[PATCH 3/3] ARM: S5PV210: Add voltage consumer of WM8994 to the regulator framework
Chanwoo Choi
cw00.choi at samsung.com
Fri Oct 1 00:23:25 EDT 2010
This patch add cose related to regulator. To control powre consumeption
have registered the voltage consumer of WM8994 to the regulator framework.
Additionally, I explain the constraints of the regulator of WM8994 codec.
All these consumer supply of WM8994 codec connected the regulator(VCC_1.8V)
on a circuit diagram. "VCC_1.8V" regulator is always enabled, because it is
used to many devices on Goni/Aquila board. This is required especially
when there are many devices physically attached to "VCC_1.8V" and some of
they did not "register" as consumers to "VCC_1.8V". "VCC_1.8V" might be
turned off by those who are registered while "unregistered" are still active
Signed-off-by : Chanwoo Choi <cw00.choi at samsung.com>
Signed-off-by : Joonyoung Shim <jy0922.shim at samsung.com>
Signed-off-by : Kyungmin Park <kyungmin.park at samsung.com>
---
arch/arm/mach-s5pv210/mach-aquila.c | 119 +++++++++++++++++++++++++++++++++++
arch/arm/mach-s5pv210/mach-goni.c | 119 +++++++++++++++++++++++++++++++++++
2 files changed, 238 insertions(+), 0 deletions(-)
diff --git a/arch/arm/mach-s5pv210/mach-aquila.c b/arch/arm/mach-s5pv210/mach-aquila.c
index 92dad41..825d70c 100644
--- a/arch/arm/mach-s5pv210/mach-aquila.c
+++ b/arch/arm/mach-s5pv210/mach-aquila.c
@@ -16,6 +16,8 @@
#include <linux/i2c.h>
#include <linux/i2c-gpio.h>
#include <linux/mfd/max8998.h>
+#include <linux/mfd/wm8994/pdata.h>
+#include <linux/regulator/fixed.h>
#include <linux/gpio_keys.h>
#include <linux/input.h>
#include <linux/gpio.h>
@@ -379,6 +381,120 @@ static struct max8998_platform_data aquila_max8998_pdata = {
};
#endif
+static struct regulator_consumer_supply wm8994_fixed_voltage0_supplies[] = {
+ {
+ .dev_name = "5-001a",
+ .supply = "DBVDD",
+ }, {
+ .dev_name = "5-001a",
+ .supply = "AVDD2",
+ }, {
+ .dev_name = "5-001a",
+ .supply = "CPVDD",
+ },
+
+};
+
+static struct regulator_consumer_supply wm8994_fixed_voltage1_supplies[] = {
+ {
+ .dev_name = "5-001a",
+ .supply = "SPKVDD1",
+ }, {
+ .dev_name = "5-001a",
+ .supply = "SPKVDD2",
+ },
+};
+
+static struct regulator_init_data wm8994_fixed_voltage0_init_data = {
+ .constraints = {
+ .always_on = 1,
+ },
+ .num_consumer_supplies = ARRAY_SIZE(wm8994_fixed_voltage0_supplies),
+ .consumer_supplies = wm8994_fixed_voltage0_supplies,
+};
+
+static struct regulator_init_data wm8994_fixed_voltage1_init_data = {
+ .constraints = {
+ .always_on = 1,
+ },
+ .num_consumer_supplies = ARRAY_SIZE(wm8994_fixed_voltage1_supplies),
+ .consumer_supplies = wm8994_fixed_voltage1_supplies,
+};
+
+static struct fixed_voltage_config wm8994_fixed_voltage0_config = {
+ .supply_name = "VCC_1.8V_PDA",
+ .microvolts = 1800000,
+ .gpio = -EINVAL,
+ .init_data = &wm8994_fixed_voltage0_init_data,
+};
+
+static struct fixed_voltage_config wm8994_fixed_voltage1_config = {
+ .supply_name = "V_BAT",
+ .microvolts = 3700000,
+ .gpio = -EINVAL,
+ .init_data = &wm8994_fixed_voltage1_init_data,
+};
+
+static struct platform_device wm8994_fixed_voltage0 = {
