[PATCH 2/6] pxa3xx_nand: rework irq logic
Lei Wen
leiwen at marvell.com
Fri Jul 8 10:56:35 EDT 2011
Enable all irq when we start the nand controller, and
put all the transaction logic in the pxa3xx_nand_irq.
By doing this way, we could dramatically increase the
performance by avoid unnecessary delay.
Signed-off-by: Lei Wen <leiwen at marvell.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang at marvell.com>
Cc: Eric Miao <eric.y.miao at gmail.com>
Cc: David Woodhouse <dwmw2 at infradead.org>
---
drivers/mtd/nand/pxa3xx_nand.c | 400 +++++++++++++++++++---------------------
1 files changed, 188 insertions(+), 212 deletions(-)
diff --git a/drivers/mtd/nand/pxa3xx_nand.c b/drivers/mtd/nand/pxa3xx_nand.c
index 6c0587b..dac522c 100644
--- a/drivers/mtd/nand/pxa3xx_nand.c
+++ b/drivers/mtd/nand/pxa3xx_nand.c
@@ -27,6 +27,7 @@
#include <plat/pxa3xx_nand.h>
#define CHIP_DELAY_TIMEOUT (2 * HZ/10)
+#define NAND_STOP_DELAY (2 * HZ/50)
/* registers and bit definitions */
#define NDCR (0x00) /* Control register */
@@ -52,16 +53,18 @@
#define NDCR_ND_MODE (0x3 << 21)
#define NDCR_NAND_MODE (0x0)
#define NDCR_CLR_PG_CNT (0x1 << 20)
-#define NDCR_CLR_ECC (0x1 << 19)
+#define NDCR_STOP_ON_UNCOR (0x1 << 19)
#define NDCR_RD_ID_CNT_MASK (0x7 << 16)
#define NDCR_RD_ID_CNT(x) (((x) << 16) & NDCR_RD_ID_CNT_MASK)
#define NDCR_RA_START (0x1 << 15)
#define NDCR_PG_PER_BLK (0x1 << 14)
#define NDCR_ND_ARB_EN (0x1 << 12)
+#define NDCR_INT_MASK (0xFFF)
#define NDSR_MASK (0xfff)
-#define NDSR_RDY (0x1 << 11)
+#define NDSR_RDY (0x1 << 12)
+#define NDSR_FLASH_RDY (0x1 << 11)
#define NDSR_CS0_PAGED (0x1 << 10)
#define NDSR_CS1_PAGED (0x1 << 9)
#define NDSR_CS0_CMDD (0x1 << 8)
@@ -104,13 +107,15 @@ enum {
};
enum {
- STATE_READY = 0,
+ STATE_IDLE = 0,
STATE_CMD_HANDLE,
STATE_DMA_READING,
STATE_DMA_WRITING,
STATE_DMA_DONE,
STATE_PIO_READING,
STATE_PIO_WRITING,
+ STATE_CMD_DONE,
+ STATE_READY,
};
struct pxa3xx_nand_info {
@@ -292,7 +297,48 @@ static void pxa3xx_set_datasize(struct pxa3xx_nand_info *info)
}
}
-static int prepare_read_prog_cmd(struct pxa3xx_nand_info *info,
+/**
+ * NOTE: it is a must to set ND_RUN firstly, then write
+ * command buffer, otherwise, it does not work.
+ * We enable all the interrupt at the same time, and
+ * let pxa3xx_nand_irq to handle all logic.
