[PATCH 1/2] ARM: S5PV210: Add audio support to Aquila

Kukjin Kim kgene.kim at samsung.com
Wed Sep 29 08:16:36 EDT 2010


Chanwoo Choi wrote:
> 
> Mark Brown wrote:
> > On Wed, Jul 28, 2010 at 12:04:44PM +0900, Chanwoo Choi wrote:
> >
> >> +static struct regulator_consumer_supply wm8994_fixed_voltage0_supplies[] =
> {
> >> +	{
> >> +		.dev_name	= "5-001a",
> >> +		.supply		= "DBVDD",
> >> +	}, {
> >> +		.dev_name	= "5-001a",
> >> +		.supply		= "AVDD2",
> >> +	}, {
> >> +		.dev_name	= "5-001a",
> >> +		.supply		= "CPVDD",
> >> +	},
> >> +
> >> +};
> >> +
> >> +static struct regulator_consumer_supply wm8994_fixed_voltage1_supplies[] =
> {
> >
> > All these fixed voltage regulators seem a bit suspicous for a mobile
> > phone - I'd have expected that the supplies would all be being provided
> > by your PMIC except for things taken directly from the battery supply
> > (like the speakers tend to be, for example)?  There's no problem with
> > the code itself, it just looks a bit odd.
> >
> 
> All these consumer supply of WM8994 codec connected the below
> regulator(VCC_1.8V) on
> a circuit diagram. "VCC_1.8V" regualtor is always enabled, because it is used to
> many devices.
> Then I haven't connected all these consumer supply of WM8994 codec to
> "VCC_1.8V" regulator.
> I will modify that the consumer supply would be provided by PMIC.
> 
> static struct regulator_init_data aquila_buck3_data = {
> 	.constraints	= {
> 		.name		= "VCC_1.8V",
> 		.min_uV		= 1800000,
> 		.max_uV		= 1800000,
> 		.apply_uV	= 1,
> 		.state_mem	= {
> 			.enabled = 1,
> 		},
> 	},
> };
> 
> >> +static struct i2c_board_info i2c_gpio5_devs[] __initdata = {
> >> +	{
> >> +		/* CS/ADDR = low 0x34 (FYI: high = 0x36) */
> >> +		I2C_BOARD_INFO("wm8994", 0x34 >> 1),
> >> +		.platform_data	= &wm8994_platform_data,
> >> +	},
> >> +};
> >
> > Probably clearer for generic Linux use to specify the address as 0x1a
> > directly.
> 
> Ok, I will do.
> 
> >
> >> +static void __init aquila_sound_init(void)
> >> +{
> >> +	unsigned int gpio;
> >> +
> >> +	/* CODEC_XTAL_EN */
> >> +	gpio = S5PV210_GPH3(2);		/* XEINT_26 */
> >> +	gpio_request(gpio, "CODEC_XTAL_EN");
> >> +	s3c_gpio_cfgpin(gpio, S3C_GPIO_OUTPUT);
> >> +	s3c_gpio_setpull(gpio, S3C_GPIO_PULL_NONE);
> >> +	gpio_direction_output(gpio, 1);
> >
> > Might be as well to provide some or all this stuff in your audio machine
> > driver?
> 
> The Aquila board have a oscillator which provide main clock to
> WM8994 audio codec. The oscillator provide 24MHz clock to WM8994 audio codec
> (MCLK1 pin). I set gpio setting of "CODEC_XTAL_EN" to enable a oscillator.
> 
> >
> >> +	/* MICBIAS_EN */
> >> +	gpio = S5PV210_GPJ4(2);			/* XMSMRN */
> >> +	gpio_request(gpio, "MICBIAS_EN");
> >> +	s3c_gpio_cfgpin(gpio, S3C_GPIO_OUTPUT);
> >> +	gpio_direction_output(gpio, 1);
> >
> > This in particular would benefit from keeping the request of the GPIO
> > joined up with the driver that uses it.
> 
> Ok, I will move this code to machine driver(sound/soc/s3c24xxx/aquila_wm8994.c).
> 
> >> +	/* ADC_EN */
> >> +	gpio = S5PV210_GPJ3(2);
> >> +	gpio_request(gpio, "ADC_EN");
> >> +	s3c_gpio_cfgpin(gpio, S3C_GPIO_OUTPUT);
> >> +	gpio_direction_output(gpio, 1);
> >
> > I'm not sure what this does?
> >
> 
> I explained below description about "ADC_EN" :
> "ADC_EN : This gpio enable the ADC device which is used to detect
>  the kind of jack. (SND_JACK_HEADPHONE/HEADSET/MECHANICAL/AVOUT)
>  According to the kind of jack, an electric current is changed.
>  (Only used on Aquila board) "
> 
> When inserting the jack to Aquila board, I used ADC driver so that, detecting
> the kind of jack(SND_JACK_HEADPHONE/HEADSET/MECHANICAL/AVOUT).
> 
> I will separately make the another function to initialize ADC driver.
> 
> Thank you for your comment.
> Chanwoo Choi
> 
Hi,

How was going on?

Thanks.

Best regards,
Kgene.
--
Kukjin Kim <kgene.kim at samsung.com>, Senior Engineer,
SW Solution Development Team, Samsung Electronics Co., Ltd.




More information about the linux-arm-kernel mailing list