[PATCH v4 2/2] ARM: l2x0: Add OF based initialization
Grant Likely
grant.likely at secretlab.ca
Wed Jul 6 17:02:37 EDT 2011
On Wed, Jul 06, 2011 at 03:42:59PM -0500, Rob Herring wrote:
> From: Rob Herring <rob.herring at calxeda.com>
>
> This adds probing for ARM L2x0 cache controllers via device tree. Support
> includes the L210, L220, and PL310 controllers. The binding allows setting
> up cache RAM latencies and filter addresses (PL310 only).
>
> Signed-off-by: Rob Herring <rob.herring at calxeda.com>
Acked-by: Grant Likely <grant.likely at secretlab.ca>
By rights, this should go via the arm tree, but it depends on patches
that are already in devicetree/next. Arnd, how do you want to handle
this? I want to avoid rebasing devicetree/next.
g.
> ---
> Changes in v4:
> - Documentation fixes
> - Add "arm," prefix to bindings
> - Change filter-ranges binding values to <start length>
> - Refactor l2x0 and pl310 init into separate functions
> - Use new OF helpers to read u32 binding values.
>
> Documentation/devicetree/bindings/arm/l2cc.txt | 43 ++++++++++
> arch/arm/include/asm/hardware/cache-l2x0.h | 17 ++++
> arch/arm/mm/cache-l2x0.c | 103 ++++++++++++++++++++++++
> 3 files changed, 163 insertions(+), 0 deletions(-)
> create mode 100644 Documentation/devicetree/bindings/arm/l2cc.txt
>
> diff --git a/Documentation/devicetree/bindings/arm/l2cc.txt b/Documentation/devicetree/bindings/arm/l2cc.txt
> new file mode 100644
> index 0000000..ab5b3f0
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/arm/l2cc.txt
> @@ -0,0 +1,43 @@
> +* ARM L2 Cache Controller
> +
> +ARM cores often have a separate level 2 cache controller. There are various
> +implementations of the L2 cache controller with compatible programming models.
> +The ARM L2 cache representation in the device tree should be done as follows:
> +
> +Required properties:
> +
> +- compatible : should be one of:
> + "arm,pl310-cache"
> + "arm,l220-cache"
> + "arm,l210-cache"
> +- cache-unified : Specifies the cache is a unified cache.
> +- cache-level : Should be set to 2 for a level 2 cache.
> +- reg : Physical base address and size of cache controller's memory mapped
> + registers.
> +
> +Optional properties:
> +
> +- arm,data-latency : Cycles of latency for Data RAM accesses. Specifies 3 cells of
> + read, write and setup latencies. Minimum valid values are 1. Controllers
> + without setup latency control should use a value of 0.
> +- arm,tag-latency : Cycles of latency for Tag RAM accesses. Specifies 3 cells of
> + read, write and setup latencies. Controllers without setup latency control
> + should use 0. Controllers without separate read and write Tag RAM latency
> + values should only use the first cell.
> +- arm,dirty-latency : Cycles of latency for Dirty RAMs. This is a single cell.
> +- arm,filter-ranges : <start length> Starting address and length of window to
> + filter. Addresses in the filter window are directed to the M1 port. Other
> + addresses will go to the M0 port.