+ */
+static void pxa3xx_nand_start(struct pxa3xx_nand_info *info)
+{
+ uint32_t ndcr;
+
+ ndcr = info->reg_ndcr;
+ ndcr |= info->use_ecc ? NDCR_ECC_EN : 0;
+ ndcr |= info->use_dma ? NDCR_DMA_EN : 0;
+ ndcr |= NDCR_ND_RUN;
+
+ /* clear status bits and run */
+ nand_writel(info, NDCR, 0);
+ nand_writel(info, NDSR, NDSR_MASK);
+ nand_writel(info, NDCR, ndcr);
+}
+
+static void pxa3xx_nand_stop(struct pxa3xx_nand_info *info)
+{
+ uint32_t ndcr;
+ int timeout = NAND_STOP_DELAY;
+
+ /* wait RUN bit in NDCR become 0 */
+ ndcr = nand_readl(info, NDCR);
+ while ((ndcr & NDCR_ND_RUN) && (timeout -- > 0)) {
+ ndcr = nand_readl(info, NDCR);
+ udelay(1);
+ }
+
+ if (timeout <= 0) {
+ ndcr &= ~NDCR_ND_RUN;
+ nand_writel(info, NDCR, ndcr);
+ }
+ /* clear status bits */
+ nand_writel(info, NDSR, NDSR_MASK);
+}
+
+static void prepare_read_prog_cmd(struct pxa3xx_nand_info *info,
uint16_t cmd, int column, int page_addr)
{
const struct pxa3xx_nand_cmdset *cmdset = info->cmdset;
@@ -319,21 +365,18 @@ static int prepare_read_prog_cmd(struct pxa3xx_nand_info *info,
if (cmd == cmdset->program)
info->ndcb0 |= NDCB0_CMD_TYPE(1) | NDCB0_AUTO_RS;
-
- return 0;
}
-static int prepare_erase_cmd(struct pxa3xx_nand_info *info,
+static void prepare_erase_cmd(struct pxa3xx_nand_info *info,
uint16_t cmd, int page_addr)
{
info->ndcb0 = cmd | ((cmd & 0xff00) ? NDCB0_DBC : 0);
info->ndcb0 |= NDCB0_CMD_TYPE(2) | NDCB0_AUTO_RS | NDCB0_ADDR_CYC(3);
info->ndcb1 = page_addr;
info->ndcb2 = 0;
- return 0;
}
-static int prepare_other_cmd(struct pxa3xx_nand_info *info, uint16_t cmd)
+static void prepare_other_cmd(struct pxa3xx_nand_info *info, uint16_t cmd)
{
const struct pxa3xx_nand_cmdset *cmdset = info->cmdset;
@@ -343,7 +386,7 @@ static int prepare_other_cmd(struct pxa3xx_nand_info *info, uint16_t cmd)
info->oob_size = 0;
if (cmd == cmdset->read_id) {
- info->ndcb0 |= NDCB0_CMD_TYPE(3);
+ info->ndcb0 |= NDCB0_CMD_TYPE(3) | NDCB0_ADDR_CYC(1);
info->data_size = 8;
} else if (cmd == cmdset->read_status) {
info->ndcb0 |= NDCB0_CMD_TYPE(4);
@@ -352,9 +395,7 @@ static int prepare_other_cmd(struct pxa3xx_nand_info *info, uint16_t cmd)
cmd == cmdset->unlock) {
info->ndcb0 |= NDCB0_CMD_TYPE(5);
} else
- return -EINVAL;
-
- return 0;
+ BUG();
}
static void enable_int(struct pxa3xx_nand_info *info, uint32_t int_mask)
@@ -402,10 +443,8 @@ static int write_cmd(struct pxa3xx_nand_info *info)
return 0;
}
-static int handle_data_pio(struct pxa3xx_nand_info *info)
+static void handle_data_pio(struct pxa3xx_nand_info *info)
{
- int ret, timeout = CHIP_DELAY_TIMEOUT;
-
switch (info->state) {
case STATE_PIO_WRITING:
__raw_writesl(info->mmio_base + NDDB, info->data_buff,
@@ -413,14 +452,6 @@ static int handle_data_pio(struct pxa3xx_nand_info *info)
if (info->oob_size > 0)
__raw_writesl(info->mmio_base + NDDB, info->oob_buff,
DIV_ROUND_UP(info->oob_size, 4));
-
- enable_int(info, NDSR_CS0_BBD | NDSR_CS0_CMDD);
-
- ret = wait_for_completion_timeout(&info->cmd_complete, timeout);
- if (!ret) {
- printk(KERN_ERR "program command time out\n");
