Grant Edwards ha scritto:
> On 2010-10-19, Alexander Stein <alexander.stein at systec-electronic.com> wrote:
>> On Tuesday 19 October 2010, 16:29:48 Grant Edwards wrote:
>>> On 2010-10-19, Claudio Scordino <claudio at evidence.eu.com> wrote:
>>>> +2. HARDWARE-RELATED CONSIDERATIONS
>>>> +
>>>> + Some CPUs (e.g., Atmel AT91) contain a transceiver capable of working
>>>> both + as RS232 and RS485.
>>> Pardon my curiosity, but I've looked at a few AT91 parts, and I've
>>> never seen on with an internal transceiver -- nor does Google seem
>>> able to find any.
>>>
>>> Frankly, I'd be pretty surprised, since it would be very difficult
>>> (fab-wise), to build a mircoprocessor with I/O cells capable of
>>> withstanding the voltage levels specified in RS232.
>>>
>>> Can you specify to which parts you're referring?
>> I doubt the AT91 do have an internal transceiver but it has a
>> dedicated pin feature (RTS or CTS or something) which can be used to
>> switch between RS232 and RS485 by setting a bit in the USART provided
>> the pin is connected properly.
>
> Yes, the AT91 UARTs do have a built-in half-duplex mode that will
> automatically control line direction by toggling RTS.
>
> That can used to control external half-duplex hardware like an RS485
> transceiver or any RS232-connected half-duplex device like some
> modems.
>
> Though the Atmel docs refer to it as "RS485 mode" there is no RS485
> transceiver in the AT91 parts (AFAIK), and "RS485 mode" isn't specific
> to RS485 - it can be used with any external half-duplex hardware.
Hi all,
sorry for the misuse of the term "transceiver", and thank you
for your corrections.
Hopefully, this new version of the document is slightly better.
Many thanks,
Claudio
Documentation about RS485 serial communications
Signed-off-by: Claudio Scordino <claudio at evidence.eu.com>
---
Documentation/serial/00-INDEX | 2 +
Documentation/serial/serial-rs485.txt | 119 +++++++++++++++++++++++++++++++++
2 files changed, 121 insertions(+), 0 deletions(-)
create mode 100644 Documentation/serial/serial-rs485.txt
diff --git a/Documentation/serial/00-INDEX b/Documentation/serial/00-INDEX
index 07dcdb0..e09468a 100644
--- a/Documentation/serial/00-INDEX
+++ b/Documentation/serial/00-INDEX
@@ -14,6 +14,8 @@ riscom8.txt
- notes on using the RISCom/8 multi-port serial driver.
rocket.txt
- info on the Comtrol RocketPort multiport serial driver.
+serial-rs485.txt
+ - info about RS485 structures and support in the kernel.
specialix.txt
- info on hardware/driver for specialix IO8+ multiport serial card.
stallion.txt
diff --git a/Documentation/serial/serial-rs485.txt b/Documentation/serial/serial-rs485.txt
new file mode 100644
index 0000000..40f09c6
--- /dev/null
+++ b/Documentation/serial/serial-rs485.txt
@@ -0,0 +1,119 @@
+ RS485 SERIAL COMMUNICATIONS
+
+1. INTRODUCTION
+
+ EIA-485, also known as TIA/EIA-485 or RS-485, is a standard defining the
+ electrical characteristics of drivers and receivers for use in balanced
+ digital multipoint systems.
+ This standard is widely used for communications in industrial automation
+ because it can be used effectively over long distances and in electrically
+ noisy environments.
+
+2. HARDWARE-RELATED CONSIDERATIONS
+
+ Some CPUs (e.g., Atmel AT91) contain a built-in half-duplex mode capable of
+ automatically controlling line direction by toggling RTS. That can used to
+ control external half-duplex hardware like an RS485 transceiver or any
+ RS232-connected half-duplex device like some modems.
+
+ For these microcontrollers, the Linux driver should be made capable of
+ working in both modes, and proper ioctls (see later) should be made
+ available at user-level to allow switching from one mode to the other, and
+ vice versa.
+
+3. DATA STRUCTURES ALREADY AVAILABLE IN THE KERNEL
+
+ The Linux kernel provides the serial_rs485 structure (see [1]) to handle
+ RS485 communications. This data structure is used to set and configure RS485
+ parameters in the platform data and in ioctls.
+
+ Any driver for devices capable of working both as RS232 and RS485 should
+ provide at least the following ioctls:
+
+ - TIOCSRS485 (typically associated with number 0x542F). This ioctl is used
+ to enable/disable RS485 mode from user-space
+
+ - TIOCGRS485 (typically associated with number 0x542E). This ioctl is used
+ to get RS485 mode from kernel-space (i.e., driver) to user-space.
+
+ In other words, the serial driver should contain a code similar to the next
+ one:
+
+ static struct uart_ops atmel_pops = {
+ /* ... */
+ .ioctl = handle_ioctl,
+ };
+
+ static int handle_ioctl(struct uart_port *port,
+ unsigned int cmd,
+ unsigned long arg)
+ {
+ struct serial_rs485 rs485conf;
+
+ switch (cmd) {
+ case TIOCSRS485:
+ if (copy_from_user(&rs485conf,
+ (struct serial_rs485 *) arg,
+ sizeof(rs485conf)))
+ return -EFAULT;
+
+ /* ... */
+ break;
+
+ case TIOCGRS485:
+ if (copy_to_user((struct serial_rs485 *) arg,
+ ...,
+ sizeof(rs485conf)))
+ return -EFAULT;
+ /* ... */
+ break;
+
+ /* ... */
+ }
+ }
+
+
+4. USAGE FROM USER-LEVEL
+
+ From user-level, RS485 configuration can be get/set using the previous
+ ioctls. For instance, to set RS485 you can use the following code:
+
+ #include <linux/serial.h>
+
+ /* Driver-specific ioctls: */
+ #define TIOCGRS485 0x542E
+ #define TIOCSRS485 0x542F
+
+ /* Open your specific device (e.g., /dev/mydevice): */
+ int fd = open ("/dev/mydevice", O_RDWR);
+ if (fd < 0) {
+ /* Error handling. See errno. */
+ }
+
+ struct serial_rs485 rs485conf;
+
+ /* Set RS485 mode: */
+ rs485conf.flags |= SER_RS485_ENABLED;
+
+ /* Set rts delay before send, if needed: */
+ rs485conf.flags |= SER_RS485_RTS_BEFORE_SEND;
+ rs485conf.delay_rts_before_send = ...;
+
+ /* Set rts delay after send, if needed: */
+ rs485conf.flags |= SER_RS485_RTS_AFTER_SEND;
+ rs485conf.delay_rts_after_send = ...;
+
+ if (ioctl (fd, TIOCSRS485, &rs485conf) < 0) {
+ /* Error handling. See errno. */
+ }
+
+ /* Use read() and write() syscalls here... */
+
+ /* Close the device when finished: */
+ if (close (fd) < 0) {
+ /* Error handling. See errno. */
+ }
+
+5. REFERENCES
+
+ [1] include/linux/serial.h
--
1.6.0.4