[PATCH v2 7/7] input: serio: ams-delta: toggle keyboard power over GPIO
Janusz Krzysztofik
jkrzyszt at tis.icnet.pl
Mon Dec 19 18:08:57 EST 2011
Don't use Amstrad Delta custom I/O functions once GPIO interface is
available for the underlying hardware.
While requesting and initializing GPIO pins used, also take care of one
extra pin KEYBRD_DATAOUT which, even if not used by the driver, belongs
to the device and affects its functioning.
Once done, move the driver initialization back to the device_initcall
level, reverting the temporary chane introduced with patch 1/7 "ARM:
OMAP1: ams-delta: register latch dependent devices from late_initcall".
That change is no longer required once the driver takes care of
registering used GPIO pins, and it's better to initialize the device
before others using the latch2 based GPIO pins, otherwise a garbage is
reported on boot, perhaps due to random data already captured by the FIQ
handler while the keyboard related latch bits are written with random
values during initialization of those other latch2 dependent devices.
Depends on patch 2/7 "ARM: OMAP1: ams-delta: convert latches to
basic_mmio_gpio"
Signed-off-by: Janusz Krzysztofik <jkrzyszt at tis.icnet.pl>
---
Changes against initial version:
* was 9/10,
* rebased on top of v2 of patch 2/7, just in case,
* moved AMS_DELTA_GPIO_PIN_KEYBRD_DATAOUT pin handling from the board
code to the driver,
* reverted a temporary change to the driver initcall level, introduced
by the new solution provided with patch 1/7.
arch/arm/mach-omap1/board-ams-delta.c | 10 ----
arch/arm/plat-omap/include/plat/board-ams-delta.h | 2 -
drivers/input/serio/ams_delta_serio.c | 55 ++++++++++++---------
3 files changed, 31 insertions(+), 36 deletions(-)
diff --git a/arch/arm/mach-omap1/board-ams-delta.c b/arch/arm/mach-omap1/board-ams-delta.c
index 3aba8f9..673cf21 100644
--- a/arch/arm/mach-omap1/board-ams-delta.c
+++ b/arch/arm/mach-omap1/board-ams-delta.c
@@ -227,16 +227,6 @@ static struct gpio latch_gpios[] __initconst = {
.label = "dockit2",
},
{
- .gpio = AMS_DELTA_GPIO_PIN_KEYBRD_PWR,
- .flags = GPIOF_OUT_INIT_LOW,
- .label = "keybrd_pwr",
- },
- {
- .gpio = AMS_DELTA_GPIO_PIN_KEYBRD_DATAOUT,
- .flags = GPIOF_OUT_INIT_LOW,
- .label = "keybrd_dataout",
- },
- {
.gpio = AMS_DELTA_GPIO_PIN_SCARD_RSTIN,
.flags = GPIOF_OUT_INIT_LOW,
.label = "scard_rstin",
diff --git a/arch/arm/plat-omap/include/plat/board-ams-delta.h b/arch/arm/plat-omap/include/plat/board-ams-delta.h
index e9ad673..027e79e 100644
--- a/arch/arm/plat-omap/include/plat/board-ams-delta.h
+++ b/arch/arm/plat-omap/include/plat/board-ams-delta.h
@@ -28,8 +28,6 @@
#if defined (CONFIG_MACH_AMS_DELTA)
-#define AMD_DELTA_LATCH2_KEYBRD_PWR 0x0100
-#define AMD_DELTA_LATCH2_KEYBRD_DATA 0x0200
#define AMD_DELTA_LATCH2_SCARD_RSTIN 0x0400
#define AMD_DELTA_LATCH2_SCARD_CMDVCC 0x0800
#define AMS_DELTA_LATCH2_MODEM_NRESET 0x1000
diff --git a/drivers/input/serio/ams_delta_serio.c b/drivers/input/serio/ams_delta_serio.c
index 56ffd7c..ef1ec40 100644
--- a/drivers/input/serio/ams_delta_serio.c
+++ b/drivers/input/serio/ams_delta_serio.c
