[PATCH] ARCH arm: adding new board: CDU
Ryan Mallon
ryan at bluewatersys.com
Mon Apr 4 16:25:53 EDT 2011
On 04/04/2011 09:10 PM, Prchal Jiří wrote:
> Hi,
> this is separated PATCH adding new board CDU.
Please repost as a new email with a proper change log. This patch
shouldn't depend on the CDU audio driver patch. This should still build
and run, just without audio support.
Few more comments below.
~Ryan
<snip>
> diff -uprN -X linux-2.6.38-vanilla/Documentation/dontdiff linux-2.6.38-vanilla/arch/arm/mach-at91/board-cdu.c
> linux-2.6.38-patch/arch/arm/mach-at91/board-cdu.c
> --- linux-2.6.38-vanilla/arch/arm/mach-at91/board-cdu.c 1970-01-01 01:00:00.000000000 +0100
> +++ linux-2.6.38-patch/arch/arm/mach-at91/board-cdu.c 2011-03-28 15:52:03.413048601 +0200
> @@ -0,0 +1,332 @@
> +/*
> + * linux/arch/arm/mach-at91/board-cdu.c
> + *
> + * Copyright (C) 2005 SAN People
> + * Copyright (C) 2006 Atmel
> + * Copyright (C) 2011 AKsignal Brno
> + * jiri.prchal at aksignal.cz
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License as published by
> + * the Free Software Foundation; either version 2 of the License, or
> + * (at your option) any later version.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * You should have received a copy of the GNU General Public License
> + * along with this program; if not, write to the Free Software
> + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
> + */
> +
> +#include <linux/types.h>
> +#include <linux/init.h>
> +#include <linux/mm.h>
> +#include <linux/module.h>
> +#include <linux/platform_device.h>
> +#include <linux/spi/spi.h>
> +#include <linux/clk.h>
> +#include <linux/spi/mcp23s08.h>
> +#include <linux/dma-mapping.h>
> +
> +#include <mach/hardware.h>
> +#include <asm/setup.h>
> +#include <asm/mach-types.h>
> +#include <asm/irq.h>
> +
> +#include <asm/mach/arch.h>
> +#include <asm/mach/map.h>
> +#include <asm/mach/irq.h>
> +
> +#include <mach/board.h>
> +#include <mach/gpio.h>
> +#include <mach/at91sam9_smc.h>
> +
> +#include "sam9_smc.h"
> +#include "generic.h"
> +
> +static void __init cdu_map_io(void)
> +{
> + /* Initialize processor: 6 MHz crystal */
> + at91sam9260_initialize(6000000);
> +
> + /* DBGU on ttyS0. (Rx & Tx only) */
> + at91_register_uart(0, 0, 0);
> +
> + /* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
> + at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
> + | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
> + | ATMEL_UART_RI);
> +
> + /* USART1 on ttyS2. (Rx, Tx, RTS) */
> + at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_RTS);
> +
> + /* USART2 on ttyS3. (Rx, Tx, RTS) */
> + at91_register_uart(AT91SAM9260_ID_US2, 3, ATMEL_UART_RTS);
> +
> + /* USART3 on ttyS4. (Rx, Tx, RTS) */
> + at91_register_uart(AT91SAM9260_ID_US3, 4, ATMEL_UART_RTS);
> +
> + /* USART4 on ttyS5. (Tx) */
> + /* EBUS - transmit audio, no rx */
> + /*at91_register_uart(AT91SAM9260_ID_US4, 5, 0);*/
> +
> + /* set serial console to ttyS0 (ie, DBGU) */
> + at91_set_serial_console(0);
> +}
> +
> +static void __init cdu_init_irq(void)
> +{
> + at91sam9260_init_interrupts(NULL);
> +}
> +
> +/*
> + * USB Host port
> + */
> +static struct at91_usbh_data __initdata cdu_usbh_data = {
> + .ports = 2,
> +};
> +
> +/*
> + * USB Device port
> + */
> +static struct at91_udc_data __initdata cdu_udc_data = {
> + .vbus_pin = AT91_PIN_PC15,
> + .pullup_pin = 0, /* pull-up driven by UDC */
> +};
> +
> +/*
> + * SPI devices.