+ .name = "reg-fixed-voltage",
+ .id = 0,
+ .dev = {
+ .platform_data = &wm8994_fixed_voltage0_config,
+ },
+};
+
+static struct platform_device wm8994_fixed_voltage1 = {
+ .name = "reg-fixed-voltage",
+ .id = 1,
+ .dev = {
+ .platform_data = &wm8994_fixed_voltage1_config,
+ },
+};
+
+static struct regulator_consumer_supply wm8994_avdd1_supply = {
+ .dev_name = "5-001a",
+ .supply = "AVDD1",
+};
+
+static struct regulator_consumer_supply wm8994_dcvdd_supply = {
+ .dev_name = "5-001a",
+ .supply = "DCVDD",
+};
+
+static struct regulator_init_data wm8994_ldo1_data = {
+ .constraints = {
+ .name = "AVDD1_3.0V",
+ .valid_ops_mask = REGULATOR_CHANGE_STATUS,
+ },
+ .num_consumer_supplies = 1,
+ .consumer_supplies = &wm8994_avdd1_supply,
+};
+
+static struct regulator_init_data wm8994_ldo2_data = {
+ .constraints = {
+ .name = "DCVDD_1.0V",
+ },
+ .num_consumer_supplies = 1,
+ .consumer_supplies = &wm8994_dcvdd_supply,
+};
+
+static struct wm8994_pdata wm8994_platform_data = {
+ /* configure gpio1 function: 0x0001(Logic level input/output) */
+ .gpio_defaults[0] = 0x0001,
+ /* configure gpio3/4/5/7 function for AIF2 voice */
+ .gpio_defaults[2] = 0x8100,
+ .gpio_defaults[3] = 0x8100,
+ .gpio_defaults[4] = 0x8100,
+ .gpio_defaults[6] = 0x0100,
+ /* configure gpio8/9/10/11 function for AIF3 BT */
+ .gpio_defaults[7] = 0x8100,
+ .gpio_defaults[8] = 0x0100,
+ .gpio_defaults[9] = 0x0100,
+ .gpio_defaults[10] = 0x0100,
+ .ldo[0] = { S5PV210_MP03(6), NULL, &wm8994_ldo1_data }, /* XM0FRNB_2 */
+ .ldo[1] = { 0, NULL, &wm8994_ldo2_data },
+};
+
/* GPIO I2C PMIC */
#define AP_I2C_GPIO_PMIC_BUS_4 4
static struct i2c_gpio_platform_data aquila_i2c_gpio_pmic_data = {
@@ -423,6 +539,7 @@ static struct i2c_board_info i2c_gpio5_devs[] __initdata = {
{
/* CS/ADDR = low 0x34 (FYI: high = 0x36) */
I2C_BOARD_INFO("wm8994", 0x1a),
+ .platform_data = &wm8994_platform_data,
},
};
@@ -508,6 +625,8 @@ static struct platform_device *aquila_devices[] __initdata = {
&s5p_device_fimc1,
&s5p_device_fimc2,
&s5pv210_device_iis0,
+ &wm8994_fixed_voltage0,
+ &wm8994_fixed_voltage1,
};
static void __init aquila_sound_init(void)
diff --git a/arch/arm/mach-s5pv210/mach-goni.c b/arch/arm/mach-s5pv210/mach-goni.c
index d3bab85..667d453 100644
--- a/arch/arm/mach-s5pv210/mach-goni.c
+++ b/arch/arm/mach-s5pv210/mach-goni.c
@@ -16,6 +16,8 @@
#include <linux/i2c.h>
#include <linux/i2c-gpio.h>
#include <linux/mfd/max8998.h>
+#include <linux/mfd/wm8994/pdata.h>
+#include <linux/regulator/fixed.h>
#include <linux/gpio_keys.h>
#include <linux/input.h>
#include <linux/gpio.h>
@@ -360,6 +362,120 @@ static struct max8998_platform_data goni_max8998_pdata = {
};
#endif
+static struct regulator_consumer_supply wm8994_fixed_voltage0_supplies[] = {
+ {
+ .dev_name = "5-001a",
+ .supply = "DBVDD",
+ }, {
+ .dev_name = "5-001a",
+ .supply = "AVDD2",
+ }, {
+ .dev_name = "5-001a",
+ .supply = "CPVDD",
+ },
+
+};
+
+static struct regulator_consumer_supply wm8994_fixed_voltage1_supplies[] = {
+ {
+ .dev_name = "5-001a",
+ .supply = "SPKVDD1",
+ }, {
+ .dev_name = "5-001a",
+ .supply = "SPKVDD2",
+ },
+};
+
