[PATCH - 2nd attempt] ARM: Support for Embedian MXM-8x10 eval kit
Edwin Peer
epeer at tmtservices.co.za
Wed Jan 13 10:30:24 EST 2010
Dear Russell,
Here's another attempt at a patch for the MXM-8x10 development board -- this time against
2.6.33-rc4.
The major difference between this and our previous attempt is that we don't do stupid stuff
with the USB OHCI platform support any more. Aside from the Kconfig and Makefile, this patch
doesn't touch any existing files now.There are also some minor defconfig changes.
Please consider for inclusion.
Thank you.
Regards,
Edwin Peer
Add support for the Embedian MXM-8x10 evaluation kit.
Product URL: http://www.embedian.com/index.php?main_page=product_info&cPath=68&products_id=229
Signed-off-by: Edwin Peer <epeer at tmtservices.co.za>
---
diff -uNrp linux-2.6.33-rc4/arch/arm/configs/capc7117_defconfig linux-embedian-2.6.33-rc4/arch/arm/configs/capc7117_defconfig
--- linux-2.6.33-rc4/arch/arm/configs/capc7117_defconfig 1970-01-01 02:00:00.000000000 +0200
+++ linux-embedian-2.6.33-rc4/arch/arm/configs/capc7117_defconfig 2010-01-13 17:00:13.000000000 +0200
@@ -0,0 +1,1525 @@
+#
+# Automatically generated make config: don't edit
+# Linux kernel version: 2.6.33-rc3
+# Wed Jan 13 16:00:19 2010
+#
+CONFIG_ARM=y
+CONFIG_SYS_SUPPORTS_APM_EMULATION=y
+CONFIG_GENERIC_GPIO=y
+CONFIG_GENERIC_TIME=y
+CONFIG_GENERIC_CLOCKEVENTS=y
+CONFIG_GENERIC_HARDIRQS=y
+CONFIG_STACKTRACE_SUPPORT=y
+CONFIG_HAVE_LATENCYTOP_SUPPORT=y
+CONFIG_LOCKDEP_SUPPORT=y
+CONFIG_TRACE_IRQFLAGS_SUPPORT=y
+CONFIG_HARDIRQS_SW_RESEND=y
+CONFIG_GENERIC_IRQ_PROBE=y
+CONFIG_RWSEM_GENERIC_SPINLOCK=y
+CONFIG_ARCH_HAS_CPUFREQ=y
+CONFIG_GENERIC_HWEIGHT=y
+CONFIG_GENERIC_CALIBRATE_DELAY=y
+CONFIG_ARCH_MTD_XIP=y
+CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
+CONFIG_VECTORS_BASE=0xffff0000
+CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
+
+#
+# General setup
+#
+CONFIG_EXPERIMENTAL=y
+CONFIG_BROKEN_ON_SMP=y
+CONFIG_LOCK_KERNEL=y
+CONFIG_INIT_ENV_ARG_LIMIT=32
+CONFIG_LOCALVERSION=""
+CONFIG_LOCALVERSION_AUTO=y
+# CONFIG_SWAP is not set
+CONFIG_SYSVIPC=y
+CONFIG_SYSVIPC_SYSCTL=y
+CONFIG_POSIX_MQUEUE=y
+CONFIG_POSIX_MQUEUE_SYSCTL=y
+# CONFIG_BSD_PROCESS_ACCT is not set
+# CONFIG_TASKSTATS is not set
+# CONFIG_AUDIT is not set
+
+#
+# RCU Subsystem
+#
+CONFIG_TREE_RCU=y
+# CONFIG_TREE_PREEMPT_RCU is not set
+# CONFIG_TINY_RCU is not set
+# CONFIG_RCU_TRACE is not set
+CONFIG_RCU_FANOUT=32
+# CONFIG_RCU_FANOUT_EXACT is not set
+# CONFIG_TREE_RCU_TRACE is not set
+CONFIG_IKCONFIG=m
+CONFIG_IKCONFIG_PROC=y
+CONFIG_LOG_BUF_SHIFT=14
+# CONFIG_GROUP_SCHED is not set
+# CONFIG_CGROUPS is not set
+CONFIG_SYSFS_DEPRECATED=y
+CONFIG_SYSFS_DEPRECATED_V2=y
+# CONFIG_RELAY is not set
+CONFIG_NAMESPACES=y
+# CONFIG_UTS_NS is not set
+# CONFIG_IPC_NS is not set
+# CONFIG_USER_NS is not set
+# CONFIG_PID_NS is not set
+# CONFIG_NET_NS is not set
+# CONFIG_BLK_DEV_INITRD is not set
+# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
+CONFIG_SYSCTL=y
+CONFIG_ANON_INODES=y
+# CONFIG_EMBEDDED is not set
+CONFIG_UID16=y
+CONFIG_SYSCTL_SYSCALL=y
+CONFIG_KALLSYMS=y
+# CONFIG_KALLSYMS_EXTRA_PASS is not set
+CONFIG_HOTPLUG=y
+CONFIG_PRINTK=y
+CONFIG_BUG=y
+CONFIG_ELF_CORE=y
+CONFIG_BASE_FULL=y
+CONFIG_FUTEX=y
+CONFIG_EPOLL=y
+CONFIG_SIGNALFD=y
+CONFIG_TIMERFD=y
+CONFIG_EVENTFD=y
+CONFIG_SHMEM=y
+CONFIG_AIO=y
+
+#
+# Kernel Performance Events And Counters
+#
+CONFIG_VM_EVENT_COUNTERS=y
+CONFIG_SLUB_DEBUG=y
+# CONFIG_COMPAT_BRK is not set
+# CONFIG_SLAB is not set
+CONFIG_SLUB=y
+# CONFIG_SLOB is not set
+# CONFIG_PROFILING is not set
+CONFIG_HAVE_OPROFILE=y
+# CONFIG_KPROBES is not set
+CONFIG_HAVE_KPROBES=y
+CONFIG_HAVE_KRETPROBES=y
+CONFIG_HAVE_CLK=y
+
+#
+# GCOV-based kernel profiling
+#
+CONFIG_SLOW_WORK=y
+CONFIG_HAVE_GENERIC_DMA_COHERENT=y
+CONFIG_SLABINFO=y
+CONFIG_RT_MUTEXES=y
+CONFIG_BASE_SMALL=0
+CONFIG_MODULES=y
+# CONFIG_MODULE_FORCE_LOAD is not set
+CONFIG_MODULE_UNLOAD=y
+# CONFIG_MODULE_FORCE_UNLOAD is not set
+# CONFIG_MODVERSIONS is not set
+# CONFIG_MODULE_SRCVERSION_ALL is not set
+CONFIG_BLOCK=y
+CONFIG_LBDAF=y
+# CONFIG_BLK_DEV_BSG is not set
+# CONFIG_BLK_DEV_INTEGRITY is not set
+
+#
+# IO Schedulers
+#
+CONFIG_IOSCHED_NOOP=y
+# CONFIG_IOSCHED_DEADLINE is not set
+CONFIG_IOSCHED_CFQ=y
+# CONFIG_DEFAULT_DEADLINE is not set
+CONFIG_DEFAULT_CFQ=y
+# CONFIG_DEFAULT_NOOP is not set
+CONFIG_DEFAULT_IOSCHED="cfq"
+# CONFIG_INLINE_SPIN_TRYLOCK is not set
+# CONFIG_INLINE_SPIN_TRYLOCK_BH is not set
+# CONFIG_INLINE_SPIN_LOCK is not set
+# CONFIG_INLINE_SPIN_LOCK_BH is not set
+# CONFIG_INLINE_SPIN_LOCK_IRQ is not set
+# CONFIG_INLINE_SPIN_LOCK_IRQSAVE is not set
+# CONFIG_INLINE_SPIN_UNLOCK is not set
+# CONFIG_INLINE_SPIN_UNLOCK_BH is not set
+# CONFIG_INLINE_SPIN_UNLOCK_IRQ is not set
+# CONFIG_INLINE_SPIN_UNLOCK_IRQRESTORE is not set
+# CONFIG_INLINE_READ_TRYLOCK is not set
+# CONFIG_INLINE_READ_LOCK is not set
+# CONFIG_INLINE_READ_LOCK_BH is not set
+# CONFIG_INLINE_READ_LOCK_IRQ is not set
+# CONFIG_INLINE_READ_LOCK_IRQSAVE is not set
+# CONFIG_INLINE_READ_UNLOCK is not set
+# CONFIG_INLINE_READ_UNLOCK_BH is not set
+# CONFIG_INLINE_READ_UNLOCK_IRQ is not set
+# CONFIG_INLINE_READ_UNLOCK_IRQRESTORE is not set
+# CONFIG_INLINE_WRITE_TRYLOCK is not set
+# CONFIG_INLINE_WRITE_LOCK is not set
+# CONFIG_INLINE_WRITE_LOCK_BH is not set
+# CONFIG_INLINE_WRITE_LOCK_IRQ is not set
+# CONFIG_INLINE_WRITE_LOCK_IRQSAVE is not set
+# CONFIG_INLINE_WRITE_UNLOCK is not set
+# CONFIG_INLINE_WRITE_UNLOCK_BH is not set
+# CONFIG_INLINE_WRITE_UNLOCK_IRQ is not set
+# CONFIG_INLINE_WRITE_UNLOCK_IRQRESTORE is not set
+# CONFIG_MUTEX_SPIN_ON_OWNER is not set
+# CONFIG_FREEZER is not set
+
+#
+# System Type
+#
+CONFIG_MMU=y
+# CONFIG_ARCH_AAEC2000 is not set
+# CONFIG_ARCH_INTEGRATOR is not set
+# CONFIG_ARCH_REALVIEW is not set
+# CONFIG_ARCH_VERSATILE is not set
+# CONFIG_ARCH_AT91 is not set
+# CONFIG_ARCH_CLPS711X is not set
+# CONFIG_ARCH_GEMINI is not set
+# CONFIG_ARCH_EBSA110 is not set
+# CONFIG_ARCH_EP93XX is not set
+# CONFIG_ARCH_FOOTBRIDGE is not set
+# CONFIG_ARCH_MXC is not set
+# CONFIG_ARCH_STMP3XXX is not set
+# CONFIG_ARCH_NETX is not set
+# CONFIG_ARCH_H720X is not set
+# CONFIG_ARCH_NOMADIK is not set
+# CONFIG_ARCH_IOP13XX is not set
+# CONFIG_ARCH_IOP32X is not set
+# CONFIG_ARCH_IOP33X is not set
+# CONFIG_ARCH_IXP23XX is not set
+# CONFIG_ARCH_IXP2000 is not set
+# CONFIG_ARCH_IXP4XX is not set
+# CONFIG_ARCH_L7200 is not set
+# CONFIG_ARCH_DOVE is not set
+# CONFIG_ARCH_KIRKWOOD is not set
+# CONFIG_ARCH_LOKI is not set
+# CONFIG_ARCH_MV78XX0 is not set
+# CONFIG_ARCH_ORION5X is not set
+# CONFIG_ARCH_MMP is not set
+# CONFIG_ARCH_KS8695 is not set
+# CONFIG_ARCH_NS9XXX is not set
+# CONFIG_ARCH_W90X900 is not set
+# CONFIG_ARCH_PNX4008 is not set
+CONFIG_ARCH_PXA=y
+# CONFIG_ARCH_MSM is not set
+# CONFIG_ARCH_RPC is not set
+# CONFIG_ARCH_SA1100 is not set
+# CONFIG_ARCH_S3C2410 is not set
+# CONFIG_ARCH_S3C64XX is not set
+# CONFIG_ARCH_S5PC1XX is not set
+# CONFIG_ARCH_SHARK is not set
+# CONFIG_ARCH_LH7A40X is not set
+# CONFIG_ARCH_U300 is not set
+# CONFIG_ARCH_DAVINCI is not set
+# CONFIG_ARCH_OMAP is not set
+# CONFIG_ARCH_BCMRING is not set
+# CONFIG_ARCH_U8500 is not set
+
+#
+# Intel PXA2xx/PXA3xx Implementations
+#
+
+#
+# Intel/Marvell Dev Platforms (sorted by hardware release time)
+#
+# CONFIG_ARCH_LUBBOCK is not set
+# CONFIG_MACH_MAINSTONE is not set
+# CONFIG_MACH_ZYLONITE300 is not set
+# CONFIG_MACH_ZYLONITE320 is not set
+# CONFIG_MACH_LITTLETON is not set
+# CONFIG_MACH_TAVOREVB is not set
+# CONFIG_MACH_SAAR is not set
+
+#
+# Third Party Dev Platforms (sorted by vendor name)
+#
+# CONFIG_ARCH_PXA_IDP is not set
+# CONFIG_ARCH_VIPER is not set
+# CONFIG_MACH_ARCOM_ZEUS is not set
+# CONFIG_MACH_BALLOON3 is not set
+# CONFIG_MACH_CSB726 is not set
+# CONFIG_MACH_ARMCORE is not set
+# CONFIG_MACH_EM_X270 is not set
+# CONFIG_MACH_EXEDA is not set
+# CONFIG_MACH_CM_X300 is not set
+CONFIG_MACH_CAPC7117=y
+# CONFIG_ARCH_GUMSTIX is not set
+# CONFIG_MACH_INTELMOTE2 is not set
+# CONFIG_MACH_STARGATE2 is not set
+# CONFIG_MACH_XCEP is not set
+# CONFIG_TRIZEPS_PXA is not set
+# CONFIG_MACH_LOGICPD_PXA270 is not set
+# CONFIG_MACH_PCM027 is not set
+# CONFIG_MACH_COLIBRI is not set
+# CONFIG_MACH_COLIBRI300 is not set
+# CONFIG_MACH_COLIBRI320 is not set
+
+#
+# End-user Products (sorted by vendor name)
+#
+# CONFIG_MACH_H4700 is not set
+# CONFIG_MACH_H5000 is not set
+# CONFIG_MACH_HIMALAYA is not set
+# CONFIG_MACH_MAGICIAN is not set
+# CONFIG_MACH_MIOA701 is not set
+# CONFIG_PXA_EZX is not set
+# CONFIG_MACH_MP900C is not set
+# CONFIG_ARCH_PXA_PALM is not set
+# CONFIG_PXA_SHARPSL is not set
+# CONFIG_ARCH_PXA_ESERIES is not set
+CONFIG_PXA3xx=y
+CONFIG_CPU_PXA320=y
+CONFIG_PXA_SSP=y
+CONFIG_PLAT_PXA=y
+
+#
+# Processor Type
+#
+CONFIG_CPU_XSC3=y
+CONFIG_CPU_32v5=y
+CONFIG_CPU_ABRT_EV5T=y
+CONFIG_CPU_PABRT_LEGACY=y
+CONFIG_CPU_CACHE_VIVT=y
+CONFIG_CPU_TLB_V4WBI=y
+CONFIG_CPU_CP15=y
+CONFIG_CPU_CP15_MMU=y
+CONFIG_IO_36=y
+
+#
+# Processor Features
+#
+CONFIG_ARM_THUMB=y
+# CONFIG_CPU_DCACHE_DISABLE is not set
+# CONFIG_CPU_BPREDICT_DISABLE is not set
+# CONFIG_CACHE_XSC3L2 is not set
+CONFIG_ARM_L1_CACHE_SHIFT=5
+CONFIG_IWMMXT=y
+CONFIG_COMMON_CLKDEV=y
+
+#
+# Bus support
+#
+# CONFIG_PCI_SYSCALL is not set
+# CONFIG_ARCH_SUPPORTS_MSI is not set
+# CONFIG_PCCARD is not set
+
+#
+# Kernel Features
+#
+CONFIG_TICK_ONESHOT=y
+CONFIG_NO_HZ=y
+CONFIG_HIGH_RES_TIMERS=y
+CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
+CONFIG_VMSPLIT_3G=y
+# CONFIG_VMSPLIT_2G is not set
+# CONFIG_VMSPLIT_1G is not set
+CONFIG_PAGE_OFFSET=0xC0000000
+# CONFIG_PREEMPT_NONE is not set
+# CONFIG_PREEMPT_VOLUNTARY is not set
+CONFIG_PREEMPT=y
+CONFIG_HZ=100
+# CONFIG_AEABI is not set
+# CONFIG_ARCH_SPARSEMEM_DEFAULT is not set
+# CONFIG_ARCH_SELECT_MEMORY_MODEL is not set
+# CONFIG_HIGHMEM is not set
+CONFIG_SELECT_MEMORY_MODEL=y