@@ -92,8 +92,7 @@ static irqreturn_t ams_delta_serio_interrupt(int irq, void *dev_id)
static int ams_delta_serio_open(struct serio *serio)
{
/* enable keyboard */
- ams_delta_latch2_write(AMD_DELTA_LATCH2_KEYBRD_PWR,
- AMD_DELTA_LATCH2_KEYBRD_PWR);
+ gpio_set_value(AMS_DELTA_GPIO_PIN_KEYBRD_PWR, 1);
return 0;
}
@@ -101,9 +100,32 @@ static int ams_delta_serio_open(struct serio *serio)
static void ams_delta_serio_close(struct serio *serio)
{
/* disable keyboard */
- ams_delta_latch2_write(AMD_DELTA_LATCH2_KEYBRD_PWR, 0);
+ gpio_set_value(AMS_DELTA_GPIO_PIN_KEYBRD_PWR, 0);
}
+static struct gpio _gpios[] __initconst_or_module = {
+ {
+ .gpio = AMS_DELTA_GPIO_PIN_KEYBRD_DATA,
+ .flags = GPIOF_DIR_IN,
+ .label = "serio-data",
+ },
+ {
+ .gpio = AMS_DELTA_GPIO_PIN_KEYBRD_CLK,
+ .flags = GPIOF_DIR_IN,
+ .label = "serio-clock",
+ },
+ {
+ .gpio = AMS_DELTA_GPIO_PIN_KEYBRD_PWR,
+ .flags = GPIOF_OUT_INIT_LOW,
+ .label = "serio-power",
+ },
+ {
+ .gpio = AMS_DELTA_GPIO_PIN_KEYBRD_DATAOUT,
+ .flags = GPIOF_OUT_INIT_LOW,
+ .label = "serio-dataout",
+ },
+};
+
static int __init ams_delta_serio_init(void)
{
int err;
@@ -123,19 +145,11 @@ static int __init ams_delta_serio_init(void)
strlcpy(ams_delta_serio->phys, "GPIO/serio0",
sizeof(ams_delta_serio->phys));
- err = gpio_request(AMS_DELTA_GPIO_PIN_KEYBRD_DATA, "serio-data");
+ err = gpio_request_array(_gpios, ARRAY_SIZE(_gpios));
if (err) {
- pr_err("ams_delta_serio: Couldn't request gpio pin for data\n");
+ pr_err("ams_delta_serio: Couldn't request gpio pins\n");
goto serio;
}
- gpio_direction_input(AMS_DELTA_GPIO_PIN_KEYBRD_DATA);
-
- err = gpio_request(AMS_DELTA_GPIO_PIN_KEYBRD_CLK, "serio-clock");
- if (err) {
- pr_err("ams_delta_serio: couldn't request gpio pin for clock\n");
- goto gpio_data;
- }
- gpio_direction_input(AMS_DELTA_GPIO_PIN_KEYBRD_CLK);
err = request_irq(gpio_to_irq(AMS_DELTA_GPIO_PIN_KEYBRD_CLK),
ams_delta_serio_interrupt, IRQ_TYPE_EDGE_RISING,
@@ -143,7 +157,7 @@ static int __init ams_delta_serio_init(void)
if (err < 0) {
pr_err("ams_delta_serio: couldn't request gpio interrupt %d\n",
gpio_to_irq(AMS_DELTA_GPIO_PIN_KEYBRD_CLK));
- goto gpio_clk;
+ goto gpio;
}
/*
* Since GPIO register handling for keyboard clock pin is performed
@@ -157,25 +171,18 @@ static int __init ams_delta_serio_init(void)
dev_info(&ams_delta_serio->dev, "%s\n", ams_delta_serio->name);
return 0;
-gpio_clk:
- gpio_free(AMS_DELTA_GPIO_PIN_KEYBRD_CLK);
-gpio_data:
- gpio_free(AMS_DELTA_GPIO_PIN_KEYBRD_DATA);
+gpio:
+ gpio_free_array(_gpios, ARRAY_SIZE(_gpios));
serio:
kfree(ams_delta_serio);
return err;
}
-#ifndef MODULE
-late_initcall(ams_delta_serio_init);
-#else
module_init(ams_delta_serio_init);
static void __exit ams_delta_serio_exit(void)
{
serio_unregister_port(ams_delta_serio);
free_irq(OMAP_GPIO_IRQ(AMS_DELTA_GPIO_PIN_KEYBRD_CLK), 0);
- gpio_free(AMS_DELTA_GPIO_PIN_KEYBRD_CLK);
- gpio_free(AMS_DELTA_GPIO_PIN_KEYBRD_DATA);
+ gpio_free_array(_gpios, ARRAY_SIZE(_gpios));
}
module_exit(ams_delta_serio_exit);
-#endif
--
1.7.3.4
More information about the linux-arm-kernel
mailing list