> + */
> +#define MCP23S08_GPIO_BASE 128
> +
> +static const struct mcp23s08_platform_data mcp23s08_gpio_info = {
> + .chip[0].is_present = true,
> + .chip[0].pullups = 0,
> + .base = MCP23S08_GPIO_BASE,
> +};
> +
> +static struct spi_board_info cdu_spi_devices[] = {
> + { /* ADC LTC2488 */
> + .modalias = "spidev",
> + .chip_select = 0,
> + .max_speed_hz = 1 * 1000 * 1000,
You have max_speed_hz set as (1 * 1000 * 1000) in some cases and 1000000
in others. Please be consistent. Nitpicky: chip_select and bus_num
should go next to each since they are related.
> + .bus_num = 1,
> + },
> + { /* GPIO expander MCP23S08 */
> + .modalias = "mcp23s08",
> + .chip_select = 1,
> + .max_speed_hz = 1000000,
> + .bus_num = 1,
> + .platform_data = &mcp23s08_gpio_info,
> + .mode = SPI_MODE_3,
> + },
> + { /* non volatile memory (F-RAM) FM25VN10 */
> + .modalias = "spidev",
> + .chip_select = 2,
> + .max_speed_hz = 1 * 1000 * 1000,
> + .bus_num = 1,
> + },
> + { /* audiocodec TLV320AIC3106 */
> + .modalias = "tlv320aic3x-codec",
> + .chip_select = 3,
> + .max_speed_hz = 1000000,
> + .bus_num = 1,
> + .mode = SPI_MODE_1,
> + },
> +};
> +
> +/*
> + * MACB Ethernet device
> + */
> +static struct at91_eth_data __initdata cdu_macb_data = {
> + /*.phy_irq_pin = ... not connected */
Delete this line.
> + .is_rmii = 1,
> +};
> +
> +/*
> + * NAND flash
> + */
> +static struct mtd_partition __initdata cdu_nand_partition[] = {
> + {
> + .name = "bootstrap",
> + .offset = 0,
> + .size = SZ_256K,
> + },
> + {
> + .name = "uboot",
> + .offset = MTDPART_OFS_APPEND,
> + .size = SZ_512K,
> + },
> + {
> + .name = "ubootenv",
> + .offset = MTDPART_OFS_APPEND,
> + .size = SZ_256K,
> + },
> + {
> + .name = "kernel",
> + .offset = MTDPART_OFS_APPEND,
> + .size = SZ_4M,
> + },
> + {
> + .name = "rootfs",
> + .offset = MTDPART_OFS_APPEND,
> + .size = MTDPART_SIZ_FULL,
> + },
> +};
> +
> +static struct mtd_partition * __init nand_partitions(int size, int *num_partitions)
> +{
> + *num_partitions = ARRAY_SIZE(cdu_nand_partition);
> + return cdu_nand_partition;
> +}
> +
> +static struct atmel_nand_data __initdata cdu_nand_data = {
> + .ale = 21,
> + .cle = 22,
> + /*.det_pin = ... not connected */
Just delete this line.
> + .rdy_pin = AT91_PIN_PC13,
> + .enable_pin = AT91_PIN_PC14,
> + .partition_info = nand_partitions,
> + .bus_width_16 = 0,
> +};
> +
> +static struct sam9_smc_config __initdata cdu_nand_smc_config = {
> + .ncs_read_setup = 0,
> + .nrd_setup = 1,
> + .ncs_write_setup = 0,
> + .nwe_setup = 1,
> +
> + .ncs_read_pulse = 3,
> + .nrd_pulse = 3,
> + .ncs_write_pulse = 3,
> + .nwe_pulse = 3,
> +
> + .read_cycle = 5,
> + .write_cycle = 5,
> +
> + .mode = AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE,
Split this line since it runs over 80 columns (especially once you add |
AT91_SMC_DBW_8).
> + .tdf_cycles = 2,
> +};
> +
> +static void __init cdu_add_device_nand(void)
> +{
> + /* setup bus-width 8 */
> + cdu_nand_smc_config.mode |= AT91_SMC_DBW_8;
Move this up into the initialisation above.
> +
> + /* configure chip-select 3 (NAND) */
> + sam9_smc_configure(3, &cdu_nand_smc_config);
> +
> + at91_add_device_nand(&cdu_nand_data);
> +}
> +
> +/*
> +* MCI (SD/MMC)
> +*/
> +static struct at91_mmc_data __initdata ek_mmc_data = {
> + .slot_b = 0,
> + .wire4 = 1,
> + /*.det_pin = ... not connected */
> + /*.wp_pin = ... not connected */
> + /*.vcc_pin = ... not connected */
Delete these lines.
