[RFC PATCH 3/5] OMAP3: Beagle: Update beagle board file to use DT

[G, Manjunath Kondaiah]

On Wed, Jul 06, 2011 at 01:00:22PM -0600, Grant Likely wrote:
> On Thu, Jun 30, 2011 at 03:07:25PM +0500, G, Manjunath Kondaiah wrote:
> > 
> > The beagle board file is updated to use i2c nodes from device
> > tree data structures.
> > 
> > Signed-off-by: G, Manjunath Kondaiah <manjugk at ti.com>
> > ---
> >  arch/arm/mach-omap2/board-omap3beagle.c |   24 ++++++++++++++++++++----
> >  1 files changed, 20 insertions(+), 4 deletions(-)
> > 
> > diff --git a/arch/arm/mach-omap2/board-omap3beagle.c b/arch/arm/mach-omap2/board-omap3beagle.c
> > index 213c4cd..db494aa 100644
> > --- a/arch/arm/mach-omap2/board-omap3beagle.c
> > +++ b/arch/arm/mach-omap2/board-omap3beagle.c
> > @@ -20,6 +20,7 @@
> >  #include <linux/clk.h>
> >  #include <linux/io.h>
> >  #include <linux/of_platform.h>
> > +#include <linux/of_address.h>
> >  #include <linux/leds.h>
> >  #include <linux/gpio.h>
> >  #include <linux/input.h>
> > @@ -33,6 +34,7 @@
> >  
> >  #include <linux/regulator/machine.h>
> >  #include <linux/i2c/twl.h>
> > +#include <linux/irq.h>
> >  
> >  #include <mach/hardware.h>
> >  #include <asm/mach-types.h>
> > @@ -421,8 +423,8 @@ static int __init omap3_beagle_i2c_init(void)
> >  	omap3_pmic_init("twl4030", &beagle_twldata);
> >  	/* Bus 3 is attached to the DVI port where devices like the pico DLP
> >  	 * projector don't work reliably with 400kHz */
> > +#if !defined(CONFIG_OF)
> >  	omap_register_i2c_bus(3, 100, beagle_i2c_eeprom, ARRAY_SIZE(beagle_i2c_eeprom));
> > -#ifdef CONFIG_OF
> >  	omap_register_i2c_bus(2, 100, NULL, 0);
> >  #endif /* CONFIG_OF */
> >  	return 0;
> > @@ -565,11 +567,24 @@ static void __init beagle_opp_init(void)
> >  	return;
> >  }
> >  
> > +static struct of_device_id omap_dt_gic_match[] __initdata = {
> > +	{ .compatible = "ti,omap-gic", },
> > +	{}
> > +};
> > +
> > +static struct of_device_id omap_dt_match_table[] __initdata = {
> > +	{ .compatible = "ti,omap3-beagle", },
> > +	{}
> > +};
> > +
> >  static void __init omap3_beagle_init(void)
> >  {
> > -#ifdef CONFIG_OF
> > -	of_platform_prepare(NULL, NULL);
> > -#endif /* CONFIG_OF */
> > +	struct device_node *node;
> > +
> > +	node = of_find_matching_node_by_address(NULL, omap_dt_gic_match,
> > +						OMAP34XX_IC_BASE);
> > +	if (node)
> > +		irq_domain_add_simple(node, 0);
> >  
> >  	omap3_mux_init(board_mux, OMAP_PACKAGE_CBB);
> >  	omap3_beagle_init_rev();
> > @@ -597,6 +612,7 @@ static void __init omap3_beagle_init(void)
> >  
> >  	beagle_display_init();
> >  	beagle_opp_init();
> > +	of_platform_populate(NULL, omap_dt_match_table, NULL, NULL);
> 
> This is probably a loosing approach.  Until the DT stuff is stable on
> omap, you should avoid doing anything that might break existing board
> ports.  Instead, I recommend creating an board-omap3-dt.c board file,
> and pull in only the static beagle device registrations that you need
> to get up and running, then you can pull them back out as the beagle
> DT board support matures.
yes. that is the plan. I have mentioned the same in PATCH 0/5

-Manjunath