[PATCH 1/6] at91: Convert remaining boards to new-style UART initialization
Jean-Christophe PLAGNIOL-VILLARD
plagnioj at jcrosoft.com
Sat Nov 20 05:08:48 EST 2010
Convert the following AT91RM9200-based boards to the new-style UART
initialization:
- Ajeco 1ARM Single Board Computer
- Sperry-Sun KAFA board
- picotux 200
Remove the deprecated at91_init_serial
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj at jcrosoft.com>
---
arch/arm/mach-at91/at91rm9200_devices.c | 45 -------------------------------
arch/arm/mach-at91/board-1arm.c | 26 +++++++++---------
arch/arm/mach-at91/board-kafa.c | 21 +++++---------
arch/arm/mach-at91/board-picotux200.c | 23 +++++++---------
arch/arm/mach-at91/include/mach/board.h | 6 ----
5 files changed, 31 insertions(+), 90 deletions(-)
diff --git a/arch/arm/mach-at91/at91rm9200_devices.c b/arch/arm/mach-at91/at91rm9200_devices.c
index 9338825..7b53922 100644
--- a/arch/arm/mach-at91/at91rm9200_devices.c
+++ b/arch/arm/mach-at91/at91rm9200_devices.c
@@ -1106,51 +1106,6 @@ static inline void configure_usart3_pins(unsigned pins)
static struct platform_device *__initdata at91_uarts[ATMEL_MAX_UART]; /* the UARTs to use */
struct platform_device *atmel_default_console_device; /* the serial console device */
-void __init __deprecated at91_init_serial(struct at91_uart_config *config)
-{
- int i;
-
- /* Fill in list of supported UARTs */
- for (i = 0; i < config->nr_tty; i++) {
- switch (config->tty_map[i]) {
- case 0:
- configure_usart0_pins(ATMEL_UART_CTS | ATMEL_UART_RTS);
- at91_uarts[i] = &at91rm9200_uart0_device;
- at91_clock_associate("usart0_clk", &at91rm9200_uart0_device.dev, "usart");
- break;
- case 1:
- configure_usart1_pins(ATMEL_UART_CTS | ATMEL_UART_RTS | ATMEL_UART_DSR | ATMEL_UART_DTR | ATMEL_UART_DCD | ATMEL_UART_RI);
- at91_uarts[i] = &at91rm9200_uart1_device;
- at91_clock_associate("usart1_clk", &at91rm9200_uart1_device.dev, "usart");
- break;
- case 2:
- configure_usart2_pins(0);
- at91_uarts[i] = &at91rm9200_uart2_device;
- at91_clock_associate("usart2_clk", &at91rm9200_uart2_device.dev, "usart");
- break;
- case 3:
- configure_usart3_pins(0);
- at91_uarts[i] = &at91rm9200_uart3_device;
- at91_clock_associate("usart3_clk", &at91rm9200_uart3_device.dev, "usart");
- break;
- case 4:
- configure_dbgu_pins();
- at91_uarts[i] = &at91rm9200_dbgu_device;
- at91_clock_associate("mck", &at91rm9200_dbgu_device.dev, "usart");
- break;
- default:
- continue;
- }
- at91_uarts[i]->id = i; /* update ID number to mapped ID */
- }
-
- /* Set serial console device */
- if (config->console_tty < ATMEL_MAX_UART)
- atmel_default_console_device = at91_uarts[config->console_tty];
- if (!atmel_default_console_device)
- printk(KERN_INFO "AT91: No default serial console defined.\n");
-}
-
void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins)
{
struct platform_device *pdev;
diff --git a/arch/arm/mach-at91/board-1arm.c b/arch/arm/mach-at91/board-1arm.c
index 46bdc82..8a3fc84 100644
--- a/arch/arm/mach-at91/board-1arm.c
+++ b/arch/arm/mach-at91/board-1arm.c
@@ -39,24 +39,24 @@
#include "generic.h"
-/*
- * Serial port configuration.
