[PATCH v2 07/18] OMAP2xxx clock: move the DVFS virtual clock code into mach-omap2/clkt2xxx_virt_prcm_set.c
Paul Walmsley
paul at pwsan.com
Tue Jan 19 18:36:10 EST 2010
Move the DVFS virtual clock functions from clock2xxx.c to
mach-omap2/clkt2xxx_virt_prcm_set.c. This is intended to make the
clock code easier to understand, since all of the functions needed to
manage the virt_prcm_set clock are now located in their own file,
rather than being mixed with other, unrelated functions.
Clock debugging is also now more finely-grained, since the DEBUG macro
can now be defined for the virt_prcm_set clock alone. This should
reduce unnecessary console noise when debugging.
Also, if at some future point the mach-omap2/ directory is split into
OMAP2/3/4 variants, this clkt file can be placed in the mach-omap2xxx/
directory, rather than shared with other chip types that don't use
this clock type.
Thanks to Alexander Shishkin <virtuoso at slind.org> for his comments.
Signed-off-by: Paul Walmsley <paul at pwsan.com>
Cc: Richard Woodruff <r-woodruff2 at ti.com>
Cc: Alexander Shishkin <virtuoso at slind.org>
---
arch/arm/mach-omap2/Makefile | 3
arch/arm/mach-omap2/clkt2xxx_virt_prcm_set.c | 254 ++++++++++++++++++++++++++
arch/arm/mach-omap2/clock2xxx.c | 211 ----------------------
3 files changed, 256 insertions(+), 212 deletions(-)
create mode 100644 arch/arm/mach-omap2/clkt2xxx_virt_prcm_set.c
diff --git a/arch/arm/mach-omap2/Makefile b/arch/arm/mach-omap2/Makefile
index 04ce372..2b58363 100644
--- a/arch/arm/mach-omap2/Makefile
+++ b/arch/arm/mach-omap2/Makefile
@@ -11,7 +11,8 @@ prcm-common = prcm.o powerdomain.o
clock-common = clock.o clock_common_data.o \
clockdomain.o clkt_dpll.o \
clkt_clksel.o
-clock-omap2xxx = clkt2xxx_dpllcore.o
+clock-omap2xxx = clkt2xxx_dpllcore.o \
+ clkt2xxx_virt_prcm_set.o
obj-$(CONFIG_ARCH_OMAP2) += $(omap-2-3-common) $(prcm-common) $(clock-common) \
$(clock-omap2xxx)
diff --git a/arch/arm/mach-omap2/clkt2xxx_virt_prcm_set.c b/arch/arm/mach-omap2/clkt2xxx_virt_prcm_set.c
new file mode 100644
index 0000000..7174d09
--- /dev/null
+++ b/arch/arm/mach-omap2/clkt2xxx_virt_prcm_set.c
@@ -0,0 +1,254 @@
+/*
+ * OMAP2xxx DVFS virtual clock functions
+ *
+ * Copyright (C) 2005-2008 Texas Instruments, Inc.
+ * Copyright (C) 2004-2010 Nokia Corporation
+ *
+ * Contacts:
+ * Richard Woodruff <r-woodruff2 at ti.com>
+ * Paul Walmsley
+ *
+ * Based on earlier work by Tuukka Tikkanen, Tony Lindgren,
+ * Gordon McNutt and RidgeRun, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * XXX Some of this code should be replaceable by the upcoming OPP layer
+ * code. However, some notion of "rate set" is probably still necessary
+ * for OMAP2xxx at least. Rate sets should be generalized so they can be
+ * used for any OMAP chip, not just OMAP2xxx. In particular, Richard Woodruff
+ * has in the past expressed a preference to use rate sets for OPP changes,
+ * rather than dynamically recalculating the clock tree, so if someone wants
+ * this badly enough to write the code to handle it, we should support it
+ * as an option.