+CONFIG_FLATMEM_MANUAL=y
+# CONFIG_DISCONTIGMEM_MANUAL is not set
+# CONFIG_SPARSEMEM_MANUAL is not set
+CONFIG_FLATMEM=y
+CONFIG_FLAT_NODE_MEM_MAP=y
+CONFIG_PAGEFLAGS_EXTENDED=y
+CONFIG_SPLIT_PTLOCK_CPUS=999999
+# CONFIG_PHYS_ADDR_T_64BIT is not set
+CONFIG_ZONE_DMA_FLAG=0
+CONFIG_VIRT_TO_BUS=y
+# CONFIG_KSM is not set
+CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
+CONFIG_ALIGNMENT_TRAP=y
+# CONFIG_UACCESS_WITH_MEMCPY is not set
+
+#
+# Boot options
+#
+CONFIG_ZBOOT_ROM_TEXT=0x0
+CONFIG_ZBOOT_ROM_BSS=0x0
+CONFIG_CMDLINE="root=/dev/mtdblock2 rootfstype=jffs2 console=ttyS1,115200 mem=128M init=/linuxrc debug"
+# CONFIG_XIP_KERNEL is not set
+# CONFIG_KEXEC is not set
+
+#
+# CPU Power Management
+#
+# CONFIG_CPU_FREQ is not set
+# CONFIG_CPU_IDLE is not set
+
+#
+# Floating point emulation
+#
+
+#
+# At least one emulation must be selected
+#
+CONFIG_FPE_NWFPE=y
+# CONFIG_FPE_NWFPE_XP is not set
+# CONFIG_FPE_FASTFPE is not set
+
+#
+# Userspace binary formats
+#
+CONFIG_BINFMT_ELF=y
+# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
+CONFIG_HAVE_AOUT=y
+# CONFIG_BINFMT_AOUT is not set
+# CONFIG_BINFMT_MISC is not set
+# CONFIG_ARTHUR is not set
+
+#
+# Power management options
+#
+CONFIG_PM=y
+# CONFIG_PM_DEBUG is not set
+# CONFIG_SUSPEND is not set
+# CONFIG_APM_EMULATION is not set
+# CONFIG_PM_RUNTIME is not set
+CONFIG_ARCH_SUSPEND_POSSIBLE=y
+CONFIG_NET=y
+
+#
+# Networking options
+#
+CONFIG_PACKET=y
+# CONFIG_PACKET_MMAP is not set
+CONFIG_UNIX=y
+# CONFIG_NET_KEY is not set
+CONFIG_INET=y
+# CONFIG_IP_MULTICAST is not set
+# CONFIG_IP_ADVANCED_ROUTER is not set
+CONFIG_IP_FIB_HASH=y
+# CONFIG_IP_PNP is not set
+# CONFIG_NET_IPIP is not set
+# CONFIG_NET_IPGRE is not set
+# CONFIG_ARPD is not set
+CONFIG_SYN_COOKIES=y
+# CONFIG_INET_AH is not set
+# CONFIG_INET_ESP is not set
+# CONFIG_INET_IPCOMP is not set
+# CONFIG_INET_XFRM_TUNNEL is not set
+# CONFIG_INET_TUNNEL is not set
+# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
+# CONFIG_INET_XFRM_MODE_TUNNEL is not set
+# CONFIG_INET_XFRM_MODE_BEET is not set
+# CONFIG_INET_LRO is not set
+CONFIG_INET_DIAG=m
+CONFIG_INET_TCP_DIAG=m
+# CONFIG_TCP_CONG_ADVANCED is not set
+CONFIG_TCP_CONG_CUBIC=y
+CONFIG_DEFAULT_TCP_CONG="cubic"
+# CONFIG_TCP_MD5SIG is not set
+# CONFIG_IPV6 is not set
+# CONFIG_NETLABEL is not set
+# CONFIG_NETWORK_SECMARK is not set
+# CONFIG_NETFILTER is not set
+# CONFIG_IP_DCCP is not set
+# CONFIG_IP_SCTP is not set
+# CONFIG_RDS is not set
+# CONFIG_TIPC is not set
+# CONFIG_ATM is not set
+# CONFIG_BRIDGE is not set
+# CONFIG_NET_DSA is not set
+# CONFIG_VLAN_8021Q is not set
+# CONFIG_DECNET is not set
+# CONFIG_LLC2 is not set
+# CONFIG_IPX is not set
+# CONFIG_ATALK is not set
+# CONFIG_X25 is not set
+# CONFIG_LAPB is not set
+# CONFIG_ECONET is not set
+# CONFIG_WAN_ROUTER is not set
+# CONFIG_PHONET is not set
+# CONFIG_IEEE802154 is not set
+# CONFIG_NET_SCHED is not set
+# CONFIG_DCB is not set
+
+#
+# Network testing
+#
+# CONFIG_NET_PKTGEN is not set
+# CONFIG_HAMRADIO is not set
+CONFIG_CAN=m
+CONFIG_CAN_RAW=m
+# CONFIG_CAN_BCM is not set
+
+#
+# CAN Device Drivers
+#
+CONFIG_CAN_VCAN=m
+CONFIG_CAN_DEV=m
+CONFIG_CAN_CALC_BITTIMING=y
+# CONFIG_CAN_MCP251X is not set
+# CONFIG_CAN_SJA1000 is not set
+
+#
+# CAN USB interfaces
+#
+# CONFIG_CAN_EMS_USB is not set
+CONFIG_CAN_DEBUG_DEVICES=y
+# CONFIG_IRDA is not set
+# CONFIG_BT is not set
+# CONFIG_AF_RXRPC is not set
+CONFIG_WIRELESS=y
+# CONFIG_CFG80211 is not set
+# CONFIG_LIB80211 is not set
+
+#
+# CFG80211 needs to be enabled for MAC80211
+#
+# CONFIG_WIMAX is not set
+# CONFIG_RFKILL is not set
+# CONFIG_NET_9P is not set
+
+#
+# Device Drivers
+#
+
+#
+# Generic Driver Options
+#
+CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+# CONFIG_DEVTMPFS is not set
+CONFIG_STANDALONE=y
+CONFIG_PREVENT_FIRMWARE_BUILD=y
+CONFIG_FW_LOADER=y
+CONFIG_FIRMWARE_IN_KERNEL=y
+CONFIG_EXTRA_FIRMWARE=""
+# CONFIG_SYS_HYPERVISOR is not set
+# CONFIG_CONNECTOR is not set
+CONFIG_MTD=y
+# CONFIG_MTD_DEBUG is not set
+# CONFIG_MTD_TESTS is not set
+# CONFIG_MTD_CONCAT is not set
+CONFIG_MTD_PARTITIONS=y
+# CONFIG_MTD_REDBOOT_PARTS is not set
+# CONFIG_MTD_CMDLINE_PARTS is not set
+# CONFIG_MTD_AFS_PARTS is not set
+# CONFIG_MTD_AR7_PARTS is not set
+
+#
+# User Modules And Translation Layers
+#
+CONFIG_MTD_CHAR=y
+CONFIG_MTD_BLKDEVS=y
+CONFIG_MTD_BLOCK=y
+# CONFIG_FTL is not set
+# CONFIG_NFTL is not set
+# CONFIG_INFTL is not set
+# CONFIG_RFD_FTL is not set
+# CONFIG_SSFDC is not set
+# CONFIG_MTD_OOPS is not set
+
+#
+# RAM/ROM/Flash chip drivers
+#
+# CONFIG_MTD_CFI is not set
+# CONFIG_MTD_JEDECPROBE is not set
+CONFIG_MTD_MAP_BANK_WIDTH_1=y
+CONFIG_MTD_MAP_BANK_WIDTH_2=y
+CONFIG_MTD_MAP_BANK_WIDTH_4=y
+# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set
+CONFIG_MTD_CFI_I1=y
+CONFIG_MTD_CFI_I2=y
+# CONFIG_MTD_CFI_I4 is not set
+# CONFIG_MTD_CFI_I8 is not set
+# CONFIG_MTD_RAM is not set
+# CONFIG_MTD_ROM is not set
+# CONFIG_MTD_ABSENT is not set
+
+#
+# Mapping drivers for chip access
+#
+# CONFIG_MTD_COMPLEX_MAPPINGS is not set
+# CONFIG_MTD_PLATRAM is not set
+
+#
+# Self-contained MTD device drivers
+#
+# CONFIG_MTD_DATAFLASH is not set
+# CONFIG_MTD_M25P80 is not set
+# CONFIG_MTD_SST25L is not set
+# CONFIG_MTD_SLRAM is not set
+# CONFIG_MTD_PHRAM is not set
+# CONFIG_MTD_MTDRAM is not set
+# CONFIG_MTD_BLOCK2MTD is not set
+
+#
+# Disk-On-Chip Device Drivers
+#
+# CONFIG_MTD_DOC2000 is not set
+# CONFIG_MTD_DOC2001 is not set
+# CONFIG_MTD_DOC2001PLUS is not set
+CONFIG_MTD_NAND=y
+# CONFIG_MTD_NAND_VERIFY_WRITE is not set
+# CONFIG_MTD_NAND_ECC_SMC is not set
+# CONFIG_MTD_NAND_MUSEUM_IDS is not set
+# CONFIG_MTD_NAND_H1900 is not set
+# CONFIG_MTD_NAND_GPIO is not set
+CONFIG_MTD_NAND_IDS=y
+# CONFIG_MTD_NAND_DISKONCHIP is not set
+# CONFIG_MTD_NAND_SHARPSL is not set
+CONFIG_MTD_NAND_PXA3xx=y
+# CONFIG_MTD_NAND_PXA3xx_BUILTIN is not set
+# CONFIG_MTD_NAND_NANDSIM is not set
+# CONFIG_MTD_NAND_PLATFORM is not set
+# CONFIG_MTD_ALAUDA is not set
+# CONFIG_MTD_ONENAND is not set
+
+#
+# LPDDR flash memory drivers
+#
+# CONFIG_MTD_LPDDR is not set
+
+#
+# UBI - Unsorted block images
+#
+CONFIG_MTD_UBI=y
+CONFIG_MTD_UBI_WL_THRESHOLD=4096
+CONFIG_MTD_UBI_BEB_RESERVE=1
+# CONFIG_MTD_UBI_GLUEBI is not set
+
+#
+# UBI debugging options
+#
+# CONFIG_MTD_UBI_DEBUG is not set
+# CONFIG_PARPORT is not set
+CONFIG_BLK_DEV=y
+# CONFIG_BLK_DEV_COW_COMMON is not set
+CONFIG_BLK_DEV_LOOP=m
+# CONFIG_BLK_DEV_CRYPTOLOOP is not set
+
+#
+# DRBD disabled because PROC_FS, INET or CONNECTOR not selected
+#
+# CONFIG_BLK_DEV_NBD is not set
+# CONFIG_BLK_DEV_UB is not set
+# CONFIG_BLK_DEV_RAM is not set
+# CONFIG_CDROM_PKTCDVD is not set
+# CONFIG_ATA_OVER_ETH is not set
+# CONFIG_MG_DISK is not set
+# CONFIG_MISC_DEVICES is not set
+CONFIG_HAVE_IDE=y
+# CONFIG_IDE is not set
+
+#
+# SCSI device support
+#
+# CONFIG_RAID_ATTRS is not set
+CONFIG_SCSI=m
+CONFIG_SCSI_DMA=y
+# CONFIG_SCSI_TGT is not set
+# CONFIG_SCSI_NETLINK is not set
+# CONFIG_SCSI_PROC_FS is not set
+
+#
+# SCSI support type (disk, tape, CD-ROM)
+#
+CONFIG_BLK_DEV_SD=m
+# CONFIG_CHR_DEV_ST is not set
+# CONFIG_CHR_DEV_OSST is not set
+# CONFIG_BLK_DEV_SR is not set
+# CONFIG_CHR_DEV_SG is not set
+# CONFIG_CHR_DEV_SCH is not set
+# CONFIG_SCSI_MULTI_LUN is not set
+# CONFIG_SCSI_CONSTANTS is not set
+# CONFIG_SCSI_LOGGING is not set
+# CONFIG_SCSI_SCAN_ASYNC is not set
+CONFIG_SCSI_WAIT_SCAN=m
+
+#
+# SCSI Transports
+#
+# CONFIG_SCSI_SPI_ATTRS is not set
+# CONFIG_SCSI_FC_ATTRS is not set
+# CONFIG_SCSI_ISCSI_ATTRS is not set
+# CONFIG_SCSI_SAS_LIBSAS is not set
+# CONFIG_SCSI_SRP_ATTRS is not set
+# CONFIG_SCSI_LOWLEVEL is not set
+# CONFIG_SCSI_DH is not set
+# CONFIG_SCSI_OSD_INITIATOR is not set
+# CONFIG_ATA is not set
+# CONFIG_MD is not set
+CONFIG_NETDEVICES=y
+# CONFIG_DUMMY is not set
+# CONFIG_BONDING is not set
+# CONFIG_MACVLAN is not set
+# CONFIG_EQUALIZER is not set
+# CONFIG_TUN is not set
+# CONFIG_VETH is not set
+# CONFIG_PHYLIB is not set
+CONFIG_NET_ETHERNET=y
+CONFIG_MII=y
+# CONFIG_AX88796 is not set
+# CONFIG_SMC91X is not set
+CONFIG_DM9000=y
+CONFIG_DM9000_DEBUGLEVEL=4
+# CONFIG_DM9000_FORCE_SIMPLE_PHY_POLL is not set
+# CONFIG_ENC28J60 is not set
+# CONFIG_ETHOC is not set
+# CONFIG_SMC911X is not set
+# CONFIG_SMSC911X is not set
+# CONFIG_DNET is not set
+# CONFIG_IBM_NEW_EMAC_ZMII is not set
+# CONFIG_IBM_NEW_EMAC_RGMII is not set
+# CONFIG_IBM_NEW_EMAC_TAH is not set
+# CONFIG_IBM_NEW_EMAC_EMAC4 is not set
+# CONFIG_IBM_NEW_EMAC_NO_FLOW_CTRL is not set
+# CONFIG_IBM_NEW_EMAC_MAL_CLR_ICINTSTAT is not set
+# CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set
+# CONFIG_B44 is not set
+# CONFIG_KS8842 is not set
+# CONFIG_KS8851 is not set
+# CONFIG_KS8851_MLL is not set
+# CONFIG_NETDEV_1000 is not set
+# CONFIG_NETDEV_10000 is not set
+CONFIG_WLAN=y
+# CONFIG_USB_ZD1201 is not set
+# CONFIG_HOSTAP is not set
+
+#
+# Enable WiMAX (Networking options) to see the WiMAX drivers
+#
+
+#
+# USB Network Adapters
+#
+# CONFIG_USB_CATC is not set
+# CONFIG_USB_KAWETH is not set
+# CONFIG_USB_PEGASUS is not set
+# CONFIG_USB_RTL8150 is not set
+# CONFIG_USB_USBNET is not set
+# CONFIG_WAN is not set
+# CONFIG_PPP is not set
+# CONFIG_SLIP is not set
+# CONFIG_NETCONSOLE is not set
+# CONFIG_NETPOLL is not set
+# CONFIG_NET_POLL_CONTROLLER is not set
+# CONFIG_ISDN is not set
+# CONFIG_PHONE is not set
+
+#
+# Input device support
+#
+CONFIG_INPUT=y
+# CONFIG_INPUT_FF_MEMLESS is not set
+# CONFIG_INPUT_POLLDEV is not set
+# CONFIG_INPUT_SPARSEKMAP is not set
+
+#
+# Userland interfaces
+#
+CONFIG_INPUT_MOUSEDEV=y
+# CONFIG_INPUT_MOUSEDEV_PSAUX is not set
+CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
+CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
+# CONFIG_INPUT_JOYDEV is not set
+# CONFIG_INPUT_EVDEV is not set
+# CONFIG_INPUT_EVBUG is not set
+
+#
+# Input Device Drivers
