[PATCH 7/9] esdhc-3 mx51: Modify the MSL codes when upstreaming fsl esdhc driver
Richard Zhu
r65037 at freescale.com
Wed Sep 1 05:48:38 EDT 2010
Modify the MSL codes and add the eSDHC1 and eSDHC2 support
on MX51 BBG platform.
IOMUX, CLOCK, register the device.
Signed-off-by: Richard Zhu <r65037 at freescale.com>
---
arch/arm/mach-mx5/board-mx51_babbage.c | 70 +++++++++++
arch/arm/mach-mx5/clock-mx51.c | 197 ++++++++++++++++++++++++++++++++
arch/arm/mach-mx5/devices.c | 52 +++++++++
arch/arm/mach-mx5/devices.h | 2 +
4 files changed, 321 insertions(+), 0 deletions(-)
diff --git a/arch/arm/mach-mx5/board-mx51_babbage.c b/arch/arm/mach-mx5/board-mx51_babbage.c
index 6e384d9..57873fb 100644
--- a/arch/arm/mach-mx5/board-mx51_babbage.c
+++ b/arch/arm/mach-mx5/board-mx51_babbage.c
@@ -24,6 +24,7 @@
#include <mach/iomux-mx51.h>
#include <mach/i2c.h>
#include <mach/mxc_ehci.h>
+#include <mach/mmc.h>
#include <asm/irq.h>
#include <asm/setup.h>
@@ -33,6 +34,8 @@
#include "devices.h"
+#define BABBAGE_SDHCI1_WP (0*32 + 1) /* GPIO_1_1 */
+#define BABBAGE_SDHCI2_WP (0*32 + 5) /* GPIO_1_5 */
#define BABBAGE_USB_HUB_RESET (0*32 + 7) /* GPIO_1_7 */
#define BABBAGE_USBH1_STP (0*32 + 27) /* GPIO_1_27 */
#define BABBAGE_PHY_RESET (1*32 +5) /* GPIO_2_5 */
@@ -93,6 +96,24 @@ static struct pad_desc mx51babbage_pads[] = {
/* USB HUB reset line*/
MX51_PAD_GPIO_1_7__GPIO_1_7,
+
+ /* SDHCI1 IOMUX */
+ MX51_PAD_SD1_CMD__SD1_CMD,
+ MX51_PAD_SD1_CLK__SD1_CLK,
+ MX51_PAD_SD1_DATA0__SD1_DATA0,
+ MX51_PAD_SD1_DATA1__SD1_DATA1,
+ MX51_PAD_SD1_DATA2__SD1_DATA2,
+ MX51_PAD_SD1_DATA3__SD1_DATA3,
+ MX51_PAD_GPIO_1_0__GPIO_1_0,
+
+ /* SDHCI2 IOMUX */
+ MX51_PAD_SD2_CMD__SD2_CMD,
+ MX51_PAD_SD2_CLK__SD2_CLK,
+ MX51_PAD_SD2_DATA0__SD2_DATA0,
+ MX51_PAD_SD2_DATA1__SD2_DATA1,
+ MX51_PAD_SD2_DATA2__SD2_DATA2,
+ MX51_PAD_SD2_DATA3__SD2_DATA3,
+ MX51_PAD_GPIO_1_5__GPIO_1_5,
};
/* Serial ports */
@@ -240,6 +261,53 @@ static int __init babbage_otg_mode(char *options)
}
__setup("otg_mode=", babbage_otg_mode);
+static int sdhc_write_protect(struct device *dev)
+{
+ struct pad_desc sdhci1wp_gpio = MX51_PAD_GPIO_1_1__GPIO_1_1;
+ struct pad_desc sdhci2wp_gpio = MX51_PAD_GPIO_1_5__GPIO_1_5;
+ int ret;
+
+ /* Set SDHCI1_WP to GPIO1_1 */
+ mxc_iomux_v3_setup_pad(&sdhci1wp_gpio);
+ ret = gpio_request(BABBAGE_SDHCI1_WP, "sdhci1_wp");
+
+ if (ret) {
+ pr_debug("failed to get MX51_PAD_GPIO_1_1__GPIO1_1: %d\n", ret);
+ return ret;
+ }
