[PATCH v3 2/4] mmc: support sdhci-pxav2.c
Philip Rakity
prakity at marvell.com
Fri Jun 3 20:04:42 EDT 2011
>
>
> On Jun 3, 2011, at 11:42 AM, Philip Rakity wrote:
>
>>
>> On Jun 3, 2011, at 2:50 AM, Zhangfei Gao wrote:
>>
>>> SDHCI driver for pxav2 SoCs, such as pxa910, the driver based on sdhci-pltfm to handle resource etc.
>>>
>>> Signed-off-by: Zhangfei Gao <zhangfei.gao at marvell.com>
>>> Signed-off-by: Jun Nie <njun at marvell.com>
>>> Signed-off-by: Qiming Wu <wuqm at marvell.com>
>>> ---
>>> drivers/mmc/host/Kconfig | 11 ++
>>> drivers/mmc/host/Makefile | 1 +
>>> drivers/mmc/host/sdhci-pxav2.c | 261 ++++++++++++++++++++++++++++++++++++++++
>>> 3 files changed, 273 insertions(+), 0 deletions(-)
>>> create mode 100644 drivers/mmc/host/sdhci-pxav2.c
>>>
>>> diff --git a/drivers/mmc/host/Kconfig b/drivers/mmc/host/Kconfig
>>> index 4ee869a..1a53d59 100644
>>> --- a/drivers/mmc/host/Kconfig
>>> +++ b/drivers/mmc/host/Kconfig
>>> @@ -192,6 +192,17 @@ config MMC_SDHCI_PXAV3
>>>
>>> If unsure, say N.
>>>
>>> +config MMC_SDHCI_PXAV2
>>> + tristate "Marvell PXAV2 SD Host Controller support"
>>> + select MMC_SDHCI
>>> + select MMC_SDHCI_PLTFM
>>> + help
>>> + This selects the Marvell(R) PXAV2 SD Host Controller.
>>> + If you have a PXAV2 platform (such as pxa910) with SD Host Controller
>>> + and a card slot, say Y or M here.
>>> +
>>> + If unsure, say N.
>>> +
>>> config MMC_SDHCI_SPEAR
>>> tristate "SDHCI support on ST SPEAr platform"
>>> depends on MMC_SDHCI && PLAT_SPEAR
>>> diff --git a/drivers/mmc/host/Makefile b/drivers/mmc/host/Makefile
>>> index 9131a27..cf95330 100644
>>> --- a/drivers/mmc/host/Makefile
>>> +++ b/drivers/mmc/host/Makefile
>>> @@ -10,6 +10,7 @@ obj-$(CONFIG_MMC_MXS) += mxs-mmc.o
>>> obj-$(CONFIG_MMC_SDHCI) += sdhci.o
>>> obj-$(CONFIG_MMC_SDHCI_PCI) += sdhci-pci.o
>>> obj-$(CONFIG_MMC_SDHCI_PXAV3) += sdhci-pxav3.o
>>> +obj-$(CONFIG_MMC_SDHCI_PXAV2) += sdhci-pxav2.o
>>> obj-$(CONFIG_MMC_SDHCI_S3C) += sdhci-s3c.o
>>> obj-$(CONFIG_MMC_SDHCI_SPEAR) += sdhci-spear.o
>>> obj-$(CONFIG_MMC_WBSD) += wbsd.o
>>> diff --git a/drivers/mmc/host/sdhci-pxav2.c b/drivers/mmc/host/sdhci-pxav2.c
>>> new file mode 100644
>>> index 0000000..759f526
>>> --- /dev/null
>>> +++ b/drivers/mmc/host/sdhci-pxav2.c
>>> @@ -0,0 +1,261 @@
>>> +/*
>>> + * Copyright (C) 2010 Marvell International Ltd.
>>> + * Zhangfei Gao <zhangfei.gao at marvell.com>
>>> + * Kevin Wang <dwang4 at marvell.com>
>>> + * Jun Nie <njun at marvell.com>
>>> + * Qiming Wu <wuqm at marvell.com>
>>> + * Philip Rakity <prakity at marvell.com>
>>> + *
>>> + * This software is licensed under the terms of the GNU General Public
>>> + * License version 2, as published by the Free Software Foundation, and
>>> + * may be copied, distributed, and modified under those terms.