+static struct regulator_init_data wm8994_fixed_voltage0_init_data = {
+ .constraints = {
+ .always_on = 1,
+ },
+ .num_consumer_supplies = ARRAY_SIZE(wm8994_fixed_voltage0_supplies),
+ .consumer_supplies = wm8994_fixed_voltage0_supplies,
+};
+
+static struct regulator_init_data wm8994_fixed_voltage1_init_data = {
+ .constraints = {
+ .always_on = 1,
+ },
+ .num_consumer_supplies = ARRAY_SIZE(wm8994_fixed_voltage1_supplies),
+ .consumer_supplies = wm8994_fixed_voltage1_supplies,
+};
+
+static struct fixed_voltage_config wm8994_fixed_voltage0_config = {
+ .supply_name = "VCC_1.8V_PDA",
+ .microvolts = 1800000,
+ .gpio = -EINVAL,
+ .init_data = &wm8994_fixed_voltage0_init_data,
+};
+
+static struct fixed_voltage_config wm8994_fixed_voltage1_config = {
+ .supply_name = "V_BAT",
+ .microvolts = 3700000,
+ .gpio = -EINVAL,
+ .init_data = &wm8994_fixed_voltage1_init_data,
+};
+
+static struct platform_device wm8994_fixed_voltage0 = {
+ .name = "reg-fixed-voltage",
+ .id = 0,
+ .dev = {
+ .platform_data = &wm8994_fixed_voltage0_config,
+ },
+};
+
+static struct platform_device wm8994_fixed_voltage1 = {
+ .name = "reg-fixed-voltage",
+ .id = 1,
+ .dev = {
+ .platform_data = &wm8994_fixed_voltage1_config,
+ },
+};
+
+static struct regulator_consumer_supply wm8994_avdd1_supply = {
+ .dev_name = "5-001a",
+ .supply = "AVDD1",
+};
+
+static struct regulator_consumer_supply wm8994_dcvdd_supply = {
+ .dev_name = "5-001a",
+ .supply = "DCVDD",
+};
+
+static struct regulator_init_data wm8994_ldo1_data = {
+ .constraints = {
+ .name = "AVDD1_3.0V",
+ .valid_ops_mask = REGULATOR_CHANGE_STATUS,
+ },
+ .num_consumer_supplies = 1,
+ .consumer_supplies = &wm8994_avdd1_supply,
+};
+
+static struct regulator_init_data wm8994_ldo2_data = {
+ .constraints = {
+ .name = "DCVDD_1.0V",
+ },
+ .num_consumer_supplies = 1,
+ .consumer_supplies = &wm8994_dcvdd_supply,
+};
+
+static struct wm8994_pdata wm8994_platform_data = {
+ /* configure gpio1 function: 0x0001(Logic level input/output) */
+ .gpio_defaults[0] = 0x0001,
+ /* configure gpio3/4/5/7 function for AIF2 voice */
+ .gpio_defaults[2] = 0x8100,
+ .gpio_defaults[3] = 0x8100,
+ .gpio_defaults[4] = 0x8100,
+ .gpio_defaults[6] = 0x0100,
+ /* configure gpio8/9/10/11 function for AIF3 BT */
+ .gpio_defaults[7] = 0x8100,
+ .gpio_defaults[8] = 0x0100,
+ .gpio_defaults[9] = 0x0100,
+ .gpio_defaults[10] = 0x0100,
+ .ldo[0] = { S5PV210_MP03(6), NULL, &wm8994_ldo1_data }, /* XM0FRNB_2 */
+ .ldo[1] = { 0, NULL, &wm8994_ldo2_data },
+};
+
/* GPIO I2C PMIC */
#define AP_I2C_GPIO_PMIC_BUS_4 4
static struct i2c_gpio_platform_data goni_i2c_gpio_pmic_data = {
@@ -404,6 +520,7 @@ static struct i2c_board_info i2c_gpio5_devs[] __initdata = {
{
/* CS/ADDR = low 0x34 (FYI: high = 0x36) */
I2C_BOARD_INFO("wm8994", 0x1a),
+ .platform_data = &wm8994_platform_data,
},
};
@@ -489,6 +606,8 @@ static struct platform_device *goni_devices[] __initdata = {
&s3c_device_hsmmc1,
&s3c_device_hsmmc2,
&s5pv210_device_iis0,
+ &wm8994_fixed_voltage0,
+ &wm8994_fixed_voltage1,
};
static void __init goni_sound_init(void)
--
1.7.0.4
More information about the linux-arm-kernel
mailing list