[PATCH v4 1/4] omap4 hsmmc: Adding card detect support for MMC1
kishore kadiyala
kishorek.kadiyala at gmail.com
Fri Oct 1 08:02:11 EDT 2010
Samuel,
Sorry , I will ensure to CC you for MFD related changes in future.
Regards,
Kishore
On Fri, Oct 1, 2010 at 4:59 PM, Samuel Ortiz <sameo at linux.intel.com> wrote:
> On Fri, Oct 01, 2010 at 12:29:48PM +0530, kishore kadiyala wrote:
>> Ping !!
> Applied !!
>
> BTW, please add the full patch when you cc me, so that I don't have to dig
> through patchwork to grab something I can git-am.
>
> Cheers,
> Samuel.
>
>
>> On Wed, Sep 29, 2010 at 4:11 PM, kishore kadiyala
>> <kishorek.kadiyala at gmail.com> wrote:
>> > Gentle Reminder !
>> >
>> > Regards,
>> > Kishore
>> >
>> > On Tue, Sep 28, 2010 at 12:22 PM, kishore kadiyala
>> > <kishorek.kadiyala at gmail.com> wrote:
>> >> Hi Samuel,
>> >>
>> >> Could you please review this patch which touches mfd/twl6030-irq.c for
>> >> card detect support
>> >> of MMC1 controller on OMAP4.
>> >>
>> >> Regards,
>> >> Kishore
>> >>
>> >> On Mon, Sep 27, 2010 at 1:25 PM, kishore kadiyala
>> >> <kishorek.kadiyala at gmail.com> wrote:
>> >>> Cc: Samuel Ortiz <sameo at linux.intel.com>
>> >>>
>> >>> On Fri, Sep 24, 2010 at 10:43 PM, kishore kadiyala
>> >>> <kishore.kadiyala at ti.com> wrote:
>> >>>> Adding card detect callback function and card detect configuration
>> >>>> function for MMC1 Controller on OMAP4.
>> >>>>
>> >>>> Card detect configuration function does initial configuration of the
>> >>>> MMC Control & PullUp-PullDown registers of Phoenix.
>> >>>>
>> >>>> For MMC1 Controller, card detect interrupt source is
>> >>>> twl6030 which is non-gpio. The card detect call back function provides
>> >>>> card present/absent status by reading MMC Control register present
>> >>>> on twl6030.
>> >>>>
>> >>>> Since OMAP4 doesn't use any GPIO line as used in OMAP3 for card detect,
>> >>>> the suspend/resume initialization which was done in omap_hsmmc_gpio_init
>> >>>> previously is moved to the probe thus making it generic for both OMAP3 & OMAP4.
>> >>>>
>> >>>> Cc: Tony Lindgren <tony at atomide.com>
>> >>>> Cc: Andrew Morton <akpm at linux-foundation.org>
>> >>>> Cc: Madhusudhan Chikkature <madhu.cr at ti.com>
>> >>>> Cc: Adrian Hunter <adrian.hunter at nokia.com>
>> >>>> Signed-off-by: Kishore Kadiyala <kishore.kadiyala at ti.com>
>> >>>> ---
>> >>>> arch/arm/mach-omap2/board-4430sdp.c | 7 +++-
>> >>>> drivers/mfd/twl6030-irq.c | 73 +++++++++++++++++++++++++++++++++++
>> >>>> drivers/mmc/host/omap_hsmmc.c | 4 +-
>> >>>> include/linux/i2c/twl.h | 31 +++++++++++++++
>> >>>> 4 files changed, 112 insertions(+), 3 deletions(-)
>> >>>>
>> >>>> diff --git a/arch/arm/mach-omap2/board-4430sdp.c b/arch/arm/mach-omap2/board-4430sdp.c
>> >>>> index 9447644..a49f285 100644
>> >>>> --- a/arch/arm/mach-omap2/board-4430sdp.c
>> >>>> +++ b/arch/arm/mach-omap2/board-4430sdp.c
>> >>>> @@ -227,9 +227,14 @@ static int omap4_twl6030_hsmmc_late_init(struct device *dev)
>> >>>> struct omap_mmc_platform_data *pdata = dev->platform_data;
>> >>>>
