[PATCH] ARM: OMAP3LOGIC: Adding DSS support
Alex
alexg at meprolight.com
Thu Dec 8 07:05:48 EST 2011
This patch adds DSS2 support to the LogicPD OMAP 35x Torpedo boardfile. LCD and
TV-out are supported.
Signed-off-by: Alex Gershgorin <alexg at meprolight.com>
---
arch/arm/mach-omap2/board-omap3logic.c | 151 ++++++++++++++++++++++++++++++++
1 files changed, 151 insertions(+), 0 deletions(-)
diff --git a/arch/arm/mach-omap2/board-omap3logic.c b/arch/arm/mach-omap2/board-omap3logic.c
index 7c0f193..86175fa 100644
--- a/arch/arm/mach-omap2/board-omap3logic.c
+++ b/arch/arm/mach-omap2/board-omap3logic.c
@@ -7,6 +7,9 @@
* Copyright (C) 2010 Logic Product Development, Inc.
* Peter Barada <peter.barada at logicpd.com>
*
+ * Copyright (C) 2011 Meprolight, Ltd.
+ * Alex Gershgorin <alexg at meprolight.com>
+ *
* Modified from Beagle, EVM, and RX51
*
* This program is free software; you can redistribute it and/or modify
@@ -44,6 +47,10 @@
#include <plat/gpmc-smsc911x.h>
#include <plat/gpmc.h>
#include <plat/sdrc.h>
+#include <plat/vram.h>
+
+#include <video/omapdss.h>
+#include <video/omap-panel-generic-dpi.h>
#define OMAP3LOGIC_SMSC911X_CS 1
@@ -58,6 +65,14 @@ static struct regulator_consumer_supply omap3logic_vmmc1_supply[] = {
REGULATOR_SUPPLY("vmmc", "omap_hsmmc.0"),
};
+static struct regulator_consumer_supply omap3logic_vdds_supplies[] = {
+ REGULATOR_SUPPLY("vdds_sdi", "omapdss"),
+ REGULATOR_SUPPLY("vdds_dsi", "omapdss"),
+};
+
+static struct regulator_consumer_supply omap3logic_vdac_supply =
+ REGULATOR_SUPPLY("vdda_dac", "omapdss_venc");
+
/* VMMC1 for MMC1 pins CMD, CLK, DAT0..DAT3 (20 mA, plus card == max 220 mA) */
static struct regulator_init_data omap3logic_vmmc1 = {
.constraints = {
@@ -74,6 +89,34 @@ static struct regulator_init_data omap3logic_vmmc1 = {
.consumer_supplies = omap3logic_vmmc1_supply,
};
+static struct regulator_init_data omap3logic_vpll2 = {
+ .constraints = {
+ .name = "VDDS_DSI",
+ .min_uV = 1800000,
+ .max_uV = 1800000,
+ .apply_uV = true,
+ .always_on = true,
+ .valid_modes_mask = REGULATOR_MODE_NORMAL
+ | REGULATOR_MODE_STANDBY,
+ .valid_ops_mask = REGULATOR_CHANGE_MODE,
+ },
+ .num_consumer_supplies = ARRAY_SIZE(omap3logic_vdds_supplies),
+ .consumer_supplies = omap3logic_vdds_supplies,
+};
+
+static struct regulator_init_data omap3logic_vdac = {
+ .constraints = {
+ .min_uV = 1800000,
+ .max_uV = 1800000,
+ .valid_modes_mask = REGULATOR_MODE_NORMAL
+ | REGULATOR_MODE_STANDBY,
+ .valid_ops_mask = REGULATOR_CHANGE_MODE
+ | REGULATOR_CHANGE_STATUS,
+ },
+ .num_consumer_supplies = 1,
+ .consumer_supplies = &omap3logic_vdac_supply,
+};
+
static struct twl4030_gpio_platform_data omap3logic_gpio_data = {
.gpio_base = OMAP_MAX_GPIO_LINES,
.irq_base = TWL4030_GPIO_IRQ_BASE,
@@ -91,6 +134,8 @@ static struct twl4030_platform_data omap3logic_twldata = {
/* platform_data for children goes here */
.gpio = &omap3logic_gpio_data,
.vmmc1 = &omap3logic_vmmc1,
+ .vpll2 = &omap3logic_vpll2,
+ .vdac = &omap3logic_vdac,
};
static int __init omap3logic_i2c_init(void)
@@ -182,6 +227,110 @@ static inline void __init board_smsc911x_init(void)
gpmc_smsc911x_init(&board_smsc911x_data);
}
+#if defined(CONFIG_FB_OMAP2) || defined(CONFIG_FB_OMAP2_MODULE)
+
+#define OMAP3_TORPEDO_LCD_BACKLIGHT_GPIO 154
+#define OMAP3_TORPEDO_LCD_ENABLE_GPIO 155
+#define OMAP3_TORPEDO_LCD_PWM_GPIO 56
+