>>> + *
>>> + * This program is distributed in the hope that it will be useful,
>>> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
>>> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
>>> + * GNU General Public License for more details.
>>> + *
>>> + */
>>> +
>>> +#include <linux/err.h>
>>> +#include <linux/init.h>
>>> +#include <linux/platform_device.h>
>>> +#include <linux/clk.h>
>>> +#include <linux/io.h>
>>> +#include <linux/gpio.h>
>>> +#include <linux/mmc/card.h>
>>> +#include <linux/mmc/host.h>
>>> +#include <plat/sdhci.h>
>>> +#include <linux/slab.h>
>>> +#include "sdhci.h"
>>> +#include "sdhci-pltfm.h"
>>> +
>>> +#define SD_FIFO_PARAM 0xe0
>>> +#define DIS_PAD_SD_CLK_GATE 0x0400 /* Turn on/off Dynamic SD Clock Gating */
>>> +#define CLK_GATE_ON 0x0200 /* Disable/enable Clock Gate */
>>> +#define CLK_GATE_CTL 0x0100 /* Clock Gate Control */
>>> +#define CLK_GATE_SETTING_BITS (DIS_PAD_SD_CLK_GATE | \
>>> + CLK_GATE_ON | CLK_GATE_CTL)
>>> +
>>> +#define SD_CLOCK_BURST_SIZE_SETUP 0xe6
>>> +#define SDCLK_SEL_SHIFT 8
>>> +#define SDCLK_SEL_MASK 0x3
>>> +#define SDCLK_DELAY_SHIFT 10
>>> +#define SDCLK_DELAY_MASK 0x3c
>>> +
>>> +#define SDHCI_HOST_CONTROL 0x28
>
This definition should come from the sdhci.h include file since it is part of the sd host controller spec.
> .
>
>>> +#define SDHCI_CTRL_4BITBUS 0x02
>>> +
>>> +#define SD_CE_ATA_2 0xea
>>> +#define MMC_CARD 0x1000
>>> +#define MMC_WIDTH 0x0100
>>> +
>>> +static void pxav2_set_private_registers(struct sdhci_host *host, u8 mask)
>>> +{
>>> + struct platform_device *pdev = to_platform_device(mmc_dev(host->mmc));
>>> + struct sdhci_pxa_platdata *pdata = pdev->dev.platform_data;
>>> +
>>> + if (mask == SDHCI_RESET_ALL) {
>>> + u16 tmp = 0;
>>> +
>>> + /*
>>> + * tune timing of read data/command when crc error happen
>>> + * no performance impact
>>> + */
>>> + if (pdata->clk_delay_sel == 1) {
>>> + tmp = readw(host->ioaddr + SD_CLOCK_BURST_SIZE_SETUP);
>>> +
>>> + tmp &= ~(SDCLK_DELAY_MASK << SDCLK_DELAY_SHIFT);
>>> + tmp |= (pdata->clk_delay_cycles & SDCLK_DELAY_MASK)
>>> + << SDCLK_DELAY_SHIFT;
>>> + tmp &= ~(SDCLK_SEL_MASK << SDCLK_SEL_SHIFT);
>>> + tmp |= (1 & SDCLK_SEL_MASK) << SDCLK_SEL_SHIFT;
>>> +
>>> + writew(tmp, host->ioaddr + SD_CLOCK_BURST_SIZE_SETUP);
>>> + }
>>> +
>>> + if (pdata->flags & PXA_FLAG_ENABLE_CLOCK_GATING) {
>>> + tmp = readw(host->ioaddr + SD_FIFO_PARAM);
>>> + tmp &= ~CLK_GATE_SETTING_BITS;
>>> + writew(tmp, host->ioaddr + SD_FIFO_PARAM);
>>> + } else {
>>> + tmp = readw(host->ioaddr + SD_FIFO_PARAM);
>>> + tmp &= ~CLK_GATE_SETTING_BITS;
>>> + tmp |= CLK_GATE_SETTING_BITS;
