[PATCH v2 11/13] da850: pruss SUART board specific additions.

[Michael Williamson]

Hi Subhasish,

On 2/11/2011 9:51 AM, Subhasish Ghosh wrote:

> This patch adds the pruss SUART pin mux and registers the device
> with the pruss mfd driver.
> 
> Signed-off-by: Subhasish Ghosh <subhasish at mistralsolutions.com>
> ---
>  arch/arm/mach-davinci/board-da850-evm.c |   36 +++++++++++++++++++++++++++++++
>  1 files changed, 36 insertions(+), 0 deletions(-)
> 
> diff --git a/arch/arm/mach-davinci/board-da850-evm.c b/arch/arm/mach-davinci/board-da850-evm.c
> index f9c38f8..3858516 100644
> --- a/arch/arm/mach-davinci/board-da850-evm.c
> +++ b/arch/arm/mach-davinci/board-da850-evm.c
> @@ -1060,6 +1060,25 @@ const short da850_evm_pruss_can_pins[] = {
>  	-1
>  };
>  
> +const short da850_evm_pruss_suart_pins[] = {
> +	DA850_AHCLKX, DA850_ACLKX, DA850_AFSX,
> +	DA850_AHCLKR, DA850_ACLKR, DA850_AFSR,
> +	DA850_AXR_13, DA850_AXR_9, DA850_AXR_7,
> +	DA850_AXR_14, DA850_AXR_10, DA850_AXR_8,
> +	-1
> +};
> +


Shouldn't this pins select PRU[0,1]_XXX type functions and not McASP functions?
E.G.: PRU0_R31[17] instead of AHCLKX, PRU0_R31[18] instead of AHCLKR, etc.

> +static int __init da850_evm_setup_pruss_suart(void)
> +{
> +	int ret;
> +
> +	ret = davinci_cfg_reg_list(da850_evm_pruss_suart_pins);
> +	if (ret)
> +		pr_warning("%s: da850_evm_pruss_suart_pins "
> +			"mux setup failed: %d\n", __func__, ret);
> +	return ret;
> +}
> +
>  static int __init da850_evm_setup_pruss_can(void)
>  {
>  	int ret, val = 0;
> @@ -1085,6 +1104,17 @@ static int __init da850_evm_setup_pruss_can(void)
>  	return ret;
>  }
>  
> +static struct da850_evm_pruss_suart_data suart_data = {
> +	.version	= 1,
> +	.resource	= {
> +			.name	= "da8xx_mcasp0_iomem",
> +			.start	= DAVINCI_DA8XX_MCASP0_REG_BASE,
> +			.end	= DAVINCI_DA8XX_MCASP0_REG_BASE +
> +					(SZ_1K * 12) - 1,
> +			.flags	= IORESOURCE_MEM,
> +		},
> +};
> +
>  static struct da8xx_pruss_can_data can_data = {
>  	.version	= 1,
>  };
> @@ -1094,6 +1124,12 @@ static struct da8xx_pruss_devices pruss_devices[] = {
>  		.dev_name	= "da8xx_pruss_can",
>  		.pdata		= &can_data,
>  		.pdata_size	= sizeof(can_data),
> +		.setup		= da850_evm_setup_pruss_suart,


Should this be da850_evm_setup_pruss_can instead?

> +	},
> +	{
> +		.dev_name	= "da8xx_pruss_uart",
> +		.pdata		= &suart_data,
> +		.pdata_size	= sizeof(suart_data),
>  		.setup		= da850_evm_setup_pruss_can,


Should this be da850_evm_setup_pruss_suart instead?

>  	},
>  	{


-Mike