>> >>>> /* Setting MMC1 Card detect Irq */
>> >>>> - if (pdev->id == 0)
>> >>>> + if (pdev->id == 0) {
>> >>>> + ret = twl6030_mmc_card_detect_config();
>> >>>> + if (ret)
>> >>>> + pr_err("Failed configuring MMC1 card detect\n");
>> >>>> pdata->slots[0].card_detect_irq = TWL6030_IRQ_BASE +
>> >>>> MMCDETECT_INTR_OFFSET;
>> >>>> + pdata->slots[0].card_detect = twl6030_mmc_card_detect;
>> >>>> + }
>> >>>> return ret;
>> >>>> }
>> >>>>
>> >>>> diff --git a/drivers/mfd/twl6030-irq.c b/drivers/mfd/twl6030-irq.c
>> >>>> index 10bf228..2d3bb82 100644
>> >>>> --- a/drivers/mfd/twl6030-irq.c
>> >>>> +++ b/drivers/mfd/twl6030-irq.c
>> >>>> @@ -36,6 +36,7 @@
>> >>>> #include <linux/irq.h>
>> >>>> #include <linux/kthread.h>
>> >>>> #include <linux/i2c/twl.h>
>> >>>> +#include <linux/platform_device.h>
>> >>>>
>> >>>> /*
>> >>>> * TWL6030 (unlike its predecessors, which had two level interrupt handling)
>> >>>> @@ -223,6 +224,78 @@ int twl6030_interrupt_mask(u8 bit_mask, u8 offset)
>> >>>> }
>> >>>> EXPORT_SYMBOL(twl6030_interrupt_mask);
>> >>>>
>> >>>> +int twl6030_mmc_card_detect_config(void)
>> >>>> +{
>> >>>> + int ret;
>> >>>> + u8 reg_val = 0;
>> >>>> +
>> >>>> + /* Unmasking the Card detect Interrupt line for MMC1 from Phoenix */
>> >>>> + twl6030_interrupt_unmask(TWL6030_MMCDETECT_INT_MASK,
>> >>>> + REG_INT_MSK_LINE_B);
>> >>>> + twl6030_interrupt_unmask(TWL6030_MMCDETECT_INT_MASK,
>> >>>> + REG_INT_MSK_STS_B);
>> >>>> + /*
>> >>>> + * Intially Configuring MMC_CTRL for receving interrupts &
>> >>>> + * Card status on TWL6030 for MMC1
>> >>>> + */
>> >>>> + ret = twl_i2c_read_u8(TWL6030_MODULE_ID0, ®_val, TWL6030_MMCCTRL);
>> >>>> + if (ret < 0) {
>> >>>> + pr_err("twl6030: Failed to read MMCCTRL, error %d\n", ret);
>> >>>> + return ret;
>> >>>> + }
>> >>>> + reg_val &= ~VMMC_AUTO_OFF;
>> >>>> + reg_val |= SW_FC;
>> >>>> + ret = twl_i2c_write_u8(TWL6030_MODULE_ID0, reg_val, TWL6030_MMCCTRL);
>> >>>> + if (ret < 0) {
>> >>>> + pr_err("twl6030: Failed to write MMCCTRL, error %d\n", ret);
>> >>>> + return ret;
>> >>>> + }
>> >>>> +
>> >>>> + /* Configuring PullUp-PullDown register */
>> >>>> + ret = twl_i2c_read_u8(TWL6030_MODULE_ID0, ®_val,
>> >>>> + TWL6030_CFG_INPUT_PUPD3);
>> >>>> + if (ret < 0) {
>> >>>> + pr_err("twl6030: Failed to read CFG_INPUT_PUPD3, error %d\n",
>> >>>> + ret);
>> >>>> + return ret;
>> >>>> + }
>> >>>> + reg_val &= ~(MMC_PU | MMC_PD);
>> >>>> + ret = twl_i2c_write_u8(TWL6030_MODULE_ID0, reg_val,
>> >>>> + TWL6030_CFG_INPUT_PUPD3);
>> >>>> + if (ret < 0) {
>> >>>> + pr_err("twl6030: Failed to write CFG_INPUT_PUPD3, error %d\n",
>> >>>> + ret);
>> >>>> + return ret;
>> >>>> + }
>> >>>> + return 0;
>> >>>> +}
>> >>>> +EXPORT_SYMBOL(twl6030_mmc_card_detect_config);
>> >>>> +
>> >>>> +int twl6030_mmc_card_detect(struct device *dev, int slot)
>> >>>> +{
>> >>>> + int ret = -EIO;
>> >>>> + u8 read_reg = 0;
>> >>>> + struct platform_device *pdev = to_platform_device(dev);
>> >>>> +
>> >>>> + if (pdev->id) {
>> >>>> + /* TWL6030 provide's Card detect support for
>> >>>> + * only MMC1 controller.