- return -1;
- }
break;
case STATE_PIO_READING:
__raw_readsl(info->mmio_base + NDDB, info->data_buff,
@@ -432,14 +463,11 @@ static int handle_data_pio(struct pxa3xx_nand_info *info)
default:
printk(KERN_ERR "%s: invalid state %d\n", __func__,
info->state);
- return -EINVAL;
+ BUG();
}
-
- info->state = STATE_READY;
- return 0;
}
-static void start_data_dma(struct pxa3xx_nand_info *info, int dir_out)
+static void start_data_dma(struct pxa3xx_nand_info *info)
{
struct pxa_dma_desc *desc = info->data_desc;
int dma_len = ALIGN(info->data_size + info->oob_size, 32);
@@ -447,14 +475,21 @@ static void start_data_dma(struct pxa3xx_nand_info *info, int dir_out)
desc->ddadr = DDADR_STOP;
desc->dcmd = DCMD_ENDIRQEN | DCMD_WIDTH4 | DCMD_BURST32 | dma_len;
- if (dir_out) {
+ switch (info->state) {
+ case STATE_DMA_WRITING:
desc->dsadr = info->data_buff_phys;
desc->dtadr = info->mmio_phys + NDDB;
desc->dcmd |= DCMD_INCSRCADDR | DCMD_FLOWTRG;
- } else {
+ break;
+ case STATE_DMA_READING:
desc->dtadr = info->data_buff_phys;
desc->dsadr = info->mmio_phys + NDDB;
desc->dcmd |= DCMD_INCTRGADDR | DCMD_FLOWSRC;
+ break;
+ default:
+ printk(KERN_ERR "%s: invalid state %d\n", __func__,
+ info->state);
+ BUG();
}
DRCMR(info->drcmr_dat) = DRCMR_MAPVLD | info->data_dma_ch;
@@ -472,93 +507,60 @@ static void pxa3xx_nand_data_dma_irq(int channel, void *data)
if (dcsr & DCSR_BUSERR) {
info->retcode = ERR_DMABUSERR;
- complete(&info->cmd_complete);
}
- if (info->state == STATE_DMA_WRITING) {
- info->state = STATE_DMA_DONE;
- enable_int(info, NDSR_CS0_BBD | NDSR_CS0_CMDD);
- } else {
- info->state = STATE_READY;
- complete(&info->cmd_complete);
- }
+ info->state = STATE_DMA_DONE;
+ enable_int(info, NDCR_INT_MASK);
+ nand_writel(info, NDSR, NDSR_WRDREQ | NDSR_RDDREQ);
}
static irqreturn_t pxa3xx_nand_irq(int irq, void *devid)
{
struct pxa3xx_nand_info *info = devid;
- unsigned int status;
+ unsigned int status, is_completed = 0;
status = nand_readl(info, NDSR);
- if (status & (NDSR_RDDREQ | NDSR_DBERR | NDSR_SBERR)) {
- if (status & NDSR_DBERR)
- info->retcode = ERR_DBERR;
- else if (status & NDSR_SBERR)
- info->retcode = ERR_SBERR;
-
- disable_int(info, NDSR_RDDREQ | NDSR_DBERR | NDSR_SBERR);
-
- if (info->use_dma) {
- info->state = STATE_DMA_READING;
- start_data_dma(info, 0);
- } else {
- info->state = STATE_PIO_READING;
- complete(&info->cmd_complete);
- }
- } else if (status & NDSR_WRDREQ) {
- disable_int(info, NDSR_WRDREQ);
+ if (status & NDSR_DBERR)
+ info->retcode = ERR_DBERR;
+ if (status & NDSR_SBERR)
+ info->retcode = ERR_SBERR;
+ if (status & (NDSR_RDDREQ | NDSR_WRDREQ)) {
+ /* whether use dma to transfer data */
if (info->use_dma) {
- info->state = STATE_DMA_WRITING;
- start_data_dma(info, 1);
+ disable_int(info, NDCR_INT_MASK);
+ info->state = (status & NDSR_RDDREQ) ?
+ STATE_DMA_READING : STATE_DMA_WRITING;
+ start_data_dma(info);
+ goto NORMAL_IRQ_EXIT;
} else {
- info->state = STATE_PIO_WRITING;
- complete(&info->cmd_complete);
+ info->state = (status & NDSR_RDDREQ) ?
