a/arch/arm/mach-imx/mach-imx27_visstrim_m10.c
> +++ b/arch/arm/mach-imx/mach-imx27_visstrim_m10.c
> @@ -231,6 +231,8 @@ static void __init visstrim_m10_board_init(void)
> {
> int ret;
>
> + imx27_soc_init();
> +
> ret = mxc_gpio_setup_multiple_pins(visstrim_m10_pins,
> ARRAY_SIZE(visstrim_m10_pins), "VISSTRIM_M10");
> if (ret)
> diff --git a/arch/arm/mach-imx/mach-imx27ipcam.c b/arch/arm/mach-imx/mach-imx27ipcam.c
> index 9be6cd6..272f793 100644
> --- a/arch/arm/mach-imx/mach-imx27ipcam.c
> +++ b/arch/arm/mach-imx/mach-imx27ipcam.c
> @@ -50,6 +50,8 @@ static const int mx27ipcam_pins[] __initconst = {
>
> static void __init mx27ipcam_init(void)
> {
> + imx27_soc_init();
> +
> mxc_gpio_setup_multiple_pins(mx27ipcam_pins, ARRAY_SIZE(mx27ipcam_pins),
> "mx27ipcam");
>
> diff --git a/arch/arm/mach-imx/mach-imx27lite.c b/arch/arm/mach-imx/mach-imx27lite.c
> index 8411405..d81a769 100644
> --- a/arch/arm/mach-imx/mach-imx27lite.c
> +++ b/arch/arm/mach-imx/mach-imx27lite.c
> @@ -59,6 +59,8 @@ static const struct imxuart_platform_data uart_pdata __initconst = {
>
> static void __init mx27lite_init(void)
> {
> + imx27_soc_init();
> +
> mxc_gpio_setup_multiple_pins(mx27lite_pins, ARRAY_SIZE(mx27lite_pins),
> "imx27lite");
> imx27_add_imx_uart0(&uart_pdata);
> diff --git a/arch/arm/mach-imx/mach-kzm_arm11_01.c b/arch/arm/mach-imx/mach-kzm_arm11_01.c
> index 1ecae20..e472a1d 100644
> --- a/arch/arm/mach-imx/mach-kzm_arm11_01.c
> +++ b/arch/arm/mach-imx/mach-kzm_arm11_01.c
> @@ -223,6 +223,8 @@ static int kzm_pins[] __initdata = {
> */
> static void __init kzm_board_init(void)
> {
> + imx31_soc_init();
> +
> mxc_iomux_setup_multiple_pins(kzm_pins,
> ARRAY_SIZE(kzm_pins), "kzm");
> kzm_init_ext_uart();
> diff --git a/arch/arm/mach-imx/mach-mx1ads.c b/arch/arm/mach-imx/mach-mx1ads.c
> index 38ec5cb..5cd8bee 100644
> --- a/arch/arm/mach-imx/mach-mx1ads.c
> +++ b/arch/arm/mach-imx/mach-mx1ads.c
> @@ -115,6 +115,8 @@ static struct i2c_board_info mx1ads_i2c_devices[] = {
> */
> static void __init mx1ads_init(void)
> {
> + imx1_soc_init();
> +
> mxc_gpio_setup_multiple_pins(mx1ads_pins,
> ARRAY_SIZE(mx1ads_pins), "mx1ads");
>
> diff --git a/arch/arm/mach-imx/mach-mx21ads.c b/arch/arm/mach-imx/mach-mx21ads.c
> index 74ac889..d389ecf 100644
> --- a/arch/arm/mach-imx/mach-mx21ads.c
> +++ b/arch/arm/mach-imx/mach-mx21ads.c
> @@ -279,6 +279,8 @@ static struct platform_device *platform_devices[] __initdata = {
>
> static void __init mx21ads_board_init(void)
> {
> + imx21_soc_init();
> +
> mxc_gpio_setup_multiple_pins(mx21ads_pins, ARRAY_SIZE(mx21ads_pins),
> "mx21ads");
>
> diff --git a/arch/arm/mach-imx/mach-mx25_3ds.c b/arch/arm/mach-imx/mach-mx25_3ds.c
> index 58ea3fd..01534bb 100644
> --- a/arch/arm/mach-imx/mach-mx25_3ds.c
> +++ b/arch/arm/mach-imx/mach-mx25_3ds.c
> @@ -219,6 +219,8 @@ static const struct esdhc_platform_data mx25pdk_esdhc_pdata __initconst = {
>
> static void __init mx25pdk_init(void)
> {
> + imx25_soc_init();
> +
> mxc_iomux_v3_setup_multiple_pads(mx25pdk_pads,
> ARRAY_SIZE(mx25pdk_pads));
>
> diff --git a/arch/arm/mach-imx/mach-mx27_3ds.c b/arch/arm/mach-imx/mach-mx27_3ds.c
> index 6e1accf..117ce0a 100644
> --- a/arch/arm/mach-imx/mach-mx27_3ds.c
> +++ b/arch/arm/mach-imx/mach-mx27_3ds.c
> @@ -267,6 +267,8 @@ static const struct imxi2c_platform_data mx27_3ds_i2c0_data __initconst = {
>
> static void __init mx27pdk_init(void)
> {
> + imx27_soc_init();
> +
> mxc_gpio_setup_multiple_pins(mx27pdk_pins, ARRAY_SIZE(mx27pdk_pins),
> "mx27pdk");
> mx27_3ds_sdhc1_enable_level_translator();
> diff --git a/arch/arm/mach-imx/mach-mx27ads.c b/arch/arm/mach-imx/mach-mx27ads.c
> index 1db7950..fc26ed7 100644
> --- a/arch/arm/mach-imx/mach-mx27ads.c
> +++ b/arch/arm/mach-imx/mach-mx27ads.c
> @@ -288,6 +288,8 @@ static const struct imxuart_platform_data uart_pdata __initconst = {
>
> static void __init mx27ads_board_init(void)
> {
> + imx27_soc_init();
> +
> mxc_gpio_setup_multiple_pins(mx27ads_pins, ARRAY_SIZE(mx27ads_pins),
> "mx27ads");
>
> diff --git a/arch/arm/mach-imx/mach-mx31_3ds.c b/arch/arm/mach-imx/mach-mx31_3ds.c
> index 9b98244..ab2a626 100644
> --- a/arch/arm/mach-imx/mach-mx31_3ds.c
> +++ b/arch/arm/mach-imx/mach-mx31_3ds.c
> @@ -689,6 +689,8 @@ static void __init mx31_3ds_init(void)
> {
> int ret;
>
> + imx31_soc_init();
> +
> mxc_iomux_setup_multiple_pins(mx31_3ds_pins, ARRAY_SIZE(mx31_3ds_pins),
> "mx31_3ds");
>
> diff --git a/arch/arm/mach-imx/mach-mx31ads.c b/arch/arm/mach-imx/mach-mx31ads.c
> index f4dee02..0ce4947 100644
> --- a/arch/arm/mach-imx/mach-mx31ads.c
> +++ b/arch/arm/mach-imx/mach-mx31ads.c
> @@ -516,6 +516,8 @@ static void __init mx31ads_init_irq(void)
>
> static void __init mx31ads_init(void)
> {
> + imx31_soc_init();
> +
> mxc_init_extuart();
> mxc_init_imx_uart();
> mxc_init_i2c();
> diff --git a/arch/arm/mach-imx/mach-mx31lilly.c b/arch/arm/mach-imx/mach-mx31lilly.c
> index 410e676..750368d 100644
> --- a/arch/arm/mach-imx/mach-mx31lilly.c
> +++ b/arch/arm/mach-imx/mach-mx31lilly.c
> @@ -243,6 +243,8 @@ core_param(mx31lilly_baseboard, mx31lilly_baseboard, int, 0444);
>
> static void __init mx31lilly_board_init(void)
> {
> + imx31_soc_init();
> +
> switch (mx31lilly_baseboard) {
> case MX31LILLY_NOBOARD:
> break;
> diff --git a/arch/arm/mach-imx/mach-mx31lite.c b/arch/arm/mach-imx/mach-mx31lite.c
> index ac9b4ca..4b47fd9 100644
> --- a/arch/arm/mach-imx/mach-mx31lite.c
> +++ b/arch/arm/mach-imx/mach-mx31lite.c
> @@ -230,6 +230,8 @@ static void __init mx31lite_init(void)
> {
> int ret;
>
> + imx31_soc_init();
> +
> switch (mx31lite_baseboard) {
> case MX31LITE_NOBOARD:
> break;
> diff --git a/arch/arm/mach-imx/mach-mx31moboard.c b/arch/arm/mach-imx/mach-mx31moboard.c
> index eaa51e4..a52fd36 100644