+ /* Set SDHCI2_WP to GPIO1_5 */
+ mxc_iomux_v3_setup_pad(&sdhci2wp_gpio);
+ ret = gpio_request(BABBAGE_SDHCI1_WP, "sdhci2_wp");
+
+ if (ret) {
+ pr_debug("failed to get MX51_PAD_GPIO_1_5__GPIO1_5: %d\n", ret);
+ return ret;
+ }
+ gpio_direction_input(BABBAGE_SDHCI1_WP);
+ gpio_direction_input(BABBAGE_SDHCI2_WP);
+
+ if (to_platform_device(dev)->id == 0)
+ ret = gpio_get_value(BABBAGE_SDHCI1_WP);
+ else if (to_platform_device(dev)->id == 1)
+ ret = gpio_get_value(BABBAGE_SDHCI2_WP);
+
+ return ret;
+}
+
+ static struct imxmmc_platform_data mmc1_data = {
+ .caps = MMC_CAP_4_BIT_DATA,
+ .min_clk = 400000,
+ .max_clk = 52000000,
+ .wp_status = sdhc_write_protect,
+};
+
+ static struct imxmmc_platform_data mmc2_data = {
+ .caps = MMC_CAP_4_BIT_DATA,
+ .min_clk = 400000,
+ .max_clk = 52000000,
+ .wp_status = sdhc_write_protect,
+};
+
/*
* Board specific initialization.
*/
@@ -255,6 +323,8 @@ static void __init mxc_board_init(void)
mxc_register_device(&mxc_i2c_device0, &babbage_i2c_data);
mxc_register_device(&mxc_i2c_device1, &babbage_i2c_data);
mxc_register_device(&mxc_hsi2c_device, &babbage_hsi2c_data);
+ mxc_register_device(&mxcsdhc1_device, &mmc1_data);
+ mxc_register_device(&mxcsdhc2_device, &mmc2_data);
if (otg_mode_host)
mxc_register_device(&mxc_usbdr_host_device, &dr_utmi_config);
diff --git a/arch/arm/mach-mx5/clock-mx51.c b/arch/arm/mach-mx5/clock-mx51.c
index 6af69de..a7a8c3d 100644
--- a/arch/arm/mach-mx5/clock-mx51.c
+++ b/arch/arm/mach-mx5/clock-mx51.c
@@ -38,9 +38,40 @@ static struct clk periph_apm_clk;
static struct clk ahb_clk;
static struct clk ipg_clk;
static struct clk usboh3_clk;
+static struct clk esdhc1_clk[];
+static struct clk esdhc2_clk[];
#define MAX_DPLL_WAIT_TRIES 1000 /* 1000 * udelay(1) = 1ms */
+static void __calc_pre_post_dividers(u32 div, u32 *pre, u32 *post)
+{
+ u32 min_pre, temp_pre, old_err, err;
+
+ if (div >= 512) {
+ *pre = 8;
+ *post = 64;
+ } else if (div >= 8) {
+ min_pre = (div - 1) / 64 + 1;
+ old_err = 8;
+ for (temp_pre = 8; temp_pre >= min_pre; temp_pre--) {
+ err = div % temp_pre;
+ if (err == 0) {
+ *pre = temp_pre;
+ break;
+ }
+ err = temp_pre - err;
+ if (err < old_err) {
+ old_err = err;
+ *pre = temp_pre;
+ }
+ }
+ *post = (div + *pre - 1) / *pre;
+ } else if (div < 8) {
+ *pre = div;
+ *post = 1;
+ }
+}
+
static int _clk_ccgr_enable(struct clk *clk)
{
u32 reg;
@@ -762,6 +793,160 @@ static struct clk kpp_clk = {
.id = 0,
};