+ STATE_PIO_READING : STATE_PIO_WRITING;
+ handle_data_pio(info);
}
- } else if (status & (NDSR_CS0_BBD | NDSR_CS0_CMDD)) {
- if (status & NDSR_CS0_BBD)
- info->retcode = ERR_BBERR;
-
- disable_int(info, NDSR_CS0_BBD | NDSR_CS0_CMDD);
- info->state = STATE_READY;
- complete(&info->cmd_complete);
}
- nand_writel(info, NDSR, status);
- return IRQ_HANDLED;
-}
-
-static int pxa3xx_nand_do_cmd(struct pxa3xx_nand_info *info, uint32_t event)
-{
- uint32_t ndcr;
- int ret, timeout = CHIP_DELAY_TIMEOUT;
-
- if (write_cmd(info)) {
- info->retcode = ERR_SENDCMD;
- goto fail_stop;
+ if (status & NDSR_CS0_CMDD) {
+ info->state = STATE_CMD_DONE;
+ is_completed = 1;
}
+ if (status & NDSR_FLASH_RDY)
+ info->state = STATE_READY;
- info->state = STATE_CMD_HANDLE;
-
- enable_int(info, event);
-
- ret = wait_for_completion_timeout(&info->cmd_complete, timeout);
- if (!ret) {
- printk(KERN_ERR "command execution timed out\n");
- info->retcode = ERR_SENDCMD;
- goto fail_stop;
+ if (status & NDSR_WRCMDREQ) {
+ nand_writel(info, NDSR, NDSR_WRCMDREQ);
+ status &= ~NDSR_WRCMDREQ;
+ info->state = STATE_CMD_HANDLE;
+ nand_writel(info, NDCB0, info->ndcb0);
+ nand_writel(info, NDCB0, info->ndcb1);
+ nand_writel(info, NDCB0, info->ndcb2);
}
- if (info->use_dma == 0 && info->data_size > 0)
- if (handle_data_pio(info))
- goto fail_stop;
-
- return 0;
-
-fail_stop:
- ndcr = nand_readl(info, NDCR);
- nand_writel(info, NDCR, ndcr & ~NDCR_ND_RUN);
- udelay(10);
- return -ETIMEDOUT;
+ /* clear NDSR to let the controller exit the IRQ */
+ nand_writel(info, NDSR, status);
+ if (is_completed)
+ complete(&info->cmd_complete);
+NORMAL_IRQ_EXIT:
+ return IRQ_HANDLED;
}
static int pxa3xx_nand_dev_ready(struct mtd_info *mtd)
@@ -580,14 +582,13 @@ static void pxa3xx_nand_cmdfunc(struct mtd_info *mtd, unsigned command,
{
struct pxa3xx_nand_info *info = mtd->priv;
const struct pxa3xx_nand_cmdset *cmdset = info->cmdset;
- int ret;
+ int ret, exec_cmd = 0;
info->use_dma = (use_dma) ? 1 : 0;
info->use_ecc = 0;
info->data_size = 0;
- info->state = STATE_READY;
-
- init_completion(&info->cmd_complete);
+ info->state = 0;
+ info->retcode = ERR_NONE;
switch (command) {
case NAND_CMD_READOOB:
@@ -596,36 +597,18 @@ static void pxa3xx_nand_cmdfunc(struct mtd_info *mtd, unsigned command,
info->buf_start = mtd->writesize + column;
memset(info->data_buff, 0xFF, info->buf_count);
- if (prepare_read_prog_cmd(info, cmdset->read1, column, page_addr))
- break;
-
- pxa3xx_nand_do_cmd(info, NDSR_RDDREQ | NDSR_DBERR | NDSR_SBERR);
-
- /* We only are OOB, so if the data has error, does not matter */
- if (info->retcode == ERR_DBERR)
- info->retcode = ERR_NONE;
+ prepare_read_prog_cmd(info, cmdset->read1, column, page_addr);
+ exec_cmd = 1;
break;
case NAND_CMD_READ0:
info->use_ecc = 1;
- info->retcode = ERR_NONE;
info->buf_start = column;
info->buf_count = mtd->writesize + mtd->oobsize;
memset(info->data_buff, 0xFF, info->buf_count);