+ */
+#undef DEBUG
+
+#include <linux/kernel.h>
+#include <linux/errno.h>
+#include <linux/clk.h>
+#include <linux/io.h>
+#include <linux/cpufreq.h>
+
+#include <plat/clock.h>
+#include <plat/sram.h>
+#include <plat/sdrc.h>
+
+#include "clock.h"
+#include "clock2xxx.h"
+#include "opp2xxx.h"
+#include "cm.h"
+#include "cm-regbits-24xx.h"
+
+const struct prcm_config *curr_prcm_set;
+const struct prcm_config *rate_table;
+
+/**
+ * omap2_table_mpu_recalc - just return the MPU speed
+ * @clk: virt_prcm_set struct clk
+ *
+ * Set virt_prcm_set's rate to the mpu_speed field of the current PRCM set.
+ */
+unsigned long omap2_table_mpu_recalc(struct clk *clk)
+{
+ return curr_prcm_set->mpu_speed;
+}
+
+/*
+ * Look for a rate equal or less than the target rate given a configuration set.
+ *
+ * What's not entirely clear is "which" field represents the key field.
+ * Some might argue L3-DDR, others ARM, others IVA. This code is simple and
+ * just uses the ARM rates.
+ */
+long omap2_round_to_table_rate(struct clk *clk, unsigned long rate)
+{
+ const struct prcm_config *ptr;
+ long highest_rate;
+ long sys_ck_rate;
+
+ sys_ck_rate = clk_get_rate(sclk);
+
+ highest_rate = -EINVAL;
+
+ for (ptr = rate_table; ptr->mpu_speed; ptr++) {
+ if (!(ptr->flags & cpu_mask))
+ continue;
+ if (ptr->xtal_speed != sys_ck_rate)
+ continue;
+
+ highest_rate = ptr->mpu_speed;
+
+ /* Can check only after xtal frequency check */
+ if (ptr->mpu_speed <= rate)
+ break;
+ }
+ return highest_rate;
+}
+
+/* Sets basic clocks based on the specified rate */
+int omap2_select_table_rate(struct clk *clk, unsigned long rate)
+{
+ u32 cur_rate, done_rate, bypass = 0, tmp;
+ const struct prcm_config *prcm;
+ unsigned long found_speed = 0;
+ unsigned long flags;
+ long sys_ck_rate;
+
+ sys_ck_rate = clk_get_rate(sclk);
+
+ for (prcm = rate_table; prcm->mpu_speed; prcm++) {
+ if (!(prcm->flags & cpu_mask))
+ continue;
+
+ if (prcm->xtal_speed != sys_ck_rate)
+ continue;
+
+ if (prcm->mpu_speed <= rate) {
+ found_speed = prcm->mpu_speed;
+ break;
+ }
+ }
+
+ if (!found_speed) {
+ printk(KERN_INFO "Could not set MPU rate to %luMHz\n",
+ rate / 1000000);
+ return -EINVAL;
+ }
+
+ curr_prcm_set = prcm;
+ cur_rate = omap2xxx_clk_get_core_rate(dclk);
+
+ if (prcm->dpll_speed == cur_rate / 2) {
+ omap2xxx_sdrc_reprogram(CORE_CLK_SRC_DPLL, 1);
+ } else if (prcm->dpll_speed == cur_rate * 2) {
+ omap2xxx_sdrc_reprogram(CORE_CLK_SRC_DPLL_X2, 1);
+ } else if (prcm->dpll_speed != cur_rate) {
+ local_irq_save(flags);
+
+ if (prcm->dpll_speed == prcm->xtal_speed)
+ bypass = 1;
+
+ if ((prcm->cm_clksel2_pll & OMAP24XX_CORE_CLK_SRC_MASK) ==
+ CORE_CLK_SRC_DPLL_X2)
+ done_rate = CORE_CLK_SRC_DPLL_X2;
+ else
+ done_rate = CORE_CLK_SRC_DPLL;
+
+ /* MPU divider */
+ cm_write_mod_reg(prcm->cm_clksel_mpu, MPU_MOD, CM_CLKSEL);
+
+ /* dsp + iva1 div(2420), iva2.1(2430) */
+ cm_write_mod_reg(prcm->cm_clksel_dsp,
+ OMAP24XX_DSP_MOD, CM_CLKSEL);
+
+ cm_write_mod_reg(prcm->cm_clksel_gfx, GFX_MOD, CM_CLKSEL);
+
+ /* Major subsystem dividers */