>> >>>> + */
>> >>>> + pr_err("Unkown MMC controller %d in %s\n", pdev->id, __func__);
>> >>>> + return ret;
>> >>>> + }
>> >>>> + /*
>> >>>> + * BIT0 of MMC_CTRL on TWL6030 provides card status for MMC1
>> >>>> + * 0 - Card not present ,1 - Card present
>> >>>> + */
>> >>>> + ret = twl_i2c_read_u8(TWL6030_MODULE_ID0, &read_reg,
>> >>>> + TWL6030_MMCCTRL);
>> >>>> + if (ret >= 0)
>> >>>> + ret = read_reg & STS_MMC;
>> >>>> + return ret;
>> >>>> +}
>> >>>> +EXPORT_SYMBOL(twl6030_mmc_card_detect);
>> >>>> +
>> >>>> int twl6030_init_irq(int irq_num, unsigned irq_base, unsigned irq_end)
>> >>>> {
>> >>>>
>> >>>> diff --git a/drivers/mmc/host/omap_hsmmc.c b/drivers/mmc/host/omap_hsmmc.c
>> >>>> index 562dbbb..a51894d 100644
>> >>>> --- a/drivers/mmc/host/omap_hsmmc.c
>> >>>> +++ b/drivers/mmc/host/omap_hsmmc.c
>> >>>> @@ -466,8 +466,6 @@ static int omap_hsmmc_gpio_init(struct omap_mmc_platform_data *pdata)
>> >>>> int ret;
>> >>>>
>> >>>> if (gpio_is_valid(pdata->slots[0].switch_pin)) {
>> >>>> - pdata->suspend = omap_hsmmc_suspend_cdirq;
>> >>>> - pdata->resume = omap_hsmmc_resume_cdirq;
>> >>>> if (pdata->slots[0].cover)
>> >>>> pdata->slots[0].get_cover_state =
>> >>>> omap_hsmmc_get_cover_state;
>> >>>> @@ -2211,6 +2209,8 @@ static int __init omap_hsmmc_probe(struct platform_device *pdev)
>> >>>> "Unable to grab MMC CD IRQ\n");
>> >>>> goto err_irq_cd;
>> >>>> }
>> >>>> + pdata->suspend = omap_hsmmc_suspend_cdirq;
>> >>>> + pdata->resume = omap_hsmmc_resume_cdirq;
>> >>>> }
>> >>>>
>> >>>> omap_hsmmc_disable_irq(host);
>> >>>> diff --git a/include/linux/i2c/twl.h b/include/linux/i2c/twl.h
>> >>>> index 6de90bf..e64894c 100644
>> >>>> --- a/include/linux/i2c/twl.h
>> >>>> +++ b/include/linux/i2c/twl.h
>> >>>> @@ -141,6 +141,16 @@
>> >>>> #define TWL6030_CHARGER_CTRL_INT_MASK 0x10
>> >>>> #define TWL6030_CHARGER_FAULT_INT_MASK 0x60
>> >>>>
>> >>>> +#define TWL6030_MMCCTRL 0xEE
>> >>>> +#define VMMC_AUTO_OFF (0x1 << 3)
>> >>>> +#define SW_FC (0x1 << 2)
>> >>>> +#define STS_MMC 0x1
>> >>>> +
>> >>>> +#define TWL6030_CFG_INPUT_PUPD3 0xF2
>> >>>> +#define MMC_PU (0x1 << 3)
>> >>>> +#define MMC_PD (0x1 << 2)
>> >>>> +
>> >>>> +
>> >>>>
>> >>>> #define TWL4030_CLASS_ID 0x4030
>> >>>> #define TWL6030_CLASS_ID 0x6030
>> >>>> @@ -173,6 +183,27 @@ int twl_i2c_read(u8 mod_no, u8 *value, u8 reg, unsigned num_bytes);
>> >>>> int twl6030_interrupt_unmask(u8 bit_mask, u8 offset);
>> >>>> int twl6030_interrupt_mask(u8 bit_mask, u8 offset);
>> >>>>
>> >>>> +/* Card detect Configuration for MMC1 Controller on OMAP4 */
>> >>>> +#ifdef CONFIG_TWL4030_CORE
>> >>>> +int twl6030_mmc_card_detect_config(void);
>> >>>> +#else
>> >>>> +static inline int twl6030_mmc_card_detect_config(void)
>> >>>> +{
>> >>>> + pr_debug("twl6030_mmc_card_detect_config not supported\n");
>> >>>> + return 0;
>> >>>> +}
>> >>>> +#endif
>> >>>> +
>> >>>> +/* MMC1 Controller on OMAP4 uses Phoenix irq for Card detect */
>> >>>> +#ifdef CONFIG_TWL4030_CORE
>> >>>> +int twl6030_mmc_card_detect(struct device *dev, int slot);
>> >>>> +#else
>> >>>> +static inline int twl6030_mmc_card_detect(struct device *dev, int slot)
>> >>>> +{
>> >>>> + pr_debug("Call back twl6030_mmc_card_detect not supported\n");
>> >>>> + return -EIO;
>> >>>> +}
>> >>>> +#endif
>> >>>> /*----------------------------------------------------------------------*/
>> >>>>
>> >>>> /*
>> >>>> --
>> >>>> 1.7.0.4
>> >>>>
>> >>>>
>> >>>> --
>> >>>> To unsubscribe from this list: send the line "unsubscribe linux-mmc" in
>> >>>> the body of a message to majordomo at vger.kernel.org
>> >>>> More majordomo info at http://vger.kernel.org/majordomo-info.html
>> >>>>
>> >>>
>> >>
>> >
>
> --
> Intel Open Source Technology Centre
> http://oss.intel.com/
>
More information about the linux-arm-kernel
mailing list