[PATCH 1/2] ARM: mx5/mx51_babbage: Move GPIO initialization for USB PHY Reset line to commom place

[Uwe Kleine-König]

Hello Fabio,

On Wed, Apr 27, 2011 at 09:44:31PM -0300, Fabio Estevam wrote:
> The USB PHY Reset GPIO can be configured in the same place as the other GPIOs.
> 
> While at it rename the pin as BABBAGE_USB_PHY_RESET to make clearer its purpose.
> 
> Signed-off-by: Fabio Estevam <fabio.estevam at freescale.com>
> ---
>  arch/arm/mach-mx5/board-mx51_babbage.c |   11 ++++++-----
>  1 files changed, 6 insertions(+), 5 deletions(-)
> 
> diff --git a/arch/arm/mach-mx5/board-mx51_babbage.c b/arch/arm/mach-mx5/board-mx51_babbage.c
> index c7b3fab..7b919bc 100644
> --- a/arch/arm/mach-mx5/board-mx51_babbage.c
> +++ b/arch/arm/mach-mx5/board-mx51_babbage.c
> @@ -36,7 +36,7 @@
>  
>  #define BABBAGE_USB_HUB_RESET	IMX_GPIO_NR(1, 7)
>  #define BABBAGE_USBH1_STP	IMX_GPIO_NR(1, 27)
> -#define BABBAGE_PHY_RESET	IMX_GPIO_NR(2, 5)
> +#define BABBAGE_USB_PHY_RESET	IMX_GPIO_NR(2, 5)
>  #define BABBAGE_FEC_PHY_RESET	IMX_GPIO_NR(2, 14)
>  #define BABBAGE_POWER_KEY	IMX_GPIO_NR(2, 21)
>  #define BABBAGE_ECSPI1_CS0	IMX_GPIO_NR(4, 24)
> @@ -110,6 +110,9 @@ static iomux_v3_cfg_t mx51babbage_pads[] = {
>  	/* USB HUB reset line*/
>  	MX51_PAD_GPIO1_7__GPIO1_7,
>  
> +	/* USB PHY reset line */
> +	MX51_PAD_EIM_D21__GPIO2_5,
> +
>  	/* FEC */
>  	MX51_PAD_EIM_EB2__FEC_MDIO,
>  	MX51_PAD_EIM_EB3__FEC_RDATA1,
> @@ -172,7 +175,6 @@ static struct imxi2c_platform_data babbage_hsi2c_data = {
>  static int gpio_usbh1_active(void)
>  {
>  	iomux_v3_cfg_t usbh1stp_gpio = MX51_PAD_USBH1_STP__GPIO1_27;
> -	iomux_v3_cfg_t phyreset_gpio = MX51_PAD_EIM_D21__GPIO2_5;
>  	int ret;
>  
>  	/* Set USBH1_STP to GPIO and toggle it */
> @@ -189,14 +191,13 @@ static int gpio_usbh1_active(void)
>  	gpio_free(BABBAGE_USBH1_STP);
>  
>  	/* De-assert USB PHY RESETB */
> -	mxc_iomux_v3_setup_pad(phyreset_gpio);
> -	ret = gpio_request(BABBAGE_PHY_RESET, "phy_reset");
> +	ret = gpio_request(BABBAGE_USB_PHY_RESET, "phy_reset");
>  
>  	if (ret) {
>  		pr_debug("failed to get MX51_PAD_EIM_D21__GPIO_2_5: %d\n", ret);
>  		return ret;
>  	}
> -	gpio_direction_output(BABBAGE_PHY_RESET, 1);
> +	gpio_direction_output(BABBAGE_USB_PHY_RESET, 1);
>  	return 0;
>  }
this looks like a candidate for gpio_request_one, doesn't it?

Best regards
Uwe

-- 
Pengutronix e.K.                           | Uwe Kleine-König            |
Industrial Linux Solutions                 | http://www.pengutronix.de/  |