[PATCH 3/4] s3c-fb: Add support S5PV310 FIMD

Marek Szyprowski m.szyprowski at samsung.com
Tue Oct 19 03:22:14 EDT 2010


1AFAAVgAzADEAMAAgAEY
	ASQBNAEQA
x-cr-puzzleid: {C4CCB40E-D5C6-4119-AA7C-BBBA7A1503E4}

Hello,

On Monday, October 18, 2010 2:55 PM Sangbeom Kim wrote:

> From: Jonghun Han <jonghun.han at samsung.com>
> 
> This patch adds s3c_fb_driverdata for S5PV310 FIMD0. The clk_type is added
> to distinguish clock type in structure s3c_fb_variant and lcd_clk is added
> in structure s3c_fb to calculate divider for lcd panel.
> FIMD can handles two clocks. The one is for FIMD IP and the other is for
> LCD pixel clock. Before S5PV310 LCD pixel clock can be same with FIMD IP
> clock. From S5PV310 LCD pixel clock is separated from FIMD IP clock.
> 
> Signed-off-by: Jonghun Han <jonghun.han at samsung.com>
> Reviewed-by: Kukjin Kim <kgene.kim at samsung.com>
> Signed-off-by: Sangbeom Kim <sbkim73 at samsung.com>
> Cc: Ben Dooks <ben-linux at fluff.org>
> ---
> NOTE: This patch is only for FIMD0.
> FIMD1 will be implemented later.
>  drivers/video/Kconfig  |    2 +-
>  drivers/video/s3c-fb.c |  128 ++++++++++++++++++++++++++++++++++++++++++------
>  2 files changed, 114 insertions(+), 16 deletions(-)
> 
> diff --git a/drivers/video/Kconfig b/drivers/video/Kconfig
> index 8b31fdf..3e2e02a 100644
> --- a/drivers/video/Kconfig
> +++ b/drivers/video/Kconfig
> @@ -1946,7 +1946,7 @@ config FB_TMIO_ACCELL
> 
>  config FB_S3C
>  	tristate "Samsung S3C framebuffer support"
> -	depends on FB && S3C_DEV_FB
> +	depends on FB && (S3C_DEV_FB || S5P_DEV_FIMD0)
>  	select FB_CFB_FILLRECT
>  	select FB_CFB_COPYAREA
>  	select FB_CFB_IMAGEBLIT
> diff --git a/drivers/video/s3c-fb.c b/drivers/video/s3c-fb.c
> index f9aca9d..bc182ea 100644
> --- a/drivers/video/s3c-fb.c
> +++ b/drivers/video/s3c-fb.c
> @@ -65,6 +65,9 @@ struct s3c_fb;
>  #define VIDOSD_C(win, variant) (OSD_BASE(win, variant) + 0x08)
>  #define VIDOSD_D(win, variant) (OSD_BASE(win, variant) + 0x0C)
> 
> +#define FIMD_CLK_TYPE0	0
> +#define FIMD_CLK_TYPE1	1
> +
>  /**
>   * struct s3c_fb_variant - fb variant information
>   * @is_2443: Set if S3C2443/S3C2416 style hardware.
> @@ -97,6 +100,7 @@ struct s3c_fb_variant {
> 
>  	unsigned int	has_prtcon:1;
>  	unsigned int	has_shadowcon:1;
> +	unsigned int	clk_type:1;
>  };
> 
>  /**
> @@ -183,7 +187,8 @@ struct s3c_fb_vsync {
>   * struct s3c_fb - overall hardware state of the hardware
>   * @dev: The device that we bound to, for printing, etc.
>   * @regs_res: The resource we claimed for the IO registers.
> - * @bus_clk: The clk (hclk) feeding our interface and possibly pixclk.
> + * @bus_clk: The clk (hclk) feeding FIMD IP core.