- if (prepare_read_prog_cmd(info, cmdset->read1, column, page_addr))
- break;
-
- pxa3xx_nand_do_cmd(info, NDSR_RDDREQ | NDSR_DBERR | NDSR_SBERR);
-
- if (info->retcode == ERR_DBERR) {
- /* for blank page (all 0xff), HW will calculate its ECC as
- * 0, which is different from the ECC information within
- * OOB, ignore such double bit errors
- */
- if (is_buf_blank(info->data_buff, mtd->writesize))
- info->retcode = ERR_NONE;
- }
+ prepare_read_prog_cmd(info, cmdset->read1, column, page_addr);
+ exec_cmd = 1;
break;
case NAND_CMD_SEQIN:
info->buf_start = column;
@@ -639,17 +622,13 @@ static void pxa3xx_nand_cmdfunc(struct mtd_info *mtd, unsigned command,
case NAND_CMD_PAGEPROG:
info->use_ecc = (info->seqin_column >= mtd->writesize) ? 0 : 1;
- if (prepare_read_prog_cmd(info, cmdset->program,
- info->seqin_column, info->seqin_page_addr))
- break;
-
- pxa3xx_nand_do_cmd(info, NDSR_WRDREQ);
+ prepare_read_prog_cmd(info, cmdset->program,
+ info->seqin_column, info->seqin_page_addr);
+ exec_cmd = 1;
break;
case NAND_CMD_ERASE1:
- if (prepare_erase_cmd(info, cmdset->erase, page_addr))
- break;
-
- pxa3xx_nand_do_cmd(info, NDSR_CS0_BBD | NDSR_CS0_CMDD);
+ prepare_erase_cmd(info, cmdset->erase, page_addr);
+ exec_cmd = 1;
break;
case NAND_CMD_ERASE2:
break;
@@ -660,42 +639,72 @@ static void pxa3xx_nand_cmdfunc(struct mtd_info *mtd, unsigned command,
info->buf_count = (command == NAND_CMD_READID) ?
info->read_id_bytes : 1;
- if (prepare_other_cmd(info, (command == NAND_CMD_READID) ?
- cmdset->read_id : cmdset->read_status))
- break;
-
- pxa3xx_nand_do_cmd(info, NDSR_RDDREQ);
+ prepare_other_cmd(info, (command == NAND_CMD_READID) ?
+ cmdset->read_id : cmdset->read_status);
+ exec_cmd = 1;
break;
case NAND_CMD_RESET:
- if (prepare_other_cmd(info, cmdset->reset))
- break;
-
- ret = pxa3xx_nand_do_cmd(info, NDSR_CS0_CMDD);
- if (ret == 0) {
- int timeout = 2;
- uint32_t ndcr;
-
- while (timeout--) {
- if (nand_readl(info, NDSR) & NDSR_RDY)
- break;
- msleep(10);
- }
-
- ndcr = nand_readl(info, NDCR);
- nand_writel(info, NDCR, ndcr & ~NDCR_ND_RUN);
- }
+ prepare_other_cmd(info, cmdset->reset);
+ exec_cmd = 1;
break;
default:
printk(KERN_ERR "non-supported command.\n");
break;
}
- if (info->retcode == ERR_DBERR) {
- printk(KERN_ERR "double bit error @ page %08x\n", page_addr);
- info->retcode = ERR_NONE;
+ if (exec_cmd) {
+ init_completion(&info->cmd_complete);
+ pxa3xx_nand_start(info);
+
+ ret = wait_for_completion_timeout(&info->cmd_complete,
+ CHIP_DELAY_TIMEOUT);
+ if (!ret) {
+ printk(KERN_ERR "Wait time out!!!\n");
+ /* Stop State Machine for next command cycle */
+ pxa3xx_nand_stop(info);
+ }
+ info->state = STATE_IDLE;
}
}
+static void pxa3xx_nand_write_page_hwecc(struct mtd_info *mtd,
+ struct nand_chip *chip, const uint8_t *buf)
+{
+ chip->write_buf(mtd, buf, mtd->writesize);
+ chip->write_buf(mtd, chip->oob_poi, mtd->oobsize);
+}
+