> --- a/arch/arm/mach-imx/mach-mx31moboard.c
> +++ b/arch/arm/mach-imx/mach-mx31moboard.c
> @@ -507,6 +507,8 @@ core_param(mx31moboard_baseboard, mx31moboard_baseboard, int, 0444);
> */
> static void __init mx31moboard_init(void)
> {
> + imx31_soc_init();
> +
> mxc_iomux_setup_multiple_pins(moboard_pins, ARRAY_SIZE(moboard_pins),
> "moboard");
>
> diff --git a/arch/arm/mach-imx/mach-mx35_3ds.c b/arch/arm/mach-imx/mach-mx35_3ds.c
> index 882880a..48b3c6f 100644
> --- a/arch/arm/mach-imx/mach-mx35_3ds.c
> +++ b/arch/arm/mach-imx/mach-mx35_3ds.c
> @@ -179,6 +179,8 @@ static const struct imxi2c_platform_data mx35_3ds_i2c0_data __initconst = {
> */
> static void __init mx35_3ds_init(void)
> {
> + imx35_soc_init();
> +
> mxc_iomux_v3_setup_multiple_pads(mx35pdk_pads, ARRAY_SIZE(mx35pdk_pads));
>
> imx35_add_fec(NULL);
> diff --git a/arch/arm/mach-imx/mach-mxt_td60.c b/arch/arm/mach-imx/mach-mxt_td60.c
> index 2774541..c85876f 100644
> --- a/arch/arm/mach-imx/mach-mxt_td60.c
> +++ b/arch/arm/mach-imx/mach-mxt_td60.c
> @@ -233,6 +233,8 @@ static const struct imxuart_platform_data uart_pdata __initconst = {
>
> static void __init mxt_td60_board_init(void)
> {
> + imx27_soc_init();
> +
> mxc_gpio_setup_multiple_pins(mxt_td60_pins, ARRAY_SIZE(mxt_td60_pins),
> "MXT_TD60");
>
> diff --git a/arch/arm/mach-imx/mach-pca100.c b/arch/arm/mach-imx/mach-pca100.c
> index bbddc5a..71083aa 100644
> --- a/arch/arm/mach-imx/mach-pca100.c
> +++ b/arch/arm/mach-imx/mach-pca100.c
> @@ -357,6 +357,8 @@ static void __init pca100_init(void)
> {
> int ret;
>
> + imx27_soc_init();
> +
> /* SSI unit */
> mxc_audmux_v1_configure_port(MX27_AUDMUX_HPCR1_SSI0,
> MXC_AUDMUX_V1_PCR_SYN | /* 4wire mode */
> diff --git a/arch/arm/mach-imx/mach-pcm037.c b/arch/arm/mach-imx/mach-pcm037.c
> index 89c213b..f45b7cd 100644
> --- a/arch/arm/mach-imx/mach-pcm037.c
> +++ b/arch/arm/mach-imx/mach-pcm037.c
> @@ -576,6 +576,8 @@ static void __init pcm037_init(void)
> {
> int ret;
>
> + imx31_soc_init();
> +
> mxc_iomux_set_gpr(MUX_PGP_UH2, 1);
>
> mxc_iomux_setup_multiple_pins(pcm037_pins, ARRAY_SIZE(pcm037_pins),
> diff --git a/arch/arm/mach-imx/mach-pcm038.c b/arch/arm/mach-imx/mach-pcm038.c
> index 853bb87..2d6a64b 100644
> --- a/arch/arm/mach-imx/mach-pcm038.c
> +++ b/arch/arm/mach-imx/mach-pcm038.c
> @@ -295,6 +295,8 @@ static const struct mxc_usbh_platform_data usbh2_pdata __initconst = {
>
> static void __init pcm038_init(void)
> {
> + imx27_soc_init();
> +
> mxc_gpio_setup_multiple_pins(pcm038_pins, ARRAY_SIZE(pcm038_pins),
> "PCM038");
>
> diff --git a/arch/arm/mach-imx/mach-pcm043.c b/arch/arm/mach-imx/mach-pcm043.c
> index 0264416..163cc31 100644
> --- a/arch/arm/mach-imx/mach-pcm043.c
> +++ b/arch/arm/mach-imx/mach-pcm043.c
> @@ -356,6 +356,8 @@ static struct esdhc_platform_data sd1_pdata = {
> */
> static void __init pcm043_init(void)
> {
> + imx35_soc_init();
> +
> mxc_iomux_v3_setup_multiple_pads(pcm043_pads, ARRAY_SIZE(pcm043_pads));
>
> mxc_audmux_v2_configure_port(3,
> diff --git a/arch/arm/mach-imx/mach-qong.c b/arch/arm/mach-imx/mach-qong.c
> index c163287..3626f48 100644
> --- a/arch/arm/mach-imx/mach-qong.c
> +++ b/arch/arm/mach-imx/mach-qong.c
> @@ -244,6 +244,8 @@ static void __init qong_init_fpga(void)
> */
> static void __init qong_init(void)
> {
> + imx31_soc_init();
> +
> mxc_init_imx_uart();
> qong_init_nor_mtd();
> qong_init_fpga();
> diff --git a/arch/arm/mach-imx/mach-scb9328.c b/arch/arm/mach-imx/mach-scb9328.c
> index dcaee04..8280526 100644
> --- a/arch/arm/mach-imx/mach-scb9328.c
> +++ b/arch/arm/mach-imx/mach-scb9328.c
> @@ -129,6 +129,8 @@ static struct platform_device *devices[] __initdata = {
> */
> static void __init scb9328_init(void)
> {
> + imx1_soc_init();
> +
> imx1_add_imx_uart0(&uart_pdata);
>
> printk(KERN_INFO"Scb9328: Adding devices\n");
> diff --git a/arch/arm/mach-imx/mach-vpr200.c b/arch/arm/mach-imx/mach-vpr200.c
> index d74e347..7d8e012 100644
> --- a/arch/arm/mach-imx/mach-vpr200.c
> +++ b/arch/arm/mach-imx/mach-vpr200.c
> @@ -267,6 +267,8 @@ static struct platform_device *devices[] __initdata = {
> */
> static void __init vpr200_board_init(void)
> {
> + imx35_soc_init();
> +
> mxc_iomux_v3_setup_multiple_pads(vpr200_pads, ARRAY_SIZE(vpr200_pads));
>
> imx35_add_fec(NULL);
> diff --git a/arch/arm/mach-imx/mm-imx1.c b/arch/arm/mach-imx/mm-imx1.c
> index 2e482ba..b486595 100644
> --- a/arch/arm/mach-imx/mm-imx1.c
> +++ b/arch/arm/mach-imx/mm-imx1.c
> @@ -23,7 +23,6 @@
>
> #include <mach/common.h>
> #include <mach/hardware.h>
> -#include <mach/gpio.h>
> #include <mach/irqs.h>
> #include <mach/iomux-v1.h>
>
> @@ -44,15 +43,15 @@ void __init imx1_init_early(void)
> MX1_NUM_GPIO_PORT);
> }
>
> -static struct mxc_gpio_port imx1_gpio_ports[] = {
> - DEFINE_IMX_GPIO_PORT_IRQ(MX1, 0, 1, MX1_GPIO_INT_PORTA),
> - DEFINE_IMX_GPIO_PORT_IRQ(MX1, 1, 2, MX1_GPIO_INT_PORTB),
> - DEFINE_IMX_GPIO_PORT_IRQ(MX1, 2, 3, MX1_GPIO_INT_PORTC),
> - DEFINE_IMX_GPIO_PORT_IRQ(MX1, 3, 4, MX1_GPIO_INT_PORTD),
> -};
> -
> void __init mx1_init_irq(void)
> {
> mxc_init_irq(MX1_IO_ADDRESS(MX1_AVIC_BASE_ADDR));
> - mxc_gpio_init(imx1_gpio_ports, ARRAY_SIZE(imx1_gpio_ports));
> +}
> +
> +void __init imx1_soc_init(void)
> +{
> + mxc_register_gpio(0, MX1_GPIO1_BASE_ADDR, SZ_4K, MX1_GPIO_INT_PORTA, 0);
> + mxc_register_gpio(1, MX1_GPIO2_BASE_ADDR, SZ_4K, MX1_GPIO_INT_PORTB, 0);
> + mxc_register_gpio(2, MX1_GPIO3_BASE_ADDR, SZ_4K, MX1_GPIO_INT_PORTC, 0);
> + mxc_register_gpio(3, MX1_GPIO4_BASE_ADDR, SZ_4K, MX1_GPIO_INT_PORTD, 0);
> }
> diff --git a/arch/arm/mach-imx/mm-imx21.c b/arch/arm/mach-imx/mm-imx21.c
> index 7a0c500..f0fb8bc 100644
> --- a/arch/arm/mach-imx/mm-imx21.c
> +++ b/arch/arm/mach-imx/mm-imx21.c
> @@ -24,7 +24,6 @@
> #include <mach/common.h>
