[PATCH v2 6/6] arm: davinci: DA850: Add wl1271/wlan support
Ido Yariv
ido at wizery.com
Sun Jul 10 09:14:39 EDT 2011
The wl1271 daughter card for AM18x EVMs is a combo wireless connectivity
add-on card, based on the LS Research TiWi module with Texas
Instruments' wl1271 solution.
It is a 4-wire, 1.8V, embedded SDIO WLAN device with an external IRQ
line and is power-controlled by a GPIO-based fixed regulator.
This patch adds support for the WLAN capabilities of this expansion
board.
Signed-off-by: Ido Yariv <ido at wizery.com>
---
arch/arm/mach-davinci/Kconfig | 10 +++
arch/arm/mach-davinci/board-da850-evm.c | 127 +++++++++++++++++++++++++++++++
2 files changed, 137 insertions(+), 0 deletions(-)
diff --git a/arch/arm/mach-davinci/Kconfig b/arch/arm/mach-davinci/Kconfig
index c0deaca..32d837d 100644
--- a/arch/arm/mach-davinci/Kconfig
+++ b/arch/arm/mach-davinci/Kconfig
@@ -192,6 +192,16 @@ config DA850_UI_RMII
endchoice
+config DA850_WL12XX
+ bool "AM18x wl1271 daughter board"
+ depends on MACH_DAVINCI_DA850_EVM
+ help
+ The wl1271 daughter card for AM18x EVMs is a combo wireless
+ connectivity add-on card, based on the LS Research TiWi module with
+ Texas Instruments' wl1271 solution.
+ Say Y if you want to use a wl1271 expansion card connected to the
+ AM18x EVM.
+
config GPIO_PCA953X
default MACH_DAVINCI_DA850_EVM
diff --git a/arch/arm/mach-davinci/board-da850-evm.c b/arch/arm/mach-davinci/board-da850-evm.c
index a7b41bf..2dae1a1 100644
--- a/arch/arm/mach-davinci/board-da850-evm.c
+++ b/arch/arm/mach-davinci/board-da850-evm.c
@@ -31,6 +31,8 @@
#include <linux/input/tps6507x-ts.h>
#include <linux/spi/spi.h>
#include <linux/spi/flash.h>
+#include <linux/delay.h>
+#include <linux/wl12xx.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
@@ -49,6 +51,9 @@
#define DA850_MMCSD_CD_PIN GPIO_TO_PIN(4, 0)
#define DA850_MMCSD_WP_PIN GPIO_TO_PIN(4, 1)
+#define DA850_WLAN_EN GPIO_TO_PIN(6, 9)
+#define DA850_WLAN_IRQ GPIO_TO_PIN(6, 10)
+
#define DA850_MII_MDIO_CLKEN_PIN GPIO_TO_PIN(2, 6)
static struct mtd_partition da850evm_spiflash_part[] = {
@@ -1117,6 +1122,126 @@ static __init int da850_evm_init_cpufreq(void)
static __init int da850_evm_init_cpufreq(void) { return 0; }
#endif
+#ifdef CONFIG_DA850_WL12XX
+
+static int da850_wl12xx_fref = WL12XX_REFCLOCK_38;
+
+static int __init setup_da850_wl12xx_fref(char *fref)
+{
+ if (!strcmp(fref, "19.2"))
+ da850_wl12xx_fref = WL12XX_REFCLOCK_19;
+ else if (!strcmp(fref, "26"))
+ da850_wl12xx_fref = WL12XX_REFCLOCK_26;
+ else if (!strcmp(fref, "38.4"))
+ da850_wl12xx_fref = WL12XX_REFCLOCK_38;
+ else if (!strcmp(fref, "52"))
+ da850_wl12xx_fref = WL12XX_REFCLOCK_52;
+ else if (!strcmp(fref, "XTAL26"))
+ da850_wl12xx_fref = WL12XX_REFCLOCK_26_XTAL;
+ else if (!strcmp(fref, "XTAL38.4"))
+ da850_wl12xx_fref = WL12XX_REFCLOCK_38_XTAL;
+ else
+ pr_info("da850_wl12xx_fref is invalid. Valid options: "
