linux-2.6.36-rc4 problems booting rootfs from SD card
dylan cristiani
d.cristiani at idem-tech.it
Tue Sep 28 10:51:26 EDT 2010
On Tue, 28 Sep 2010 17:16:41 +0300
Vasily Khoruzhick <anarsoul at gmail.com> wrote:
> On 28 of September 2010 14:00:43 dylan cristiani wrote:
> > Hi sirs, here is my scenario: kernel 2.6.36-rc4; cpu pxa270;
> > platform is an enhancement (i like to see things that way...) and
> > customisation of the mainstone III board; here comes the (my)
> > problem: if i boot with my standard kernel boot command line (to
> > boot from system flash): 'root=/dev/mtdblock2 rootfstype=jffs2
> > mem=64M console=ttyS0,115200n8'
> >
> > i can get the rootfs up, and the SD card is up too, and correctly
> > working; here's the relevant kernel log:
> >
> > ....
> > XScale iWMMXt coprocessor detected.
> > rtc-ds1307 0-0068: setting system clock to 2010-09-28 03:03:08 UTC
> > (1285642988)
> > pxa27x-udc pxa27x-udc: USB reset
> > mmc0: new SD card at address aaaa
> > mmcblk0: mmc0:aaaa SD02G 1.84 GiB
> > mmcblk0: p1
> > pxa27x-udc pxa27x-udc: USB reset
> > .....
> >
> > then the rootfs coems up properly.
> >
> > Else, if i try to boot the rootfs directly form the SD card, with
> > kernel boot command line:
> > 'root=/dev/mmcblk0p1 rootfstype=ext2 mem=64M console=ttyS0,115200n8'
> >
> > the rootfs doen't work, and i can see some problems around with usb
> > client gadget; here's the relevant kernel log:
> >
> > ....
> > XScale iWMMXt coprocessor detected.
> > rtc-ds1307 0-0068: setting system clock to 2010-09-28 03:03:43 UTC
> > (1285643023)
> > VFS: Cannot open root device "mmcblk0p1" or unknown-block(0,0)
> > Please append a correct "root=" boot option; here are the available
> > partitions:
> > 1f00 256 mtdblock0 (driver?)
> > 1f01 2048 mtdblock1 (driver?)
> > 1f02 63232 mtdblock2 (driver?)
> > Kernel panic - not syncing: VFS: Unable to mount root fs on
> > unknown-block(0,0)
> > Backtrace:
> > [] (dump_backtrace+0x0/0x118) from [] (dump_stack+0x18/0x1c)
> > r6:00008000 r5:c3813000 r4:c0417b70 r3:c03f5714
> > [] (dump_stack+0x0/0x1c) from [] (panic+0x60/0x18c)
> > [] (panic+0x0/0x18c) from [] (mount_block_root+0x25c/0x2ac)
> > pxa27x-udc pxa27x-udc: ep0:handle_ep0: state=WAIT_FOR_SETUP,
> > req=(null), udccsr0=0x2c1, udcbcr=8, irq_msk=1
> > pxa27x-udc pxa27x-udc: ep0:set_ep0state:
> > state=WAIT_FOR_SETUP->SETUP_STAGE, udccsr0=0x2c1, udcbcr=8
> > pxa27x-udc pxa27x-udc: ep0:handle_ep0_ctrl_req: SETUP 80.06 v0100
> > i0000 l0040
> > pxa27x-udc pxa27x-udc: ep0:set_ep0state:
> > state=SETUP_STAGE->IN_DATA_STAGE, udccsr0=0x281, udcbcr=0
> > pxa27x-udc pxa27x-udc: ep0:pxa_ep_queue: queue req
> > c393dbc0(first=yes), len 18 buf c386d000
> > pxa27x-udc pxa27x-udc: ep0:write_ep0_fifo: in 16 bytes, 2 left,
> > req=c393dbc0, udccsr0=0x202
> > pxa27x-udc pxa27x-udc: USB reset
> > pxa27x-udc pxa27x-udc: USB reset start
> > pxa27x-udc pxa27x-udc: ep0:req_done: complete req c393dbc0 stat -71
> > len 16/18
> > g_ether gadget: setup complete --> -71, 16/18
> > pxa27x-udc pxa27x-udc: ep0:set_ep0state:
> > state=IN_DATA_STAGE->WAIT_FOR_SETUP, udccsr0=0x200, udcbcr=0
> > pxa27x-udc pxa27x-udc: ep0:handle_ep0: state=WAIT_FOR_SETUP,
> > req=(null), udccsr0=0x200, udcbcr=0, irq_msk=1
> > r3:00000001 r2:20000013 r1:c3825f60 r0:c039601b
> > [] (mount_block_root+0x0/0x2ac) from [] (mount_root+0x54/0x6c)
> > r8:00000000 r7:00000013 r6:c0051e48 r5:00000000 r4:c039607f
> > [] (mount_root+0x0/0x6c) from [] (prepare_namespace+0x12c/0x184)
> > r5:c00203c1 r4:c00203ac
> > [] (prepare_namespace+0x0/0x184) from [] (kernel_init+0x114/0x154)
> > r5:c00083d4 r4:c0416e60
> > [] (kernel_init+0x0/0x154) from [] (do_exit+0x0/0x5dc)
> > r4:00000000 r3:00000000
> > ....