+ tmp = cm_read_mod_reg(CORE_MOD, CM_CLKSEL1) & OMAP24XX_CLKSEL_DSS2_MASK;
+ cm_write_mod_reg(prcm->cm_clksel1_core | tmp, CORE_MOD,
+ CM_CLKSEL1);
+
+ if (cpu_is_omap2430())
+ cm_write_mod_reg(prcm->cm_clksel_mdm,
+ OMAP2430_MDM_MOD, CM_CLKSEL);
+
+ /* x2 to enter omap2xxx_sdrc_init_params() */
+ omap2xxx_sdrc_reprogram(CORE_CLK_SRC_DPLL_X2, 1);
+
+ omap2_set_prcm(prcm->cm_clksel1_pll, prcm->base_sdrc_rfr,
+ bypass);
+
+ omap2xxx_sdrc_init_params(omap2xxx_sdrc_dll_is_unlocked());
+ omap2xxx_sdrc_reprogram(done_rate, 0);
+
+ local_irq_restore(flags);
+ }
+
+ return 0;
+}
+
+#ifdef CONFIG_CPU_FREQ
+/*
+ * Walk PRCM rate table and fillout cpufreq freq_table
+ * XXX This should be replaced by an OPP layer in the near future
+ */
+static struct cpufreq_frequency_table *freq_table;
+
+void omap2xxx_clk_init_cpufreq_table(struct cpufreq_frequency_table **table)
+{
+ const struct prcm_config *prcm;
+ long sys_ck_rate;
+ int i = 0;
+ int tbl_sz = 0;
+
+ if (!cpu_is_omap2xxx())
+ return;
+
+ sys_ck_rate = clk_get_rate(sclk);
+
+ for (prcm = rate_table; prcm->mpu_speed; prcm++) {
+ if (!(prcm->flags & cpu_mask))
+ continue;
+ if (prcm->xtal_speed != sys_ck_rate)
+ continue;
+
+ /* don't put bypass rates in table */
+ if (prcm->dpll_speed == prcm->xtal_speed)
+ continue;
+
+ tbl_sz++;
+ }
+
+ /*
+ * XXX Ensure that we're doing what CPUFreq expects for this error
+ * case and the following one
+ */
+ if (tbl_sz == 0) {
+ pr_warning("%s: no matching entries in rate_table\n",
+ __func__);
+ return;
+ }
+
+ /* Include the CPUFREQ_TABLE_END terminator entry */
+ tbl_sz++;
+
+ freq_table = kzalloc(sizeof(struct cpufreq_frequency_table) * tbl_sz,
+ GFP_ATOMIC);
+ if (!freq_table) {
+ pr_err("%s: could not kzalloc frequency table\n", __func__);
+ return;
+ }
+
+ for (prcm = rate_table; prcm->mpu_speed; prcm++) {
+ if (!(prcm->flags & cpu_mask))
+ continue;
+ if (prcm->xtal_speed != sys_ck_rate)
+ continue;
+
+ /* don't put bypass rates in table */
+ if (prcm->dpll_speed == prcm->xtal_speed)
+ continue;
+
+ freq_table[i].index = i;
+ freq_table[i].frequency = prcm->mpu_speed / 1000;
+ i++;
+ }
+
+ freq_table[i].index = i;
+ freq_table[i].frequency = CPUFREQ_TABLE_END;
+
+ *table = &freq_table[0];
+}
+
+void omap2xxx_clk_exit_cpufreq_table(struct cpufreq_frequency_table **table)
+{
+ if (!cpu_is_omap2xxx())
+ return;
+
+ kfree(freq_table);
+}
+
+#endif
diff --git a/arch/arm/mach-omap2/clock2xxx.c b/arch/arm/mach-omap2/clock2xxx.c
index 419ae80..11d6edb 100644
--- a/arch/arm/mach-omap2/clock2xxx.c
+++ b/arch/arm/mach-omap2/clock2xxx.c
@@ -54,9 +54,6 @@
#define APLLS_CLKIN_13MHZ 2
#define APLLS_CLKIN_12MHZ 3
-const struct prcm_config *curr_prcm_set;
-const struct prcm_config *rate_table;
-
struct clk *vclk, *sclk, *dclk;
void __iomem *prcm_clksrc_ctrl;
@@ -185,214 +182,6 @@ const struct clkops clkops_apll54 = {
.disable = omap2_clk_apll_disable,
};
-/**
- * omap2_table_mpu_recalc - just return the MPU speed
- * @clk: virt_prcm_set struct clk
- *
- * Set virt_prcm_set's rate to the mpu_speed field of the current PRCM set.