> +
> +Example:
> +
> +L2: cache-controller {
> + compatible = "arm,pl310-cache";
> + reg = <0xfff12000 0x1000>;
> + arm,data-latency = <1 1 1>;
> + arm,tag-latency = <2 2 2>;
> + arm,filter-latency = <0x80000000 0x8000000>;
> + cache-unified;
> + cache-level = <2>;
> +};
> +
> diff --git a/arch/arm/include/asm/hardware/cache-l2x0.h b/arch/arm/include/asm/hardware/cache-l2x0.h
> index 16bd480..8fe149f 100644
> --- a/arch/arm/include/asm/hardware/cache-l2x0.h
> +++ b/arch/arm/include/asm/hardware/cache-l2x0.h
> @@ -47,6 +47,8 @@
> #define L2X0_CLEAN_INV_WAY 0x7FC
> #define L2X0_LOCKDOWN_WAY_D 0x900
> #define L2X0_LOCKDOWN_WAY_I 0x904
> +#define L2X0_ADDR_FILTER_START 0xC00
> +#define L2X0_ADDR_FILTER_END 0xC04
> #define L2X0_TEST_OPERATION 0xF00
> #define L2X0_LINE_DATA 0xF10
> #define L2X0_LINE_TAG 0xF30
> @@ -62,6 +64,14 @@
> #define L2X0_CACHE_ID_PART_L310 (3 << 6)
>
> #define L2X0_AUX_CTRL_MASK 0xc0000fff
> +#define L2X0_AUX_CTRL_DATA_RD_LATENCY_SHIFT 0
> +#define L2X0_AUX_CTRL_DATA_RD_LATENCY_MASK 0x7
> +#define L2X0_AUX_CTRL_DATA_WR_LATENCY_SHIFT 3
> +#define L2X0_AUX_CTRL_DATA_WR_LATENCY_MASK (0x7 << 3)
> +#define L2X0_AUX_CTRL_TAG_LATENCY_SHIFT 6
> +#define L2X0_AUX_CTRL_TAG_LATENCY_MASK (0x7 << 6)
> +#define L2X0_AUX_CTRL_DIRTY_LATENCY_SHIFT 9
> +#define L2X0_AUX_CTRL_DIRTY_LATENCY_MASK (0x7 << 9)
> #define L2X0_AUX_CTRL_ASSOCIATIVITY_SHIFT 16
> #define L2X0_AUX_CTRL_WAY_SIZE_SHIFT 17
> #define L2X0_AUX_CTRL_WAY_SIZE_MASK (0x3 << 17)
> @@ -72,8 +82,15 @@
> #define L2X0_AUX_CTRL_INSTR_PREFETCH_SHIFT 29
> #define L2X0_AUX_CTRL_EARLY_BRESP_SHIFT 30
>
> +#define L2X0_LATENCY_CTRL_SETUP_SHIFT 0
> +#define L2X0_LATENCY_CTRL_RD_SHIFT 4
> +#define L2X0_LATENCY_CTRL_WR_SHIFT 8
> +
> +#define L2X0_ADDR_FILTER_EN 1
> +
> #ifndef __ASSEMBLY__
> extern void __init l2x0_init(void __iomem *base, __u32 aux_val, __u32 aux_mask);
> +extern int l2x0_of_init(__u32 aux_val, __u32 aux_mask);
> #endif
>
> #endif
> diff --git a/arch/arm/mm/cache-l2x0.c b/arch/arm/mm/cache-l2x0.c
> index ef59099..274dc54 100644
> --- a/arch/arm/mm/cache-l2x0.c
> +++ b/arch/arm/mm/cache-l2x0.c
> @@ -16,9 +16,12 @@
> * along with this program; if not, write to the Free Software
> * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
> */
> +#include <linux/err.h>
> #include <linux/init.h>
> #include <linux/spinlock.h>
> #include <linux/io.h>
> +#include <linux/of.h>
> +#include <linux/of_address.h>
>
> #include <asm/cacheflush.h>
> #include <asm/hardware/cache-l2x0.h>
> @@ -344,3 +347,103 @@ void __init l2x0_init(void __iomem *base, __u32 aux_val, __u32 aux_mask)
> printk(KERN_INFO "l2x0: %d ways, CACHE_ID 0x%08x, AUX_CTRL 0x%08x, Cache size: %d B\n",
> ways, cache_id, aux, l2x0_size);
> }
> +
> +#ifdef CONFIG_OF
> +static void __init l2x0_of_setup(const struct device_node *np,
> + __u32 *aux_val, __u32 *aux_mask)
> +{
> + u32 data[2] = { 0, 0 };
> + u32 tag = 0;
> + u32 dirty = 0;
> + u32 val = 0, mask = 0;
> +
> + of_property_read_u32(np, "arm,tag-latency", &tag);
