[PATCH v4 20/20] gpio/omap: cleanup prepare_for_idle and resume_after_idle
Tarun Kanti DebBarma
tarun.kanti at ti.com
Wed Jul 13 09:54:19 EDT 2011
Simplify omap2_gpio_prepare_for_idle() and omap2_gpio_resume_after_idle()
by moving most of the stuff to *_pm_runtime_suspend() and *_pm_runtime_resume().
Also, omap_gpio_suspend() and omap_gpio_resume() optimized to operate per
GPIO bank instead of operating on entire list every time.
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti at ti.com>
Signed-off-by: Charulatha V <charu at ti.com>
---
drivers/gpio/gpio-omap.c | 234 ++++++++++++++++++++++++---------------------
1 files changed, 125 insertions(+), 109 deletions(-)
diff --git a/drivers/gpio/gpio-omap.c b/drivers/gpio/gpio-omap.c
index 47e5e20..32281f6 100644
--- a/drivers/gpio/gpio-omap.c
+++ b/drivers/gpio/gpio-omap.c
@@ -1145,142 +1145,153 @@ static int omap_gpio_resume(struct device *dev)
static void omap_gpio_save_context(struct gpio_bank *bank);
static void omap_gpio_restore_context(struct gpio_bank *bank);
-void omap2_gpio_prepare_for_idle(int off_mode)
+static int omap_gpio_runtime_suspend(struct device *dev)
{
- struct gpio_bank *bank;
+ struct platform_device *pdev = to_platform_device(dev);
+ struct gpio_bank *bank = platform_get_drvdata(pdev);
+ u32 l1 = 0, l2 = 0;
+ int j;
- list_for_each_entry(bank, &omap_gpio_list, node) {
- u32 l1 = 0, l2 = 0;
- int j;
+ for (j = 0; j < hweight_long(bank->dbck_enable_mask); j++)
+ clk_disable(bank->dbck);
- if (!bank->loses_context)
- continue;
+ /* If going to OFF, remove triggering for all
+ * non-wakeup GPIOs. Otherwise spurious IRQs will be
+ * generated. See OMAP2420 Errata item 1.101. */
+ if (!(bank->enabled_non_wakeup_gpios))
+ goto save_gpio_ctx;
- for (j = 0; j < hweight_long(bank->dbck_enable_mask); j++)
- clk_disable(bank->dbck);
+ bank->saved_datain = __raw_readl(bank->base +
+ bank->regs->datain);
+ l1 = __raw_readl(bank->base + bank->regs->fallingdetect);
+ l2 = __raw_readl(bank->base + bank->regs->risingdetect);
- if (!off_mode)
- continue;
+ bank->saved_fallingdetect = l1;
+ bank->saved_risingdetect = l2;
+ l1 &= ~bank->enabled_non_wakeup_gpios;
+ l2 &= ~bank->enabled_non_wakeup_gpios;
- if (IS_ERR_VALUE(pm_runtime_put_sync(bank->dev) < 0))
- dev_err(bank->dev, "%s: GPIO bank %d "
- "pm_runtime_put_sync failed\n",
- __func__, bank->id);
+ __raw_writel(l1, bank->base + bank->regs->fallingdetect);
+ __raw_writel(l2, bank->base + bank->regs->risingdetect);
+
+save_gpio_ctx:
+ if (bank->get_context_loss_count)
+ bank->ctx_loss_count = bank->get_context_loss_count(bank->dev);
+ omap_gpio_save_context(bank);
+
+ return 0;
+}
+
+static int omap_gpio_runtime_resume(struct device *dev)
+{
+ struct platform_device *pdev = to_platform_device(dev);
+ struct gpio_bank *bank = platform_get_drvdata(pdev);
+ u32 ctx_lost_cnt_after;
+ u32 l = 0, gen, gen0, gen1;
+ int j;
+
+ for (j = 0; j < hweight_long(bank->dbck_enable_mask); j++)
+ clk_enable(bank->dbck);
- /* If going to OFF, remove triggering for all