>>> + writew(tmp, host->ioaddr + SD_FIFO_PARAM);
>>> + }
>>> + }
>>> +}
>>> +
>>> +static int pxav2_mmc_set_width(struct sdhci_host *host, int width)
>>> +{
>>> + u8 ctrl;
>>> + u16 tmp;
>>> +
>>> + ctrl = readb(host->ioaddr + SDHCI_HOST_CONTROL);
>>> + tmp = readw(host->ioaddr + SD_CE_ATA_2);
>>> + if (width == MMC_BUS_WIDTH_8) {
>>> + ctrl &= ~SDHCI_CTRL_4BITBUS;
>>> + tmp |= MMC_CARD | MMC_WIDTH;
>>> + } else {
>>> + tmp &= ~(MMC_CARD | MMC_WIDTH);
>>> + if (width == MMC_BUS_WIDTH_4)
>>> + ctrl |= SDHCI_CTRL_4BITBUS;
>>> + else
>>> + ctrl &= ~SDHCI_CTRL_4BITBUS;
>>> + }
>>> + writew(tmp, host->ioaddr + SD_CE_ATA_2);
>>> + writeb(ctrl, host->ioaddr + SDHCI_HOST_CONTROL);
>>> +
>>> + return 0;
>>> +}
>>> +
>>> +static unsigned int pxav2_get_ro(struct sdhci_host *host)
>>> +{
>>> + /* Micro SD does not support write-protect feature */
>>> + return 0;
>>> +}
>>> +
>>> +static u32 pxav2_get_max_clock(struct sdhci_host *host)
>>> +{
>>> + struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
>>> +
>>> + return clk_get_rate(pltfm_host->clk);
>>> +}
>>> +
>>> +static struct sdhci_ops pxav2_sdhci_ops = {
>>> + .get_ro = pxav2_get_ro,
>>> + .get_max_clock = pxav2_get_max_clock,
>>> + .platform_reset_exit = pxav2_set_private_registers,
>>> + .platform_8bit_width = pxav2_mmc_set_width,
>>> +};
>>> +
>>> +static int __devinit sdhci_pxav2_probe(struct platform_device *pdev)
>>> +{
>>> + struct sdhci_pltfm_host *pltfm_host;
>>> + struct sdhci_pxa_platdata *pdata = pdev->dev.platform_data;
>>> + struct device *dev = &pdev->dev;
>>> + struct sdhci_host *host = NULL;
>>> + struct sdhci_pxa *pxa = NULL;
>>> + int ret;
>>> + struct clk *clk;
>>> +
>>> + pxa = kzalloc(sizeof(struct sdhci_pxa), GFP_KERNEL);
>>> + if (!pxa)
>>> + return -ENOMEM;
>>> +
>>> + host = sdhci_pltfm_init(pdev, NULL);
>>> + if (IS_ERR(host)) {
>>> + kfree(pxa);
>>> + return PTR_ERR(host);
>>> + }
>>> + pltfm_host = sdhci_priv(host);
>>> + pltfm_host->priv = pxa;
>>> +
>>> + clk = clk_get(dev, "PXA-SDHCLK");
>>> + if (IS_ERR(clk)) {
>>> + dev_err(dev, "failed to get io clock\n");
>>> + ret = PTR_ERR(clk);
>>> + goto err_clk_get;
>>> + }
>>> + pltfm_host->clk = clk;
>>> + clk_enable(clk);
>>> +
>>> + host->quirks = SDHCI_QUIRK_BROKEN_ADMA
>>> + | SDHCI_QUIRK_BROKEN_TIMEOUT_VAL
>>> + | SDHCI_QUIRK_CAP_CLOCK_BASE_BROKEN;
>>> +
>>> + if (pdata) {
>>> + if (pdata->flags & PXA_FLAG_CARD_PERMANENT) {
>>> + /* on-chip device */
>>> + host->quirks |= SDHCI_QUIRK_BROKEN_CARD_DETECTION;
>>> + host->mmc->caps |= MMC_CAP_NONREMOVABLE;
>>> + }
>>> +
>>> + /* If slot design supports 8 bit data, indicate this to MMC. */