> #include <asm/pgtable.h>
> #include <asm/mach/map.h>
> -#include <mach/gpio.h>
> #include <mach/irqs.h>
> #include <mach/iomux-v1.h>
>
> @@ -70,17 +69,17 @@ void __init imx21_init_early(void)
> MX21_NUM_GPIO_PORT);
> }
>
> -static struct mxc_gpio_port imx21_gpio_ports[] = {
> - DEFINE_IMX_GPIO_PORT_IRQ(MX21, 0, 1, MX21_INT_GPIO),
> - DEFINE_IMX_GPIO_PORT(MX21, 1, 2),
> - DEFINE_IMX_GPIO_PORT(MX21, 2, 3),
> - DEFINE_IMX_GPIO_PORT(MX21, 3, 4),
> - DEFINE_IMX_GPIO_PORT(MX21, 4, 5),
> - DEFINE_IMX_GPIO_PORT(MX21, 5, 6),
> -};
> -
> void __init mx21_init_irq(void)
> {
> mxc_init_irq(MX21_IO_ADDRESS(MX21_AVIC_BASE_ADDR));
> - mxc_gpio_init(imx21_gpio_ports, ARRAY_SIZE(imx21_gpio_ports));
> +}
> +
> +void __init imx21_soc_init(void)
> +{
> + mxc_register_gpio(0, MX21_GPIO1_BASE_ADDR, SZ_4K, MX21_INT_GPIO, 0);
> + mxc_register_gpio(1, MX21_GPIO2_BASE_ADDR, SZ_4K, MX21_INT_GPIO, 0);
> + mxc_register_gpio(2, MX21_GPIO3_BASE_ADDR, SZ_4K, MX21_INT_GPIO, 0);
> + mxc_register_gpio(3, MX21_GPIO4_BASE_ADDR, SZ_4K, MX21_INT_GPIO, 0);
> + mxc_register_gpio(4, MX21_GPIO5_BASE_ADDR, SZ_4K, MX21_INT_GPIO, 0);
> + mxc_register_gpio(5, MX21_GPIO6_BASE_ADDR, SZ_4K, MX21_INT_GPIO, 0);
> }
> diff --git a/arch/arm/mach-imx/mm-imx25.c b/arch/arm/mach-imx/mm-imx25.c
> index 02f7b5c..1b6d583 100644
> --- a/arch/arm/mach-imx/mm-imx25.c
> +++ b/arch/arm/mach-imx/mm-imx25.c
> @@ -27,7 +27,6 @@
> #include <mach/hardware.h>
> #include <mach/mx25.h>
> #include <mach/iomux-v3.h>
> -#include <mach/gpio.h>
> #include <mach/irqs.h>
>
> /*
> @@ -57,16 +56,15 @@ void __init imx25_init_early(void)
> mxc_arch_reset_init(MX25_IO_ADDRESS(MX25_WDOG_BASE_ADDR));
> }
>
> -static struct mxc_gpio_port imx25_gpio_ports[] = {
> - DEFINE_IMX_GPIO_PORT_IRQ(MX25, 0, 1, MX25_INT_GPIO1),
> - DEFINE_IMX_GPIO_PORT_IRQ(MX25, 1, 2, MX25_INT_GPIO2),
> - DEFINE_IMX_GPIO_PORT_IRQ(MX25, 2, 3, MX25_INT_GPIO3),
> - DEFINE_IMX_GPIO_PORT_IRQ(MX25, 3, 4, MX25_INT_GPIO4),
> -};
> -
> void __init mx25_init_irq(void)
> {
> mxc_init_irq(MX25_IO_ADDRESS(MX25_AVIC_BASE_ADDR));
> - mxc_gpio_init(imx25_gpio_ports, ARRAY_SIZE(imx25_gpio_ports));
> }
>
> +void __init imx25_soc_init(void)
> +{
> + mxc_register_gpio(0, MX25_GPIO1_BASE_ADDR, SZ_16K, MX25_INT_GPIO1, 0);
> + mxc_register_gpio(1, MX25_GPIO2_BASE_ADDR, SZ_16K, MX25_INT_GPIO2, 0);
> + mxc_register_gpio(2, MX25_GPIO3_BASE_ADDR, SZ_16K, MX25_INT_GPIO3, 0);
> + mxc_register_gpio(3, MX25_GPIO4_BASE_ADDR, SZ_16K, MX25_INT_GPIO4, 0);
> +}
> diff --git a/arch/arm/mach-imx/mm-imx27.c b/arch/arm/mach-imx/mm-imx27.c
> index a6761a3..d3700ce 100644
> --- a/arch/arm/mach-imx/mm-imx27.c
> +++ b/arch/arm/mach-imx/mm-imx27.c
> @@ -24,7 +24,6 @@
> #include <mach/common.h>
> #include <asm/pgtable.h>
> #include <asm/mach/map.h>
> -#include <mach/gpio.h>
> #include <mach/irqs.h>
> #include <mach/iomux-v1.h>
>
> @@ -70,17 +69,17 @@ void __init imx27_init_early(void)
> MX27_NUM_GPIO_PORT);
> }
>
> -static struct mxc_gpio_port imx27_gpio_ports[] = {
> - DEFINE_IMX_GPIO_PORT_IRQ(MX27, 0, 1, MX27_INT_GPIO),
> - DEFINE_IMX_GPIO_PORT(MX27, 1, 2),
> - DEFINE_IMX_GPIO_PORT(MX27, 2, 3),
> - DEFINE_IMX_GPIO_PORT(MX27, 3, 4),
> - DEFINE_IMX_GPIO_PORT(MX27, 4, 5),
> - DEFINE_IMX_GPIO_PORT(MX27, 5, 6),
> -};
> -
> void __init mx27_init_irq(void)
> {
> mxc_init_irq(MX27_IO_ADDRESS(MX27_AVIC_BASE_ADDR));
> - mxc_gpio_init(imx27_gpio_ports, ARRAY_SIZE(imx27_gpio_ports));
> +}
> +
> +void __init imx27_soc_init(void)
> +{
> + mxc_register_gpio(0, MX27_GPIO1_BASE_ADDR, SZ_4K, MX27_INT_GPIO, 0);
> + mxc_register_gpio(1, MX27_GPIO2_BASE_ADDR, SZ_4K, MX27_INT_GPIO, 0);
> + mxc_register_gpio(2, MX27_GPIO3_BASE_ADDR, SZ_4K, MX27_INT_GPIO, 0);
> + mxc_register_gpio(3, MX27_GPIO4_BASE_ADDR, SZ_4K, MX27_INT_GPIO, 0);
> + mxc_register_gpio(4, MX27_GPIO5_BASE_ADDR, SZ_4K, MX27_INT_GPIO, 0);
> + mxc_register_gpio(5, MX27_GPIO6_BASE_ADDR, SZ_4K, MX27_INT_GPIO, 0);
> }
> diff --git a/arch/arm/mach-imx/mm-imx31.c b/arch/arm/mach-imx/mm-imx31.c
> index 86b9b45..cb16ac6 100644
> --- a/arch/arm/mach-imx/mm-imx31.c
> +++ b/arch/arm/mach-imx/mm-imx31.c
> @@ -26,7 +26,6 @@
> #include <mach/common.h>
> #include <mach/hardware.h>
> #include <mach/iomux-v3.h>
> -#include <mach/gpio.h>
> #include <mach/irqs.h>
>
> static struct map_desc mx31_io_desc[] __initdata = {
> @@ -53,14 +52,14 @@ void __init imx31_init_early(void)
> mxc_arch_reset_init(MX31_IO_ADDRESS(MX31_WDOG_BASE_ADDR));
> }
>
> -static struct mxc_gpio_port imx31_gpio_ports[] = {
> - DEFINE_IMX_GPIO_PORT_IRQ(MX31, 0, 1, MX31_INT_GPIO1),
> - DEFINE_IMX_GPIO_PORT_IRQ(MX31, 1, 2, MX31_INT_GPIO2),
> - DEFINE_IMX_GPIO_PORT_IRQ(MX31, 2, 3, MX31_INT_GPIO3),
> -};
> -
> void __init mx31_init_irq(void)
> {
> mxc_init_irq(MX31_IO_ADDRESS(MX31_AVIC_BASE_ADDR));
> - mxc_gpio_init(imx31_gpio_ports, ARRAY_SIZE(imx31_gpio_ports));
> +}
> +
> +void __init imx31_soc_init(void)
> +{
> + mxc_register_gpio(0, MX31_GPIO1_BASE_ADDR, SZ_16K, MX31_INT_GPIO1, 0);
> + mxc_register_gpio(1, MX31_GPIO2_BASE_ADDR, SZ_16K, MX31_INT_GPIO2, 0);
> + mxc_register_gpio(2, MX31_GPIO3_BASE_ADDR, SZ_16K, MX31_INT_GPIO3, 0);
> }
> diff --git a/arch/arm/mach-imx/mm-imx35.c b/arch/arm/mach-imx/mm-imx35.c
> index c880e6d..648bfca 100644
> --- a/arch/arm/mach-imx/mm-imx35.c
> +++ b/arch/arm/mach-imx/mm-imx35.c
> @@ -27,7 +27,6 @@
> #include <mach/common.h>
> #include <mach/hardware.h>
> #include <mach/iomux-v3.h>
> -#include <mach/gpio.h>
> #include <mach/irqs.h>
>
> static struct map_desc mx35_io_desc[] __initdata = {
> @@ -50,14 +49,14 @@ void __init imx35_init_early(void)
> mxc_arch_reset_init(MX35_IO_ADDRESS(MX35_WDOG_BASE_ADDR));
> }
>
> -static struct mxc_gpio_port imx35_gpio_ports[] = {
> - DEFINE_IMX_GPIO_PORT_IRQ(MX35, 0, 1, MX35_INT_GPIO1),