> + * @lcd_clk: The clk (sclk) feeding our interface and possibly pixclk.
>   * @regs: The mapped hardware registers.
>   * @variant: Variant information for this hardware.
>   * @enabled: A bitmask of enabled hardware windows.
> @@ -197,6 +202,7 @@ struct s3c_fb {
>  	struct device		*dev;
>  	struct resource		*regs_res;
>  	struct clk		*bus_clk;
> +	struct clk		*lcd_clk;
>  	void __iomem		*regs;
>  	struct s3c_fb_variant	 variant;
> 
> @@ -334,7 +340,7 @@ static int s3c_fb_check_var(struct fb_var_screeninfo *var,
>   */
>  static int s3c_fb_calc_pixclk(struct s3c_fb *sfb, unsigned int pixclk)
>  {
> -	unsigned long clk = clk_get_rate(sfb->bus_clk);
> +	unsigned long clk = clk_get_rate(sfb->lcd_clk);
>  	unsigned long long tmp;
>  	unsigned int result;
> 
> @@ -517,7 +523,7 @@ static int s3c_fb_set_par(struct fb_info *info)
> 
>  		data = VIDTCON2_LINEVAL(var->yres - 1) |
>  		       VIDTCON2_HOZVAL(var->xres - 1);
> -		writel(data, regs +sfb->variant.vidtcon + 8 );
> +		writel(data, regs + sfb->variant.vidtcon + 8);
>  	}
> 
>  	/* write the buffer address */
> @@ -1286,8 +1292,10 @@ static int __devinit s3c_fb_probe(struct platform_device *pdev)
>  	struct s3c_fb_platdata *pd;
>  	struct s3c_fb *sfb;
>  	struct resource *res;
> +	struct clk *mout_mpll = NULL;
>  	int win;
>  	int ret = 0;
> +	u32 rate = 134000000;
> 
>  	fbdrv = (struct s3c_fb_driverdata *)platform_get_device_id(pdev)->driver_data;
> 
> @@ -1314,19 +1322,56 @@ static int __devinit s3c_fb_probe(struct platform_device *pdev)
>  	sfb->pdata = pd;
>  	sfb->variant = fbdrv->variant;
> 
> -	sfb->bus_clk = clk_get(dev, "lcd");
> -	if (IS_ERR(sfb->bus_clk)) {
> -		dev_err(dev, "failed to get bus clock\n");
> +	switch (sfb->variant.clk_type) {
> +	case FIMD_CLK_TYPE0:
> +		sfb->bus_clk = clk_get(dev, "lcd");
> +		if (IS_ERR(sfb->bus_clk)) {
> +			dev_err(dev, "failed to get bus clock\n");
> +			goto err_sfb;
> +		}
> +
> +		clk_enable(sfb->bus_clk);
> +
> +		sfb->lcd_clk = sfb->bus_clk;
> +		break;
> +
> +	case FIMD_CLK_TYPE1:
> +		sfb->bus_clk = clk_get(&pdev->dev, "fimd");
> +		if (IS_ERR(sfb->bus_clk)) {
> +			dev_err(&pdev->dev, "failed to get clock for fimd\n");
> +			goto err_sfb;
> +		}
> +		clk_enable(sfb->bus_clk);
> +
> +		sfb->lcd_clk = clk_get(&pdev->dev, "sclk_fimd");
> +		if (IS_ERR(sfb->lcd_clk)) {
> +			dev_err(&pdev->dev, "failed to get sclk for fimd\n");
> +			goto err_bus_clk;
> +		}
> +
> +		mout_mpll = clk_get(&pdev->dev, "mout_mpll");
> +		if (IS_ERR(mout_mpll)) {
> +			dev_err(&pdev->dev, "failed to get mout_mpll\n");
> +			goto err_lcd_clk;
> +		}
> +		clk_set_parent(sfb->lcd_clk, mout_mpll);
> +		clk_put(mout_mpll);