- */
-unsigned long omap2_table_mpu_recalc(struct clk *clk)
-{
- return curr_prcm_set->mpu_speed;
-}
-
-/*
- * Look for a rate equal or less than the target rate given a configuration set.
- *
- * What's not entirely clear is "which" field represents the key field.
- * Some might argue L3-DDR, others ARM, others IVA. This code is simple and
- * just uses the ARM rates.
- */
-long omap2_round_to_table_rate(struct clk *clk, unsigned long rate)
-{
- const struct prcm_config *ptr;
- long highest_rate;
- long sys_ck_rate;
-
- sys_ck_rate = clk_get_rate(sclk);
-
- highest_rate = -EINVAL;
-
- for (ptr = rate_table; ptr->mpu_speed; ptr++) {
- if (!(ptr->flags & cpu_mask))
- continue;
- if (ptr->xtal_speed != sys_ck_rate)
- continue;
-
- highest_rate = ptr->mpu_speed;
-
- /* Can check only after xtal frequency check */
- if (ptr->mpu_speed <= rate)
- break;
- }
- return highest_rate;
-}
-
-/* Sets basic clocks based on the specified rate */
-int omap2_select_table_rate(struct clk *clk, unsigned long rate)
-{
- u32 cur_rate, done_rate, bypass = 0, tmp;
- const struct prcm_config *prcm;
- unsigned long found_speed = 0;
- unsigned long flags;
- long sys_ck_rate;
-
- sys_ck_rate = clk_get_rate(sclk);
-
- for (prcm = rate_table; prcm->mpu_speed; prcm++) {
- if (!(prcm->flags & cpu_mask))
- continue;
-
- if (prcm->xtal_speed != sys_ck_rate)
- continue;
-
- if (prcm->mpu_speed <= rate) {
- found_speed = prcm->mpu_speed;
- break;
- }
- }
-
- if (!found_speed) {
- printk(KERN_INFO "Could not set MPU rate to %luMHz\n",
- rate / 1000000);
- return -EINVAL;
- }
-
- curr_prcm_set = prcm;
- cur_rate = omap2xxx_clk_get_core_rate(dclk);
-
- if (prcm->dpll_speed == cur_rate / 2) {
- omap2xxx_sdrc_reprogram(CORE_CLK_SRC_DPLL, 1);
- } else if (prcm->dpll_speed == cur_rate * 2) {
- omap2xxx_sdrc_reprogram(CORE_CLK_SRC_DPLL_X2, 1);
- } else if (prcm->dpll_speed != cur_rate) {
- local_irq_save(flags);
-
- if (prcm->dpll_speed == prcm->xtal_speed)
- bypass = 1;
-
- if ((prcm->cm_clksel2_pll & OMAP24XX_CORE_CLK_SRC_MASK) ==
- CORE_CLK_SRC_DPLL_X2)
- done_rate = CORE_CLK_SRC_DPLL_X2;
- else
- done_rate = CORE_CLK_SRC_DPLL;
-
- /* MPU divider */
- cm_write_mod_reg(prcm->cm_clksel_mpu, MPU_MOD, CM_CLKSEL);
-
- /* dsp + iva1 div(2420), iva2.1(2430) */
- cm_write_mod_reg(prcm->cm_clksel_dsp,
- OMAP24XX_DSP_MOD, CM_CLKSEL);
-
- cm_write_mod_reg(prcm->cm_clksel_gfx, GFX_MOD, CM_CLKSEL);
-
- /* Major subsystem dividers */