> +};
> +
> +/*
> + * LEDs
> + */
> +static struct gpio_led cdu_leds[] = {
> + {
> + .name = "red",
> + .gpio = AT91_PIN_PC10,
> + .default_trigger = "timer",
> + },
> + {
> + .name = "green",
> + .gpio = AT91_PIN_PA5,
> + .default_trigger = "heartbeat",
> + },
> + {
> + .name = "yellow",
> + .gpio = AT91_PIN_PB20,
> + .active_low = 1,
> + .default_trigger = "mmc0",
> + },
> + {
> + .name = "blue",
> + .gpio = AT91_PIN_PB21,
> + .active_low = 1,
> + .default_trigger = "nand-disk",
> + },
> +};
> +
> +/*
> + * GPIOs
> + */
> +static struct gpio gpios[] = {
> + { AT91_PIN_PA0, GPIOF_OUT_INIT_LOW, "ebus_dir"},
> + { AT91_PIN_PA1, GPIOF_OUT_INIT_LOW, "time_dir"},
> + { AT91_PIN_PB12, GPIOF_OUT_INIT_LOW, "gsm_rst"},
> + { AT91_PIN_PB13, GPIOF_OUT_INIT_LOW, "gsm_on"},
> + { AT91_PIN_PC2, GPIOF_IN, "por"},
> + { AT91_PIN_PC7, GPIOF_OUT_INIT_HIGH, "spk_shdn"},
> +
> + { AT91_PIN_PC0, GPIOF_IN, "in13"},
> + { AT91_PIN_PC1, GPIOF_IN, "in14"},
> + { AT91_PIN_PA22, GPIOF_IN, "in17"},
> + { AT91_PIN_PA23, GPIOF_IN, "in18"},
> + { AT91_PIN_PA24, GPIOF_IN, "in19"},
> + { AT91_PIN_PA25, GPIOF_IN, "in20"},
> +
> + { AT91_PIN_PA26, GPIOF_OUT_INIT_LOW, "out15"},
> + { AT91_PIN_PA27, GPIOF_OUT_INIT_LOW, "out16"},
> + { AT91_PIN_PA28, GPIOF_OUT_INIT_LOW, "out17"},
> + { AT91_PIN_PA29, GPIOF_OUT_INIT_LOW, "out18"},
> + { AT91_PIN_PA30, GPIOF_OUT_INIT_LOW, "out19"},
> + { AT91_PIN_PB29, GPIOF_OUT_INIT_LOW, "out20"},
> +
> + { MCP23S08_GPIO_BASE + 0, GPIOF_IN, "busadrp"},
> + { MCP23S08_GPIO_BASE + 2, GPIOF_IN, "busadr5"},
> + { MCP23S08_GPIO_BASE + 3, GPIOF_IN, "busadr4"},
> + { MCP23S08_GPIO_BASE + 4, GPIOF_IN, "busadr3"},
> + { MCP23S08_GPIO_BASE + 5, GPIOF_IN, "busadr2"},
> + { MCP23S08_GPIO_BASE + 6, GPIOF_IN, "busadr1"},
> + { MCP23S08_GPIO_BASE + 7, GPIOF_IN, "busadr0"},
> +};
> +
> +static void __init cdu_add_gpio(void)
> +{
gpio_request_array(gpios, ARRAY_SIZE(gpios));
> + int i;
> +
> + for (i = 0; i < ARRAY_SIZE(gpios); i++) {
> + gpio_request_one(gpios[i].gpio, gpios[i].flags, gpios[i].label);
> + gpio_export_name(gpios[i].gpio, 0, gpios[i].label);
What does this function do? I can't find it anywhere.
> + }
> +}
> +
> +/*
> + * init
> + */
> +static void __init cdu_board_init(void)
> +{
> + at91_add_device_serial();
> + at91_add_device_usbh(&cdu_usbh_data);
> + at91_add_device_udc(&cdu_udc_data);
> + at91_add_device_spi(cdu_spi_devices, ARRAY_SIZE(cdu_spi_devices));
> + cdu_add_device_nand();
> + at91_add_device_eth(&cdu_macb_data);
> + at91_add_device_mmc(0, &ek_mmc_data);
> + at91_add_device_ssc(AT91SAM9260_ID_SSC, (ATMEL_SSC_TF | ATMEL_SSC_TK | ATMEL_SSC_TD | ATMEL_SSC_RD));
> + at91_gpio_leds(cdu_leds, ARRAY_SIZE(cdu_leds));
> + cdu_add_gpio ();
No space between gpio and ().