+ "19.2, 26, 38.4, 52, XTAL26 or XTAL38.4\n");
+ return 0;
+}
+__setup("da850_wl12xx_fref=", setup_da850_wl12xx_fref);
+
+static void wl12xx_set_power(int slot, bool power_on)
+{
+ static bool power_state;
+
+ pr_debug("Powering %s wl12xx", power_on ? "on" : "off");
+
+ if (power_on == power_state)
+ return;
+ power_state = power_on;
+
+ if (power_on) {
+ /* Power up sequence required for wl127x devices */
+ gpio_set_value(DA850_WLAN_EN, 1);
+ usleep_range(15000, 15000);
+ gpio_set_value(DA850_WLAN_EN, 0);
+ usleep_range(1000, 1000);
+ gpio_set_value(DA850_WLAN_EN, 1);
+ msleep(70);
+ } else {
+ gpio_set_value(DA850_WLAN_EN, 0);
+ }
+}
+
+static struct davinci_mmc_config da850_mmc_wl12xx_config = {
+ .get_ro = NULL,
+ .get_cd = NULL,
+ .set_power = wl12xx_set_power,
+ .wires = 4,
+ .max_freq = 25000000,
+ .caps = MMC_CAP_4_BIT_DATA | MMC_CAP_NONREMOVABLE |
+ MMC_CAP_POWER_OFF_CARD,
+ .version = MMC_CTLR_VERSION_2,
+};
+
+static const short da850_evm_mmc_wl12xx_pins[] __initconst = {
+ DA850_MMCSD1_DAT_0, DA850_MMCSD1_DAT_1, DA850_MMCSD1_DAT_2,
+ DA850_MMCSD1_DAT_3, DA850_MMCSD1_CLK, DA850_MMCSD1_CMD,
+ DA850_GPIO6_9, DA850_GPIO6_10,
+ -1
+};
+
+static struct wl12xx_platform_data da850_wl12xx_wlan_data __initdata = {
+ .irq = -1,
+ .board_ref_clock = -1,
+ .platform_quirks = WL12XX_PLATFORM_QUIRK_EDGE_IRQ,
+};
+
+static void da850_wl12xx_init(void)
+{
+ int ret;
+
+ ret = davinci_cfg_reg_list(da850_evm_mmc_wl12xx_pins);
+ if (ret) {
+ pr_warning("da850_evm_init: wl12xx/mmc mux setup failed:"
+ " %d\n", ret);
+ return;
+ }
+
+ ret = da850_register_mmcsd1(&da850_mmc_wl12xx_config);
+ if (ret) {
+ pr_warning("da850_evm_init: wl12xx/mmc registration failed:"
+ " %d\n", ret);
+ return;
+ }
+
+ ret = gpio_request_one(DA850_WLAN_EN, GPIOF_OUT_INIT_LOW, "wl12xx_en");
+ if (ret) {
+ pr_err("Error initializing the wl12xx enable gpio: %d\n", ret);
+ return;
+ }
+
+ ret = gpio_request_one(DA850_WLAN_IRQ, GPIOF_IN, "wl12xx_irq");
+ if (ret) {
+ pr_err("Error initializing the wl12xx irq gpio: %d\n", ret);
+ gpio_free(DA850_WLAN_EN);
+ return;
+ }
+
+ da850_wl12xx_wlan_data.irq = gpio_to_irq(DA850_WLAN_IRQ);
+ da850_wl12xx_wlan_data.board_ref_clock = da850_wl12xx_fref;
+
+ ret = wl12xx_set_platform_data(&da850_wl12xx_wlan_data);
+ if (ret) {
+ pr_err("Error setting wl12xx data: %d\n", ret);
+ gpio_free(DA850_WLAN_IRQ);
+ gpio_free(DA850_WLAN_EN);
+ }
+}
+
+#else /* CONFIG_DA850_WL12XX */
+
+static void da850_wl12xx_init(void) { }
+
+#endif /* CONFIG_DA850_WL12XX */
+
static __init void da850_evm_init(void)
{
int ret;
@@ -1169,6 +1294,8 @@ static __init void da850_evm_init(void)
if (ret)
pr_warning("da850_evm_init: mmcsd0 registration failed:"
" %d\n", ret);
+
+ da850_wl12xx_init();
}
davinci_serial_init(&da850_evm_uart_config);
--
1.7.4.1
More information about the linux-arm-kernel
mailing list