+#
+# CONFIG_INPUT_KEYBOARD is not set
+# CONFIG_INPUT_MOUSE is not set
+# CONFIG_INPUT_JOYSTICK is not set
+# CONFIG_INPUT_TABLET is not set
+# CONFIG_INPUT_TOUCHSCREEN is not set
+# CONFIG_INPUT_MISC is not set
+
+#
+# Hardware I/O ports
+#
+CONFIG_SERIO=y
+CONFIG_SERIO_SERPORT=y
+# CONFIG_SERIO_RAW is not set
+# CONFIG_SERIO_ALTERA_PS2 is not set
+# CONFIG_GAMEPORT is not set
+
+#
+# Character devices
+#
+CONFIG_VT=y
+CONFIG_CONSOLE_TRANSLATIONS=y
+CONFIG_VT_CONSOLE=y
+CONFIG_HW_CONSOLE=y
+# CONFIG_VT_HW_CONSOLE_BINDING is not set
+CONFIG_DEVKMEM=y
+# CONFIG_SERIAL_NONSTANDARD is not set
+
+#
+# Serial drivers
+#
+# CONFIG_SERIAL_8250 is not set
+
+#
+# Non-8250 serial port support
+#
+# CONFIG_SERIAL_MAX3100 is not set
+CONFIG_SERIAL_PXA=y
+CONFIG_SERIAL_PXA_CONSOLE=y
+CONFIG_SERIAL_CORE=y
+CONFIG_SERIAL_CORE_CONSOLE=y
+CONFIG_UNIX98_PTYS=y
+# CONFIG_DEVPTS_MULTIPLE_INSTANCES is not set
+# CONFIG_LEGACY_PTYS is not set
+# CONFIG_IPMI_HANDLER is not set
+# CONFIG_HW_RANDOM is not set
+# CONFIG_R3964 is not set
+# CONFIG_RAW_DRIVER is not set
+# CONFIG_TCG_TPM is not set
+CONFIG_I2C=y
+CONFIG_I2C_BOARDINFO=y
+CONFIG_I2C_COMPAT=y
+CONFIG_I2C_CHARDEV=y
+CONFIG_I2C_HELPER_AUTO=y
+
+#
+# I2C Hardware Bus support
+#
+
+#
+# I2C system bus drivers (mostly embedded / system-on-chip)
+#
+# CONFIG_I2C_DESIGNWARE is not set
+# CONFIG_I2C_GPIO is not set
+# CONFIG_I2C_OCORES is not set
+CONFIG_I2C_PXA=y
+# CONFIG_I2C_PXA_SLAVE is not set
+# CONFIG_I2C_SIMTEC is not set
+
+#
+# External I2C/SMBus adapter drivers
+#
+# CONFIG_I2C_PARPORT_LIGHT is not set
+# CONFIG_I2C_TAOS_EVM is not set
+# CONFIG_I2C_TINY_USB is not set
+
+#
+# Other I2C/SMBus bus drivers
+#
+# CONFIG_I2C_PCA_PLATFORM is not set
+# CONFIG_I2C_STUB is not set
+
+#
+# Miscellaneous I2C Chip support
+#
+# CONFIG_SENSORS_TSL2550 is not set
+CONFIG_I2C_DEBUG_CORE=y
+CONFIG_I2C_DEBUG_ALGO=y
+CONFIG_I2C_DEBUG_BUS=y
+CONFIG_I2C_DEBUG_CHIP=y
+CONFIG_SPI=y
+CONFIG_SPI_MASTER=y
+
+#
+# SPI Master Controller Drivers
+#
+# CONFIG_SPI_BITBANG is not set
+# CONFIG_SPI_GPIO is not set
+CONFIG_SPI_PXA2XX=y
+# CONFIG_SPI_XILINX is not set
+# CONFIG_SPI_DESIGNWARE is not set
+
+#
+# SPI Protocol Masters
+#
+# CONFIG_SPI_SPIDEV is not set
+# CONFIG_SPI_TLE62X0 is not set
+
+#
+# PPS support
+#
+# CONFIG_PPS is not set
+CONFIG_ARCH_REQUIRE_GPIOLIB=y
+CONFIG_GPIOLIB=y
+# CONFIG_GPIO_SYSFS is not set
+
+#
+# Memory mapped GPIO expanders:
+#
+
+#
+# I2C GPIO expanders:
+#
+# CONFIG_GPIO_MAX732X is not set
+# CONFIG_GPIO_PCA953X is not set
+# CONFIG_GPIO_PCF857X is not set
+
+#
+# PCI GPIO expanders:
+#
+
+#
+# SPI GPIO expanders:
+#
+# CONFIG_GPIO_MAX7301 is not set
+# CONFIG_GPIO_MCP23S08 is not set
+# CONFIG_GPIO_MC33880 is not set
+
+#
+# AC97 GPIO expanders:
+#
+# CONFIG_W1 is not set
+# CONFIG_POWER_SUPPLY is not set
+# CONFIG_HWMON is not set
+# CONFIG_THERMAL is not set
+CONFIG_WATCHDOG=y
+# CONFIG_WATCHDOG_NOWAYOUT is not set
+
+#
+# Watchdog Device Drivers
+#
+# CONFIG_SOFT_WATCHDOG is not set
+CONFIG_SA1100_WATCHDOG=m
+
+#
+# USB-based Watchdog Cards
+#
+# CONFIG_USBPCWATCHDOG is not set
+CONFIG_SSB_POSSIBLE=y
+
+#
+# Sonics Silicon Backplane
+#
+# CONFIG_SSB is not set
+
+#
+# Multifunction device drivers
+#
+# CONFIG_MFD_CORE is not set
+# CONFIG_MFD_SM501 is not set
+# CONFIG_MFD_ASIC3 is not set
+# CONFIG_HTC_EGPIO is not set
+# CONFIG_HTC_PASIC3 is not set
+# CONFIG_TPS65010 is not set
+# CONFIG_TWL4030_CORE is not set
+# CONFIG_MFD_TMIO is not set
+# CONFIG_MFD_T7L66XB is not set
+# CONFIG_MFD_TC6387XB is not set
+# CONFIG_MFD_TC6393XB is not set
+# CONFIG_PMIC_DA903X is not set
+# CONFIG_PMIC_ADP5520 is not set
+# CONFIG_MFD_WM8400 is not set
+# CONFIG_MFD_WM831X is not set
+# CONFIG_MFD_WM8350_I2C is not set
+# CONFIG_MFD_PCF50633 is not set
+# CONFIG_MFD_MC13783 is not set
+# CONFIG_AB3100_CORE is not set
+# CONFIG_EZX_PCAP is not set
+# CONFIG_MFD_88PM8607 is not set
+# CONFIG_AB4500_CORE is not set
+# CONFIG_REGULATOR is not set
+# CONFIG_MEDIA_SUPPORT is not set
+
+#
+# Graphics support
+#
+# CONFIG_VGASTATE is not set
+# CONFIG_VIDEO_OUTPUT_CONTROL is not set
+# CONFIG_FB is not set
+# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
+
+#
+# Display device support
+#
+CONFIG_DISPLAY_SUPPORT=m
+
+#
+# Display hardware drivers
+#
+
+#
+# Console display driver support
+#
+# CONFIG_VGA_CONSOLE is not set
+CONFIG_DUMMY_CONSOLE=y
+# CONFIG_SOUND is not set
+# CONFIG_HID_SUPPORT is not set
+CONFIG_USB_SUPPORT=y
+CONFIG_USB_ARCH_HAS_HCD=y
+CONFIG_USB_ARCH_HAS_OHCI=y
+# CONFIG_USB_ARCH_HAS_EHCI is not set
+CONFIG_USB=y
+# CONFIG_USB_DEBUG is not set
+# CONFIG_USB_ANNOUNCE_NEW_DEVICES is not set
+
+#
+# Miscellaneous USB options
+#
+CONFIG_USB_DEVICEFS=y
+CONFIG_USB_DEVICE_CLASS=y
+# CONFIG_USB_DYNAMIC_MINORS is not set
+# CONFIG_USB_SUSPEND is not set
+# CONFIG_USB_OTG is not set
+# CONFIG_USB_MON is not set
+# CONFIG_USB_WUSB is not set
+# CONFIG_USB_WUSB_CBAF is not set
+
+#
+# USB Host Controller Drivers
+#
+# CONFIG_USB_C67X00_HCD is not set
+# CONFIG_USB_OXU210HP_HCD is not set
+# CONFIG_USB_ISP116X_HCD is not set
+# CONFIG_USB_ISP1760_HCD is not set
+# CONFIG_USB_ISP1362_HCD is not set
+CONFIG_USB_OHCI_HCD=y
+# CONFIG_USB_OHCI_BIG_ENDIAN_DESC is not set
+# CONFIG_USB_OHCI_BIG_ENDIAN_MMIO is not set
+CONFIG_USB_OHCI_LITTLE_ENDIAN=y
+# CONFIG_USB_SL811_HCD is not set
+# CONFIG_USB_R8A66597_HCD is not set
+# CONFIG_USB_HWA_HCD is not set
+# CONFIG_USB_MUSB_HDRC is not set
+
+#
+# USB Device Class drivers
+#
+# CONFIG_USB_ACM is not set
+# CONFIG_USB_PRINTER is not set
+# CONFIG_USB_WDM is not set
+# CONFIG_USB_TMC is not set
+
+#
+# NOTE: USB_STORAGE depends on SCSI but BLK_DEV_SD may
+#
+
+#
+# also be needed; see USB_STORAGE Help for more info
+#
+CONFIG_USB_STORAGE=m
+# CONFIG_USB_STORAGE_DEBUG is not set
+# CONFIG_USB_STORAGE_DATAFAB is not set
+# CONFIG_USB_STORAGE_FREECOM is not set
+# CONFIG_USB_STORAGE_ISD200 is not set
+# CONFIG_USB_STORAGE_USBAT is not set
+# CONFIG_USB_STORAGE_SDDR09 is not set
+# CONFIG_USB_STORAGE_SDDR55 is not set
+# CONFIG_USB_STORAGE_JUMPSHOT is not set
+# CONFIG_USB_STORAGE_ALAUDA is not set
+# CONFIG_USB_STORAGE_ONETOUCH is not set
+# CONFIG_USB_STORAGE_KARMA is not set
+# CONFIG_USB_STORAGE_CYPRESS_ATACB is not set
+# CONFIG_USB_LIBUSUAL is not set
+
+#
+# USB Imaging devices
+#
+# CONFIG_USB_MDC800 is not set
+# CONFIG_USB_MICROTEK is not set
+
+#
+# USB port drivers
+#
+CONFIG_USB_SERIAL=m
+# CONFIG_USB_EZUSB is not set
+CONFIG_USB_SERIAL_GENERIC=y
+# CONFIG_USB_SERIAL_AIRCABLE is not set
+# CONFIG_USB_SERIAL_ARK3116 is not set
+# CONFIG_USB_SERIAL_BELKIN is not set
+# CONFIG_USB_SERIAL_CH341 is not set
+# CONFIG_USB_SERIAL_WHITEHEAT is not set
+# CONFIG_USB_SERIAL_DIGI_ACCELEPORT is not set
+# CONFIG_USB_SERIAL_CP210X is not set
+# CONFIG_USB_SERIAL_CYPRESS_M8 is not set
+# CONFIG_USB_SERIAL_EMPEG is not set
+# CONFIG_USB_SERIAL_FTDI_SIO is not set
+# CONFIG_USB_SERIAL_FUNSOFT is not set
+# CONFIG_USB_SERIAL_VISOR is not set
+# CONFIG_USB_SERIAL_IPAQ is not set
+# CONFIG_USB_SERIAL_IR is not set
+# CONFIG_USB_SERIAL_EDGEPORT is not set
+# CONFIG_USB_SERIAL_EDGEPORT_TI is not set
+# CONFIG_USB_SERIAL_GARMIN is not set
+# CONFIG_USB_SERIAL_IPW is not set
+# CONFIG_USB_SERIAL_IUU is not set
+# CONFIG_USB_SERIAL_KEYSPAN_PDA is not set
+# CONFIG_USB_SERIAL_KEYSPAN is not set
+# CONFIG_USB_SERIAL_KLSI is not set
+# CONFIG_USB_SERIAL_KOBIL_SCT is not set
+# CONFIG_USB_SERIAL_MCT_U232 is not set
+# CONFIG_USB_SERIAL_MOS7720 is not set
+# CONFIG_USB_SERIAL_MOS7840 is not set
+# CONFIG_USB_SERIAL_MOTOROLA is not set
+# CONFIG_USB_SERIAL_NAVMAN is not set
+# CONFIG_USB_SERIAL_PL2303 is not set
+# CONFIG_USB_SERIAL_OTI6858 is not set
+# CONFIG_USB_SERIAL_QUALCOMM is not set
+# CONFIG_USB_SERIAL_SPCP8X5 is not set
+# CONFIG_USB_SERIAL_HP4X is not set
+# CONFIG_USB_SERIAL_SAFE is not set
+# CONFIG_USB_SERIAL_SIEMENS_MPI is not set
+# CONFIG_USB_SERIAL_SIERRAWIRELESS is not set
+# CONFIG_USB_SERIAL_SYMBOL is not set
+# CONFIG_USB_SERIAL_TI is not set
+# CONFIG_USB_SERIAL_CYBERJACK is not set
+# CONFIG_USB_SERIAL_XIRCOM is not set
+CONFIG_USB_SERIAL_OPTION=m
+# CONFIG_USB_SERIAL_OMNINET is not set
+# CONFIG_USB_SERIAL_OPTICON is not set
+# CONFIG_USB_SERIAL_DEBUG is not set
+
+#
+# USB Miscellaneous drivers
+#
+# CONFIG_USB_EMI62 is not set
+# CONFIG_USB_EMI26 is not set
+# CONFIG_USB_ADUTUX is not set
+# CONFIG_USB_SEVSEG is not set
+# CONFIG_USB_RIO500 is not set
+# CONFIG_USB_LEGOTOWER is not set
+# CONFIG_USB_LCD is not set
+# CONFIG_USB_BERRY_CHARGE is not set
+# CONFIG_USB_LED is not set
+# CONFIG_USB_CYPRESS_CY7C63 is not set
+# CONFIG_USB_CYTHERM is not set
+# CONFIG_USB_IDMOUSE is not set
+# CONFIG_USB_FTDI_ELAN is not set
+# CONFIG_USB_APPLEDISPLAY is not set
+# CONFIG_USB_LD is not set
+# CONFIG_USB_TRANCEVIBRATOR is not set
+# CONFIG_USB_IOWARRIOR is not set
+# CONFIG_USB_TEST is not set
+# CONFIG_USB_ISIGHTFW is not set
+# CONFIG_USB_VST is not set
+# CONFIG_USB_GADGET is not set
+
+#
+# OTG and related infrastructure
+#
+# CONFIG_USB_GPIO_VBUS is not set
+# CONFIG_USB_ULPI is not set
+# CONFIG_NOP_USB_XCEIV is not set
+CONFIG_MMC=m
+CONFIG_MMC_DEBUG=y
+# CONFIG_MMC_UNSAFE_RESUME is not set
+
+#
+# MMC/SD/SDIO Card Drivers
+#
+CONFIG_MMC_BLOCK=m
+CONFIG_MMC_BLOCK_BOUNCE=y
+CONFIG_SDIO_UART=m
+# CONFIG_MMC_TEST is not set
+
+#
+# MMC/SD/SDIO Host Controller Drivers
+#
+CONFIG_MMC_PXA=m
+# CONFIG_MMC_SDHCI is not set
+# CONFIG_MMC_AT91 is not set
+# CONFIG_MMC_ATMELMCI is not set
+# CONFIG_MMC_SPI is not set
+# CONFIG_MEMSTICK is not set
+# CONFIG_NEW_LEDS is not set
+# CONFIG_ACCESSIBILITY is not set
+CONFIG_RTC_LIB=y
+CONFIG_RTC_CLASS=y
+CONFIG_RTC_HCTOSYS=y
+CONFIG_RTC_HCTOSYS_DEVICE="rtc0"
+# CONFIG_RTC_DEBUG is not set
+
+#
+# RTC interfaces
+#
+CONFIG_RTC_INTF_SYSFS=y
+CONFIG_RTC_INTF_PROC=y
+CONFIG_RTC_INTF_DEV=y
+# CONFIG_RTC_INTF_DEV_UIE_EMUL is not set
+# CONFIG_RTC_DRV_TEST is not set
+
+#
+# I2C RTC drivers
+#
