[PATCH] Kirkwood: Add support for 6282 based QNAP devices

[Martin Michlmayr]

Add support for the QNAP NAS devices based on Marvell's 6282 Kirkwood
chip (TS-119P+, TS-219P+ and TS-419P+).  The differences to the 6281
based devices are:
 - Ethernet PHY address
 - GPIOs used for buttons (TS-119P+/TS-219P+)

Signed-off-by: Martin Michlmayr <tbm at cyrius.com>

--- a/arch/arm/mach-kirkwood/Kconfig
+++ b/arch/arm/mach-kirkwood/Kconfig
@@ -48,15 +48,15 @@ config MACH_TS219
 	bool "QNAP TS-110, TS-119, TS-210, TS-219 and TS-219P Turbo NAS"
 	help
 	  Say 'Y' here if you want your kernel to support the
-	  QNAP TS-110, TS-119, TS-210, TS-219 and TS-219P Turbo NAS
-	  devices.
+	  QNAP TS-110, TS-119, TS-119P+, TS-210, TS-219, TS-219P and
+	  TS-219P+ Turbo NAS devices.
 
 config MACH_TS41X
 	bool "QNAP TS-410, TS-410U, TS-419P and TS-419U Turbo NAS"
 	help
 	  Say 'Y' here if you want your kernel to support the
-	  QNAP TS-410, TS-410U, TS-419P and TS-419U Turbo NAS
-	  devices.
+	  QNAP TS-410, TS-410U, TS-419P, TS-419P+ and TS-419U Turbo
+	  NAS devices.
 
 config MACH_DOCKSTAR
 	bool "Seagate FreeAgent DockStar"
diff --git a/arch/arm/mach-kirkwood/ts219-setup.c b/arch/arm/mach-kirkwood/ts219-setup.c
index 6710bd7..dc999c4 100644
--- a/arch/arm/mach-kirkwood/ts219-setup.c
+++ b/arch/arm/mach-kirkwood/ts219-setup.c
@@ -80,15 +80,19 @@ static unsigned int qnap_ts219_mpp_config[] __initdata = {
 	MPP11_UART0_RXD,
 	MPP13_UART1_TXD,	/* PIC controller */
 	MPP14_UART1_RXD,	/* PIC controller */
-	MPP15_GPIO,		/* USB Copy button */
-	MPP16_GPIO,		/* Reset button */
+	MPP15_GPIO,		/* USB Copy button (on devices with 88F6281) */
+	MPP16_GPIO,		/* Reset button (on devices with 88F6281) */
 	MPP36_GPIO,		/* RAM: 0: 256 MB, 1: 512 MB */
+	MPP37_GPIO,		/* Reset button (on devices with 88F6282) */
+	MPP43_GPIO,		/* USB Copy button (on devices with 88F6282) */
 	MPP44_GPIO,		/* Board ID: 0: TS-11x, 1: TS-21x */
 	0
 };
 
 static void __init qnap_ts219_init(void)
 {
+	u32 dev, rev;
+
 	/*
 	 * Basic setup. Needs to be called early.
 	 */
@@ -100,6 +104,14 @@ static void __init qnap_ts219_init(void)
 	qnap_tsx1x_register_flash();
 	kirkwood_i2c_init();
 	i2c_register_board_info(0, &qnap_ts219_i2c_rtc, 1);
+
+	kirkwood_pcie_id(&dev, &rev);
+	if (dev == MV88F6282_DEV_ID) {
+		qnap_ts219_buttons[0].gpio = 43; /* USB Copy button */
+		qnap_ts219_buttons[1].gpio = 37; /* Reset button */
+		qnap_ts219_ge00_data.phy_addr = MV643XX_ETH_PHY_ADDR(0);
+	}
+
 	kirkwood_ge00_init(&qnap_ts219_ge00_data);
 	kirkwood_sata_init(&qnap_ts219_sata_data);
 	kirkwood_ehci_init();
diff --git a/arch/arm/mach-kirkwood/ts41x-setup.c b/arch/arm/mach-kirkwood/ts41x-setup.c
index 3587a28..9a44029 100644
--- a/arch/arm/mach-kirkwood/ts41x-setup.c
+++ b/arch/arm/mach-kirkwood/ts41x-setup.c
@@ -119,6 +119,8 @@ static unsigned int qnap_ts41x_mpp_config[] __initdata = {
 
 static void __init qnap_ts41x_init(void)
 {
+	u32 dev, rev;
+
 	/*
 	 * Basic setup. Needs to be called early.
 	 */
@@ -130,8 +132,15 @@ static void __init qnap_ts41x_init(void)
 	qnap_tsx1x_register_flash();
 	kirkwood_i2c_init();
 	i2c_register_board_info(0, &qnap_ts41x_i2c_rtc, 1);
+
+	kirkwood_pcie_id(&dev, &rev);
+	if (dev == MV88F6282_DEV_ID) {
+		qnap_ts41x_ge00_data.phy_addr = MV643XX_ETH_PHY_ADDR(0);
+		qnap_ts41x_ge01_data.phy_addr = MV643XX_ETH_PHY_ADDR(1);
+	}
 	kirkwood_ge00_init(&qnap_ts41x_ge00_data);
 	kirkwood_ge01_init(&qnap_ts41x_ge01_data);
+
 	kirkwood_sata_init(&qnap_ts41x_sata_data);
 	kirkwood_ehci_init();
 	platform_device_register(&qnap_ts41x_button_device);

-- 
Martin Michlmayr
http://www.cyrius.com/