> >
> > last months i ported my system form ancient 2.6.18 kernel to my
> > current kernel (2.6.36-rc4), but i remember that with 2.6.18 the
> > rootfs's booting from SD did work; so i re-loaded 2.6.18 zImage,
> > and in fact the SD roots booting worked properly; then i
> > investigated a bit and i have found that also with 2.6.19 it
> > worked, while with 2.6.20 it stopped working (i didn't try between
> > 2.6.20 and 2.6.36-rc4 but if it's helpful i can do it).
> > The only way to solve my problem was to 'patch' the file
> > drivers/Makefile, moving the mmc.o object file upward; here is a
> > sort of 'patch', but i regret in advance for some 'possible' (i had
> > to write 'sure', but i like to be modest person....) syntax
> > mistake, but i'm not in habbit with patches...:
> >
> > --- a/drivers/Makefile
> > +++ b/drivers/Makefile
> > @@ -44,7 +44,8 @@
> > obj-y += macintosh/
> > obj-$(CONFIG_IDE) += ide/
> > obj-$(CONFIG_SCSI) += scsi/
> > obj-$(CONFIG_ATA) += ata/
> > obj-$(CONFIG_MTD) += mtd/
> > obj-$(CONFIG_SPI) += spi/
> > +obj-$(CONFIG_MMC) += mmc/
> > obj-y += net/
> > @@ -92,9 +93,8 @@
> > obj-y += lguest/
> > obj-$(CONFIG_CPU_FREQ) += cpufreq/
> > obj-$(CONFIG_CPU_IDLE) += cpuidle/
> > -obj-$(CONFIG_MMC) += mmc/
> > obj-$(CONFIG_MEMSTICK) += memstick/
> > obj-$(CONFIG_NEW_LEDS) += leds/
> > obj-$(CONFIG_INFINIBAND) += infiniband/
> > obj-$(CONFIG_SGI_SN) += sn/
> > obj-y += firmware/
> >
> > stated that it's not clear to me why when i don't try to boot the
> > rootfs directly from the SD, its driver comes up in the right way,
> > and the SD works, while when i try to boot the rootfs from the SD i
> > cannot get things to work (maybe the device is not up yet when the
> > VFS tryies to come up in fact in such a situation i cannot read any
> > log about mmc0 device!), i was wondering if this patch could be
> > fair or maybe (probably) i'm missing some potential side effects???
> > any hint will be appreciated!!!
> > thanks and bye
> >
> > -
> >
> > dylan cristiani
> >
> > --
> > Fortunately I’ve been adhering to a pretty strict, uh, drug regimen
> > to keep my mind, you know, uh, limber...
> > ---
>
> It seems you're missing rootdelay=[0-9]+ argument to kernel
you scored a great gol Vasily, simply adding
rootdealy=1
to my boot command line solved the issue!!!
thanks a million and uhm....i wasn't missing it, it was just a question
of infinite ignorance of mine....sorry for noise!!!
dylan
More information about the linux-arm-kernel
mailing list