- * non-wakeup GPIOs. Otherwise spurious IRQs will be
- * generated. See OMAP2420 Errata item 1.101. */
- if (!(bank->enabled_non_wakeup_gpios))
- goto save_gpio_ctx;
+ if (bank->get_context_loss_count) {
+ ctx_lost_cnt_after =
+ bank->get_context_loss_count(bank->dev);
+ if (ctx_lost_cnt_after != bank->ctx_loss_count ||
+ !ctx_lost_cnt_after)
+ omap_gpio_restore_context(bank);
+ }
- bank->saved_datain = __raw_readl(bank->base +
- bank->regs->datain);
- l1 = __raw_readl(bank->base + bank->regs->fallingdetect);
- l2 = __raw_readl(bank->base + bank->regs->risingdetect);
+ if (!(bank->enabled_non_wakeup_gpios))
+ return 0;
- bank->saved_fallingdetect = l1;
- bank->saved_risingdetect = l2;
- l1 &= ~bank->enabled_non_wakeup_gpios;
- l2 &= ~bank->enabled_non_wakeup_gpios;
+ __raw_writel(bank->saved_fallingdetect,
+ bank->base + bank->regs->fallingdetect);
+ __raw_writel(bank->saved_risingdetect,
+ bank->base + bank->regs->risingdetect);
+ l = __raw_readl(bank->base + bank->regs->datain);
- __raw_writel(l1, bank->base + bank->regs->fallingdetect);
- __raw_writel(l2, bank->base + bank->regs->risingdetect);
+ /* Check if any of the non-wakeup interrupt GPIOs have changed
+ * state. If so, generate an IRQ by software. This is
+ * horribly racy, but it's the best we can do to work around
+ * this silicon bug. */
+ l ^= bank->saved_datain;
+ l &= bank->enabled_non_wakeup_gpios;
-save_gpio_ctx:
- if (bank->get_context_loss_count)
- bank->ctx_loss_count =
- bank->get_context_loss_count(bank->dev);
+ /*
+ * No need to generate IRQs for the rising edge for gpio IRQs
+ * configured with falling edge only; and vice versa.
+ */
+ gen0 = l & bank->saved_fallingdetect;
+ gen0 &= bank->saved_datain;
+ gen1 = l & bank->saved_risingdetect;
+ gen1 &= ~(bank->saved_datain);
+
+ /* FIXME: Consider GPIO IRQs with level detections properly! */
+ gen = l & (~(bank->saved_fallingdetect) &
+ ~(bank->saved_risingdetect));
+ /* Consider all GPIO IRQs needed to be updated */
+ gen |= gen0 | gen1;
+
+ if (gen) {
+ u32 old0, old1;
+
+ old0 = __raw_readl(bank->base +
+ bank->regs->leveldetect0);
+ old1 = __raw_readl(bank->base +
+ bank->regs->leveldetect1);
+
+ __raw_writel(old0, bank->base +
+ bank->regs->leveldetect0);
+ __raw_writel(old1, bank->base +
+ bank->regs->leveldetect1);
+ if (cpu_is_omap24xx() || cpu_is_omap34xx()) {
+ old0 |= gen;
+ old1 |= gen;
+ }
- omap_gpio_save_context(bank);
+ if (cpu_is_omap44xx()) {
+ old0 |= l;
+ old1 |= l;
+ }
+ __raw_writel(old0, bank->base +
+ bank->regs->leveldetect0);
+ __raw_writel(old1, bank->base +
+ bank->regs->leveldetect1);
}
+
+ return 0;
}
-void omap2_gpio_resume_after_idle(void)
+void omap2_gpio_prepare_for_idle(int off_mode)
{
struct gpio_bank *bank;
- list_for_each_entry(bank, &omap_gpio_list, node) {
- u32 ctx_lost_cnt_after;
- u32 l = 0, gen, gen0, gen1;
- int j;
+ if (!off_mode)
+ return;
- if (!bank->loses_context)
+ list_for_each_entry(bank, &omap_gpio_list, node) {
+ if (!bank->mod_usage || !bank->loses_context)
continue;
