[PATCH] Input: Make ADS7846 independent on regulator

[Linus Walleij]

2010/7/31 Marek Vasut <marek.vasut at gmail.com>:

> This fixes a problem on some Sharp Zaurus devices, where there is no regulator
> present and yet the touchscreen is used.
>
> Signed-off-by: Marek Vasut <marek.vasut at gmail.com>
> ---
>  drivers/input/touchscreen/ads7846.c |   50 +++++++++++++++++++++++------------
>  1 files changed, 33 insertions(+), 17 deletions(-)
>
> diff --git a/drivers/input/touchscreen/ads7846.c b/drivers/input/touchscreen/ads7846.c
> index a9fdf55..dafaef6 100644
> --- a/drivers/input/touchscreen/ads7846.c
> +++ b/drivers/input/touchscreen/ads7846.c
> @@ -791,7 +791,10 @@ static void ads7846_disable(struct ads7846 *ts)
>                }
>        }
>
> -       regulator_disable(ts->reg);
> +#ifdef CONFIG_REGULATOR

Skip the #ifdef, if the regulators are configured out, there will be
a stub providing NULL for all get_regulator() calls anyway.

> +       if (ts->reg)
> +               regulator_disable(ts->reg);
> +#endif
>
>        /* we know the chip's in lowpower mode since we always
>         * leave it that way after every request
> @@ -804,7 +807,10 @@ static void ads7846_enable(struct ads7846 *ts)
>        if (!ts->disabled)
>                return;
>
> -       regulator_enable(ts->reg);
> +#ifdef CONFIG_REGULATOR

Skip the #ifdef.

> +       if (ts->reg)
> +               regulator_enable(ts->reg);
> +#endif
>
>        ts->disabled = 0;
>        ts->irq_disabled = 0;
> @@ -1161,18 +1167,21 @@ static int __devinit ads7846_probe(struct spi_device *spi)
>
>        ts->last_msg = m;
>
> +#ifdef CONFIG_REGULATOR

Skip the #ifdef.

>        ts->reg = regulator_get(&spi->dev, "vcc");
> -       if (IS_ERR(ts->reg)) {
> -               err = PTR_ERR(ts->reg);
> -               dev_err(&spi->dev, "unable to get regulator: %d\n", err);
> -               goto err_free_gpio;
> -       }
> -
> -       err = regulator_enable(ts->reg);
> -       if (err) {
> -               dev_err(&spi->dev, "unable to enable regulator: %d\n", err);
> -               goto err_put_regulator;
> +       if (IS_ERR(ts->reg))
> +               ts->reg = NULL;
> +       else {
> +               err = regulator_enable(ts->reg);
> +               if (err) {
> +                       dev_err(&spi->dev, "unable to enable regulator: %d\n",
> +                               err);
> +                       goto err_put_regulator;
> +               }
>        }
> +#else
> +       ts->reg = NULL;
> +#endif

Delete the #else/#endif clause entirely.

>
>        if (request_irq(spi->irq, ads7846_irq, IRQF_TRIGGER_FALLING,
>                        spi->dev.driver->name, ts)) {
> @@ -1218,10 +1227,13 @@ static int __devinit ads7846_probe(struct spi_device *spi)
>  err_free_irq:
>        free_irq(spi->irq, ts);
>  err_disable_regulator:
> -       regulator_disable(ts->reg);
> +#ifdef CONFIG_REGULATOR

Skip the #ifdef.

> +       if (ts->reg)
> +               regulator_disable(ts->reg);
>  err_put_regulator:
> -       regulator_put(ts->reg);
> - err_free_gpio:
> +       if (ts->reg)
> +               regulator_put(ts->reg);
> +#endif
>        if (ts->gpio_pendown != -1)
>                gpio_free(ts->gpio_pendown);
>  err_cleanup_filter:
> @@ -1251,8 +1263,12 @@ static int __devexit ads7846_remove(struct spi_device *spi)
>        /* suspend left the IRQ disabled */
>        enable_irq(ts->spi->irq);
>
> -       regulator_disable(ts->reg);
> -       regulator_put(ts->reg);
> +#ifdef CONFIG_REGULATOR

Skip the #ifdef.

> +       if (ts->reg) {
> +               regulator_disable(ts->reg);
> +               regulator_put(ts->reg);
> +       }
> +#endif
>
>        if (ts->gpio_pendown != -1)
>                gpio_free(ts->gpio_pendown);
> --
> 1.7.1

Yours,
Linus Walleij