+CONFIG_RTC_DRV_DS1307=y
+# CONFIG_RTC_DRV_DS1374 is not set
+# CONFIG_RTC_DRV_DS1672 is not set
+# CONFIG_RTC_DRV_MAX6900 is not set
+# CONFIG_RTC_DRV_RS5C372 is not set
+# CONFIG_RTC_DRV_ISL1208 is not set
+# CONFIG_RTC_DRV_X1205 is not set
+# CONFIG_RTC_DRV_PCF8563 is not set
+# CONFIG_RTC_DRV_PCF8583 is not set
+# CONFIG_RTC_DRV_M41T80 is not set
+# CONFIG_RTC_DRV_BQ32K is not set
+# CONFIG_RTC_DRV_S35390A is not set
+# CONFIG_RTC_DRV_FM3130 is not set
+# CONFIG_RTC_DRV_RX8581 is not set
+# CONFIG_RTC_DRV_RX8025 is not set
+
+#
+# SPI RTC drivers
+#
+# CONFIG_RTC_DRV_M41T94 is not set
+# CONFIG_RTC_DRV_DS1305 is not set
+# CONFIG_RTC_DRV_DS1390 is not set
+# CONFIG_RTC_DRV_MAX6902 is not set
+# CONFIG_RTC_DRV_R9701 is not set
+# CONFIG_RTC_DRV_RS5C348 is not set
+# CONFIG_RTC_DRV_DS3234 is not set
+# CONFIG_RTC_DRV_PCF2123 is not set
+
+#
+# Platform RTC drivers
+#
+# CONFIG_RTC_DRV_CMOS is not set
+# CONFIG_RTC_DRV_DS1286 is not set
+# CONFIG_RTC_DRV_DS1511 is not set
+# CONFIG_RTC_DRV_DS1553 is not set
+# CONFIG_RTC_DRV_DS1742 is not set
+# CONFIG_RTC_DRV_STK17TA8 is not set
+# CONFIG_RTC_DRV_M48T86 is not set
+# CONFIG_RTC_DRV_M48T35 is not set
+# CONFIG_RTC_DRV_M48T59 is not set
+# CONFIG_RTC_DRV_MSM6242 is not set
+# CONFIG_RTC_DRV_BQ4802 is not set
+# CONFIG_RTC_DRV_RP5C01 is not set
+# CONFIG_RTC_DRV_V3020 is not set
+
+#
+# on-CPU RTC drivers
+#
+# CONFIG_RTC_DRV_SA1100 is not set
+# CONFIG_RTC_DRV_PXA is not set
+# CONFIG_DMADEVICES is not set
+# CONFIG_AUXDISPLAY is not set
+# CONFIG_UIO is not set
+
+#
+# TI VLYNQ
+#
+# CONFIG_STAGING is not set
+
+#
+# File systems
+#
+# CONFIG_EXT2_FS is not set
+CONFIG_EXT3_FS=y
+# CONFIG_EXT3_DEFAULTS_TO_ORDERED is not set
+CONFIG_EXT3_FS_XATTR=y
+CONFIG_EXT3_FS_POSIX_ACL=y
+# CONFIG_EXT3_FS_SECURITY is not set
+# CONFIG_EXT4_FS is not set
+CONFIG_JBD=y
+CONFIG_FS_MBCACHE=y
+# CONFIG_REISERFS_FS is not set
+# CONFIG_JFS_FS is not set
+CONFIG_FS_POSIX_ACL=y
+# CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
+# CONFIG_OCFS2_FS is not set
+# CONFIG_BTRFS_FS is not set
+# CONFIG_NILFS2_FS is not set
+CONFIG_FILE_LOCKING=y
+CONFIG_FSNOTIFY=y
+# CONFIG_DNOTIFY is not set
+CONFIG_INOTIFY=y
+CONFIG_INOTIFY_USER=y
+# CONFIG_QUOTA is not set
+CONFIG_AUTOFS_FS=y
+CONFIG_AUTOFS4_FS=y
+CONFIG_FUSE_FS=m
+# CONFIG_CUSE is not set
+
+#
+# Caches
+#
+# CONFIG_FSCACHE is not set
+
+#
+# CD-ROM/DVD Filesystems
+#
+# CONFIG_ISO9660_FS is not set
+# CONFIG_UDF_FS is not set
+
+#
+# DOS/FAT/NT Filesystems
+#
+CONFIG_FAT_FS=m
+CONFIG_MSDOS_FS=m
+CONFIG_VFAT_FS=m
+CONFIG_FAT_DEFAULT_CODEPAGE=437
+CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1"
+# CONFIG_NTFS_FS is not set
+
+#
+# Pseudo filesystems
+#
+CONFIG_PROC_FS=y
+CONFIG_PROC_SYSCTL=y
+CONFIG_PROC_PAGE_MONITOR=y
+CONFIG_SYSFS=y
+CONFIG_TMPFS=y
+# CONFIG_TMPFS_POSIX_ACL is not set
+# CONFIG_HUGETLB_PAGE is not set
+CONFIG_CONFIGFS_FS=y
+CONFIG_MISC_FILESYSTEMS=y
+# CONFIG_ADFS_FS is not set
+# CONFIG_AFFS_FS is not set
+# CONFIG_ECRYPT_FS is not set
+# CONFIG_HFS_FS is not set
+# CONFIG_HFSPLUS_FS is not set
+# CONFIG_BEFS_FS is not set
+# CONFIG_BFS_FS is not set
+# CONFIG_EFS_FS is not set
+CONFIG_JFFS2_FS=y
+CONFIG_JFFS2_FS_DEBUG=0
+CONFIG_JFFS2_FS_WRITEBUFFER=y
+# CONFIG_JFFS2_FS_WBUF_VERIFY is not set
+# CONFIG_JFFS2_SUMMARY is not set
+# CONFIG_JFFS2_FS_XATTR is not set
+# CONFIG_JFFS2_COMPRESSION_OPTIONS is not set
+CONFIG_JFFS2_ZLIB=y
+# CONFIG_JFFS2_LZO is not set
+CONFIG_JFFS2_RTIME=y
+# CONFIG_JFFS2_RUBIN is not set
+CONFIG_UBIFS_FS=y
+# CONFIG_UBIFS_FS_XATTR is not set
+# CONFIG_UBIFS_FS_ADVANCED_COMPR is not set
+CONFIG_UBIFS_FS_LZO=y
+CONFIG_UBIFS_FS_ZLIB=y
+# CONFIG_UBIFS_FS_DEBUG is not set
+# CONFIG_CRAMFS is not set
+# CONFIG_SQUASHFS is not set
+# CONFIG_VXFS_FS is not set
+# CONFIG_MINIX_FS is not set
+# CONFIG_OMFS_FS is not set
+# CONFIG_HPFS_FS is not set
+# CONFIG_QNX4FS_FS is not set
+# CONFIG_ROMFS_FS is not set
+# CONFIG_SYSV_FS is not set
+# CONFIG_UFS_FS is not set
+CONFIG_NETWORK_FILESYSTEMS=y
+# CONFIG_NFS_FS is not set
+# CONFIG_NFSD is not set
+# CONFIG_SMB_FS is not set
+CONFIG_CIFS=m
+# CONFIG_CIFS_STATS is not set
+# CONFIG_CIFS_WEAK_PW_HASH is not set
+# CONFIG_CIFS_UPCALL is not set
+# CONFIG_CIFS_XATTR is not set
+# CONFIG_CIFS_DEBUG2 is not set
+# CONFIG_CIFS_DFS_UPCALL is not set
+# CONFIG_CIFS_EXPERIMENTAL is not set
+# CONFIG_NCP_FS is not set
+# CONFIG_CODA_FS is not set
+# CONFIG_AFS_FS is not set
+
+#
+# Partition Types
+#
+# CONFIG_PARTITION_ADVANCED is not set
+CONFIG_MSDOS_PARTITION=y
+CONFIG_NLS=y
+CONFIG_NLS_DEFAULT="iso8859-1"
+# CONFIG_NLS_CODEPAGE_437 is not set
+# CONFIG_NLS_CODEPAGE_737 is not set
+# CONFIG_NLS_CODEPAGE_775 is not set
+# CONFIG_NLS_CODEPAGE_850 is not set
+# CONFIG_NLS_CODEPAGE_852 is not set
+# CONFIG_NLS_CODEPAGE_855 is not set
+# CONFIG_NLS_CODEPAGE_857 is not set
+# CONFIG_NLS_CODEPAGE_860 is not set
+# CONFIG_NLS_CODEPAGE_861 is not set
+# CONFIG_NLS_CODEPAGE_862 is not set
+# CONFIG_NLS_CODEPAGE_863 is not set
+# CONFIG_NLS_CODEPAGE_864 is not set
+# CONFIG_NLS_CODEPAGE_865 is not set
+# CONFIG_NLS_CODEPAGE_866 is not set
+# CONFIG_NLS_CODEPAGE_869 is not set
+# CONFIG_NLS_CODEPAGE_936 is not set
+# CONFIG_NLS_CODEPAGE_950 is not set
+# CONFIG_NLS_CODEPAGE_932 is not set
+# CONFIG_NLS_CODEPAGE_949 is not set
+# CONFIG_NLS_CODEPAGE_874 is not set
+# CONFIG_NLS_ISO8859_8 is not set
+# CONFIG_NLS_CODEPAGE_1250 is not set
+# CONFIG_NLS_CODEPAGE_1251 is not set
+# CONFIG_NLS_ASCII is not set
+# CONFIG_NLS_ISO8859_1 is not set
+# CONFIG_NLS_ISO8859_2 is not set
+# CONFIG_NLS_ISO8859_3 is not set
+# CONFIG_NLS_ISO8859_4 is not set
+# CONFIG_NLS_ISO8859_5 is not set
+# CONFIG_NLS_ISO8859_6 is not set
+# CONFIG_NLS_ISO8859_7 is not set
+# CONFIG_NLS_ISO8859_9 is not set
+# CONFIG_NLS_ISO8859_13 is not set
+# CONFIG_NLS_ISO8859_14 is not set
+# CONFIG_NLS_ISO8859_15 is not set
+# CONFIG_NLS_KOI8_R is not set
+# CONFIG_NLS_KOI8_U is not set
+# CONFIG_NLS_UTF8 is not set
+# CONFIG_DLM is not set
+
+#
+# Kernel hacking
+#
+# CONFIG_PRINTK_TIME is not set
+CONFIG_ENABLE_WARN_DEPRECATED=y
+CONFIG_ENABLE_MUST_CHECK=y
+CONFIG_FRAME_WARN=1024
+# CONFIG_MAGIC_SYSRQ is not set
+# CONFIG_STRIP_ASM_SYMS is not set
+# CONFIG_UNUSED_SYMBOLS is not set
+# CONFIG_DEBUG_FS is not set
+# CONFIG_HEADERS_CHECK is not set
+# CONFIG_DEBUG_KERNEL is not set
+# CONFIG_SLUB_DEBUG_ON is not set
+# CONFIG_SLUB_STATS is not set
+CONFIG_DEBUG_BUGVERBOSE=y
+CONFIG_DEBUG_MEMORY_INIT=y
+CONFIG_FRAME_POINTER=y
+# CONFIG_RCU_CPU_STALL_DETECTOR is not set
+# CONFIG_LATENCYTOP is not set
+CONFIG_SYSCTL_SYSCALL_CHECK=y
+CONFIG_HAVE_FUNCTION_TRACER=y
+CONFIG_TRACING_SUPPORT=y
+# CONFIG_FTRACE is not set
+# CONFIG_SAMPLES is not set
+CONFIG_HAVE_ARCH_KGDB=y
+CONFIG_DEBUG_USER=y
+# CONFIG_OC_ETM is not set
+
+#
+# Security options
+#
+CONFIG_KEYS=y
+CONFIG_KEYS_DEBUG_PROC_KEYS=y
+CONFIG_SECURITY=y
+# CONFIG_SECURITYFS is not set
+# CONFIG_SECURITY_NETWORK is not set
+# CONFIG_SECURITY_PATH is not set
+# CONFIG_SECURITY_TOMOYO is not set
+# CONFIG_DEFAULT_SECURITY_SELINUX is not set
+# CONFIG_DEFAULT_SECURITY_SMACK is not set
+# CONFIG_DEFAULT_SECURITY_TOMOYO is not set
+CONFIG_DEFAULT_SECURITY_DAC=y
+CONFIG_DEFAULT_SECURITY=""
+CONFIG_CRYPTO=y
+
+#
+# Crypto core or helper
+#
+# CONFIG_CRYPTO_FIPS is not set
+CONFIG_CRYPTO_ALGAPI=y
+CONFIG_CRYPTO_ALGAPI2=y
+CONFIG_CRYPTO_HASH=m
+CONFIG_CRYPTO_HASH2=m
+CONFIG_CRYPTO_RNG=m
+CONFIG_CRYPTO_RNG2=m
+# CONFIG_CRYPTO_MANAGER is not set
+# CONFIG_CRYPTO_MANAGER2 is not set
+# CONFIG_CRYPTO_GF128MUL is not set
+# CONFIG_CRYPTO_NULL is not set
+# CONFIG_CRYPTO_CRYPTD is not set
+# CONFIG_CRYPTO_AUTHENC is not set
+# CONFIG_CRYPTO_TEST is not set
+
+#
+# Authenticated Encryption with Associated Data
+#
+# CONFIG_CRYPTO_CCM is not set
+# CONFIG_CRYPTO_GCM is not set
+# CONFIG_CRYPTO_SEQIV is not set
+
+#
+# Block modes
+#
+# CONFIG_CRYPTO_CBC is not set
+# CONFIG_CRYPTO_CTR is not set
+# CONFIG_CRYPTO_CTS is not set
+# CONFIG_CRYPTO_ECB is not set
+# CONFIG_CRYPTO_LRW is not set
+# CONFIG_CRYPTO_PCBC is not set
+# CONFIG_CRYPTO_XTS is not set
+
+#
+# Hash modes
+#
+# CONFIG_CRYPTO_HMAC is not set
+# CONFIG_CRYPTO_XCBC is not set
+# CONFIG_CRYPTO_VMAC is not set
+
+#
+# Digest
+#
+CONFIG_CRYPTO_CRC32C=m
+# CONFIG_CRYPTO_GHASH is not set
+# CONFIG_CRYPTO_MD4 is not set
+# CONFIG_CRYPTO_MD5 is not set
+# CONFIG_CRYPTO_MICHAEL_MIC is not set
+# CONFIG_CRYPTO_RMD128 is not set
+# CONFIG_CRYPTO_RMD160 is not set
+# CONFIG_CRYPTO_RMD256 is not set
+# CONFIG_CRYPTO_RMD320 is not set
+# CONFIG_CRYPTO_SHA1 is not set
+# CONFIG_CRYPTO_SHA256 is not set
+# CONFIG_CRYPTO_SHA512 is not set
+# CONFIG_CRYPTO_TGR192 is not set
+# CONFIG_CRYPTO_WP512 is not set
+
+#
+# Ciphers
+#
+CONFIG_CRYPTO_AES=m
+# CONFIG_CRYPTO_ANUBIS is not set
+# CONFIG_CRYPTO_ARC4 is not set
+# CONFIG_CRYPTO_BLOWFISH is not set
+# CONFIG_CRYPTO_CAMELLIA is not set
+# CONFIG_CRYPTO_CAST5 is not set
+# CONFIG_CRYPTO_CAST6 is not set
+# CONFIG_CRYPTO_DES is not set
+# CONFIG_CRYPTO_FCRYPT is not set
+# CONFIG_CRYPTO_KHAZAD is not set
+# CONFIG_CRYPTO_SALSA20 is not set
+# CONFIG_CRYPTO_SEED is not set
+# CONFIG_CRYPTO_SERPENT is not set
+# CONFIG_CRYPTO_TEA is not set
+# CONFIG_CRYPTO_TWOFISH is not set
+
+#
+# Compression
+#
+CONFIG_CRYPTO_DEFLATE=y
+# CONFIG_CRYPTO_ZLIB is not set
+CONFIG_CRYPTO_LZO=y
+
+#
+# Random Number Generation
+#
+CONFIG_CRYPTO_ANSI_CPRNG=m
+CONFIG_CRYPTO_HW=y
+# CONFIG_BINARY_PRINTF is not set
+
+#
+# Library routines
+#
+CONFIG_BITREVERSE=y
+CONFIG_GENERIC_FIND_LAST_BIT=y
+CONFIG_CRC_CCITT=m
+CONFIG_CRC16=y
+# CONFIG_CRC_T10DIF is not set
+CONFIG_CRC_ITU_T=m
+CONFIG_CRC32=y
+CONFIG_CRC7=m
+CONFIG_LIBCRC32C=m
+CONFIG_ZLIB_INFLATE=y
+CONFIG_ZLIB_DEFLATE=y
+CONFIG_LZO_COMPRESS=y
+CONFIG_LZO_DECOMPRESS=y
+CONFIG_HAS_IOMEM=y
+CONFIG_HAS_IOPORT=y
+CONFIG_HAS_DMA=y
+CONFIG_NLATTR=y
diff -uNrp linux-2.6.33-rc4/arch/arm/mach-pxa/Kconfig linux-embedian-2.6.33-rc4/arch/arm/mach-pxa/Kconfig