+static int _clk_esdhc1_set_parent(struct clk *clk, struct clk *parent)
+{
+ u32 reg, mux;
+ mux = _get_mux(parent, &pll1_sw_clk, &pll2_sw_clk,
+ &pll3_sw_clk, &lp_apm_clk);
+ reg = __raw_readl(MXC_CCM_CSCMR1) &
+ ~MXC_CCM_CSCMR1_ESDHC1_MSHC1_CLK_SEL_MASK;
+ reg |= mux << MXC_CCM_CSCMR1_ESDHC1_MSHC1_CLK_SEL_OFFSET;
+ __raw_writel(reg, MXC_CCM_CSCMR1);
+
+ return 0;
+}
+
+static unsigned long _clk_esdhc1_get_rate(struct clk *clk)
+{
+ u32 reg, prediv, podf;
+ unsigned long parent_rate;
+
+ parent_rate = clk_get_rate(clk->parent);
+
+ reg = __raw_readl(MXC_CCM_CSCDR1);
+ prediv = ((reg & MXC_CCM_CSCDR1_ESDHC1_MSHC1_CLK_PRED_MASK) >>
+ MXC_CCM_CSCDR1_ESDHC1_MSHC1_CLK_PRED_OFFSET) + 1;
+ podf = ((reg & MXC_CCM_CSCDR1_ESDHC1_MSHC1_CLK_PODF_MASK) >>
+ MXC_CCM_CSCDR1_ESDHC1_MSHC1_CLK_PODF_OFFSET) + 1;
+
+ return parent_rate / (prediv * podf);
+}
+
+static int _clk_esdhc1_set_rate(struct clk *clk, unsigned long rate)
+{
+ u32 reg, div, parent_rate;
+ u32 pre = 0, post = 0;
+
+ parent_rate = clk_get_rate(clk->parent);
+ div = parent_rate / rate;
+
+ if ((parent_rate / div) != rate)
+ return -EINVAL;
+
+ __calc_pre_post_dividers(div, &pre, &post);
+
+ /* Set sdhc1 clock divider */
+ reg = __raw_readl(MXC_CCM_CSCDR1) &
+ ~(MXC_CCM_CSCDR1_ESDHC1_MSHC1_CLK_PRED_MASK
+ | MXC_CCM_CSCDR1_ESDHC1_MSHC1_CLK_PODF_MASK);
+ reg |= (post - 1) << MXC_CCM_CSCDR1_ESDHC1_MSHC1_CLK_PODF_OFFSET;
+ reg |= (pre - 1) << MXC_CCM_CSCDR1_ESDHC1_MSHC1_CLK_PRED_OFFSET;
+ __raw_writel(reg, MXC_CCM_CSCDR1);
+
+ return 0;
+}
+
+static struct clk esdhc1_clk[] = {
+ {
+ .id = 0,
+ .parent = &pll2_sw_clk,
+ .secondary = &esdhc1_clk[1],
+ .enable_shift = MXC_CCM_CCGRx_CG1_OFFSET,
+ .enable_reg = MXC_CCM_CCGR3,
+ .get_rate = _clk_esdhc1_get_rate,
+ .set_rate = _clk_esdhc1_set_rate,
+ .enable = _clk_max_enable,
+ .disable = _clk_max_disable,
+ .set_parent = _clk_esdhc1_set_parent,
+ },
+ {
+ .id = 0,
+ .parent = &ipg_clk,
+ .secondary = NULL,
+ .enable = _clk_max_enable,
+ .enable_reg = MXC_CCM_CCGR3,
+ .enable_shift = MXC_CCM_CCGRx_CG0_OFFSET,
+ .disable = _clk_max_disable,
+ }
+};
+
+static int _clk_esdhc2_set_parent(struct clk *clk, struct clk *parent)
+{
+ u32 reg, mux;
+
+ mux = _get_mux(parent, &pll1_sw_clk, &pll2_sw_clk,
+ &pll3_sw_clk, &lp_apm_clk);
+ reg = __raw_readl(MXC_CCM_CSCMR1) &
+ ~MXC_CCM_CSCMR1_ESDHC2_MSHC2_CLK_SEL_MASK;
+ reg |= mux << MXC_CCM_CSCMR1_ESDHC2_MSHC2_CLK_SEL_OFFSET;
+
+ __raw_writel(reg, MXC_CCM_CSCMR1);