>>> + if (pdata->flags & PXA_FLAG_SD_8_BIT_CAPABLE_SLOT)
>>> + host->mmc->caps |= MMC_CAP_8_BIT_DATA;
>>> +
>>> + if (pdata->quirks)
>>> + host->quirks |= pdata->quirks;
>>> + if (pdata->host_caps)
>>> + host->mmc->caps |= pdata->host_caps;
>>> + if (pdata->pm_caps)
>>> + host->mmc->pm_caps |= pdata->pm_caps;
>>> + }
>>> +
>>> + host->ops = &pxav2_sdhci_ops;
>>> +
>>> + ret = sdhci_add_host(host);
>>> + if (ret) {
>>> + dev_err(&pdev->dev, "failed to add host\n");
>>> + goto err_add_host;
>>> + }
>>> +
>>> + if (pdata && pdata->max_speed) {
>>> + host->mmc->f_max = pdata->max_speed;
>>> + if (!(host->mmc->f_max > 25000000))
>>> + host->mmc->caps &= ~(MMC_CAP_SD_HIGHSPEED |
>>> + MMC_CAP_MMC_HIGHSPEED);
>>> + }
>>
>> This should be done before calling add_host. Add the callback to set f_max()
>>
>> https://patchwork.kernel.org/patch/742301/
>>
>>
>>
>>
>>> +
>>> + platform_set_drvdata(pdev, host);
>>> +
>>>
>>> + return 0;
>>> +
>>> +err_add_host:
>>> + clk_disable(clk);
>>> + clk_put(clk);
>>> +err_clk_get:
>>> + sdhci_pltfm_free(pdev);+ kfree(pxa);
>>> + return ret;
>>> +}
>>> +
>>> +static int __devexit sdhci_pxav2_remove(struct platform_device *pdev)
>>> +{
>>> + struct sdhci_host *host = platform_get_drvdata(pdev);
>>> + struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
>>> + struct sdhci_pxa *pxa = pltfm_host->priv;
>>> +
>>> + sdhci_remove_host(host, 1);
>>> +
>>> + clk_disable(pltfm_host->clk);
>>> + clk_put(pltfm_host->clk);
>>> + sdhci_pltfm_free(pdev);
>>> + kfree(pxa);
>>> +
>>> + platform_set_drvdata(pdev, NULL);
>>> +
>>> + return 0;
>>> +}
>>> +
>>> +static struct platform_driver sdhci_pxav2_driver = {
>>> + .driver = {
>>> + .name = "sdhci-pxav2",
>>> + .owner = THIS_MODULE,
>>> + },
>>> + .probe = sdhci_pxav2_probe,
>>> + .remove = __devexit_p(sdhci_pxav2_remove),
>>> +#ifdef CONFIG_PM
>>> + .suspend = sdhci_pltfm_suspend,
>>> + .resume = sdhci_pltfm_resume,
>>> +#endif
>>
>> could you please post to mmc mailing list code that sets up sdhci-pxav2.
>>
>>> +};
>>> +static int __init sdhci_pxav2_init(void)
>>> +{
>>> + return platform_driver_register(&sdhci_pxav2_driver);
>>> +}
>>> +
>>> +static void __exit sdhci_pxav2_exit(void)
>>> +{
>>> + platform_driver_unregister(&sdhci_pxav2_driver);
>>> +}
>>> +
>>> +module_init(sdhci_pxav2_init);
>>> +module_exit(sdhci_pxav2_exit);
>>> +
>>> +MODULE_DESCRIPTION("SDHCI driver for pxav2");
>>> +MODULE_AUTHOR("Marvell International Ltd.");
>>> +MODULE_LICENSE("GPL v2");
>>> +
>>> --
>>> 1.7.0.4
>>>
>>
>
More information about the linux-arm-kernel
mailing list