> - DEFINE_IMX_GPIO_PORT_IRQ(MX35, 1, 2, MX35_INT_GPIO2),
> - DEFINE_IMX_GPIO_PORT_IRQ(MX35, 2, 3, MX35_INT_GPIO3),
> -};
> -
> void __init mx35_init_irq(void)
> {
> mxc_init_irq(MX35_IO_ADDRESS(MX35_AVIC_BASE_ADDR));
> - mxc_gpio_init(imx35_gpio_ports, ARRAY_SIZE(imx35_gpio_ports));
> +}
> +
> +void __init imx35_soc_init(void)
> +{
> + mxc_register_gpio(0, MX35_GPIO1_BASE_ADDR, SZ_16K, MX35_INT_GPIO1, 0);
> + mxc_register_gpio(1, MX35_GPIO2_BASE_ADDR, SZ_16K, MX35_INT_GPIO2, 0);
> + mxc_register_gpio(2, MX35_GPIO3_BASE_ADDR, SZ_16K, MX35_INT_GPIO3, 0);
> }
> diff --git a/arch/arm/mach-mx5/board-cpuimx51.c b/arch/arm/mach-mx5/board-cpuimx51.c
> index 4efa02e..add0d42 100644
> --- a/arch/arm/mach-mx5/board-cpuimx51.c
> +++ b/arch/arm/mach-mx5/board-cpuimx51.c
> @@ -245,6 +245,8 @@ __setup("otg_mode=", eukrea_cpuimx51_otg_mode);
> */
> static void __init eukrea_cpuimx51_init(void)
> {
> + imx51_soc_init();
> +
> mxc_iomux_v3_setup_multiple_pads(eukrea_cpuimx51_pads,
> ARRAY_SIZE(eukrea_cpuimx51_pads));
>
> diff --git a/arch/arm/mach-mx5/board-cpuimx51sd.c b/arch/arm/mach-mx5/board-cpuimx51sd.c
> index 5ef25a5..ff096d5 100644
> --- a/arch/arm/mach-mx5/board-cpuimx51sd.c
> +++ b/arch/arm/mach-mx5/board-cpuimx51sd.c
> @@ -264,6 +264,8 @@ static struct platform_device *platform_devices[] __initdata = {
>
> static void __init eukrea_cpuimx51sd_init(void)
> {
> + imx51_soc_init();
> +
> mxc_iomux_v3_setup_multiple_pads(eukrea_cpuimx51sd_pads,
> ARRAY_SIZE(eukrea_cpuimx51sd_pads));
>
> diff --git a/arch/arm/mach-mx5/board-mx50_rdp.c b/arch/arm/mach-mx5/board-mx50_rdp.c
> index 11210e1..7de25c6 100644
> --- a/arch/arm/mach-mx5/board-mx50_rdp.c
> +++ b/arch/arm/mach-mx5/board-mx50_rdp.c
> @@ -192,6 +192,8 @@ static const struct imxi2c_platform_data i2c_data __initconst = {
> */
> static void __init mx50_rdp_board_init(void)
> {
> + imx50_soc_init();
> +
> mxc_iomux_v3_setup_multiple_pads(mx50_rdp_pads,
> ARRAY_SIZE(mx50_rdp_pads));
>
> diff --git a/arch/arm/mach-mx5/board-mx51_3ds.c b/arch/arm/mach-mx5/board-mx51_3ds.c
> index 63dfbea..3112d15 100644
> --- a/arch/arm/mach-mx5/board-mx51_3ds.c
> +++ b/arch/arm/mach-mx5/board-mx51_3ds.c
> @@ -135,6 +135,8 @@ static struct spi_board_info mx51_3ds_spi_nor_device[] = {
> */
> static void __init mx51_3ds_init(void)
> {
> + imx51_soc_init();
> +
> mxc_iomux_v3_setup_multiple_pads(mx51_3ds_pads,
> ARRAY_SIZE(mx51_3ds_pads));
>
> diff --git a/arch/arm/mach-mx5/board-mx51_babbage.c b/arch/arm/mach-mx5/board-mx51_babbage.c
> index c7b3fab..6021dd0 100644
> --- a/arch/arm/mach-mx5/board-mx51_babbage.c
> +++ b/arch/arm/mach-mx5/board-mx51_babbage.c
> @@ -340,6 +340,8 @@ static void __init mx51_babbage_init(void)
> iomux_v3_cfg_t power_key = _MX51_PAD_EIM_A27__GPIO2_21 |
> MUX_PAD_CTRL(PAD_CTL_SRE_FAST | PAD_CTL_DSE_HIGH | PAD_CTL_PUS_100K_UP);
>
> + imx51_soc_init();
> +
> #if defined(CONFIG_CPU_FREQ_IMX)
> get_cpu_op = mx51_get_cpu_op;
> #endif
> diff --git a/arch/arm/mach-mx5/board-mx51_efikamx.c b/arch/arm/mach-mx5/board-mx51_efikamx.c
> index 6e36231..3be603b 100644
> --- a/arch/arm/mach-mx5/board-mx51_efikamx.c
> +++ b/arch/arm/mach-mx5/board-mx51_efikamx.c
> @@ -236,6 +236,8 @@ late_initcall(mx51_efikamx_power_init);
>
> static void __init mx51_efikamx_init(void)
> {
> + imx51_soc_init();
> +
> mxc_iomux_v3_setup_multiple_pads(mx51efikamx_pads,
> ARRAY_SIZE(mx51efikamx_pads));
> efika_board_common_init();
> diff --git a/arch/arm/mach-mx5/board-mx51_efikasb.c b/arch/arm/mach-mx5/board-mx51_efikasb.c
> index 474fc6e..4b2e522 100644
> --- a/arch/arm/mach-mx5/board-mx51_efikasb.c
> +++ b/arch/arm/mach-mx5/board-mx51_efikasb.c
> @@ -248,6 +248,8 @@ static void __init mx51_efikasb_board_id(void)
>
> static void __init efikasb_board_init(void)
> {
> + imx51_soc_init();
> +
> mxc_iomux_v3_setup_multiple_pads(mx51efikasb_pads,
> ARRAY_SIZE(mx51efikasb_pads));
> efika_board_common_init();
> diff --git a/arch/arm/mach-mx5/board-mx53_evk.c b/arch/arm/mach-mx5/board-mx53_evk.c
> index f87d571..0d9218a 100644
> --- a/arch/arm/mach-mx5/board-mx53_evk.c
> +++ b/arch/arm/mach-mx5/board-mx53_evk.c
> @@ -117,6 +117,8 @@ static const struct spi_imx_master mx53_evk_spi_data __initconst = {
>
> static void __init mx53_evk_board_init(void)
> {
> + imx53_soc_init();
> +
> mxc_iomux_v3_setup_multiple_pads(mx53_evk_pads,
> ARRAY_SIZE(mx53_evk_pads));
> mx53_evk_init_uart();
> diff --git a/arch/arm/mach-mx5/board-mx53_loco.c b/arch/arm/mach-mx5/board-mx53_loco.c
> index 1b947e8..359c3e2 100644
> --- a/arch/arm/mach-mx5/board-mx53_loco.c
> +++ b/arch/arm/mach-mx5/board-mx53_loco.c
> @@ -227,6 +227,8 @@ static const struct imxi2c_platform_data mx53_loco_i2c_data __initconst = {
>
> static void __init mx53_loco_board_init(void)
> {
> + imx53_soc_init();
> +
> mxc_iomux_v3_setup_multiple_pads(mx53_loco_pads,
> ARRAY_SIZE(mx53_loco_pads));
> imx53_add_imx_uart(0, NULL);
> diff --git a/arch/arm/mach-mx5/board-mx53_smd.c b/arch/arm/mach-mx5/board-mx53_smd.c
> index 817c089..bc02894 100644
> --- a/arch/arm/mach-mx5/board-mx53_smd.c
> +++ b/arch/arm/mach-mx5/board-mx53_smd.c
> @@ -113,6 +113,8 @@ static const struct imxi2c_platform_data mx53_smd_i2c_data __initconst = {
>
> static void __init mx53_smd_board_init(void)
> {
> + imx53_soc_init();
> +
> mxc_iomux_v3_setup_multiple_pads(mx53_smd_pads,
> ARRAY_SIZE(mx53_smd_pads));
> mx53_smd_init_uart();
> diff --git a/arch/arm/mach-mx5/devices.c b/arch/arm/mach-mx5/devices.c
> index 153ada5..371ca8c 100644
> --- a/arch/arm/mach-mx5/devices.c
> +++ b/arch/arm/mach-mx5/devices.c
> @@ -12,7 +12,6 @@
>
> #include <linux/platform_device.h>
> #include <linux/dma-mapping.h>
> -#include <linux/gpio.h>
> #include <mach/hardware.h>
> #include <mach/imx-uart.h>
> #include <mach/irqs.h>
