[PATCHv2 2/2] ARM: imx: Add gpio-keys to mx51 babbage board

[Uwe Kleine-König]

Hello Dinh,

On Mon, Oct 18, 2010 at 11:35:31AM -0500, Dinh.Nguyen at freescale.com wrote:
> From: Dinh Nguyen <Dinh.Nguyen at freescale.com>
> 
> Add functionality for the power button on MX51 Babbage board.
> 
> Signed-off-by: Dinh Nguyen <Dinh.Nguyen at freescale.com>
> ---
>  arch/arm/configs/mx51_defconfig             |    1 +
>  arch/arm/mach-mx5/board-mx51_babbage.c      |   33 +++++++++++++++++++++++++++
>  arch/arm/plat-mxc/include/mach/iomux-mx51.h |    4 ++-
>  3 files changed, 37 insertions(+), 1 deletions(-)
> 
> diff --git a/arch/arm/configs/mx51_defconfig b/arch/arm/configs/mx51_defconfig
> index a665ecb..f46f87e 100644
> --- a/arch/arm/configs/mx51_defconfig
> +++ b/arch/arm/configs/mx51_defconfig
> @@ -81,6 +81,7 @@ CONFIG_FEC=y
>  CONFIG_INPUT_FF_MEMLESS=m
>  # CONFIG_INPUT_MOUSEDEV_PSAUX is not set
>  CONFIG_INPUT_EVDEV=y
> +CONFIG_KEYBOARD_GPIO=y
>  CONFIG_INPUT_EVBUG=m
>  CONFIG_MOUSE_PS2=m
>  CONFIG_MOUSE_PS2_ELANTECH=y
nice

> diff --git a/arch/arm/mach-mx5/board-mx51_babbage.c b/arch/arm/mach-mx5/board-mx51_babbage.c
> index 6e384d9..0dded49 100644
> --- a/arch/arm/mach-mx5/board-mx51_babbage.c
> +++ b/arch/arm/mach-mx5/board-mx51_babbage.c
> @@ -16,7 +16,11 @@
>  #include <linux/gpio.h>
>  #include <linux/delay.h>
>  #include <linux/io.h>
> +#include <linux/interrupt.h>
> +#include <linux/irq.h>
>  #include <linux/fsl_devices.h>
> +#include <linux/gpio_keys.h>
> +#include <linux/input.h>
>  
>  #include <mach/common.h>
>  #include <mach/hardware.h>
> @@ -36,6 +40,7 @@
>  #define BABBAGE_USB_HUB_RESET	(0*32 + 7)	/* GPIO_1_7 */
>  #define BABBAGE_USBH1_STP	(0*32 + 27)	/* GPIO_1_27 */
>  #define BABBAGE_PHY_RESET (1*32 +5)	/* GPIO_2_5 */
> +#define BABBAGE_POWER_KEY	(1*32 + 21)	/* GPIO_2_21 */
>  
>  /* USB_CTRL_1 */
>  #define MX51_USB_CTRL_1_OFFSET			0x10
> @@ -45,8 +50,33 @@
>  #define	MX51_USB_PLL_DIV_19_2_MHZ	0x01
>  #define	MX51_USB_PLL_DIV_24_MHZ	0x02
>  
> +static struct gpio_keys_button babbage_buttons[] = {
> +	{
> +		.gpio		= BABBAGE_POWER_KEY,
> +		.code		= BTN_0,
> +		.desc		= "PWR",
> +		.active_low	= 1,
> +		.wakeup		= 1,
> +	},
> +};
> +
> +static struct gpio_keys_platform_data babbage_button_data = {
> +	.buttons	= babbage_buttons,
> +	.nbuttons	= ARRAY_SIZE(babbage_buttons),
> +};
> +
> +static struct platform_device babbage_button_device = {
> +	.name		= "gpio-keys",
> +	.id		= -1,
> +	.num_resources	= 0,
> +	.dev		= {
> +		.platform_data	= &babbage_button_data,
> +	}
> +};
> +
>  static struct platform_device *devices[] __initdata = {
>  	&mxc_fec_device,
> +	&babbage_button_device,
I think this won't fit on top of Sascha's tree as it has a patch that
changed the way the fec is registered.

>  };
>  
>  static struct pad_desc mx51babbage_pads[] = {
> @@ -93,6 +123,9 @@ static struct pad_desc mx51babbage_pads[] = {
>  
>  	/* USB HUB reset line*/
>  	MX51_PAD_GPIO_1_7__GPIO_1_7,
> +
> +	/* Power Key */
> +	MX51_PAD_EIM_A27__GPIO_2_21,
>  };
>  
>  /* Serial ports */
> diff --git a/arch/arm/plat-mxc/include/mach/iomux-mx51.h b/arch/arm/plat-mxc/include/mach/iomux-mx51.h
> index 21bfa46..05f62a4 100644
> --- a/arch/arm/plat-mxc/include/mach/iomux-mx51.h
> +++ b/arch/arm/plat-mxc/include/mach/iomux-mx51.h
> @@ -31,6 +31,8 @@ typedef enum iomux_config {
>  	IOMUX_CONFIG_SION = 0x1 << 4,   /* LOOPBACK:MUX SION bit */
>  } iomux_pin_cfg_t;
>  
> +#define IOMUX_TO_IRQ(pin)	(MXC_GPIO_IRQ_START + pin)
> +
This isn't used.  (Didn't check patch 1, it should go there if it is
needed.)

>  /* Pad control groupings */
>  #define MX51_UART1_PAD_CTRL	(PAD_CTL_HYS | PAD_CTL_PKE | PAD_CTL_PUE | \
>  				PAD_CTL_DSE_HIGH)
> @@ -102,7 +104,7 @@ typedef enum iomux_config {
>  #define MX51_PAD_EIM_A24__GPIO_2_18             IOMUX_PAD(0x450, 0x0bc, 1, 0x0,   0, NO_PAD_CTRL)
>  #define MX51_PAD_EIM_A25__GPIO_2_19             IOMUX_PAD(0x454, 0x0c0, 1, 0x0,   0, NO_PAD_CTRL)
>  #define MX51_PAD_EIM_A26__GPIO_2_20             IOMUX_PAD(0x458, 0x0c4, 1, 0x0,   0, NO_PAD_CTRL)
> -#define MX51_PAD_EIM_A27__GPIO_2_21             IOMUX_PAD(0x45c, 0x0c8, 1, 0x0,   0, NO_PAD_CTRL)
> +#define MX51_PAD_EIM_A27__GPIO_2_21             IOMUX_PAD(0x45c, 0x0c8, 1, 0x0,   0, MX51_I2C_PAD_CTRL)
This looks wrong.  Isn't there a MX51_GPIO_PAD_CTRL?
>  #define MX51_PAD_EIM_EB0__EIM_EB0               IOMUX_PAD(0x460, 0x0cc, 0, 0x0,   0, NO_PAD_CTRL)
>  #define MX51_PAD_EIM_EB1__EIM_EB1               IOMUX_PAD(0x464, 0x0d0, 0, 0x0,   0, NO_PAD_CTRL)
>  #define MX51_PAD_EIM_EB2__GPIO_2_22             IOMUX_PAD(0x468, 0x0d4, 1, 0x0,   0, NO_PAD_CTRL)

Best regards
Uwe

-- 
Pengutronix e.K.                           | Uwe Kleine-König            |
Industrial Linux Solutions                 | http://www.pengutronix.de/  |