- tmp = cm_read_mod_reg(CORE_MOD, CM_CLKSEL1) & OMAP24XX_CLKSEL_DSS2_MASK;
- cm_write_mod_reg(prcm->cm_clksel1_core | tmp, CORE_MOD,
- CM_CLKSEL1);
-
- if (cpu_is_omap2430())
- cm_write_mod_reg(prcm->cm_clksel_mdm,
- OMAP2430_MDM_MOD, CM_CLKSEL);
-
- /* x2 to enter omap2xxx_sdrc_init_params() */
- omap2xxx_sdrc_reprogram(CORE_CLK_SRC_DPLL_X2, 1);
-
- omap2_set_prcm(prcm->cm_clksel1_pll, prcm->base_sdrc_rfr,
- bypass);
-
- omap2xxx_sdrc_init_params(omap2xxx_sdrc_dll_is_unlocked());
- omap2xxx_sdrc_reprogram(done_rate, 0);
-
- local_irq_restore(flags);
- }
-
- return 0;
-}
-
-#ifdef CONFIG_CPU_FREQ
-/*
- * Walk PRCM rate table and fillout cpufreq freq_table
- * XXX This should be replaced by an OPP layer in the near future
- */
-static struct cpufreq_frequency_table *freq_table;
-
-void omap2xxx_clk_init_cpufreq_table(struct cpufreq_frequency_table **table)
-{
- const struct prcm_config *prcm;
- long sys_ck_rate;
- int i = 0;
- int tbl_sz = 0;
-
- if (!cpu_is_omap2xxx())
- return;
-
- sys_ck_rate = clk_get_rate(sclk);
-
- for (prcm = rate_table; prcm->mpu_speed; prcm++) {
- if (!(prcm->flags & cpu_mask))
- continue;
- if (prcm->xtal_speed != sys_ck_rate)
- continue;
-
- /* don't put bypass rates in table */
- if (prcm->dpll_speed == prcm->xtal_speed)
- continue;
-
- tbl_sz++;
- }
-
- /*
- * XXX Ensure that we're doing what CPUFreq expects for this error
- * case and the following one
- */
- if (tbl_sz == 0) {
- pr_warning("%s: no matching entries in rate_table\n",
- __func__);
- return;
- }
-
- /* Include the CPUFREQ_TABLE_END terminator entry */
- tbl_sz++;
-
- freq_table = kzalloc(sizeof(struct cpufreq_frequency_table) * tbl_sz,
- GFP_ATOMIC);
- if (!freq_table) {
- pr_err("%s: could not kzalloc frequency table\n", __func__);
- return;
- }
-
- for (prcm = rate_table; prcm->mpu_speed; prcm++) {
- if (!(prcm->flags & cpu_mask))
- continue;
- if (prcm->xtal_speed != sys_ck_rate)
- continue;
-
- /* don't put bypass rates in table */
- if (prcm->dpll_speed == prcm->xtal_speed)
- continue;
-
- freq_table[i].index = i;
- freq_table[i].frequency = prcm->mpu_speed / 1000;
- i++;
- }
-
- freq_table[i].index = i;
- freq_table[i].frequency = CPUFREQ_TABLE_END;
-
- *table = &freq_table[0];
-}
-
-void omap2xxx_clk_exit_cpufreq_table(struct cpufreq_frequency_table **table)
-{
- if (!cpu_is_omap2xxx())
- return;
-
- kfree(freq_table);
-}
-
-#endif
-
static u32 omap2_get_apll_clkin(void)
{
u32 aplls, srate = 0;
More information about the linux-arm-kernel
mailing list