> @@ -119,66 +118,3 @@ struct platform_device mxc_usbh2_device = {
> .coherent_dma_mask = DMA_BIT_MASK(32),
> },
> };
> -
> -static struct mxc_gpio_port mxc_gpio_ports[] = {
> - {
> - .chip.label = "gpio-0",
> - .base = MX51_IO_ADDRESS(MX51_GPIO1_BASE_ADDR),
> - .irq = MX51_MXC_INT_GPIO1_LOW,
> - .irq_high = MX51_MXC_INT_GPIO1_HIGH,
> - .virtual_irq_start = MXC_GPIO_IRQ_START
> - },
> - {
> - .chip.label = "gpio-1",
> - .base = MX51_IO_ADDRESS(MX51_GPIO2_BASE_ADDR),
> - .irq = MX51_MXC_INT_GPIO2_LOW,
> - .irq_high = MX51_MXC_INT_GPIO2_HIGH,
> - .virtual_irq_start = MXC_GPIO_IRQ_START + 32 * 1
> - },
> - {
> - .chip.label = "gpio-2",
> - .base = MX51_IO_ADDRESS(MX51_GPIO3_BASE_ADDR),
> - .irq = MX51_MXC_INT_GPIO3_LOW,
> - .irq_high = MX51_MXC_INT_GPIO3_HIGH,
> - .virtual_irq_start = MXC_GPIO_IRQ_START + 32 * 2
> - },
> - {
> - .chip.label = "gpio-3",
> - .base = MX51_IO_ADDRESS(MX51_GPIO4_BASE_ADDR),
> - .irq = MX51_MXC_INT_GPIO4_LOW,
> - .irq_high = MX51_MXC_INT_GPIO4_HIGH,
> - .virtual_irq_start = MXC_GPIO_IRQ_START + 32 * 3
> - },
> - {
> - .chip.label = "gpio-4",
> - .base = MX53_IO_ADDRESS(MX53_GPIO5_BASE_ADDR),
> - .irq = MX53_INT_GPIO5_LOW,
> - .irq_high = MX53_INT_GPIO5_HIGH,
> - .virtual_irq_start = MXC_GPIO_IRQ_START + 32 * 4
> - },
> - {
> - .chip.label = "gpio-5",
> - .base = MX53_IO_ADDRESS(MX53_GPIO6_BASE_ADDR),
> - .irq = MX53_INT_GPIO6_LOW,
> - .irq_high = MX53_INT_GPIO6_HIGH,
> - .virtual_irq_start = MXC_GPIO_IRQ_START + 32 * 5
> - },
> - {
> - .chip.label = "gpio-6",
> - .base = MX53_IO_ADDRESS(MX53_GPIO7_BASE_ADDR),
> - .irq = MX53_INT_GPIO7_LOW,
> - .irq_high = MX53_INT_GPIO7_HIGH,
> - .virtual_irq_start = MXC_GPIO_IRQ_START + 32 * 6
> - },
> -};
> -
> -int __init imx51_register_gpios(void)
> -{
> - return mxc_gpio_init(mxc_gpio_ports, 4);
> -}
> -
> -int __init imx53_register_gpios(void)
> -{
> - return mxc_gpio_init(mxc_gpio_ports, ARRAY_SIZE(mxc_gpio_ports));
> -}
> -
> diff --git a/arch/arm/mach-mx5/mm-mx50.c b/arch/arm/mach-mx5/mm-mx50.c
> index b9c363b..28c3f60 100644
> --- a/arch/arm/mach-mx5/mm-mx50.c
> +++ b/arch/arm/mach-mx5/mm-mx50.c
> @@ -26,7 +26,6 @@
> #include <mach/hardware.h>
> #include <mach/common.h>
> #include <mach/iomux-v3.h>
> -#include <mach/gpio.h>
> #include <mach/irqs.h>
>
> /*
> @@ -56,17 +55,17 @@ void __init imx50_init_early(void)
> mxc_arch_reset_init(MX50_IO_ADDRESS(MX50_WDOG_BASE_ADDR));
> }
>
> -static struct mxc_gpio_port imx50_gpio_ports[] = {
> - DEFINE_IMX_GPIO_PORT_IRQ_HIGH(MX50, 0, 1, MX50_INT_GPIO1_LOW, MX50_INT_GPIO1_HIGH),
> - DEFINE_IMX_GPIO_PORT_IRQ_HIGH(MX50, 1, 2, MX50_INT_GPIO2_LOW, MX50_INT_GPIO2_HIGH),
> - DEFINE_IMX_GPIO_PORT_IRQ_HIGH(MX50, 2, 3, MX50_INT_GPIO3_LOW, MX50_INT_GPIO3_HIGH),
> - DEFINE_IMX_GPIO_PORT_IRQ_HIGH(MX50, 3, 4, MX50_INT_GPIO3_LOW, MX50_INT_GPIO3_HIGH),
> - DEFINE_IMX_GPIO_PORT_IRQ_HIGH(MX50, 4, 5, MX50_INT_GPIO3_LOW, MX50_INT_GPIO3_HIGH),
> - DEFINE_IMX_GPIO_PORT_IRQ_HIGH(MX50, 5, 6, MX50_INT_GPIO3_LOW, MX50_INT_GPIO3_HIGH),
> -};
> -
> void __init mx50_init_irq(void)
> {
> tzic_init_irq(MX50_IO_ADDRESS(MX50_TZIC_BASE_ADDR));
> - mxc_gpio_init(imx50_gpio_ports, ARRAY_SIZE(imx50_gpio_ports));
> +}
> +
> +void __init imx50_soc_init(void)
> +{
> + mxc_register_gpio(0, MX50_GPIO1_BASE_ADDR, SZ_16K, MX50_INT_GPIO1_LOW, MX50_INT_GPIO1_HIGH);
> + mxc_register_gpio(1, MX50_GPIO2_BASE_ADDR, SZ_16K, MX50_INT_GPIO2_LOW, MX50_INT_GPIO2_HIGH);
> + mxc_register_gpio(2, MX50_GPIO3_BASE_ADDR, SZ_16K, MX50_INT_GPIO3_LOW, MX50_INT_GPIO3_HIGH);
> + mxc_register_gpio(3, MX50_GPIO4_BASE_ADDR, SZ_16K, MX50_INT_GPIO4_LOW, MX50_INT_GPIO4_HIGH);
> + mxc_register_gpio(4, MX50_GPIO5_BASE_ADDR, SZ_16K, MX50_INT_GPIO5_LOW, MX50_INT_GPIO5_HIGH);
> + mxc_register_gpio(5, MX50_GPIO6_BASE_ADDR, SZ_16K, MX50_INT_GPIO6_LOW, MX50_INT_GPIO6_HIGH);
> }
> diff --git a/arch/arm/mach-mx5/mm.c b/arch/arm/mach-mx5/mm.c
> index ff55730..800bb8b2 100644
> --- a/arch/arm/mach-mx5/mm.c
> +++ b/arch/arm/mach-mx5/mm.c
> @@ -69,8 +69,6 @@ void __init imx53_init_early(void)
> mxc_arch_reset_init(MX53_IO_ADDRESS(MX53_WDOG1_BASE_ADDR));
> }
>
> -int imx51_register_gpios(void);
> -
> void __init mx51_init_irq(void)
> {
> unsigned long tzic_addr;
> @@ -86,11 +84,8 @@ void __init mx51_init_irq(void)
> panic("unable to map TZIC interrupt controller\n");
>
> tzic_init_irq(tzic_virt);
> - imx51_register_gpios();
> }
>
> -int imx53_register_gpios(void);
> -
> void __init mx53_init_irq(void)
> {
> unsigned long tzic_addr;
> @@ -103,5 +98,23 @@ void __init mx53_init_irq(void)
> panic("unable to map TZIC interrupt controller\n");
>
> tzic_init_irq(tzic_virt);
> - imx53_register_gpios();
> +}
> +
> +void __init imx51_soc_init(void)
> +{
> + mxc_register_gpio(0, MX51_GPIO1_BASE_ADDR, SZ_16K, MX51_MXC_INT_GPIO1_LOW, MX51_MXC_INT_GPIO1_HIGH);
> + mxc_register_gpio(1, MX51_GPIO2_BASE_ADDR, SZ_16K, MX51_MXC_INT_GPIO2_LOW, MX51_MXC_INT_GPIO2_HIGH);
> + mxc_register_gpio(2, MX51_GPIO3_BASE_ADDR, SZ_16K, MX51_MXC_INT_GPIO3_LOW, MX51_MXC_INT_GPIO3_HIGH);
> + mxc_register_gpio(3, MX51_GPIO4_BASE_ADDR, SZ_16K, MX51_MXC_INT_GPIO4_LOW, MX51_MXC_INT_GPIO4_HIGH);
> +}
> +
> +void __init imx53_soc_init(void)
> +{
> + mxc_register_gpio(0, MX53_GPIO1_BASE_ADDR, SZ_16K, MX53_INT_GPIO1_LOW, MX53_INT_GPIO1_HIGH);
> + mxc_register_gpio(1, MX53_GPIO2_BASE_ADDR, SZ_16K, MX53_INT_GPIO2_LOW, MX53_INT_GPIO2_HIGH);
> + mxc_register_gpio(2, MX53_GPIO3_BASE_ADDR, SZ_16K, MX53_INT_GPIO3_LOW, MX53_INT_GPIO3_HIGH);
> + mxc_register_gpio(3, MX53_GPIO4_BASE_ADDR, SZ_16K, MX53_INT_GPIO4_LOW, MX53_INT_GPIO4_HIGH);
> + mxc_register_gpio(4, MX53_GPIO5_BASE_ADDR, SZ_16K, MX53_INT_GPIO5_LOW, MX53_INT_GPIO5_HIGH);
> + mxc_register_gpio(5, MX53_GPIO6_BASE_ADDR, SZ_16K, MX53_INT_GPIO6_LOW, MX53_INT_GPIO6_HIGH);