- if (IS_ERR_VALUE(pm_runtime_get_sync(bank->dev) < 0))
+ if (IS_ERR_VALUE(pm_runtime_put_sync(bank->dev) < 0))
dev_err(bank->dev, "%s: GPIO bank %d "
- "pm_runtime_get_sync failed\n",
+ "pm_runtime_put_sync failed\n",
__func__, bank->id);
+ }
+}
- for (j = 0; j < hweight_long(bank->dbck_enable_mask); j++)
- clk_enable(bank->dbck);
-
- if (bank->get_context_loss_count) {
- ctx_lost_cnt_after =
- bank->get_context_loss_count(bank->dev);
- if (ctx_lost_cnt_after != bank->ctx_loss_count ||
- !ctx_lost_cnt_after)
- omap_gpio_restore_context(bank);
- }
+void omap2_gpio_resume_after_idle(void)
+{
+ struct gpio_bank *bank;
- if (!(bank->enabled_non_wakeup_gpios))
+ list_for_each_entry(bank, &omap_gpio_list, node) {
+ if (!bank->mod_usage || !bank->loses_context)
continue;
- __raw_writel(bank->saved_fallingdetect,
- bank->base + bank->regs->fallingdetect);
- __raw_writel(bank->saved_risingdetect,
- bank->base + bank->regs->risingdetect);
- l = __raw_readl(bank->base + bank->regs->datain);
-
- /* Check if any of the non-wakeup interrupt GPIOs have changed
- * state. If so, generate an IRQ by software. This is
- * horribly racy, but it's the best we can do to work around
- * this silicon bug. */
- l ^= bank->saved_datain;
- l &= bank->enabled_non_wakeup_gpios;
-
- /*
- * No need to generate IRQs for the rising edge for gpio IRQs
- * configured with falling edge only; and vice versa.
- */
- gen0 = l & bank->saved_fallingdetect;
- gen0 &= bank->saved_datain;
-
- gen1 = l & bank->saved_risingdetect;
- gen1 &= ~(bank->saved_datain);
-
- /* FIXME: Consider GPIO IRQs with level detections properly! */
- gen = l & (~(bank->saved_fallingdetect) &
- ~(bank->saved_risingdetect));
- /* Consider all GPIO IRQs needed to be updated */
- gen |= gen0 | gen1;
-
- if (gen) {
- u32 old0, old1;
-
- old0 = __raw_readl(bank->base +
- bank->regs->leveldetect0);
- old1 = __raw_readl(bank->base +
- bank->regs->leveldetect1);
-
- __raw_writel(old0, bank->base +
- bank->regs->leveldetect0);
- __raw_writel(old1, bank->base +
- bank->regs->leveldetect1);
- if (cpu_is_omap24xx() || cpu_is_omap34xx()) {
- old0 |= gen;
- old1 |= gen;
- }
-
- if (cpu_is_omap44xx()) {
- old0 |= l;
- old1 |= l;
- }
- __raw_writel(old0, bank->base +
- bank->regs->leveldetect0);
- __raw_writel(old1, bank->base +
- bank->regs->leveldetect1);
- }
+ if (IS_ERR_VALUE(pm_runtime_get_sync(bank->dev) < 0))
+ dev_err(bank->dev, "%s: GPIO bank %d "
+ "pm_runtime_get_sync failed\n",
+ __func__, bank->id);
}
}
@@ -1325,9 +1336,14 @@ static void omap_gpio_restore_context(struct gpio_bank *bank)
bank->base + bank->regs->fallingdetect);
__raw_writel(bank->context.dataout, bank->base + bank->regs->dataout);
}
+#else
+#define omap_gpio_runtime_suspend NULL
+#define omap_gpio_runtime_resume NULL
#endif
static const struct dev_pm_ops gpio_pm_ops = {
+ .runtime_suspend = omap_gpio_runtime_suspend,
+ .runtime_resume = omap_gpio_runtime_resume,
.suspend = omap_gpio_suspend,
.resume = omap_gpio_resume,
};
--
1.6.0.4
More information about the linux-arm-kernel
mailing list