+static int pxa3xx_nand_read_page_hwecc(struct mtd_info *mtd,
+ struct nand_chip *chip, uint8_t *buf, int page)
+{
+ struct pxa3xx_nand_info *info = mtd->priv;
+
+ chip->read_buf(mtd, buf, mtd->writesize);
+ chip->read_buf(mtd, chip->oob_poi, mtd->oobsize);
+
+ if (info->retcode == ERR_SBERR) {
+ switch (info->use_ecc) {
+ case 1:
+ mtd->ecc_stats.corrected ++;
+ break;
+ case 0:
+ default:
+ break;
+ }
+ }
+ else if (info->retcode == ERR_DBERR) {
+ /*
+ * for blank page (all 0xff), HW will calculate its ECC as
+ * 0, which is different from the ECC information within
+ * OOB, ignore such double bit errors
+ */
+ if (is_buf_blank(buf, mtd->writesize))
+ mtd->ecc_stats.failed++;
+ }
+
+ return 0;
+}
+
static uint8_t pxa3xx_nand_read_byte(struct mtd_info *mtd)
{
struct pxa3xx_nand_info *info = mtd->priv;
@@ -770,47 +779,13 @@ static int pxa3xx_nand_waitfunc(struct mtd_info *mtd, struct nand_chip *this)
return 0;
}
-static void pxa3xx_nand_ecc_hwctl(struct mtd_info *mtd, int mode)
-{
- return;
-}
-
-static int pxa3xx_nand_ecc_calculate(struct mtd_info *mtd,
- const uint8_t *dat, uint8_t *ecc_code)
-{
- return 0;
-}
-
-static int pxa3xx_nand_ecc_correct(struct mtd_info *mtd,
- uint8_t *dat, uint8_t *read_ecc, uint8_t *calc_ecc)
-{
- struct pxa3xx_nand_info *info = mtd->priv;
- /*
- * Any error include ERR_SEND_CMD, ERR_DBERR, ERR_BUSERR, we
- * consider it as a ecc error which will tell the caller the
- * read fail We have distinguish all the errors, but the
- * nand_read_ecc only check this function return value
- *
- * Corrected (single-bit) errors must also be noted.
- */
- if (info->retcode == ERR_SBERR)
- return 1;
- else if (info->retcode != ERR_NONE)
- return -1;
-
- return 0;
-}
-
static int __readid(struct pxa3xx_nand_info *info, uint32_t *id)
{
const struct pxa3xx_nand_cmdset *cmdset = info->cmdset;
uint32_t ndcr;
uint8_t id_buff[8];
- if (prepare_other_cmd(info, cmdset->read_id)) {
- printk(KERN_ERR "failed to prepare command\n");
- return -EINVAL;
- }
+ prepare_other_cmd(info, cmdset->read_id);
/* Send command */
if (write_cmd(info))
@@ -836,7 +811,7 @@ static int pxa3xx_nand_config_flash(struct pxa3xx_nand_info *info,
{
struct platform_device *pdev = info->pdev;
struct pxa3xx_nand_platform_data *pdata = pdev->dev.platform_data;
- uint32_t ndcr = 0x00000FFF; /* disable all interrupts */
+ uint32_t ndcr = 0x0; /* enable all interrupts */
if (f->page_size != 2048 && f->page_size != 512)
return -EINVAL;
@@ -888,11 +863,12 @@ static int pxa3xx_nand_detect_config(struct pxa3xx_nand_info *info)
info->reg_ndcr = ndcr;
info->cmdset = &default_cmdset;
- if (__readid(info, &id))
+ pxa3xx_nand_cmdfunc(info->mtd, NAND_CMD_READID, 0, 0);
+ id = *((uint16_t *)(info->data_buff));
+ if (id == 0)
return -ENODEV;
/* Lookup the flash id */
- id = (id >> 8) & 0xff; /* device id is byte 2 */
for (i = 0; nand_flash_ids[i].name != NULL; i++) {
if (id == nand_flash_ids[i].id) {
type = &nand_flash_ids[i];