> + if (tag) {
> + mask |= L2X0_AUX_CTRL_TAG_LATENCY_MASK;
> + val |= (tag - 1) << L2X0_AUX_CTRL_TAG_LATENCY_SHIFT;
> + }
> +
> + of_property_read_u32_array(np, "arm,data-latency",
> + data, ARRAY_SIZE(data));
> + if (data[0] && data[1]) {
> + mask |= L2X0_AUX_CTRL_DATA_RD_LATENCY_MASK |
> + L2X0_AUX_CTRL_DATA_WR_LATENCY_MASK;
> + val |= ((data[0] - 1) << L2X0_AUX_CTRL_DATA_RD_LATENCY_SHIFT) |
> + ((data[1] - 1) << L2X0_AUX_CTRL_DATA_WR_LATENCY_SHIFT);
> + }
> +
> + of_property_read_u32(np, "arm,dirty-latency", &dirty);
> + if (dirty) {
> + mask |= L2X0_AUX_CTRL_DIRTY_LATENCY_MASK;
> + val |= (dirty - 1) << L2X0_AUX_CTRL_DIRTY_LATENCY_SHIFT;
> + }
> +
> + *aux_val &= ~mask;
> + *aux_val |= val;
> + *aux_mask &= ~mask;
> +}
> +
> +static void __init pl310_of_setup(const struct device_node *np,
> + __u32 *aux_val, __u32 *aux_mask)
> +{
> + u32 data[3] = { 0, 0, 0 };
> + u32 tag[3] = { 0, 0, 0 };
> + u32 filter[2] = { 0, 0 };
> +
> + of_property_read_u32_array(np, "arm,tag-latency", tag, ARRAY_SIZE(tag));
> + if (tag[0] && tag[1] && tag[2])
> + writel_relaxed(
> + ((tag[0] - 1) << L2X0_LATENCY_CTRL_RD_SHIFT) |
> + ((tag[1] - 1) << L2X0_LATENCY_CTRL_WR_SHIFT) |
> + ((tag[2] - 1) << L2X0_LATENCY_CTRL_SETUP_SHIFT),
> + l2x0_base + L2X0_TAG_LATENCY_CTRL);
> +
> + of_property_read_u32_array(np, "arm,data-latency",
> + data, ARRAY_SIZE(data));
> + if (data[0] && data[1] && data[2])
> + writel_relaxed(
> + ((data[0] - 1) << L2X0_LATENCY_CTRL_RD_SHIFT) |
> + ((data[1] - 1) << L2X0_LATENCY_CTRL_WR_SHIFT) |
> + ((data[2] - 1) << L2X0_LATENCY_CTRL_SETUP_SHIFT),
> + l2x0_base + L2X0_DATA_LATENCY_CTRL);
> +
> + of_property_read_u32_array(np, "arm,filter-ranges",
> + filter, ARRAY_SIZE(filter));
> + if (filter[0] && filter[1]) {
> + writel_relaxed(ALIGN(filter[0] + filter[1], SZ_1M),
> + l2x0_base + L2X0_ADDR_FILTER_END);
> + writel_relaxed((filter[0] & ~(SZ_1M - 1)) | L2X0_ADDR_FILTER_EN,
> + l2x0_base + L2X0_ADDR_FILTER_START);
> + }
> +}
> +
> +static const struct of_device_id l2x0_ids[] __initconst = {
> + { .compatible = "arm,pl310-cache", .data = pl310_of_setup },
> + { .compatible = "arm,l220-cache", .data = l2x0_of_setup },
> + { .compatible = "arm,l210-cache", .data = l2x0_of_setup },
> + {}
> +};
> +
> +int __init l2x0_of_init(__u32 aux_val, __u32 aux_mask)
> +{
> + struct device_node *np;
> + void (*l2_setup)(const struct device_node *np,
> + __u32 *aux_val, __u32 *aux_mask);
> +
> + np = of_find_matching_node(NULL, l2x0_ids);
> + if (!np)
> + return -ENODEV;
> + l2x0_base = of_iomap(np, 0);
> + if (!l2x0_base)
> + return -ENOMEM;
> +
> + /* L2 configuration can only be changed if the cache is disabled */
> + if (!(readl_relaxed(l2x0_base + L2X0_CTRL) & 1)) {
> + l2_setup = of_match_node(l2x0_ids, np)->data;
> + if (l2_setup)
> + l2_setup(np, &aux_val, &aux_mask);
> + }
> + l2x0_init(l2x0_base, aux_val, aux_mask);
> + return 0;
> +}
> +#endif
> --
> 1.7.4.1
>
More information about the linux-arm-kernel
mailing list