+ return 0;
+}
+
+static unsigned long _clk_esdhc2_get_rate(struct clk *clk)
+{
+ u32 reg, prediv, podf;
+ unsigned long parent_rate;
+
+ parent_rate = clk_get_rate(clk->parent);
+
+ reg = __raw_readl(MXC_CCM_CSCDR1);
+ prediv = ((reg & MXC_CCM_CSCDR1_ESDHC2_MSHC2_CLK_PRED_MASK) >>
+ MXC_CCM_CSCDR1_ESDHC2_MSHC2_CLK_PRED_OFFSET) + 1;
+ podf = ((reg & MXC_CCM_CSCDR1_ESDHC2_MSHC2_CLK_PODF_MASK) >>
+ MXC_CCM_CSCDR1_ESDHC2_MSHC2_CLK_PODF_OFFSET) + 1;
+
+ return parent_rate / (prediv * podf);
+}
+
+static int _clk_esdhc2_set_rate(struct clk *clk, unsigned long rate)
+{
+ u32 reg, div, parent_rate;
+ u32 pre = 0, post = 0;
+
+ parent_rate = clk_get_rate(clk->parent);
+ div = parent_rate / rate;
+ if ((parent_rate / div) != rate)
+ return -EINVAL;
+
+ __calc_pre_post_dividers(div, &pre, &post);
+
+ /* Set sdhc1 clock divider */
+ reg = __raw_readl(MXC_CCM_CSCDR1) &
+ ~(MXC_CCM_CSCDR1_ESDHC2_MSHC2_CLK_PRED_MASK
+ | MXC_CCM_CSCDR1_ESDHC2_MSHC2_CLK_PODF_MASK);
+ reg |= (post - 1) << MXC_CCM_CSCDR1_ESDHC2_MSHC2_CLK_PODF_OFFSET;
+ reg |= (pre - 1) << MXC_CCM_CSCDR1_ESDHC2_MSHC2_CLK_PRED_OFFSET;
+ __raw_writel(reg, MXC_CCM_CSCDR1);
+
+ return 0;
+}
+
+static struct clk esdhc2_clk[] = {
+ {
+ .id = 1,
+ .parent = &pll2_sw_clk,
+ .secondary = &esdhc2_clk[1],
+ .enable_shift = MXC_CCM_CCGRx_CG3_OFFSET,
+ .enable_reg = MXC_CCM_CCGR3,
+ .get_rate = _clk_esdhc2_get_rate,
+ .set_rate = _clk_esdhc2_set_rate,
+ .enable = _clk_max_enable,
+ .disable = _clk_max_disable,
+ .set_parent = _clk_esdhc2_set_parent,
+ },
+ {
+ .id = 1,
+ .parent = &ipg_clk,
+ .secondary = NULL,
+ .enable_shift = MXC_CCM_CCGRx_CG2_OFFSET,
+ .enable_reg = MXC_CCM_CCGR3,
+ .enable = _clk_max_enable,
+ .disable = _clk_max_disable,
+ }
+};
+
#define DEFINE_CLOCK(name, i, er, es, gr, sr, p, s) \
static struct clk name = { \
.id = i, \
@@ -837,6 +1022,10 @@ static struct clk_lookup lookups[] = {
_REGISTER_CLOCK("fsl-usb2-udc", "usb", usboh3_clk)
_REGISTER_CLOCK("fsl-usb2-udc", "usb_ahb", ahb_clk)
_REGISTER_CLOCK("imx-keypad.0", NULL, kpp_clk)
+ _REGISTER_CLOCK("imx-sdhci.0", "esdhc_clk", esdhc1_clk[0])
+ _REGISTER_CLOCK("imx-sdhci.0", "esdhc_ipg_clk", esdhc1_clk[1])
+ _REGISTER_CLOCK("imx-sdhci.1", "esdhc_clk", esdhc2_clk[0])
+ _REGISTER_CLOCK("imx-sdhci.1", "esdhc_ipg_clk", esdhc2_clk[1])
};
static void clk_tree_init(void)
@@ -880,6 +1069,14 @@ int __init mx51_clocks_init(unsigned long ckil, unsigned long osc,