--- linux-2.6.33-rc4/arch/arm/mach-pxa/Kconfig 2010-01-13 17:06:11.000000000 +0200
+++ linux-embedian-2.6.33-rc4/arch/arm/mach-pxa/Kconfig 2010-01-13 17:00:13.000000000 +0200
@@ -115,6 +115,11 @@ config MACH_CM_X300
select CPU_PXA310
select HAVE_PWM
+config MACH_CAPC7117
+ bool "Embedian CAPC-7117 evaluation kit based on the MXM-8x10 CoM"
+ select CPU_PXA320
+ select PXA3xx
+
config ARCH_GUMSTIX
bool "Gumstix XScale 255 boards"
select PXA25x
diff -uNrp linux-2.6.33-rc4/arch/arm/mach-pxa/Kconfig.orig linux-embedian-2.6.33-rc4/arch/arm/mach-pxa/Kconfig.orig
--- linux-2.6.33-rc4/arch/arm/mach-pxa/Kconfig.orig 1970-01-01 02:00:00.000000000 +0200
+++ linux-embedian-2.6.33-rc4/arch/arm/mach-pxa/Kconfig.orig 2010-01-13 16:47:30.000000000 +0200
@@ -0,0 +1,646 @@
+if ARCH_PXA
+
+menu "Intel PXA2xx/PXA3xx Implementations"
+
+comment "Intel/Marvell Dev Platforms (sorted by hardware release time)"
+
+config ARCH_LUBBOCK
+ bool "Intel DBPXA250 Development Platform (aka Lubbock)"
+ select PXA25x
+ select SA1111
+ select PXA_HAVE_BOARD_IRQS
+
+config MACH_MAINSTONE
+ bool "Intel HCDDBBVA0 Development Platform (aka Mainstone)"
+ select PXA27x
+ select HAVE_PWM
+ select PXA_HAVE_BOARD_IRQS
+
+config MACH_ZYLONITE
+ bool
+ select PXA3xx
+ select PXA_SSP
+ select HAVE_PWM
+ select PXA_HAVE_BOARD_IRQS
+
+config MACH_ZYLONITE300
+ bool "PXA3xx Development Platform (aka Zylonite) PXA300/310"
+ select CPU_PXA300
+ select CPU_PXA310
+ select MACH_ZYLONITE
+
+config MACH_ZYLONITE320
+ bool "PXA3xx Development Platform (aka Zylonite) PXA320"
+ select CPU_PXA320
+ select MACH_ZYLONITE
+
+config MACH_LITTLETON
+ bool "PXA3xx Form Factor Platform (aka Littleton)"
+ select PXA3xx
+ select CPU_PXA300
+ select CPU_PXA310
+ select PXA_SSP
+
+config MACH_TAVOREVB
+ bool "PXA930 Evaluation Board (aka TavorEVB)"
+ select PXA3xx
+ select CPU_PXA930
+
+config MACH_SAAR
+ bool "PXA930 Handheld Platform (aka SAAR)"
+ select PXA3xx
+ select CPU_PXA930
+
+comment "Third Party Dev Platforms (sorted by vendor name)"
+
+config ARCH_PXA_IDP
+ bool "Accelent Xscale IDP"
+ select PXA25x
+
+config ARCH_VIPER
+ bool "Arcom/Eurotech VIPER SBC"
+ select PXA25x
+ select ISA
+ select I2C_GPIO
+ select HAVE_PWM
+ select PXA_HAVE_BOARD_IRQS
+ select PXA_HAVE_ISA_IRQS
+ select ARCOM_PCMCIA
+
+config MACH_ARCOM_ZEUS
+ bool "Arcom/Eurotech ZEUS SBC"
+ select PXA27x
+ select ISA
+ select PXA_HAVE_BOARD_IRQS
+ select PXA_HAVE_ISA_IRQS
+ select ARCOM_PCMCIA
+
+config MACH_BALLOON3
+ bool "Balloon 3 board"
+ select PXA27x
+ select IWMMXT
+ select PXA_HAVE_BOARD_IRQS
+
+config MACH_CSB726
+ bool "Enable Cogent CSB726 System On a Module"
+ select PXA27x
+ select IWMMXT
+ help
+ Say Y here if you intend to run this kernel on a Cogent
+ CSB726 System On Module.
+
+config CSB726_CSB701
+ bool "Enable support for CSB701 baseboard"
+ depends on MACH_CSB726
+
+config MACH_ARMCORE
+ bool "CompuLab CM-X255/CM-X270 modules"
+ select PXA27x
+ select IWMMXT
+ select PXA25x
+ select PXA_SSP
+
+config MACH_EM_X270
+ bool "CompuLab EM-x270 platform"
+ select PXA27x
+
+config MACH_EXEDA
+ bool "CompuLab eXeda platform"
+ select PXA27x
+
+config MACH_CM_X300
+ bool "CompuLab CM-X300 modules"
+ select PXA3xx
+ select CPU_PXA300
+ select CPU_PXA310
+ select HAVE_PWM
+
+config ARCH_GUMSTIX
+ bool "Gumstix XScale 255 boards"
+ select PXA25x
+ help
+ Say Y here if you intend to run this kernel on
+ Basix, Connex, ws-200ax, ws-400ax systems
+
+choice
+ prompt "Gumstix Carrier/Expansion Board"
+ depends on ARCH_GUMSTIX
+
+config GUMSTIX_AM200EPD
+ bool "Enable AM200EPD board support"
+
+config GUMSTIX_AM300EPD
+ bool "Enable AM300EPD board support"
+
+endchoice
+
+config MACH_INTELMOTE2
+ bool "Intel Mote 2 Platform"
+ select PXA27x
+ select IWMMXT
+ select PXA_HAVE_BOARD_IRQS
+
+config MACH_STARGATE2
+ bool "Intel Stargate 2 Platform"
+ select PXA27x
+ select IWMMXT
+ select PXA_HAVE_BOARD_IRQS
+
+config MACH_XCEP
+ bool "Iskratel Electronics XCEP"
+ select PXA25x
+ select MTD
+ select MTD_PARTITIONS
+ select MTD_PHYSMAP
+ select MTD_CFI_INTELEXT
+ select MTD_CFI
+ select MTD_CHAR
+ select SMC91X
+ select PXA_SSP
+ help
+ PXA255 based Single Board Computer with SMC 91C111 ethernet chip and 64 MB of flash.
+ Tuned for usage in Libera instruments for particle accelerators.
+
+config TRIZEPS_PXA
+ bool "PXA based Keith und Koep Trizeps DIMM-Modules"
+
+config MACH_TRIZEPS4
+ bool "Keith und Koep Trizeps4 DIMM-Module"
+ depends on TRIZEPS_PXA
+ select TRIZEPS_PCMCIA
+ select PXA27x
+
+config MACH_TRIZEPS4WL
+ bool "Keith und Koep Trizeps4-WL DIMM-Module"
+ depends on TRIZEPS_PXA
+ select TRIZEPS_PCMCIA
+ select PXA27x
+ select PXA_SSP
+
+choice
+ prompt "Select base board for Trizeps module"
+ depends on TRIZEPS_PXA
+
+config MACH_TRIZEPS_CONXS
+ bool "ConXS Eval Board"
+
+config MACH_TRIZEPS_UCONXS
+ bool "uConXS Eval Board"
+
+config MACH_TRIZEPS_ANY
+ bool "another Board"
+
+endchoice
+
+config ARCOM_PCMCIA
+ bool
+ help
+ Generic option for Arcom Viper/Zeus PCMCIA
+
+config TRIZEPS_PCMCIA
+ bool
+ help
+ Enable PCMCIA support for Trizeps modules
+
+config MACH_LOGICPD_PXA270
+ bool "LogicPD PXA270 Card Engine Development Platform"
+ select PXA27x
+ select HAVE_PWM
+ select PXA_HAVE_BOARD_IRQS
+
+config MACH_PCM027
+ bool "Phytec phyCORE-PXA270 CPU module (PCM-027)"
+ select PXA27x
+ select IWMMXT
+ select PXA_SSP
+ select PXA_HAVE_BOARD_IRQS
+
+config MACH_PCM990_BASEBOARD
+ bool "PHYTEC PCM-990 development board"
+ select HAVE_PWM
+ depends on MACH_PCM027
+
+choice
+ prompt "display on pcm990"
+ depends on MACH_PCM990_BASEBOARD
+
+config PCM990_DISPLAY_SHARP
+ bool "sharp lq084v1dg21 stn display"
+
+config PCM990_DISPLAY_NEC
+ bool "nec nl6448bc20_18d tft display"
+
+config PCM990_DISPLAY_NONE
+ bool "no display"
+
+endchoice
+
+config MACH_COLIBRI
+ bool "Toradex Colibri PXA270"
+ select PXA27x
+
+config MACH_COLIBRI300
+ bool "Toradex Colibri PXA300/310"
+ select PXA3xx
+ select CPU_PXA300
+ select CPU_PXA310
+
+config MACH_COLIBRI320
+ bool "Toradex Colibri PXA320"
+ select PXA3xx
+ select CPU_PXA320
+
+comment "End-user Products (sorted by vendor name)"
+
+config MACH_H4700
+ bool "HP iPAQ hx4700"
+ select PXA27x
+ select IWMMXT
+ select PXA_SSP
+ select HAVE_PWM
+ select PXA_HAVE_BOARD_IRQS
+
+config MACH_H5000
+ bool "HP iPAQ h5000"
+ select PXA25x
+
+config MACH_HIMALAYA
+ bool "HTC Himalaya Support"
+ select CPU_PXA26x
+ select FB_W100
+
+config MACH_MAGICIAN
+ bool "Enable HTC Magician Support"
+ select PXA27x
+ select IWMMXT
+ select PXA_SSP
+ select HAVE_PWM
+ select PXA_HAVE_BOARD_IRQS
+
+config MACH_MIOA701
+ bool "Mitac Mio A701 Support"
+ select PXA27x
+ select IWMMXT
+ select HAVE_PWM
+ select GPIO_SYSFS
+ help
+ Say Y here if you intend to run this kernel on a
+ MIO A701. Currently there is only basic support
+ for this PDA.
+
+config PXA_EZX
+ bool "Motorola EZX Platform"
+ select PXA27x
+ select IWMMXT
+ select HAVE_PWM
+ select PXA_HAVE_BOARD_IRQS
+
+config MACH_EZX_A780
+ bool "Motorola EZX A780"
+ default y
+ depends on PXA_EZX
+
+config MACH_EZX_E680
+ bool "Motorola EZX E680"
+ default y
+ depends on PXA_EZX
+
+config MACH_EZX_A1200
+ bool "Motorola EZX A1200"
+ default y
+ depends on PXA_EZX
+
+config MACH_EZX_A910
+ bool "Motorola EZX A910"
+ default y
+ depends on PXA_EZX
+
+config MACH_EZX_E6
+ bool "Motorola EZX E6"
+ default y
+ depends on PXA_EZX
+
+config MACH_EZX_E2
+ bool "Motorola EZX E2"
+ default y
+ depends on PXA_EZX
+
+config MACH_MP900C
+ bool "Nec Mobilepro 900/c"
+ select PXA25x
+
+config ARCH_PXA_PALM
+ bool "PXA based Palm PDAs"
+ select HAVE_PWM
+
+config MACH_PALMTE2
+ bool "Palm Tungsten|E2"
+ default y
+ depends on ARCH_PXA_PALM
+ select PXA25x
+ help
+ Say Y here if you intend to run this kernel on a Palm Tungsten|E2
+ handheld computer.
+
+config MACH_PALMTC
+ bool "Palm Tungsten|C"
+ default y
+ depends on ARCH_PXA_PALM
+ select PXA25x
+ help
+ Say Y here if you intend to run this kernel on a Palm Tungsten|C
+ handheld computer.
+
+config MACH_PALMT5
+ bool "Palm Tungsten|T5"
+ default y
+ depends on ARCH_PXA_PALM
+ select PXA27x
+ select IWMMXT
+ help
+ Say Y here if you intend to run this kernel on a Palm Tungsten|T5
+ handheld computer.
+
+config MACH_PALMTX
+ bool "Palm T|X"
+ default y
+ depends on ARCH_PXA_PALM
+ select PXA27x
+ select IWMMXT
+ help
+ Say Y here if you intend to run this kernel on a Palm T|X
+ handheld computer.
+
+config MACH_PALMZ72
+ bool "Palm Zire 72"
+ default y
+ depends on ARCH_PXA_PALM
+ select PXA27x
+ select IWMMXT
+ help
+ Say Y here if you intend to run this kernel on Palm Zire 72
+ handheld computer.
+
+config MACH_PALMLD
+ bool "Palm LifeDrive"
+ default y
+ depends on ARCH_PXA_PALM
+ select PXA27x
+ select IWMMXT
+ help
+ Say Y here if you intend to run this kernel on a Palm LifeDrive
+ handheld computer.
+
+config PALM_TREO
+ bool
+ depends on ARCH_PXA_PALM
+
+config MACH_CENTRO
+ bool "Palm Centro 685 (GSM)"
+ default y
+ depends on ARCH_PXA_PALM
+ select PXA27x
+ select IWMMXT
+ select PALM_TREO
+ help
+ Say Y here if you intend to run this kernel on Palm Centro 685 (GSM)
+ smartphone.
+
+config MACH_TREO680
+ bool "Palm Treo 680"
+ default y
+ depends on ARCH_PXA_PALM
+ select PXA27x
+ select IWMMXT
+ select PALM_TREO
+ help
+ Say Y here if you intend to run this kernel on Palm Treo 680
+ smartphone.
+
+config PXA_SHARPSL
+ bool "SHARP Zaurus SL-5600, SL-C7xx and SL-Cxx00 Models"
+ select SHARP_SCOOP
+ select SHARP_PARAM
+ help
+ Say Y here if you intend to run this kernel on a
+ Sharp Zaurus SL-5600 (Poodle), SL-C700 (Corgi),
+ SL-C750 (Shepherd), SL-C760 (Husky), SL-C1000 (Akita),
+ SL-C3000 (Spitz), SL-C3100 (Borzoi) or SL-C6000x (Tosa)
+ handheld computer.
+
+config SHARPSL_PM
+ bool
+ select APM_EMULATION
+
+config CORGI_SSP_DEPRECATED
+ bool
+ select PXA_SSP
+ help
+ This option will include corgi_ssp.c and corgi_lcd.c
+ that corgi_ts.c and other legacy drivers (corgi_bl.c
+ and sharpsl_pm.c) may depend on.
