[PATCH] mmc: failure of block read wait for long time

[Adrian Hunter]

On 20/09/10 11:57, Ghorai, Sukumar wrote:
> Adrian,
>
>> -----Original Message-----
>> From: Adrian Hunter [mailto:adrian.hunter at nokia.com]
>> Sent: Monday, September 20, 2010 1:24 PM
>> To: Ghorai, Sukumar
>> Cc: linux-mmc at vger.kernel.org; linux-arm-kernel at lists.infradead.org;
>> Adrian Hunter
>> Subject: Re: [PATCH] mmc: failure of block read wait for long time
>>
>> On 14/09/10 08:15, ext Ghorai, Sukumar wrote:
>>> Adrian,
>>>
>>> [..snip..]
>>>>>>> [Ghorai] Adrian,
>>>>>>> Yes this works and reduced the retry by 1/4 (2048 to 512 times for
>> 1MB
>>>>>> data read) form the original code;
>>>>>>> Initially it was retrying for each page(512 bytes) after multi-block
>>>>>> read fail; but this solution is retying for each segment(2048 bytes);
>>>>>>> 1. Now say block layrer reading 1MB and failed for the 1st segment.
>> So
>>>>>> it will still retry for 1MB/2048-bytes, i.e. 512 times.
>>>>>>> 2. So do you think any good reason to retry again and again?
>>>>>> If you have 1MB that is not readable, it sounds like the card is
>> broken.
>>>>>> Why are so many reads failing?  Has the card been removed?
>>>>>>
>>>>>> You might very rarely see ECC errors in a small number of sectors,
>>>>>> but more than that sounds like something else is broken.
>>>>>
>>>>> [Ghorai] yes, one example is we remove the card when reading data,
>>>>
>>>> Well, that is a different case.  Once the card has gone, the block
>> driver
>>>> can (and will once the remove method is called) error out all I/O
>>>> requests without sending them to MMC.  That doesn't happen until there
>>>> is a card detect interrupt and a resulting rescan.
>>>
>>> [Ghorai] here we are discussing two problem,
>>> 1. If IO failed how to stop retry; because of -
>>> 	a. internal card error
>>> 	b. issue in Filesystem, driver, or host controller issue
>>> 	c. or cards removed.
>>>
>>> 2. And 2nd how to sync block-layer IO, if card removed,
>>> 	a. case 1: when card removed interrupt support by the platform
>>> 	b. case 2: when card removed interrupt does not support by the
>> platform?
>>>
>>>>
>>>> A possible solution is to put a flag on mmc_card to indicate card_gone
>>>> that gets set as soon as the drivers card detect interrupt shows there
>>>> is no card (hoping that we are not getting any bouncing on card detect)
>>>> and then have mmc_wait_for_req() simple return -ENODEV immediately if
>>>> the card_gone flag is set.  Finally, if the mmc block driver sees
>>>> a -ENODEV error, it should also check the card_gone flag (via a new
>>>> core function) and if the card is gone, do not retry - and perhaps
>>>> even error out the rest of the I/O request queue as well.
>>>
>>> [Ghorai] your idea address the 2.a case, but not 2.b, 1.a, 1.b
>>
>> The card removal case can be extended to use the bus ops detect method
>> when there is no card detect irq.  I will send a RFC patch.
>>
>> With respect to 1.a:
>>    - If the card has an internal error, then it is broken.  The user
>>    should remove the card and use a better one.  I do not see how reducing
>>    retry delays really helps the user very much.  Arguably if the card
>>    becomes unresponsive, the MMC core could provide a facility to
>>    reinitialise the card, but that is yet another issue.
>>
>> With respect to 1.b:
>>    - The file system cannot cause the block driver to have I/O errors.
>>    - If there are errors in the driver they should be fixed.
>>    - If there are hardware problems with the host controller, then
>>    it is up to the host controller driver to deal with them e.g.
>>    by resetting the controller.  I don't see what this has to do with
>>    the block driver.
>>
>> You leave out the important case of ECC errors.  I am concerned about
>> this because of the possibility that it happens inside a file system
>> journal e.g. EXT4 journal.  Perhaps the journal may be recovered if the
>> error only affects the last transaction, but perhaps not if it destroys
>> other transactions - which could happen if the approach you suggest
>> is taken.
>>
> [Ghorai] Thanks lot for your descriptive answer.
> 1. Can you answer this? 2.b. case 2: when card removed interrupt does not support by the platform?

As I wrote above: The card removal case can be extended to use the bus ops
detect method when there is no card detect irq.  I will send a RFC patch.

>
> 2. Why block layer handling for inter-leave data? Can you give example diver who is returning interleave data? And how to tell application that buffer having interleave data?

I am not sure what you mean by interleave data, but file systems  for example
are free to map any block to any file, directory or file system object,
so a consecutive series of sectors may contain unrelated data.  Up to a maximum
size, the block layer merges I/O requests when the sectors are consecutive,
so an I/O request can also contain unrelated data.

>
>>>
>>> And the solution I was proposing to return the status of IO failure as
>> soon as possible to above layer; and handle the card removed interrupt
>> separately or any other issue in h/w or s/w or combination of both. Or
>> just think again when platform don't have the card remove interrupt.
>>>
>>> So my patch addresses the 1st part
>>
>> It is absolutely unacceptable to return I/O errors to the upper layers
>> for segments that do not have errors.
>>
>>> And for the 2nd part we can submit the patch anytime.
>>>
>>>>
>>>> I can suggest a patch if you want but I am on vacation next week so
>>>> it will have to wait a couple of weeks.
>>>>
>>>>> And moreover we should not give the interleave data to apps, as we
>> don't
>>>> have option to tell application for the valid data.
>>>>>
>>> [..snip..]
>>> http://comments.gmane.org/gmane.linux.kernel.mmc/2714
>>>
>>>>>
>>>
>>>
>
> --
> To unsubscribe from this list: send the line "unsubscribe linux-mmc" in
> the body of a message to majordomo at vger.kernel.org
> More majordomo info at  http://vger.kernel.org/majordomo-info.html
>