I don't think that the driver is the right place to change the parent of the sclk_fimd
clock. It should be done in the boot loader or the board startup code.

We should also be a bit more consistent on clock naming. s3c6410..s5pv210 used the 'lcd'
clock name. Maybe you should also provide a patch to rename all these clocks to common
name.

> +
> +		clk_set_rate(sfb->lcd_clk, rate);
> +		clk_enable(sfb->lcd_clk);
> +		dev_dbg(&pdev->dev, "set fimd sclk rate to %d\n", rate);
> +		break;
> +
> +	default:
> +		dev_err(dev, "failed to enable clock for FIMD\n");
>  		goto err_sfb;
>  	}
> 
> -	clk_enable(sfb->bus_clk);
> -
>  	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
>  	if (!res) {
>  		dev_err(dev, "failed to find registers\n");
>  		ret = -ENOENT;
> -		goto err_clk;
> +		goto err_lcd_clk;
>  	}
> 
>  	sfb->regs_res = request_mem_region(res->start, resource_size(res),
> @@ -1334,7 +1379,7 @@ static int __devinit s3c_fb_probe(struct platform_device *pdev)
>  	if (!sfb->regs_res) {
>  		dev_err(dev, "failed to claim register region\n");
>  		ret = -ENOENT;
> -		goto err_clk;
> +		goto err_lcd_clk;
>  	}
> 
>  	sfb->regs = ioremap(res->start, resource_size(res));
> @@ -1413,9 +1458,15 @@ err_req_region:
>  	release_resource(sfb->regs_res);
>  	kfree(sfb->regs_res);
> 
> -err_clk:
> -	clk_disable(sfb->bus_clk);
> -	clk_put(sfb->bus_clk);
> +err_lcd_clk:
> +	clk_disable(sfb->lcd_clk);
> +	clk_put(sfb->lcd_clk);
> +
> +err_bus_clk:
> +	if (sfb->variant.clk_type != FIMD_CLK_TYPE0) {
> +		clk_disable(sfb->bus_clk);
> +		clk_put(sfb->bus_clk);
> +	}
> 
>  err_sfb:
>  	kfree(sfb);
> @@ -1442,8 +1493,20 @@ static int __devexit s3c_fb_remove(struct platform_device *pdev)
> 
>  	iounmap(sfb->regs);
> 
> -	clk_disable(sfb->bus_clk);
> -	clk_put(sfb->bus_clk);
> +	switch (sfb->variant.clk_type) {
> +	case FIMD_CLK_TYPE1:
> +		clk_disable(sfb->lcd_clk);
> +		clk_put(sfb->lcd_clk);
> +		/* fall through to default case */
> +	case FIMD_CLK_TYPE0:
> +		clk_disable(sfb->bus_clk);
> +		clk_put(sfb->bus_clk);
> +		break;
> +	default:
> +		dev_err(sfb->dev, "invalid clock type(%d)\n",
> +			sfb->variant.clk_type);
> +		break;
> +	}
> 
>  	release_resource(sfb->regs_res);
>  	kfree(sfb->regs_res);
> @@ -1470,6 +1533,7 @@ static int s3c_fb_suspend(struct platform_device *pdev, pm_message_t state)
>  	}
> 
>  	clk_disable(sfb->bus_clk);
> +
>  	return 0;
>  }
> 
> @@ -1656,6 +1720,37 @@ static struct s3c_fb_driverdata s3c_fb_data_s5pv210 = {
>  	.win[4]	= &s3c_fb_data_64xx_wins[4],
>  };
> 
> +static struct s3c_fb_driverdata s3c_fb_data_s5pv310 = {
> +	.variant = {
> +		.nr_windows	= 5,
> +		.vidtcon	= VIDTCON0,
> +		.wincon		= WINCON(0),
> +		.winmap		= WINxMAP(0),
> +		.keycon		= WKEYCON,
> +		.osd		= VIDOSD_BASE,
> +		.osd_stride	= 16,
> +		.buf_start	= VIDW_BUF_START(0),
> +		.buf_size	= VIDW_BUF_SIZE(0),
> +		.buf_end	= VIDW_BUF_END(0),
> +
> +		.palette = {
> +			[0] = 0x2400,
> +			[1] = 0x2800,
> +			[2] = 0x2c00,
> +			[3] = 0x3000,
> +			[4] = 0x3400,
> +		},
> +
> +		.has_shadowcon	= 1,
> +		.clk_type	= FIMD_CLK_TYPE1,
> +	},
> +	.win[0]	= &s3c_fb_data_64xx_wins[0],
> +	.win[1]	= &s3c_fb_data_64xx_wins[1],
> +	.win[2]	= &s3c_fb_data_64xx_wins[2],
> +	.win[3]	= &s3c_fb_data_64xx_wins[3],
> +	.win[4]	= &s3c_fb_data_64xx_wins[4],
> +};
> +
>  /* S3C2443/S3C2416 style hardware */
>  static struct s3c_fb_driverdata s3c_fb_data_s3c2443 = {
>  	.variant = {
> @@ -1703,6 +1798,9 @@ static struct platform_device_id s3c_fb_driver_ids[] = {
>  		.name		= "s5pv210-fb",
>  		.driver_data	= (unsigned long)&s3c_fb_data_s5pv210,
>  	}, {
> +		.name		= "s5pv310-fb",
> +		.driver_data	= (unsigned long)&s3c_fb_data_s5pv310,
> +	}, {
>  		.name		= "s3c2443-fb",
>  		.driver_data	= (unsigned long)&s3c_fb_data_s3c2443,
>  	},
> --

Best regards
--
Marek Szyprowski
Samsung Poland R&D Center





More information about the linux-arm-kernel mailing list