+
+config MACH_POODLE
+ bool "Enable Sharp SL-5600 (Poodle) Support"
+ depends on PXA_SHARPSL
+ select PXA25x
+ select SHARP_LOCOMO
+ select PXA_SSP
+
+config MACH_CORGI
+ bool "Enable Sharp SL-C700 (Corgi) Support"
+ depends on PXA_SHARPSL
+ select PXA25x
+ select PXA_SHARP_C7xx
+
+config MACH_SHEPHERD
+ bool "Enable Sharp SL-C750 (Shepherd) Support"
+ depends on PXA_SHARPSL
+ select PXA25x
+ select PXA_SHARP_C7xx
+
+config MACH_HUSKY
+ bool "Enable Sharp SL-C760 (Husky) Support"
+ depends on PXA_SHARPSL
+ select PXA25x
+ select PXA_SHARP_C7xx
+
+config MACH_AKITA
+ bool "Enable Sharp SL-1000 (Akita) Support"
+ depends on PXA_SHARPSL
+ select PXA27x
+ select PXA_SHARP_Cxx00
+ select MACH_SPITZ
+ select I2C
+ select I2C_PXA
+
+config MACH_SPITZ
+ bool "Enable Sharp Zaurus SL-3000 (Spitz) Support"
+ depends on PXA_SHARPSL
+ select PXA27x
+ select PXA_SHARP_Cxx00
+
+config MACH_BORZOI
+ bool "Enable Sharp Zaurus SL-3100 (Borzoi) Support"
+ depends on PXA_SHARPSL
+ select PXA27x
+ select PXA_SHARP_Cxx00
+
+config MACH_TOSA
+ bool "Enable Sharp SL-6000x (Tosa) Support"
+ depends on PXA_SHARPSL
+ select PXA25x
+ select PXA_HAVE_BOARD_IRQS
+
+config ARCH_PXA_ESERIES
+ bool "PXA based Toshiba e-series PDAs"
+ select PXA25x
+ select PXA_HAVE_BOARD_IRQS
+
+config MACH_E330
+ bool "Toshiba e330"
+ default y
+ depends on ARCH_PXA_ESERIES
+ help
+ Say Y here if you intend to run this kernel on a Toshiba
+ e330 family PDA.
+
+config MACH_E350
+ bool "Toshiba e350"
+ default y
+ depends on ARCH_PXA_ESERIES
+ help
+ Say Y here if you intend to run this kernel on a Toshiba
+ e350 family PDA.
+
+config MACH_E740
+ bool "Toshiba e740"
+ default y
+ depends on ARCH_PXA_ESERIES
+ select FB_W100
+ help
+ Say Y here if you intend to run this kernel on a Toshiba
+ e740 family PDA.
+
+config MACH_E750
+ bool "Toshiba e750"
+ default y
+ depends on ARCH_PXA_ESERIES
+ select FB_W100
+ help
+ Say Y here if you intend to run this kernel on a Toshiba
+ e750 family PDA.
+
+config MACH_E400
+ bool "Toshiba e400"
+ default y
+ depends on ARCH_PXA_ESERIES
+ help
+ Say Y here if you intend to run this kernel on a Toshiba
+ e400 family PDA.
+
+config MACH_E800
+ bool "Toshiba e800"
+ default y
+ depends on ARCH_PXA_ESERIES
+ select FB_W100
+ help
+ Say Y here if you intend to run this kernel on a Toshiba
+ e800 family PDA.
+
+endmenu
+
+config PXA25x
+ bool
+ select CPU_XSCALE
+ help
+ Select code specific to PXA21x/25x/26x variants
+
+config PXA27x
+ bool
+ select CPU_XSCALE
+ help
+ Select code specific to PXA27x variants
+
+config CPU_PXA26x
+ bool
+ select PXA25x
+ help
+ Select code specific to PXA26x (codename Dalhart)
+
+config PXA3xx
+ bool
+ select CPU_XSC3
+ help
+ Select code specific to PXA3xx variants
+
+config CPU_PXA300
+ bool
+ select PXA3xx
+ help
+ PXA300 (codename Monahans-L)
+
+config CPU_PXA310
+ bool
+ select CPU_PXA300
+ help
+ PXA310 (codename Monahans-LV)
+
+config CPU_PXA320
+ bool
+ select PXA3xx
+ help
+ PXA320 (codename Monahans-P)
+
+config CPU_PXA930
+ bool
+ select PXA3xx
+ help
+ PXA930 (codename Tavor-P)
+
+config CPU_PXA935
+ bool
+ select CPU_PXA930
+ help
+ PXA935 (codename Tavor-P65)
+
+config CPU_PXA950
+ bool
+ select CPU_PXA930
+ help
+ PXA950 (codename Tavor-PV2)
+
+config PXA_SHARP_C7xx
+ bool
+ select PXA_SSP
+ select SHARPSL_PM
+ help
+ Enable support for all Sharp C7xx models
+
+config PXA_SHARP_Cxx00
+ bool
+ select PXA_SSP
+ select SHARPSL_PM
+ help
+ Enable common support for Sharp Cxx00 models
+
+config PXA_SSP
+ tristate
+ help
+ Enable support for PXA2xx SSP ports
+
+config TOSA_BT
+ tristate "Control the state of built-in bluetooth chip on Sharp SL-6000"
+ depends on MACH_TOSA
+ select RFKILL
+ help
+ This is a simple driver that is able to control
+ the state of built in bluetooth chip on tosa.
+
+config PXA_HAVE_BOARD_IRQS
+ bool
+
+config PXA_HAVE_ISA_IRQS
+ bool
+
+endif
diff -uNrp linux-2.6.33-rc4/arch/arm/mach-pxa/Makefile linux-embedian-2.6.33-rc4/arch/arm/mach-pxa/Makefile
--- linux-2.6.33-rc4/arch/arm/mach-pxa/Makefile 2010-01-13 17:06:11.000000000 +0200
+++ linux-embedian-2.6.33-rc4/arch/arm/mach-pxa/Makefile 2010-01-13 17:00:13.000000000 +0200
@@ -48,6 +48,7 @@ obj-$(CONFIG_MACH_ARMCORE) += cm-x2xx-pc
endif
obj-$(CONFIG_MACH_EM_X270) += em-x270.o
obj-$(CONFIG_MACH_CM_X300) += cm-x300.o
+obj-$(CONFIG_MACH_CAPC7117) += capc7117.o mxm8x10.o
obj-$(CONFIG_ARCH_GUMSTIX) += gumstix.o
obj-$(CONFIG_GUMSTIX_AM200EPD) += am200epd.o
obj-$(CONFIG_GUMSTIX_AM300EPD) += am300epd.o
diff -uNrp linux-2.6.33-rc4/arch/arm/mach-pxa/capc7117.c linux-embedian-2.6.33-rc4/arch/arm/mach-pxa/capc7117.c
--- linux-2.6.33-rc4/arch/arm/mach-pxa/capc7117.c 1970-01-01 02:00:00.000000000 +0200
+++ linux-embedian-2.6.33-rc4/arch/arm/mach-pxa/capc7117.c 2010-01-13 17:00:13.000000000 +0200
@@ -0,0 +1,180 @@
+/*
+ * linux/arch/arm/mach-pxa/capc7117.c
+ *
+ * Support for the Embedian CAPC-7117 Evaluation Kit
+ * based on the Embedian MXM-8x10 Computer on Module
+ *
+ * Copyright (C) 2009 Embedian Inc.
+ * Copyright (C) 2009 TMT Services & Supplies (Pty) Ltd.
+ *
+ * 2007-09-04: eric miao <eric.y.miao at gmail.com>
+ * rewrite to align with latest kernel
+ *
+ * 2010-01-09: Edwin Peer <epeer at tmtservices.co.za>
+ * Hennie van der Merwe <hvdmerwe at tmtservices.co.za>
+ * rework for upstream merge
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/irq.h>
+#include <linux/platform_device.h>
+#include <linux/ata_platform.h>
+#include <linux/serial_8250.h>
+
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+#include <mach/gpio.h>
+#include <mach/mfp-pxa320.h>
+#include <mach/mxm8x10.h>
+
+#include "generic.h"
+
+/* IDE (PATA) Support */
+static struct pata_platform_info pata_platform_data = {
+ .ioport_shift = 1,
+};
+
+static struct resource capc7117_ide_resources[] = {
+ [0] = {
+ .start = 0x11000020,
+ .end = 0x1100003f,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = 0x1100001c,
+ .end = 0x1100001c,
+ .flags = IORESOURCE_MEM,
+ },
+ [2] = {
+ .start = 0,
+ .end = 0,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+struct platform_device capc7117_ide_device = {
+ .name = "pata_platform",
+ .num_resources = ARRAY_SIZE(capc7117_ide_resources),
+ .resource = capc7117_ide_resources,
+ .dev = {
+ .platform_data = &pata_platform_data,
+ .coherent_dma_mask = ~0, /* grumble */
+ },
+};
+
+int capc7117_ide_mach_init(void)
+{
+ return 0;
+}
+EXPORT_SYMBOL(capc7117_ide_mach_init);
+
+static void __init capc7117_ide_init(void)
+{
+ pxa3xx_mfp_write(MFP_PIN_GPIO76, 0xa0c0); /* EXT_IRQ3 */
+
+ capc7117_ide_resources[2].start =
+ gpio_to_irq(mfp_to_gpio(MFP_PIN_GPIO76));
+ capc7117_ide_resources[2].end =
+ gpio_to_irq(mfp_to_gpio(MFP_PIN_GPIO76));
+ set_irq_type(capc7117_ide_resources[2].start, IRQ_TYPE_EDGE_RISING);
+ platform_device_register(&capc7117_ide_device);
+}
+
+/* TI16C752 UART support */
+#define TI16C752_FLAGS (UPF_BOOT_AUTOCONF | \
+ UPF_IOREMAP | \
+ UPF_BUGGY_UART | \
+ UPF_SKIP_TEST)
+#define TI16C752_UARTCLK (22118400)
+static struct plat_serial8250_port ti16c752_platform_data[] = {
+ [0] = {
+ .mapbase = 0x14000000,
+ .irq = gpio_to_irq(mfp_to_gpio(MFP_PIN_GPIO78)),
+ .flags = TI16C752_FLAGS,
+ .iotype = UPIO_MEM,
+ .regshift = 1,
+ .uartclk = TI16C752_UARTCLK,
+ },
+ [1] = {
+ .mapbase = 0x14000040,
+ .irq = gpio_to_irq(mfp_to_gpio(MFP_PIN_GPIO79)),
+ .flags = TI16C752_FLAGS,
+ .iotype = UPIO_MEM,
+ .regshift = 1,
+ .uartclk = TI16C752_UARTCLK,
+ },
+ [2] = {
+ .mapbase = 0x14000080,
+ .irq = gpio_to_irq(mfp_to_gpio(MFP_PIN_GPIO80)),
+ .flags = TI16C752_FLAGS,
+ .iotype = UPIO_MEM,
+ .regshift = 1,
+ .uartclk = TI16C752_UARTCLK,
+ },
+ [3] = {
+ .mapbase = 0x140000c0,
+ .irq = gpio_to_irq(mfp_to_gpio(MFP_PIN_GPIO81)),
+ .flags = TI16C752_FLAGS,
+ .iotype = UPIO_MEM,
+ .regshift = 1,
+ .uartclk = TI16C752_UARTCLK,
+ },
+ [4] = {
+ .flags = 0,
+ },
+};
+
+static struct platform_device ti16c752_device = {
+ .name = "serial8250",
+ .id = PLAT8250_DEV_PLATFORM,
+ .dev = {
+ .platform_data = ti16c752_platform_data,
+ },
+};
+
+static void __init capc7117_uarts_init(void)
+{
+ int i;
+
+ pxa3xx_mfp_write(MFP_PIN_GPIO78, 0xa090); /* EXT_IRQ5 */
+ pxa3xx_mfp_write(MFP_PIN_GPIO79, 0xa090); /* EXT_IRQ6 */
+ pxa3xx_mfp_write(MFP_PIN_GPIO80, 0xa090); /* EXT_IRQ7 */
+ pxa3xx_mfp_write(MFP_PIN_GPIO81, 0xa090); /* EXT_IRQ8 */
+
+ for (i = 0; i < 4; i++)
+ set_irq_type(ti16c752_platform_data[i].irq,
+ IRQ_TYPE_EDGE_RISING);
+
+ platform_device_register(&ti16c752_device);
+}
+
+static void __init capc7117_init(void)
+{
+ if (cpu_is_pxa320()) {
+ mxm_8x10_barebones_init();
+
+ mxm_8x10_lcd_init();
+ mxm_8x10_ac97_init();
+ mxm_8x10_usb_host_init();
+ mxm_8x10_mmc_init();
+
+ capc7117_uarts_init();
+ capc7117_ide_init();
+ } else {
+ panic("Unsupported processor. Platform must be pxa320\n");
+ }
+}
+
+MACHINE_START(CAPC7117,
+ "Embedian CAPC-7117 evaluation kit based on the MXM-8x10 CoM")
+ .phys_io = 0x40000000,
+ .boot_params = 0xa0000100,
+ .io_pg_offst = (io_p2v(0x40000000) >> 18) & 0xfffc,
+ .map_io = pxa_map_io,
+ .init_irq = pxa3xx_init_irq,
+ .timer = &pxa_timer,
+ .init_machine = capc7117_init,
+MACHINE_END
diff -uNrp linux-2.6.33-rc4/arch/arm/mach-pxa/include/mach/mxm8x10.h linux-embedian-2.6.33-rc4/arch/arm/mach-pxa/include/mach/mxm8x10.h
--- linux-2.6.33-rc4/arch/arm/mach-pxa/include/mach/mxm8x10.h 1970-01-01 02:00:00.000000000 +0200
+++ linux-embedian-2.6.33-rc4/arch/arm/mach-pxa/include/mach/mxm8x10.h 2010-01-13 17:00:13.000000000 +0200
@@ -0,0 +1,28 @@
+#ifndef __MACH_MXM_8X10_H
+#define __MACH_MXM_8X10_H
+
+#define MXM_8X10_ETH_PHYS 0x13000000
+
+#define NAND_MMIO_START 0x43100000
+#define NAND_MMIO_END 0x43100080
+
+#define EXT_GPIO(x) (128 + (x))
+
+struct platform_mmc_slot {
+ int gpio_cd;
+ int gpio_wp;
+};
+
+extern void mxm_8x10_mmc_init(void);
+extern void mxm_8x10_usb_host_init(void);
+extern void mxm_8x10_ac97_init(void);
+extern void mxm_8x10_nand_init(void);
+extern void mxm_8x10_ethernet_init(void);
+extern void mxm_8x10_ide_init(void);
+extern void mxm_8x10_uart_init(void);
+extern void mxm_8x10_lcd_init(void);
+extern void mxm_8x10_i2c_init(void);
+
+extern void mxm_8x10_barebones_init(void);
+
+#endif /* __MACH_MXM_8X10_H */
diff -uNrp linux-2.6.33-rc4/arch/arm/mach-pxa/mxm8x10.c linux-embedian-2.6.33-rc4/arch/arm/mach-pxa/mxm8x10.c
--- linux-2.6.33-rc4/arch/arm/mach-pxa/mxm8x10.c 1970-01-01 02:00:00.000000000 +0200
+++ linux-embedian-2.6.33-rc4/arch/arm/mach-pxa/mxm8x10.c 2010-01-13 17:00:13.000000000 +0200
@@ -0,0 +1,842 @@
+/*
+ * linux/arch/arm/mach-pxa/mxm8x10.c
+ *
+ * Support for the Embedian MXM-8x10 Computer on Module
+ *
+ * Copyright (C) 2006 Marvell International Ltd.
+ * Copyright (C) 2009 Embedian Inc.
+ * Copyright (C) 2009 TMT Services & Supplies (Pty) Ltd.