- * 0 .. 3 = USART0 .. USART3
- * 4 = DBGU
- */
-static struct at91_uart_config __initdata onearm_uart_config = {
- .console_tty = 0, /* ttyS0 */
- .nr_tty = 3,
- .tty_map = { 4, 0, 1, -1, -1 }, /* ttyS0, ..., ttyS4 */
-};
-
static void __init onearm_map_io(void)
{
/* Initialize processor: 18.432 MHz crystal */
at91rm9200_initialize(18432000, AT91RM9200_PQFP);
- /* Setup the serial ports and console */
- at91_init_serial(&onearm_uart_config);
+ /* DBGU on ttyS0. (Rx & Tx only) */
+ at91_register_uart(0, 0, 0);
+
+ /* USART0 on ttyS1 (Rx, Tx, CTS, RTS) */
+ at91_register_uart(AT91RM9200_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS);
+
+ /* USART1 on ttyS2 (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
+ at91_register_uart(AT91RM9200_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS
+ | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
+ | ATMEL_UART_RI);
+
+ /* set serial console to ttyS0 (ie, DBGU) */
+ at91_set_serial_console(0);
}
static void __init onearm_init_irq(void)
diff --git a/arch/arm/mach-at91/board-kafa.c b/arch/arm/mach-at91/board-kafa.c
index c0ce79d..d2e1f4e 100644
--- a/arch/arm/mach-at91/board-kafa.c
+++ b/arch/arm/mach-at91/board-kafa.c
@@ -39,17 +39,6 @@
#include "generic.h"
-/*
- * Serial port configuration.
- * 0 .. 3 = USART0 .. USART3
- * 4 = DBGU
- */
-static struct at91_uart_config __initdata kafa_uart_config = {
- .console_tty = 0, /* ttyS0 */
- .nr_tty = 2,
- .tty_map = { 4, 0, -1, -1, -1 } /* ttyS0, ..., ttyS4 */
-};
-
static void __init kafa_map_io(void)
{
/* Initialize processor: 18.432 MHz crystal */
@@ -58,8 +47,14 @@ static void __init kafa_map_io(void)
/* Set up the LEDs */
at91_init_leds(AT91_PIN_PB4, AT91_PIN_PB4);
- /* Setup the serial ports and console */
- at91_init_serial(&kafa_uart_config);
+ /* DBGU on ttyS0. (Rx & Tx only) */
+ at91_register_uart(0, 0, 0);
+
+ /* USART0 on ttyS1 (Rx, Tx, CTS, RTS) */
+ at91_register_uart(AT91RM9200_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS);
+
+ /* set serial console to ttyS0 (ie, DBGU) */
+ at91_set_serial_console(0);
}
static void __init kafa_init_irq(void)
diff --git a/arch/arm/mach-at91/board-picotux200.c b/arch/arm/mach-at91/board-picotux200.c
index 9d833bb..ac1a3b5 100644
--- a/arch/arm/mach-at91/board-picotux200.c
+++ b/arch/arm/mach-at91/board-picotux200.c
@@ -43,24 +43,21 @@
#include "generic.h"
-/*
- * Serial port configuration.
- * 0 .. 3 = USART0 .. USART3
- * 4 = DBGU
- */
-static struct at91_uart_config __initdata picotux200_uart_config = {
- .console_tty = 0, /* ttyS0 */
- .nr_tty = 2,
- .tty_map = { 4, 1, -1, -1, -1 } /* ttyS0, ..., ttyS4 */
-};
-
static void __init picotux200_map_io(void)
{
/* Initialize processor: 18.432 MHz crystal */
at91rm9200_initialize(18432000, AT91RM9200_BGA);
- /* Setup the serial ports and console */
- at91_init_serial(&picotux200_uart_config);
+ /* DBGU on ttyS0. (Rx & Tx only) */
+ at91_register_uart(0, 0, 0);
+
+ /* USART1 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
+ at91_register_uart(AT91RM9200_ID_US1, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
+ | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
+ | ATMEL_UART_RI);
+
+ /* set serial console to ttyS0 (ie, DBGU) */
+ at91_set_serial_console(0);
}
static void __init picotux200_init_irq(void)
diff --git a/arch/arm/mach-at91/include/mach/board.h b/arch/arm/mach-at91/include/mach/board.h
index 58528aa..2b499eb 100644
--- a/arch/arm/mach-at91/include/mach/board.h
+++ b/arch/arm/mach-at91/include/mach/board.h
@@ -137,13 +137,7 @@ extern void __init at91_add_device_spi(struct spi_board_info *devices, int nr_de
extern void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins);
extern void __init at91_set_serial_console(unsigned portnr);
-struct at91_uart_config {
- unsigned short console_tty; /* tty number of serial console */
- unsigned short nr_tty; /* number of serial tty's */
- short tty_map[]; /* map UART to tty number */
-};
extern struct platform_device *atmel_default_console_device;
-extern void __init __deprecated at91_init_serial(struct at91_uart_config *config);
struct atmel_uart_data {
short use_dma_tx; /* use transmit DMA? */
--
1.7.1
More information about the linux-arm-kernel
mailing list