> + mxc_register_gpio(6, MX53_GPIO7_BASE_ADDR, SZ_16K, MX53_INT_GPIO7_LOW, MX53_INT_GPIO7_HIGH);
> }
> diff --git a/arch/arm/plat-mxc/devices.c b/arch/arm/plat-mxc/devices.c
> index eee1b60..fb166b2 100644
> --- a/arch/arm/plat-mxc/devices.c
> +++ b/arch/arm/plat-mxc/devices.c
> @@ -89,3 +89,14 @@ err:
>
> return pdev;
> }
> +
> +struct device mxc_aips_bus = {
> + .init_name = "mxc_aips",
> + .parent = &platform_bus,
> +};
> +
> +static int __init mxc_device_init(void)
> +{
> + return device_register(&mxc_aips_bus);
> +}
> +core_initcall(mxc_device_init);
> diff --git a/arch/arm/plat-mxc/devices/Makefile b/arch/arm/plat-mxc/devices/Makefile
> index ad2922a..b41bf97 100644
> --- a/arch/arm/plat-mxc/devices/Makefile
> +++ b/arch/arm/plat-mxc/devices/Makefile
> @@ -2,6 +2,7 @@ obj-$(CONFIG_IMX_HAVE_PLATFORM_FEC) += platform-fec.o
> obj-$(CONFIG_IMX_HAVE_PLATFORM_FLEXCAN) += platform-flexcan.o
> obj-$(CONFIG_IMX_HAVE_PLATFORM_FSL_USB2_UDC) += platform-fsl-usb2-udc.o
> obj-$(CONFIG_IMX_HAVE_PLATFORM_GPIO_KEYS) += platform-gpio_keys.o
> +obj-y += platform-gpio-mxc.o
> obj-$(CONFIG_IMX_HAVE_PLATFORM_IMX21_HCD) += platform-imx21-hcd.o
> obj-$(CONFIG_IMX_HAVE_PLATFORM_IMX2_WDT) += platform-imx2-wdt.o
> obj-$(CONFIG_IMX_HAVE_PLATFORM_IMXDI_RTC) += platform-imxdi_rtc.o
> diff --git a/arch/arm/plat-mxc/devices/platform-gpio-mxc.c b/arch/arm/plat-mxc/devices/platform-gpio-mxc.c
> new file mode 100644
> index 0000000..cf1b7fd
> --- /dev/null
> +++ b/arch/arm/plat-mxc/devices/platform-gpio-mxc.c
> @@ -0,0 +1,32 @@
> +/*
> + * Copyright 2011 Freescale Semiconductor, Inc. All Rights Reserved.
> + * Copyright 2011 Linaro Limited
> + *
> + * This program is free software; you can redistribute it and/or modify it under
> + * the terms of the GNU General Public License version 2 as published by the
> + * Free Software Foundation.
> + */
> +#include <mach/devices-common.h>
> +
> +struct platform_device *__init mxc_register_gpio(int id,
> + resource_size_t iobase, resource_size_t iosize, int irq, int irq_high)
> +{
> + struct resource res[] = {
> + {
> + .start = iobase,
> + .end = iobase + iosize - 1,
> + .flags = IORESOURCE_MEM,
> + }, {
> + .start = irq,
> + .end = irq,
> + .flags = IORESOURCE_IRQ,
> + }, {
> + .start = irq_high,
> + .end = irq_high,
> + .flags = IORESOURCE_IRQ,
> + },
> + };
> +
> + return platform_device_register_resndata(&mxc_aips_bus,
> + "gpio-mxc", id, res, ARRAY_SIZE(res), NULL, 0);
> +}
> diff --git a/arch/arm/plat-mxc/include/mach/common.h b/arch/arm/plat-mxc/include/mach/common.h
> index da79918..91fa263 100644
> --- a/arch/arm/plat-mxc/include/mach/common.h
> +++ b/arch/arm/plat-mxc/include/mach/common.h
> @@ -43,6 +43,15 @@ extern void mx35_init_irq(void);
> extern void mx50_init_irq(void);
> extern void mx51_init_irq(void);
> extern void mx53_init_irq(void);
> +extern void imx1_soc_init(void);
> +extern void imx21_soc_init(void);
> +extern void imx25_soc_init(void);
> +extern void imx27_soc_init(void);
> +extern void imx31_soc_init(void);
> +extern void imx35_soc_init(void);
> +extern void imx50_soc_init(void);
> +extern void imx51_soc_init(void);
> +extern void imx53_soc_init(void);
> extern void epit_timer_init(struct clk *timer_clk, void __iomem *base, int irq);
> extern void mxc_timer_init(struct clk *timer_clk, void __iomem *, int);
> extern int mx1_clocks_init(unsigned long fref);
> @@ -55,7 +64,8 @@ extern int mx51_clocks_init(unsigned long ckil, unsigned long osc,
> unsigned long ckih1, unsigned long ckih2);
> extern int mx53_clocks_init(unsigned long ckil, unsigned long osc,
> unsigned long ckih1, unsigned long ckih2);
> -extern int mxc_register_gpios(void);
> +extern struct platform_device *mxc_register_gpio(int id,
> + resource_size_t iobase, resource_size_t iosize, int irq, int irq_high);
> extern int mxc_register_device(struct platform_device *pdev, void *data);
> extern void mxc_set_cpu_type(unsigned int type);
> extern void mxc_arch_reset_init(void __iomem *);
> diff --git a/arch/arm/plat-mxc/include/mach/devices-common.h b/arch/arm/plat-mxc/include/mach/devices-common.h
> index fa84773..03f6266 100644
> --- a/arch/arm/plat-mxc/include/mach/devices-common.h
> +++ b/arch/arm/plat-mxc/include/mach/devices-common.h
> @@ -10,6 +10,8 @@
> #include <linux/platform_device.h>
> #include <linux/init.h>
>
> +extern struct device mxc_aips_bus;
> +
> struct platform_device *imx_add_platform_device_dmamask(
> const char *name, int id,
> const struct resource *res, unsigned int num_resources,
> diff --git a/arch/arm/plat-mxc/include/mach/gpio.h b/arch/arm/plat-mxc/include/mach/gpio.h
> index a2747f1..31c820c 100644
> --- a/arch/arm/plat-mxc/include/mach/gpio.h
> +++ b/arch/arm/plat-mxc/include/mach/gpio.h
> @@ -36,31 +36,4 @@
> #define gpio_to_irq(gpio) (MXC_GPIO_IRQ_START + (gpio))
> #define irq_to_gpio(irq) ((irq) - MXC_GPIO_IRQ_START)
>
> -struct mxc_gpio_port {
> - void __iomem *base;
> - int irq;
> - int irq_high;
> - int virtual_irq_start;
> - struct gpio_chip chip;
> - u32 both_edges;
> - spinlock_t lock;
> -};
> -
> -#define DEFINE_IMX_GPIO_PORT_IRQ_HIGH(soc, _id, _hwid, _irq, _irq_high) \
> - { \
> - .chip.label = "gpio-" #_id, \
> - .irq = _irq, \
> - .irq_high = _irq_high, \
> - .base = soc ## _IO_ADDRESS( \
> - soc ## _GPIO ## _hwid ## _BASE_ADDR), \
> - .virtual_irq_start = MXC_GPIO_IRQ_START + (_id) * 32, \
> - }
> -
> -#define DEFINE_IMX_GPIO_PORT_IRQ(soc, _id, _hwid, _irq) \
> - DEFINE_IMX_GPIO_PORT_IRQ_HIGH(soc, _id, _hwid, _irq, 0)
> -#define DEFINE_IMX_GPIO_PORT(soc, _id, _hwid) \
> - DEFINE_IMX_GPIO_PORT_IRQ(soc, _id, _hwid, 0)
> -
> -int mxc_gpio_init(struct mxc_gpio_port*, int);
> -
> #endif
> diff --git a/drivers/gpio/gpio-mxc.c b/drivers/gpio/gpio-mxc.c
> index 6cd6d7f..844079a 100644
> --- a/drivers/gpio/gpio-mxc.c