+ *
+ * 2007-09-04: eric miao <eric.y.miao at gmail.com>
+ * rewrite to align with latest kernel
+ *
+ * 2010-01-09: Edwin Peer <epeer at tmtservices.co.za>
+ * Hennie van der Merwe <hvdmerwe at tmtservices.co.za>
+ * rework for upstream merge
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/serial_8250.h>
+#include <linux/dm9000.h>
+
+#include <plat/i2c.h>
+#include <plat/pxa3xx_nand.h>
+
+#include <mach/gpio.h>
+#include <mach/pxafb.h>
+#include <mach/mmc.h>
+#include <mach/mfp-pxa320.h>
+#include <mach/ohci.h>
+#include <mach/pxa3xx-regs.h>
+
+#include <mach/mxm8x10.h>
+
+#include "devices.h"
+#include "generic.h"
+
+/* GPIO pin definition
+
+External device stuff - Leave unconfigured for now...
+---------------------
+GPIO0 - DREQ (External DMA Request)
+GPIO3 - nGCS2 (External Chip Select) Where is nGCS0; nGCS1; nGCS4; nGCS5 ?
+GPIO4 - nGCS3
+GPIO15 - EXT_GPIO1
+GPIO16 - EXT_GPIO2
+GPIO17 - EXT_GPIO3
+GPIO24 - EXT_GPIO4
+GPIO25 - EXT_GPIO5
+GPIO26 - EXT_GPIO6
+GPIO27 - EXT_GPIO7
+GPIO28 - EXT_GPIO8
+GPIO29 - EXT_GPIO9
+GPIO30 - EXT_GPIO10
+GPIO31 - EXT_GPIO11
+GPIO57 - EXT_GPIO12
+GPIO74 - EXT_IRQ1
+GPIO75 - EXT_IRQ2
+GPIO76 - EXT_IRQ3
+GPIO77 - EXT_IRQ4
+GPIO78 - EXT_IRQ5
+GPIO79 - EXT_IRQ6
+GPIO80 - EXT_IRQ7
+GPIO81 - EXT_IRQ8
+GPIO87 - VCCIO_PWREN (External Device PWREN)
+
+Dallas 1-Wire - Leave unconfigured for now...
+-------------
+GPIO0_2 - DS - 1Wire
+
+Ethernet
+--------
+GPIO1 - DM9000 PWR
+GPIO9 - DM9K_nIRQ
+GPIO36 - DM9K_RESET
+
+Keypad - Leave unconfigured by for now...
+------
+GPIO1_2 - KP_DKIN0
+GPIO5_2 - KP_MKOUT7
+GPIO82 - KP_DKIN1
+GPIO85 - KP_DKIN2
+GPIO86 - KP_DKIN3
+GPIO113 - KP_MKIN0
+GPIO114 - KP_MKIN1
+GPIO115 - KP_MKIN2
+GPIO116 - KP_MKIN3
+GPIO117 - KP_MKIN4
+GPIO118 - KP_MKIN5
+GPIO119 - KP_MKIN6
+GPIO120 - KP_MKIN7
+GPIO121 - KP_MKOUT0
+GPIO122 - KP_MKOUT1
+GPIO122 - KP_MKOUT2
+GPIO123 - KP_MKOUT3
+GPIO124 - KP_MKOUT4
+GPIO125 - KP_MKOUT5
+GPIO127 - KP_MKOUT6
+
+Data Bus - Leave unconfigured for now...
+--------
+GPIO2 - nWait (Data Bus)
+
+USB Device
+----------
+GPIO4_2 - USBD_PULLUP
+GPIO10 - UTM_CLK (USB Device UTM Clk)
+GPIO49 - USB 2.0 Device UTM_DATA0
+GPIO50 - USB 2.0 Device UTM_DATA1
+GPIO51 - USB 2.0 Device UTM_DATA2
+GPIO52 - USB 2.0 Device UTM_DATA3
+GPIO53 - USB 2.0 Device UTM_DATA4
+GPIO54 - USB 2.0 Device UTM_DATA5
+GPIO55 - USB 2.0 Device UTM_DATA6
+GPIO56 - USB 2.0 Device UTM_DATA7
+GPIO58 - UTM_RXVALID (USB 2.0 Device)
+GPIO59 - UTM_RXACTIVE (USB 2.0 Device)
+GPIO60 - UTM_RXERROR
+GPIO61 - UTM_OPMODE0
+GPIO62 - UTM_OPMODE1
+GPIO71 - USBD_INT (USB Device?)
+GPIO73 - UTM_TXREADY (USB 2.0 Device)
+GPIO83 - UTM_TXVALID (USB 2.0 Device)
+GPIO98 - UTM_RESET (USB 2.0 device)
+GPIO99 - UTM_XCVR_SELECT
+GPIO100 - UTM_TERM_SELECT
+GPIO101 - UTM_SUSPENDM_X
+GPIO102 - UTM_LINESTATE0
+GPIO103 - UTM_LINESTATE1
+
+Card-Bus Interface - Leave unconfigured for now...
+------------------
+GPIO5 - nPIOR (I/O space output enable)
+GPIO6 - nPIOW (I/O space write enable)
+GPIO7 - nIOS16 (Input from I/O space telling size of data bus)
+GPIO8 - nPWAIT (Input for inserting wait states)
+
+LCD
+---
+GPIO6_2 - LDD0
+GPIO7_2 - LDD1
+GPIO8_2 - LDD2
+GPIO9_2 - LDD3
+GPIO11_2 - LDD5
+GPIO12_2 - LDD6
+GPIO13_2 - LDD7
+GPIO14_2 - VSYNC
+GPIO15_2 - HSYNC
+GPIO16_2 - VCLK
+GPIO17_2 - HCLK
+GPIO18_2 - VDEN
+GPIO63 - LDD8 (CPU LCD)
+GPIO64 - LDD9 (CPU LCD)
+GPIO65 - LDD10 (CPU LCD)
+GPIO66 - LDD11 (CPU LCD)
+GPIO67 - LDD12 (CPU LCD)
+GPIO68 - LDD13 (CPU LCD)
+GPIO69 - LDD14 (CPU LCD)
+GPIO70 - LDD15 (CPU LCD)
+GPIO88 - VCCLCD_PWREN (LCD Panel PWREN)
+GPIO97 - BACKLIGHT_EN
+GPIO104 - LCD_PWREN
+
+PWM - Leave unconfigured for now...
+---
+GPIO11 - PWM0
+GPIO12 - PWM1
+GPIO13 - PWM2
+GPIO14 - PWM3
+
+SD-CARD
+-------
+GPIO18 - SDDATA0
+GPIO19 - SDDATA1
+GPIO20 - SDDATA2
+GPIO21 - SDDATA3
+GPIO22 - SDCLK
+GPIO23 - SDCMD
+GPIO72 - SD_WP
+GPIO84 - SD_nIRQ_CD (SD-Card)
+
+I2C
+---
+GPIO32 - I2CSCL
+GPIO33 - I2CSDA
+
+AC97
+----
+GPIO35 - AC97_SDATA_IN
+GPIO37 - AC97_SDATA_OUT
+GPIO38 - AC97_SYNC
+GPIO39 - AC97_BITCLK
+GPIO40 - AC97_nRESET
+
+UART1
+-----
+GPIO41 - UART_RXD1
+GPIO42 - UART_TXD1
+GPIO43 - UART_CTS1
+GPIO44 - UART_DCD1
+GPIO45 - UART_DSR1
+GPIO46 - UART_nRI1
+GPIO47 - UART_DTR1
+GPIO48 - UART_RTS1
+
+UART2
+-----
+GPIO109 - RTS2
+GPIO110 - RXD2
+GPIO111 - TXD2
+GPIO112 - nCTS2
+
+UART3
+-----
+GPIO105 - nCTS3
+GPIO106 - nRTS3
+GPIO107 - TXD3
+GPIO108 - RXD3
+
+SSP3 - Leave unconfigured for now...
+----
+GPIO89 - SSP3_CLK
+GPIO90 - SSP3_SFRM
+GPIO91 - SSP3_TXD
+GPIO92 - SSP3_RXD
+
+SSP4
+GPIO93 - SSP4_CLK
+GPIO94 - SSP4_SFRM
+GPIO95 - SSP4_TXD
+GPIO96 - SSP4_RXD
+
+Original Definition from Embedian:
+----------------------------------
+#include <mach/mfp-pxa3xx.h>
+
+void xpc8100_mfp_init(void)
+{
+ pxa3xx_mfp_write(MFP_PIN_GPIO0 , 0xa0c0);
+ pxa3xx_mfp_write(MFP_PIN_GPIO1 , 0xa0c0);
+ pxa3xx_mfp_write(MFP_PIN_GPIO2 , 0x20c1);
+ pxa3xx_mfp_write(MFP_PIN_GPIO3 , 0x0801);
+ pxa3xx_mfp_write(MFP_PIN_GPIO4 , 0x0801);
+ pxa3xx_mfp_write(MFP_PIN_GPIO5 , 0x00c3);
+ pxa3xx_mfp_write(MFP_PIN_GPIO6 , 0x00c3);
+ pxa3xx_mfp_write(MFP_PIN_GPIO7 , 0x00c3);
+ pxa3xx_mfp_write(MFP_PIN_GPIO8 , 0x00c3);
+ pxa3xx_mfp_write(MFP_PIN_GPIO9 , 0xa0c0);
+ pxa3xx_mfp_write(MFP_PIN_GPIO10 , 0xa0c0);
+ pxa3xx_mfp_write(MFP_PIN_GPIO11 , 0x00c1);
+ pxa3xx_mfp_write(MFP_PIN_GPIO12 , 0x00c1);
+ pxa3xx_mfp_write(MFP_PIN_GPIO13 , 0x00c1);
+ pxa3xx_mfp_write(MFP_PIN_GPIO14 , 0x00c1);
+ pxa3xx_mfp_write(MFP_PIN_GPIO15 , 0xa0c0);
+ pxa3xx_mfp_write(MFP_PIN_GPIO16 , 0xa0c0);
+ pxa3xx_mfp_write(MFP_PIN_GPIO17 , 0xa0c0);
+ pxa3xx_mfp_write(MFP_PIN_GPIO18 , 0xa0c0);
+ pxa3xx_mfp_write(MFP_PIN_GPIO19 , 0xa0c0);
+ pxa3xx_mfp_write(MFP_PIN_GPIO20 , 0xa0c0);
+ pxa3xx_mfp_write(MFP_PIN_GPIO21 , 0xa0c0);
+ pxa3xx_mfp_write(MFP_PIN_GPIO22 , 0xa0c0);
+ pxa3xx_mfp_write(MFP_PIN_GPIO23 , 0xa0c0);
+ pxa3xx_mfp_write(MFP_PIN_GPIO24 , 0xa0c0);
+ pxa3xx_mfp_write(MFP_PIN_GPIO25 , 0xa0c0);
+ pxa3xx_mfp_write(MFP_PIN_GPIO26 , 0xa0c0);
+ pxa3xx_mfp_write(MFP_PIN_GPIO27 , 0xa0c0);
+ pxa3xx_mfp_write(MFP_PIN_GPIO28 , 0xa0c0);
+ pxa3xx_mfp_write(MFP_PIN_GPIO29 , 0xa0c0);
+ pxa3xx_mfp_write(MFP_PIN_GPIO30 , 0xa0c0);
+ pxa3xx_mfp_write(MFP_PIN_GPIO31 , 0xa0c0);
+ pxa3xx_mfp_write(MFP_PIN_GPIO32 , 0x4981);
+ pxa3xx_mfp_write(MFP_PIN_GPIO33 , 0x4981);
+ pxa3xx_mfp_write(MFP_PIN_GPIO34 , 0xa0c0);
+ pxa3xx_mfp_write(MFP_PIN_GPIO35 , 0x0801);
+ pxa3xx_mfp_write(MFP_PIN_GPIO36 , 0xc0c0);
+ pxa3xx_mfp_write(MFP_PIN_GPIO37 , 0x0801);
+ pxa3xx_mfp_write(MFP_PIN_GPIO38 , 0x0801);
+ pxa3xx_mfp_write(MFP_PIN_GPIO39 , 0x0801);
+ pxa3xx_mfp_write(MFP_PIN_GPIO40 , 0x0801);
+ pxa3xx_mfp_write(MFP_PIN_GPIO41 , 0x08a2);
+ pxa3xx_mfp_write(MFP_PIN_GPIO42 , 0x0882);
+ pxa3xx_mfp_write(MFP_PIN_GPIO43 , 0x0882);
+ pxa3xx_mfp_write(MFP_PIN_GPIO44 , 0x0882);
+ pxa3xx_mfp_write(MFP_PIN_GPIO45 , 0x08a2);
+ pxa3xx_mfp_write(MFP_PIN_GPIO46 , 0x0882);
+ pxa3xx_mfp_write(MFP_PIN_GPIO47 , 0x0882);
+ pxa3xx_mfp_write(MFP_PIN_GPIO48 , 0x0882);
+ pxa3xx_mfp_write(MFP_PIN_GPIO49 , 0xa0c0);
+ pxa3xx_mfp_write(MFP_PIN_GPIO50 , 0xa0c0);
+ pxa3xx_mfp_write(MFP_PIN_GPIO51 , 0xa0c0);
+ pxa3xx_mfp_write(MFP_PIN_GPIO52 , 0xa0c0);
+ pxa3xx_mfp_write(MFP_PIN_GPIO53 , 0xa0c0);
+ pxa3xx_mfp_write(MFP_PIN_GPIO54 , 0xa0c0);
+ pxa3xx_mfp_write(MFP_PIN_GPIO55 , 0xa0c0);
+ pxa3xx_mfp_write(MFP_PIN_GPIO56 , 0xa0c0);
+ pxa3xx_mfp_write(MFP_PIN_GPIO57 , 0xa0c0);
+ pxa3xx_mfp_write(MFP_PIN_GPIO58 , 0xa0c0);
+ pxa3xx_mfp_write(MFP_PIN_GPIO59 , 0xa0c0);
+ pxa3xx_mfp_write(MFP_PIN_GPIO60 , 0xa0c0);
+ pxa3xx_mfp_write(MFP_PIN_GPIO61 , 0xa0c0);
+ pxa3xx_mfp_write(MFP_PIN_GPIO62 , 0xa0c0);
+ pxa3xx_mfp_write(MFP_PIN_GPIO63 , 0x1c01);
+ pxa3xx_mfp_write(MFP_PIN_GPIO64 , 0x1c01);
+ pxa3xx_mfp_write(MFP_PIN_GPIO65 , 0x1c01);
+ pxa3xx_mfp_write(MFP_PIN_GPIO66 , 0x1c01);
+ pxa3xx_mfp_write(MFP_PIN_GPIO67 , 0x1c01);
+ pxa3xx_mfp_write(MFP_PIN_GPIO68 , 0x1c01);
+ pxa3xx_mfp_write(MFP_PIN_GPIO69 , 0x1c01);
+ pxa3xx_mfp_write(MFP_PIN_GPIO70 , 0x1c01);
+ pxa3xx_mfp_write(MFP_PIN_GPIO71 , 0x1c01);
+ pxa3xx_mfp_write(MFP_PIN_GPIO72 , 0x1c01);
+ pxa3xx_mfp_write(MFP_PIN_GPIO73 , 0xa0c0);
+ pxa3xx_mfp_write(MFP_PIN_GPIO74 , 0xa0c0);
+ pxa3xx_mfp_write(MFP_PIN_GPIO75 , 0xa0c0);
+ pxa3xx_mfp_write(MFP_PIN_GPIO76 , 0xa0c0);
+ pxa3xx_mfp_write(MFP_PIN_GPIO77 , 0xa0c0);
+ pxa3xx_mfp_write(MFP_PIN_GPIO78 , 0xa090);
+ pxa3xx_mfp_write(MFP_PIN_GPIO79 , 0xa090);
+ pxa3xx_mfp_write(MFP_PIN_GPIO80 , 0xa090);
+ pxa3xx_mfp_write(MFP_PIN_GPIO81 , 0xa090);
+ pxa3xx_mfp_write(MFP_PIN_GPIO82 , 0xa0c0);
+ pxa3xx_mfp_write(MFP_PIN_GPIO83 , 0xa0c0);
+ pxa3xx_mfp_write(MFP_PIN_GPIO84 , 0xa0c0);
+ pxa3xx_mfp_write(MFP_PIN_GPIO85 , 0xa0c0);
+ pxa3xx_mfp_write(MFP_PIN_GPIO86 , 0xa0c0);
+ pxa3xx_mfp_write(MFP_PIN_GPIO87 , 0xc0c0);
+ pxa3xx_mfp_write(MFP_PIN_GPIO88 , 0xa0c0);
+ pxa3xx_mfp_write(MFP_PIN_GPIO89 , 0xa0c0);
+ pxa3xx_mfp_write(MFP_PIN_GPIO90 , 0xa0c0);