@@ -935,8 +911,8 @@ static int pxa3xx_nand_detect_flash(struct pxa3xx_nand_info *info,
/* we use default timing to detect id */
f = DEFAULT_FLASH_TYPE;
pxa3xx_nand_config_flash(info, f);
- if (__readid(info, &id))
- goto fail_detect;
+ pxa3xx_nand_cmdfunc(info->mtd, NAND_CMD_READID, 0, 0);
+ id = *((uint16_t *)(info->data_buff));
for (i=0; i<ARRAY_SIZE(builtin_flash_types) + pdata->num_flash - 1; i++) {
/* we first choose the flash definition from platfrom */
@@ -954,7 +930,6 @@ static int pxa3xx_nand_detect_flash(struct pxa3xx_nand_info *info,
dev_warn(&info->pdev->dev,
"failed to detect configured nand flash; found %04x instead of\n",
id);
-fail_detect:
return -ENODEV;
}
@@ -1025,6 +1000,8 @@ static void pxa3xx_nand_init_mtd(struct mtd_info *mtd,
this->select_chip = pxa3xx_nand_select_chip;
this->dev_ready = pxa3xx_nand_dev_ready;
this->cmdfunc = pxa3xx_nand_cmdfunc;
+ this->ecc.read_page = pxa3xx_nand_read_page_hwecc;
+ this->ecc.write_page = pxa3xx_nand_write_page_hwecc;
this->read_word = pxa3xx_nand_read_word;
this->read_byte = pxa3xx_nand_read_byte;
this->read_buf = pxa3xx_nand_read_buf;
@@ -1032,9 +1009,6 @@ static void pxa3xx_nand_init_mtd(struct mtd_info *mtd,
this->verify_buf = pxa3xx_nand_verify_buf;
this->ecc.mode = NAND_ECC_HW;
- this->ecc.hwctl = pxa3xx_nand_ecc_hwctl;
- this->ecc.calculate = pxa3xx_nand_ecc_calculate;
- this->ecc.correct = pxa3xx_nand_ecc_correct;
this->ecc.size = info->page_size;
if (info->page_size == 2048)
@@ -1176,10 +1150,6 @@ static int pxa3xx_nand_remove(struct platform_device *pdev)
platform_set_drvdata(pdev, NULL);
- del_mtd_device(mtd);
-#ifdef CONFIG_MTD_PARTITIONS
- del_mtd_partitions(mtd);
-#endif
irq = platform_get_irq(pdev, 0);
if (irq >= 0)
free_irq(irq, info);
@@ -1197,7 +1167,13 @@ static int pxa3xx_nand_remove(struct platform_device *pdev)
clk_disable(info->clk);
clk_put(info->clk);
- kfree(mtd);
+ if (mtd) {
+ del_mtd_device(mtd);
+#ifdef CONFIG_MTD_PARTITIONS
+ del_mtd_partitions(mtd);
+#endif
+ kfree(mtd);
+ }
return 0;
}
@@ -1231,10 +1207,10 @@ static int pxa3xx_nand_probe(struct platform_device *pdev)
nr_parts = parse_mtd_partitions(info->mtd, probes, &parts, 0);
if (nr_parts)
- return add_mtd_partitions(mtd, parts, nr_parts);
+ return add_mtd_partitions(info->mtd, parts, nr_parts);
}
- return add_mtd_partitions(mtd, pdata->parts, pdata->nr_parts);
+ return add_mtd_partitions(info->mtd, pdata->parts, pdata->nr_parts);
#else
return 0;
#endif
@@ -1246,7 +1222,7 @@ static int pxa3xx_nand_suspend(struct platform_device *pdev, pm_message_t state)
struct pxa3xx_nand_info *info = platform_get_drvdata(pdev);
struct mtd_info *mtd = info->mtd;
- if (info->state != STATE_READY) {
+ if (info->state) {
dev_err(&pdev->dev, "driver busy, state = %d\n", info->state);
return -EAGAIN;
}
--
1.7.0.4
______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/
More information about the linux-arm-kernel
mailing list