> +++ b/drivers/gpio/gpio-mxc.c
> @@ -24,11 +24,28 @@
> #include <linux/io.h>
> #include <linux/irq.h>
> #include <linux/gpio.h>
> +#include <linux/platform_device.h>
> +#include <linux/slab.h>
> #include <mach/hardware.h>
> #include <asm-generic/bug.h>
>
> -static struct mxc_gpio_port *mxc_gpio_ports;
> -static int gpio_table_size;
> +struct mxc_gpio_port {
> + struct list_head node;
> + void __iomem *base;
> + int irq;
> + int irq_high;
> + int virtual_irq_start;
> + struct gpio_chip chip;
> + u32 both_edges;
> + spinlock_t lock;
> +};
> +
> +/*
> + * MX2 has one interrupt *for all* gpio ports. The list is used
> + * to save the references to all ports, so that mx2_gpio_irq_handler
> + * can walk through all interrupt status registers.
> + */
> +static LIST_HEAD(mxc_gpio_ports);
>
> #define cpu_is_mx1_mx2() (cpu_is_mx1() || cpu_is_mx2())
>
> @@ -50,7 +67,7 @@ static int gpio_table_size;
>
> static void _clear_gpio_irqstatus(struct mxc_gpio_port *port, u32 index)
> {
> - __raw_writel(1 << index, port->base + GPIO_ISR);
> + writel(1 << index, port->base + GPIO_ISR);
> }
>
> static void _set_gpio_irqenable(struct mxc_gpio_port *port, u32 index,
> @@ -58,27 +75,30 @@ static void _set_gpio_irqenable(struct mxc_gpio_port *port, u32 index,
> {
> u32 l;
>
> - l = __raw_readl(port->base + GPIO_IMR);
> + l = readl(port->base + GPIO_IMR);
> l = (l & (~(1 << index))) | (!!enable << index);
> - __raw_writel(l, port->base + GPIO_IMR);
> + writel(l, port->base + GPIO_IMR);
> }
>
> static void gpio_ack_irq(struct irq_data *d)
> {
> + struct mxc_gpio_port *port = irq_data_get_irq_chip_data(d);
> u32 gpio = irq_to_gpio(d->irq);
> - _clear_gpio_irqstatus(&mxc_gpio_ports[gpio / 32], gpio & 0x1f);
> + _clear_gpio_irqstatus(port, gpio & 0x1f);
> }
>
> static void gpio_mask_irq(struct irq_data *d)
> {
> + struct mxc_gpio_port *port = irq_data_get_irq_chip_data(d);
> u32 gpio = irq_to_gpio(d->irq);
> - _set_gpio_irqenable(&mxc_gpio_ports[gpio / 32], gpio & 0x1f, 0);
> + _set_gpio_irqenable(port, gpio & 0x1f, 0);
> }
>
> static void gpio_unmask_irq(struct irq_data *d)
> {
> + struct mxc_gpio_port *port = irq_data_get_irq_chip_data(d);
> u32 gpio = irq_to_gpio(d->irq);
> - _set_gpio_irqenable(&mxc_gpio_ports[gpio / 32], gpio & 0x1f, 1);
> + _set_gpio_irqenable(port, gpio & 0x1f, 1);
> }
>
> static int mxc_gpio_get(struct gpio_chip *chip, unsigned offset);
> @@ -86,7 +106,7 @@ static int mxc_gpio_get(struct gpio_chip *chip, unsigned offset);
> static int gpio_set_irq_type(struct irq_data *d, u32 type)
> {
> u32 gpio = irq_to_gpio(d->irq);
> - struct mxc_gpio_port *port = &mxc_gpio_ports[gpio / 32];
> + struct mxc_gpio_port *port = irq_data_get_irq_chip_data(d);
> u32 bit, val;
> int edge;
> void __iomem *reg = port->base;
> @@ -122,8 +142,8 @@ static int gpio_set_irq_type(struct irq_data *d, u32 type)
>
> reg += GPIO_ICR1 + ((gpio & 0x10) >> 2); /* lower or upper register */
> bit = gpio & 0xf;
> - val = __raw_readl(reg) & ~(0x3 << (bit << 1));
> - __raw_writel(val | (edge << (bit << 1)), reg);
> + val = readl(reg) & ~(0x3 << (bit << 1));
> + writel(val | (edge << (bit << 1)), reg);
> _clear_gpio_irqstatus(port, gpio & 0x1f);
>
> return 0;
> @@ -137,7 +157,7 @@ static void mxc_flip_edge(struct mxc_gpio_port *port, u32 gpio)
>
> reg += GPIO_ICR1 + ((gpio & 0x10) >> 2); /* lower or upper register */
> bit = gpio & 0xf;
> - val = __raw_readl(reg);
> + val = readl(reg);
> edge = (val >> (bit << 1)) & 3;
> val &= ~(0x3 << (bit << 1));
> if (edge == GPIO_INT_HIGH_LEV) {
> @@ -151,7 +171,7 @@ static void mxc_flip_edge(struct mxc_gpio_port *port, u32 gpio)
> gpio, edge);
> return;
> }
> - __raw_writel(val | (edge << (bit << 1)), reg);
> + writel(val | (edge << (bit << 1)), reg);
> }
>
> /* handle 32 interrupts in one status register */
> @@ -177,8 +197,7 @@ static void mx3_gpio_irq_handler(u32 irq, struct irq_desc *desc)
> u32 irq_stat;
> struct mxc_gpio_port *port = irq_get_handler_data(irq);
>
> - irq_stat = __raw_readl(port->base + GPIO_ISR) &
> - __raw_readl(port->base + GPIO_IMR);
> + irq_stat = readl(port->base + GPIO_ISR) & readl(port->base + GPIO_IMR);
>
> mxc_gpio_irq_handler(port, irq_stat);
> }
> @@ -186,19 +205,18 @@ static void mx3_gpio_irq_handler(u32 irq, struct irq_desc *desc)
> /* MX2 has one interrupt *for all* gpio ports */
> static void mx2_gpio_irq_handler(u32 irq, struct irq_desc *desc)
> {
> - int i;
> u32 irq_msk, irq_stat;
> - struct mxc_gpio_port *port = irq_get_handler_data(irq);
> + struct mxc_gpio_port *port;
>
> /* walk through all interrupt status registers */
> - for (i = 0; i < gpio_table_size; i++) {
> - irq_msk = __raw_readl(port[i].base + GPIO_IMR);
> + list_for_each_entry(port, &mxc_gpio_ports, node) {
> + irq_msk = readl(port->base + GPIO_IMR);
> if (!irq_msk)
> continue;
>
> - irq_stat = __raw_readl(port[i].base + GPIO_ISR) & irq_msk;
> + irq_stat = readl(port->base + GPIO_ISR) & irq_msk;
> if (irq_stat)
> - mxc_gpio_irq_handler(&port[i], irq_stat);
> + mxc_gpio_irq_handler(port, irq_stat);
> }
> }
>
> @@ -215,7 +233,7 @@ static int gpio_set_wake_irq(struct irq_data *d, u32 enable)
> {
> u32 gpio = irq_to_gpio(d->irq);
> u32 gpio_idx = gpio & 0x1F;
> - struct mxc_gpio_port *port = &mxc_gpio_ports[gpio / 32];
> + struct mxc_gpio_port *port = irq_data_get_irq_chip_data(d);
>
> if (enable) {
> if (port->irq_high && (gpio_idx >= 16))
> @@ -250,12 +268,12 @@ static void _set_gpio_direction(struct gpio_chip *chip, unsigned offset,
> unsigned long flags;
>
> spin_lock_irqsave(&port->lock, flags);
> - l = __raw_readl(port->base + GPIO_GDIR);
> + l = readl(port->base + GPIO_GDIR);
> if (dir)
> l |= 1 << offset;
> else
> l &= ~(1 << offset);
> - __raw_writel(l, port->base + GPIO_GDIR);
> + writel(l, port->base + GPIO_GDIR);