+static struct gpio omap3logic_dss_gpios[] __initdata = {
+ {OMAP3_TORPEDO_LCD_BACKLIGHT_GPIO, GPIOF_OUT_INIT_LOW, "lcd_bl_pwr"},
+ {OMAP3_TORPEDO_LCD_PWM_GPIO, GPIOF_OUT_INIT_LOW, "lcd bl enable"},
+ {OMAP3_TORPEDO_LCD_ENABLE_GPIO, GPIOF_OUT_INIT_LOW, "lcd enable"},
+};
+
+static int omap3logic_enable_lcd(struct omap_dss_device *dssdev)
+{
+ gpio_set_value_cansleep(OMAP3_TORPEDO_LCD_ENABLE_GPIO, 1);
+ msleep(20);
+ gpio_set_value_cansleep(OMAP3_TORPEDO_LCD_BACKLIGHT_GPIO, 1);
+
+ return 0;
+}
+
+static void omap3logic_disable_lcd(struct omap_dss_device *dssdev)
+{
+ gpio_set_value_cansleep(OMAP3_TORPEDO_LCD_ENABLE_GPIO, 0);
+ msleep(20);
+ gpio_set_value_cansleep(OMAP3_TORPEDO_LCD_BACKLIGHT_GPIO, 0);
+}
+
+static struct panel_generic_dpi_data lcd_panel = {
+ .name = "sharp_lq",
+ .platform_enable = omap3logic_enable_lcd,
+ .platform_disable = omap3logic_disable_lcd,
+};
+
+static struct omap_dss_device omap3logic_lcd_device = {
+ .name = "lcd",
+ .driver_name = "generic_dpi_panel",
+ .type = OMAP_DISPLAY_TYPE_DPI,
+ .data = &lcd_panel,
+ .phy.dpi.data_lines = 16,
+};
+
+static struct omap_dss_device omap3logic_tv_device = {
+ .name = "tv",
+ .driver_name = "venc",
+ .type = OMAP_DISPLAY_TYPE_VENC,
+ .phy.venc.type = OMAP_DSS_VENC_TYPE_SVIDEO,
+};
+
+static struct omap_dss_device *omap3logic_dss_devices[] = {
+ &omap3logic_lcd_device,
+ &omap3logic_tv_device,
+};
+
+static struct omap_dss_board_info omap3logic_dss_data = {
+ .num_devices = ARRAY_SIZE(omap3logic_dss_devices),
+ .devices = omap3logic_dss_devices,
+ .default_device = &omap3logic_lcd_device,
+};
+
+static void __init omap3logic_display_init(void)
+{
+ int r;
+
+ r = gpio_request_array(omap3logic_dss_gpios,
+ ARRAY_SIZE(omap3logic_dss_gpios));
+ if (r) {
+ printk(KERN_ERR "failed to get lcd_panel_* gpios\n");
+ return;
+ }
+
+ gpio_export(OMAP3_TORPEDO_LCD_BACKLIGHT_GPIO, 0);
+ gpio_export(OMAP3_TORPEDO_LCD_ENABLE_GPIO, 0);
+ gpio_export(OMAP3_TORPEDO_LCD_PWM_GPIO, 0);
+
+ r = omap_display_init(&omap3logic_dss_data);
+ if (r) {
+ pr_err("OMAP3LOGIC: failed to register DSS device\n");
+ gpio_free_array(omap3logic_dss_gpios,
+ ARRAY_SIZE(omap3logic_dss_gpios));
+ }
+}
+
+static void __init omap3logic_video_mem_init(void)
+{
+ /*
+ * GFX 480x272x32bpp
+ * VID1/2 480x272x32bpp double buffered
+ */
+ omap_vram_set_sdram_vram(PAGE_ALIGN(480 * 272 * 4) +
+ 2 * PAGE_ALIGN(480 * 272 * 4 * 2), 0);
+}
+
+#else
+static void __init omap3logic_display_init(void) { }
+static void __init omap3logic_video_mem_init(void){ }
+#endif /* defined(CONFIG_FB_OMAP2) || defined(CONFIG_FB_OMAP2_MODULE) */
+
+static void __init omap3logic_reserve(void)
+{
+ omap3logic_video_mem_init();
+ omap_reserve();
+}
+
#ifdef CONFIG_OMAP_MUX
static struct omap_board_mux board_mux[] __initdata = {
{ .reg_offset = OMAP_MUX_TERMINATOR },
@@ -197,6 +346,7 @@ static void __init omap3logic_init(void)
omap_sdrc_init(NULL, NULL);
board_mmc_init();
board_smsc911x_init();
+ omap3logic_display_init();
/* Ensure SDRC pins are mux'd for self-refresh */
omap_mux_init_signal("sdrc_cke0", OMAP_PIN_OUTPUT);
@@ -205,6 +355,7 @@ static void __init omap3logic_init(void)
MACHINE_START(OMAP3_TORPEDO, "Logic OMAP3 Torpedo board")
.atag_offset = 0x100,
+ .reserve = omap3logic_reserve,
.map_io = omap3_map_io,
.init_early = omap35xx_init_early,
.init_irq = omap3_init_irq,
--
1.7.0.4
More information about the linux-arm-kernel
mailing list