[PATCH RESEND v4 4/4] omap: nand: making ecc layout as compatible with romcode ecc
Sukumar Ghorai
s-ghorai at ti.com
Thu Sep 16 04:00:59 EDT 2010
This patch overrides nand ecc layout and bad block descriptor (for 8-bit
device) to support hw ecc in romcode layout. So as to have in sync with ecc
layout throughout; i.e. x-loader, u-boot and kernel.
This patch also enables to use romcode ecc for spd and zoom, by default.
This enables to flash x-loader, u-boot, kernel, FS images from kernel itself
and compatiable with other tools.
Signed-off-by: Sukumar Ghorai <s-ghorai at ti.com>
Signed-off-by: Vimal Singh <vimalsingh at ti.com>
---
arch/arm/mach-omap2/board-flash.c | 2 +-
drivers/mtd/nand/omap2.c | 34 ++++++++++++++++++++++++++++++++++
2 files changed, 35 insertions(+), 1 deletions(-)
diff --git a/arch/arm/mach-omap2/board-flash.c b/arch/arm/mach-omap2/board-flash.c
index 5f74c8f..d71c511 100644
--- a/arch/arm/mach-omap2/board-flash.c
+++ b/arch/arm/mach-omap2/board-flash.c
@@ -145,7 +145,7 @@ __init board_nand_init(struct mtd_partition *nand_parts, u8 nr_parts, u8 cs)
board_nand_data.cs = cs;
board_nand_data.parts = nand_parts;
board_nand_data.nr_parts = nr_parts;
- board_nand_data.ecc_opt = OMAP_ECC_HAMMING_CODE_DIFF_LAYOUT;
+ board_nand_data.ecc_opt = OMAP_ECC_HAMMING_CODE_HW;
gpmc_nand_init(&board_nand_data);
}
diff --git a/drivers/mtd/nand/omap2.c b/drivers/mtd/nand/omap2.c
index dbbd699..33c356b 100644
--- a/drivers/mtd/nand/omap2.c
+++ b/drivers/mtd/nand/omap2.c
@@ -128,6 +128,20 @@ const int use_dma;
const int use_interrupt;
#endif
+/* oob info generated runtime depending on ecc algorithm and layout selected */
+static struct nand_ecclayout omap_oobinfo;
+/* Define some generic bad / good block scan pattern which are used
+ * while scanning a device for factory marked good / bad blocks
+ */
+static uint8_t scan_ff_pattern[] = { 0xff };
+static struct nand_bbt_descr bb_descrip_flashbased = {
+ .options = NAND_BBT_SCANEMPTY | NAND_BBT_SCANALLPAGES,
+ .offs = 0,
+ .len = 1,
+ .pattern = scan_ff_pattern,
+};
+
+
struct omap_nand_info {
struct nand_hw_control controller;
struct omap_nand_platform_data *pdata;
@@ -945,6 +959,7 @@ static int __devinit omap_nand_probe(struct platform_device *pdev)
struct omap_nand_info *info;
struct omap_nand_platform_data *pdata;
int err;
+ int i, offset;
pdata = pdev->dev.platform_data;
if (pdata == NULL) {
@@ -1079,6 +1094,25 @@ static int __devinit omap_nand_probe(struct platform_device *pdev)
}
}
+ /* rom code layout */
+ if (pdata->ecc_opt != OMAP_ECC_HAMMING_CODE_DIFF_LAYOUT) {
+ offset = (info->nand.options & NAND_BUSWIDTH_16) ? 2 : 1;
+ if (info->mtd.oobsize == 16) {
+ info->nand.badblock_pattern = &bb_descrip_flashbased;
+ omap_oobinfo.eccbytes = 3;
+ } else
+ omap_oobinfo.eccbytes = 3 * 4;
+
+ for (i = 0; i < omap_oobinfo.eccbytes; i++)
+ omap_oobinfo.eccpos[i] = i+offset;
+
+ omap_oobinfo.oobfree->offset = offset + omap_oobinfo.eccbytes;
+ omap_oobinfo.oobfree->length = info->mtd.oobsize -
+ (offset + omap_oobinfo.eccbytes);
+
+ info->nand.ecc.layout = &omap_oobinfo;
+ }
+
#ifdef CONFIG_MTD_PARTITIONS
err = parse_mtd_partitions(&info->mtd, part_probes, &info->parts, 0);
if (err > 0)
--
1.7.0.4
More information about the linux-arm-kernel
mailing list