> +}
> +
> +MACHINE_START(AT91SAM9260EK, "CDU")
> + /* Maintainer: AKsignal Brno */
Website/email contact?
> + .boot_params = AT91_SDRAM_BASE + 0x100,
> + .timer = &at91sam926x_timer,
> + .map_io = cdu_map_io,
> + .init_irq = cdu_init_irq,
> + .init_machine = cdu_board_init,
> +MACHINE_END
> diff -uprN -X linux-2.6.38-vanilla/Documentation/dontdiff linux-2.6.38-vanilla/arch/arm/mach-at91/Kconfig
> linux-2.6.38-patch/arch/arm/mach-at91/Kconfig
> --- linux-2.6.38-vanilla/arch/arm/mach-at91/Kconfig 2011-03-15 02:20:32.000000000 +0100
> +++ linux-2.6.38-patch/arch/arm/mach-at91/Kconfig 2011-03-16 09:19:40.000000000 +0100
> @@ -213,6 +213,12 @@ config MACH_AT91SAM9260EK
> Select this if you are using Atmel's AT91SAM9260-EK or AT91SAM9XE Evaluation Kit
> <http://www.atmel.com/dyn/products/tools_card.asp?tool_id=3933>
>
> +config MACH_CDU
> + bool "CDU AKsignal board"
> + help
> + Select this if you are using AKsignal CDU board
> + <http://www.aksignal.cz>
> +
> config MACH_CAM60
> bool "KwikByte KB9260 (CAM60) board"
> help
> diff -uprN -X linux-2.6.38-vanilla/Documentation/dontdiff linux-2.6.38-vanilla/arch/arm/mach-at91/Makefile
> linux-2.6.38-patch/arch/arm/mach-at91/Makefile
> --- linux-2.6.38-vanilla/arch/arm/mach-at91/Makefile 2011-03-15 02:20:32.000000000 +0100
> +++ linux-2.6.38-patch/arch/arm/mach-at91/Makefile 2011-03-16 09:19:40.000000000 +0100
> @@ -40,6 +40,7 @@ obj-$(CONFIG_MACH_ECO920) += board-eco92
>
> # AT91SAM9260 board-specific support
> obj-$(CONFIG_MACH_AT91SAM9260EK) += board-sam9260ek.o
> +obj-$(CONFIG_MACH_CDU) += board-cdu.o
> obj-$(CONFIG_MACH_CAM60) += board-cam60.o
> obj-$(CONFIG_MACH_SAM9_L9260) += board-sam9-l9260.o
> obj-$(CONFIG_MACH_USB_A9260) += board-usb-a9260.o
> diff -uprN -X linux-2.6.38-vanilla/Documentation/dontdiff linux-2.6.38-vanilla/MAINTAINERS linux-2.6.38-patch/MAINTAINERS
> --- linux-2.6.38-vanilla/MAINTAINERS 2011-03-15 02:20:32.000000000 +0100
> +++ linux-2.6.38-patch/MAINTAINERS 2011-03-25 08:37:56.693049978 +0100
> @@ -1640,6 +1640,13 @@ F: include/linux/can/error.h
> F: include/linux/can/netlink.h
> F: include/linux/can/platform/
>
> +CDU BOARD
> +M: Jiri Prchal <jiri.prchal at aksignal.cz>
> +L: linux-arch at vger.kernel.org
> +W: http://www.linux4sam.org
> +S: Supported
> +F: arch/arm/mach-at91/
> +
> CELL BROADBAND ENGINE ARCHITECTURE
> M: Arnd Bergmann <arnd at arndb.de>
> L: linuxppc-dev at lists.ozlabs.org
> Soubory linux-2.6.38-vanilla/scripts/recordmcount a linux-2.6.38-patch/scripts/recordmcount jsou rĹŻznĂŠ
--
Bluewater Systems Ltd - ARM Technology Solution Centre
Ryan Mallon 5 Amuri Park, 404 Barbadoes St
ryan at bluewatersys.com PO Box 13 889, Christchurch 8013
http://www.bluewatersys.com New Zealand
Phone: +64 3 3779127 Freecall: Australia 1800 148 751
Fax: +64 3 3779135 USA 1800 261 2934
More information about the linux-arm-kernel
mailing list