/* set the usboh3_clk parent to pll2_sw_clk */
clk_set_parent(&usboh3_clk, &pll2_sw_clk);
+ /* Set SDHC parents to be PLL2 */
+ clk_set_parent(&esdhc1_clk[0], &pll2_sw_clk);
+ clk_set_parent(&esdhc2_clk[0], &pll2_sw_clk);
+
+ /* set SDHC root clock as 166.25MHZ*/
+ clk_set_rate(&esdhc1_clk[0], 166250000);
+ clk_set_rate(&esdhc2_clk[0], 166250000);
+
/* System timer */
mxc_timer_init(&gpt_clk, MX51_IO_ADDRESS(MX51_GPT1_BASE_ADDR),
MX51_MXC_INT_GPT);
diff --git a/arch/arm/mach-mx5/devices.c b/arch/arm/mach-mx5/devices.c
index 1920ff4..bf553b0 100644
--- a/arch/arm/mach-mx5/devices.c
+++ b/arch/arm/mach-mx5/devices.c
@@ -245,6 +245,58 @@ struct platform_device mxc_keypad_device = {
.resource = mxc_kpp_resources,
};
+static struct resource mxcsdhc1_resources[] = {
+ {
+ .start = MX51_MMC_SDHC1_BASE_ADDR,
+ .end = MX51_MMC_SDHC1_BASE_ADDR + SZ_4K - 1,
+ .flags = IORESOURCE_MEM,
+ },
+ {
+ .start = MX51_MXC_INT_MMC_SDHC1,
+ .end = MX51_MXC_INT_MMC_SDHC1,
+ .flags = IORESOURCE_IRQ,
+ },
+ {
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct resource mxcsdhc2_resources[] = {
+ {
+ .start = MX51_MMC_SDHC2_BASE_ADDR,
+ .end = MX51_MMC_SDHC2_BASE_ADDR + SZ_4K - 1,
+ .flags = IORESOURCE_MEM,
+ },
+ {
+ .start = MX51_MXC_INT_MMC_SDHC2,
+ .end = MX51_MXC_INT_MMC_SDHC2,
+ .flags = IORESOURCE_IRQ,
+ },
+ {
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+ struct platform_device mxcsdhc1_device = {
+ .name = "imx-sdhci",
+ .id = 0,
+ .num_resources = ARRAY_SIZE(mxcsdhc1_resources),
+ .resource = mxcsdhc1_resources,
+ .dev = {
+ .coherent_dma_mask = DMA_BIT_MASK(32),
+ },
+};
+
+ struct platform_device mxcsdhc2_device = {
+ .name = "imx-sdhci",
+ .id = 1,
+ .num_resources = ARRAY_SIZE(mxcsdhc2_resources),
+ .resource = mxcsdhc2_resources,
+ .dev = {
+ .coherent_dma_mask = DMA_BIT_MASK(32),
+ },
+};
+
static struct mxc_gpio_port mxc_gpio_ports[] = {
{
.chip.label = "gpio-0",
diff --git a/arch/arm/mach-mx5/devices.h b/arch/arm/mach-mx5/devices.h
index e509cfa..21b9a6f 100644
--- a/arch/arm/mach-mx5/devices.h
+++ b/arch/arm/mach-mx5/devices.h
@@ -10,3 +10,5 @@ extern struct platform_device mxc_i2c_device0;
extern struct platform_device mxc_i2c_device1;
extern struct platform_device mxc_hsi2c_device;
extern struct platform_device mxc_keypad_device;
+extern struct platform_device mxcsdhc1_device;
+extern struct platform_device mxcsdhc2_device;
--
1.7.0
More information about the linux-arm-kernel
mailing list