> spin_unlock_irqrestore(&port->lock, flags);
> }
>
> @@ -268,8 +286,8 @@ static void mxc_gpio_set(struct gpio_chip *chip, unsigned offset, int value)
> unsigned long flags;
>
> spin_lock_irqsave(&port->lock, flags);
> - l = (__raw_readl(reg) & (~(1 << offset))) | (!!value << offset);
> - __raw_writel(l, reg);
> + l = (readl(reg) & (~(1 << offset))) | (!!value << offset);
> + writel(l, reg);
> spin_unlock_irqrestore(&port->lock, flags);
> }
>
> @@ -278,7 +296,7 @@ static int mxc_gpio_get(struct gpio_chip *chip, unsigned offset)
> struct mxc_gpio_port *port =
> container_of(chip, struct mxc_gpio_port, chip);
>
> - return (__raw_readl(port->base + GPIO_PSR) >> offset) & 1;
> + return (readl(port->base + GPIO_PSR) >> offset) & 1;
> }
>
> static int mxc_gpio_direction_input(struct gpio_chip *chip, unsigned offset)
> @@ -301,61 +319,116 @@ static int mxc_gpio_direction_output(struct gpio_chip *chip,
> */
> static struct lock_class_key gpio_lock_class;
>
> -int __init mxc_gpio_init(struct mxc_gpio_port *port, int cnt)
> +static int __devinit mxc_gpio_probe(struct platform_device *pdev)
> {
> - int i, j;
> -
> - /* save for local usage */
> - mxc_gpio_ports = port;
> - gpio_table_size = cnt;
> -
> - printk(KERN_INFO "MXC GPIO hardware\n");
> -
> - for (i = 0; i < cnt; i++) {
> - /* disable the interrupt and clear the status */
> - __raw_writel(0, port[i].base + GPIO_IMR);
> - __raw_writel(~0, port[i].base + GPIO_ISR);
> - for (j = port[i].virtual_irq_start;
> - j < port[i].virtual_irq_start + 32; j++) {
> - irq_set_lockdep_class(j, &gpio_lock_class);
> - irq_set_chip_and_handler(j, &gpio_irq_chip,
> - handle_level_irq);
> - set_irq_flags(j, IRQF_VALID);
> - }
> + struct mxc_gpio_port *port;
> + struct resource *iores;
> + int err, i;
> +
> + port = kzalloc(sizeof(struct mxc_gpio_port), GFP_KERNEL);
> + if (!port)
> + return -ENOMEM;
>
> - /* register gpio chip */
> - port[i].chip.direction_input = mxc_gpio_direction_input;
> - port[i].chip.direction_output = mxc_gpio_direction_output;
> - port[i].chip.get = mxc_gpio_get;
> - port[i].chip.set = mxc_gpio_set;
> - port[i].chip.base = i * 32;
> - port[i].chip.ngpio = 32;
> + port->virtual_irq_start = MXC_GPIO_IRQ_START + pdev->id * 32;
>
> - spin_lock_init(&port[i].lock);
> + iores = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> + if (!iores) {
> + err = -ENODEV;
> + goto out_kfree;
> + }
>
> - /* its a serious configuration bug when it fails */
> - BUG_ON( gpiochip_add(&port[i].chip) < 0 );
> + if (!request_mem_region(iores->start, resource_size(iores),
> + pdev->name)) {
> + err = -EBUSY;
> + goto out_kfree;
> + }
>
> - if (cpu_is_mx1() || cpu_is_mx3() || cpu_is_mx25() || cpu_is_mx51()) {
> - /* setup one handler for each entry */
> - irq_set_chained_handler(port[i].irq,
> - mx3_gpio_irq_handler);
> - irq_set_handler_data(port[i].irq, &port[i]);
> - if (port[i].irq_high) {
> - /* setup handler for GPIO 16 to 31 */
> - irq_set_chained_handler(port[i].irq_high,
> - mx3_gpio_irq_handler);
> - irq_set_handler_data(port[i].irq_high,
> - &port[i]);
> - }
> - }
> + port->base = ioremap(iores->start, resource_size(iores));
> + if (!port->base) {
> + err = -ENOMEM;
> + goto out_release_mem;
> + }
> +
> + port->irq_high = platform_get_irq(pdev, 1);
> + port->irq = platform_get_irq(pdev, 0);
> + if (port->irq < 0) {
> + err = -EINVAL;
> + goto out_iounmap;
> + }
> +
> + /* disable the interrupt and clear the status */
> + writel(0, port->base + GPIO_IMR);
> + writel(~0, port->base + GPIO_ISR);
> +
> + for (i = port->virtual_irq_start;
> + i < port->virtual_irq_start + 32; i++) {
> + irq_set_lockdep_class(i, &gpio_lock_class);
> + irq_set_chip_and_handler(i, &gpio_irq_chip, handle_level_irq);
> + set_irq_flags(i, IRQF_VALID);
> + irq_set_chip_data(i, port);
> }
>
> if (cpu_is_mx2()) {
> /* setup one handler for all GPIO interrupts */
> - irq_set_chained_handler(port[0].irq, mx2_gpio_irq_handler);
> - irq_set_handler_data(port[0].irq, port);
> + if (pdev->id == 0)
> + irq_set_chained_handler(port->irq,
> + mx2_gpio_irq_handler);
> + } else {
> + /* setup one handler for each entry */
> + irq_set_chained_handler(port->irq, mx3_gpio_irq_handler);
> + irq_set_handler_data(port->irq, port);
> + if (port->irq_high > 0) {
> + /* setup handler for GPIO 16 to 31 */
> + irq_set_chained_handler(port->irq_high,
> + mx3_gpio_irq_handler);
> + irq_set_handler_data(port->irq_high, port);
> + }
> }
>
> + /* register gpio chip */
> + port->chip.direction_input = mxc_gpio_direction_input;
> + port->chip.direction_output = mxc_gpio_direction_output;
> + port->chip.get = mxc_gpio_get;
> + port->chip.set = mxc_gpio_set;
> + port->chip.base = pdev->id * 32;
> + port->chip.ngpio = 32;
> +
> + spin_lock_init(&port->lock);
> +
> + err = gpiochip_add(&port->chip);
> + if (err)
> + goto out_iounmap;
> +
> + list_add_tail(&port->node, &mxc_gpio_ports);
> +
> return 0;
> +
> +out_iounmap:
> + iounmap(port->base);
> +out_release_mem:
> + release_mem_region(iores->start, resource_size(iores));
> +out_kfree:
> + kfree(port);
> + dev_info(&pdev->dev, "%s failed with errno %d\n", __func__, err);
> + return err;
> }
> +
> +static struct platform_driver mxc_gpio_driver = {
> + .driver = {
> + .name = "gpio-mxc",
> + .owner = THIS_MODULE,
> + },
> + .probe = mxc_gpio_probe,
> +};
> +
> +static int __init gpio_mxc_init(void)
> +{
> + return platform_driver_register(&mxc_gpio_driver);
> +}
> +postcore_initcall(gpio_mxc_init);
> +
> +MODULE_AUTHOR("Freescale Semiconductor, "
> + "Daniel Mack <danielncaiaq.de>, "
> + "Juergen Beisert <kernel at pengutronix.de>");
> +MODULE_DESCRIPTION("Freescale MXC GPIO");
> +MODULE_LICENSE("GPL");
> --
> 1.7.4.1
>
More information about the linux-arm-kernel
mailing list