+ pxa3xx_mfp_write(MFP_PIN_GPIO91 , 0xa0c0);
+ pxa3xx_mfp_write(MFP_PIN_GPIO92 , 0xa0c0);
+ pxa3xx_mfp_write(MFP_PIN_GPIO93 , 0xa0c0);
+ pxa3xx_mfp_write(MFP_PIN_GPIO94 , 0xa0c0);
+ pxa3xx_mfp_write(MFP_PIN_GPIO95 , 0xa0c0);
+ pxa3xx_mfp_write(MFP_PIN_GPIO96 , 0xa0c0);
+ pxa3xx_mfp_write(MFP_PIN_GPIO97 , 0xa0c0);
+ pxa3xx_mfp_write(MFP_PIN_GPIO98 , 0xa0c0);
+ pxa3xx_mfp_write(MFP_PIN_GPIO99 , 0xa0c0);
+ pxa3xx_mfp_write(MFP_PIN_GPIO100 , 0xa0c0);
+ pxa3xx_mfp_write(MFP_PIN_GPIO101 , 0xa0c0);
+ pxa3xx_mfp_write(MFP_PIN_GPIO102 , 0xa0c0);
+ pxa3xx_mfp_write(MFP_PIN_GPIO103 , 0xa0c0);
+ pxa3xx_mfp_write(MFP_PIN_GPIO104 , 0xc0c0);
+ pxa3xx_mfp_write(MFP_PIN_GPIO105 , 0x0801);
+ pxa3xx_mfp_write(MFP_PIN_GPIO106 , 0x0801);
+ pxa3xx_mfp_write(MFP_PIN_GPIO107 , 0x0801);
+ pxa3xx_mfp_write(MFP_PIN_GPIO108 , 0x0801);
+ pxa3xx_mfp_write(MFP_PIN_GPIO109 , 0x0801);
+ pxa3xx_mfp_write(MFP_PIN_GPIO110 , 0x0801);
+ pxa3xx_mfp_write(MFP_PIN_GPIO111 , 0x0801);
+ pxa3xx_mfp_write(MFP_PIN_GPIO112 , 0x0801);
+ pxa3xx_mfp_write(MFP_PIN_GPIO113 , 0x08b1);
+ pxa3xx_mfp_write(MFP_PIN_GPIO114 , 0x08b1);
+ pxa3xx_mfp_write(MFP_PIN_GPIO115 , 0x08b1);
+ pxa3xx_mfp_write(MFP_PIN_GPIO116 , 0x08b1);
+ pxa3xx_mfp_write(MFP_PIN_GPIO117 , 0x08b1);
+ pxa3xx_mfp_write(MFP_PIN_GPIO118 , 0x08b1);
+ pxa3xx_mfp_write(MFP_PIN_GPIO119 , 0x08b1);
+ pxa3xx_mfp_write(MFP_PIN_GPIO120 , 0x08b1);
+ pxa3xx_mfp_write(MFP_PIN_GPIO121 , 0x4901);
+ pxa3xx_mfp_write(MFP_PIN_GPIO122 , 0x4901);
+ pxa3xx_mfp_write(MFP_PIN_GPIO123 , 0x4901);
+ pxa3xx_mfp_write(MFP_PIN_GPIO124 , 0x4901);
+ pxa3xx_mfp_write(MFP_PIN_GPIO125 , 0x4901);
+ pxa3xx_mfp_write(MFP_PIN_GPIO126 , 0x4901);
+ pxa3xx_mfp_write(MFP_PIN_GPIO127 , 0x4901);
+ pxa3xx_mfp_write(MFP_PIN_GPIO0_2 , 0xa0c0);
+ pxa3xx_mfp_write(MFP_PIN_GPIO1_2 , 0xa0c0);
+ pxa3xx_mfp_write(MFP_PIN_GPIO2_2 , 0xa0c0);
+ pxa3xx_mfp_write(MFP_PIN_GPIO3_2 , 0xa0c0);
+ pxa3xx_mfp_write(MFP_PIN_GPIO4_2 , 0xc0c0);
+ pxa3xx_mfp_write(MFP_PIN_GPIO5_2 , 0x4901);
+ pxa3xx_mfp_write(MFP_PIN_GPIO6_2 , 0x1c01);
+ pxa3xx_mfp_write(MFP_PIN_GPIO7_2 , 0x1c01);
+ pxa3xx_mfp_write(MFP_PIN_GPIO8_2 , 0x1c01);
+ pxa3xx_mfp_write(MFP_PIN_GPIO9_2 , 0x1c01);
+ pxa3xx_mfp_write(MFP_PIN_GPIO10_2 , 0x1c01);
+ pxa3xx_mfp_write(MFP_PIN_GPIO11_2 , 0x1c01);
+ pxa3xx_mfp_write(MFP_PIN_GPIO12_2 , 0x1c01);
+ pxa3xx_mfp_write(MFP_PIN_GPIO13_2 , 0x1c01);
+ pxa3xx_mfp_write(MFP_PIN_GPIO14_2 , 0x1c01);
+ pxa3xx_mfp_write(MFP_PIN_GPIO15_2 , 0x1c01);
+ pxa3xx_mfp_write(MFP_PIN_GPIO16_2 , 0x1c01);
+ pxa3xx_mfp_write(MFP_PIN_GPIO17_2 , 0x1c01);
+}
+*/
+
+/* MMC/MCI Support */
+#define MAX_MMC_SLOTS 3
+
+#if defined(CONFIG_MMC)
+struct platform_mmc_slot mxm_8x10_mmc_slot[MAX_MMC_SLOTS];
+
+static int mxm_8x10_mci_ro(struct device *dev)
+{
+ struct platform_device *pdev = to_platform_device(dev);
+
+ return gpio_get_value(mxm_8x10_mmc_slot[pdev->id].gpio_wp);
+}
+
+static int mxm_8x10_mci_init(struct device *dev,
+ irq_handler_t mxm_8x10_detect_int, void *data)
+{
+ struct platform_device *pdev = to_platform_device(dev);
+ int err, cd_irq, gpio_cd, gpio_wp;
+
+ cd_irq = gpio_to_irq(mxm_8x10_mmc_slot[pdev->id].gpio_cd);
+ gpio_cd = mxm_8x10_mmc_slot[pdev->id].gpio_cd;
+ gpio_wp = mxm_8x10_mmc_slot[pdev->id].gpio_wp;
+
+ /*
+ * setup GPIO for Zylonite MMC controller
+ */
+ err = gpio_request(gpio_cd, "mmc card detect");
+ if (err)
+ goto err_request_cd;
+ gpio_direction_input(gpio_cd);
+
+ err = gpio_request(gpio_wp, "mmc write protect");
+ if (err)
+ goto err_request_wp;
+ gpio_direction_input(gpio_wp);
+
+ err = request_irq(cd_irq, mxm_8x10_detect_int,
+ IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING,
+ "MMC card detect", data);
+ if (err) {
+ printk(KERN_ERR "%s: MMC/SD/SDIO: "
+ "can't request card detect IRQ\n", __func__);
+ goto err_request_irq;
+ }
+
+ return 0;
+
+err_request_irq:
+ gpio_free(gpio_wp);
+err_request_wp:
+ gpio_free(gpio_cd);
+err_request_cd:
+ return err;
+}
+
+static void mxm_8x10_mci_exit(struct device *dev, void *data)
+{
+ struct platform_device *pdev = to_platform_device(dev);
+ int cd_irq, gpio_cd, gpio_wp;
+
+ cd_irq = gpio_to_irq(xpc8100_mmc_slot[pdev->id].gpio_cd);
+ gpio_cd = mxm_8x10_mmc_slot[pdev->id].gpio_cd;
+ gpio_wp = mxm_8x10_mmc_slot[pdev->id].gpio_wp;
+
+ free_irq(cd_irq, data);
+ gpio_free(gpio_cd);
+ gpio_free(gpio_wp);
+}
+
+static struct pxamci_platform_data mxm_8x10_mci_platform_data = {
+ .detect_delay = 20,
+ .ocr_mask = MMC_VDD_32_33 | MMC_VDD_33_34,
+ .init = mxm_8x10_mci_init,
+ .exit = mxm_8x10_mci_exit,
+ .get_ro = mxm_8x10_mci_ro,
+};
+
+static struct pxamci_platform_data mxm_8x10_mci2_platform_data = {
+ .detect_delay = 20,
+ .ocr_mask = MMC_VDD_32_33 | MMC_VDD_33_34,
+};
+
+void __init mxm_8x10_mmc_init(void)
+{
+ /* Seems a bit insane - GPIO1 and GPIO5 has nothing to do with MMC
+ * according to the docs, but they are used here as Card Detect and
+ * Write Protect. What is going on on pins 72 and 83?
+ * Note: Embedian docs say that SD-Card does not work under linux.
+ */
+ pxa3xx_mfp_write(MFP_PIN_GPIO1, 0xa0c0); /* Card Detect */
+ pxa3xx_mfp_write(MFP_PIN_GPIO5, 0x00c3); /* Write Protect */
+ pxa3xx_mfp_write(MFP_PIN_GPIO18, 0xa0c0); /* SD_DATA0 */
+ pxa3xx_mfp_write(MFP_PIN_GPIO19, 0xa0c0); /* SD_DATA1 */
+ pxa3xx_mfp_write(MFP_PIN_GPIO20, 0xa0c0); /* SD_DATA2 */
+ pxa3xx_mfp_write(MFP_PIN_GPIO21, 0xa0c0); /* SD_DATA3 */
+ pxa3xx_mfp_write(MFP_PIN_GPIO22, 0xa0c0); /* SD_CLK */
+ pxa3xx_mfp_write(MFP_PIN_GPIO23, 0xa0c0); /* SD_CMD */
+ pxa3xx_mfp_write(MFP_PIN_GPIO72, 0x1c01); /* SD_WP */
+ pxa3xx_mfp_write(MFP_PIN_GPIO83, 0xa0c0); /* SD_CD_nIRQ */
+
+ /* MMC card detect & write protect for controller 0 */
+ mxm_8x10_mmc_slot[0].gpio_cd = mfp_to_gpio(MFP_PIN_GPIO1);
+ mxm_8x10_mmc_slot[0].gpio_wp = mfp_to_gpio(MFP_PIN_GPIO5);
+
+ pxa_set_mci_info(&mxm_8x10_mci_platform_data);
+ pxa3xx_set_mci2_info(&mxm_8x10_mci2_platform_data);
+ if (cpu_is_pxa310())
+ pxa3xx_set_mci3_info(&mxm_8x10_mci_platform_data);
+}
+#else
+inline void mxm_8x10_mmc_init(void)
+{
+}
+#endif
+
+/* USB Open Host Controler Interface */
+static struct pxaohci_platform_data mxm_8x10_ohci_platform_data = {
+ .port_mode = PMM_NPS_MODE,
+ .flags = ENABLE_PORT_ALL,
+};
+
+void __init mxm_8x10_usb_host_init(void)
+{
+ pxa3xx_mfp_write(MFP_PIN_GPIO10, 0xa0c0); /* UTM_CLK */
+ pxa3xx_mfp_write(MFP_PIN_GPIO49, 0xa0c0); /* UTM_DATA0 */
+ pxa3xx_mfp_write(MFP_PIN_GPIO50, 0xa0c0); /* UTM_DATA1 */
+ pxa3xx_mfp_write(MFP_PIN_GPIO51, 0xa0c0); /* UTM_DATA2 */
+ pxa3xx_mfp_write(MFP_PIN_GPIO52, 0xa0c0); /* UTM_DATA3 */
+ pxa3xx_mfp_write(MFP_PIN_GPIO53, 0xa0c0); /* UTM_DATA4 */
+ pxa3xx_mfp_write(MFP_PIN_GPIO54, 0xa0c0); /* UTM_DATA5 */
+ pxa3xx_mfp_write(MFP_PIN_GPIO55, 0xa0c0); /* UTM_DATA6 */
+ pxa3xx_mfp_write(MFP_PIN_GPIO56, 0xa0c0); /* UTM_DATA7 */
+ pxa3xx_mfp_write(MFP_PIN_GPIO58, 0xa0c0); /* UTM_RXVALID */
+ pxa3xx_mfp_write(MFP_PIN_GPIO59, 0xa0c0); /* UTM_RXACTIVE */
+ pxa3xx_mfp_write(MFP_PIN_GPIO60, 0xa0c0); /* UTM_RXERROR */
+ pxa3xx_mfp_write(MFP_PIN_GPIO61, 0xa0c0); /* UTM_OPMODE0 */
+ pxa3xx_mfp_write(MFP_PIN_GPIO62, 0xa0c0); /* UTM_OPMODE1 */
+ pxa3xx_mfp_write(MFP_PIN_GPIO71, 0x1c01); /* USBD_INT */
+ pxa3xx_mfp_write(MFP_PIN_GPIO73, 0xa0c0); /* UTM_TXREADY */
+ pxa3xx_mfp_write(MFP_PIN_GPIO83, 0xa0c0); /* UTM_TXVALID */
+ pxa3xx_mfp_write(MFP_PIN_GPIO98, 0xa0c0); /* UTM_RESET */
+ pxa3xx_mfp_write(MFP_PIN_GPIO99, 0xa0c0); /* UTM_XCVR_SELECT */
+ pxa3xx_mfp_write(MFP_PIN_GPIO100, 0xa0c0); /* UTM_TERM_SELECT */
+ pxa3xx_mfp_write(MFP_PIN_GPIO101, 0xa0c0); /* UTM_SUSPENDM_X */
+ pxa3xx_mfp_write(MFP_PIN_GPIO102, 0xa0c0); /* UTM_LINESTATE0 */
+ pxa3xx_mfp_write(MFP_PIN_GPIO103, 0xa0c0); /* UTM_LINESTATE1 */
+ pxa3xx_mfp_write(MFP_PIN_GPIO4_2, 0xc0c0); /* UTM_PULLUP */
+
+ pxa_set_ohci_info(&mxm_8x10_ohci_platform_data);
+}
+
+/* AC97 Sound Support */
+static struct platform_device mxm_8x10_ac97_device = {
+ .name = "pxa2xx-ac97",
+};
+
+void __init mxm_8x10_ac97_init(void)
+{
+ pxa3xx_mfp_write(MFP_PIN_GPIO35, 0x0801); /* AC97_SDATA_IN */
+ pxa3xx_mfp_write(MFP_PIN_GPIO37, 0x0801); /* AC97_SDATA_OUT */
+ pxa3xx_mfp_write(MFP_PIN_GPIO38, 0x0801); /* AC97_SYNC */
+ pxa3xx_mfp_write(MFP_PIN_GPIO39, 0x0801); /* AC97_BITCLK */
+ pxa3xx_mfp_write(MFP_PIN_GPIO40, 0x0801); /* AC97_nRESET */
+
+ platform_device_register(&mxm_8x10_ac97_device);
+}
+
+/* NAND flash Support */
+#if defined(CONFIG_MTD_NAND_PXA3xx) || defined(CONFIG_MTD_NAND_PXA3xx_MODULE)
+#define NAND_BLOCK_SIZE SZ_128K
+#define NB(x) (NAND_BLOCK_SIZE * (x))
+struct mtd_partition mxm_8x10_nand_partitions[] = {
+ [0] = {
+ .name = "boot",
+ .size = NB(0x002),
+ .offset = NB(0x000),
+ .mask_flags = MTD_WRITEABLE,
+ },
+ [1] = {
+ .name = "kernel",
+ .size = NB(0x010),
+ .offset = NB(0x002),
+ .mask_flags = MTD_WRITEABLE,
+ },
+ [2] = {
+ .name = "root",
+ .size = NB(0x36c),
+ .offset = NB(0x012),
+ },
+ [3] = {
+ .name = "bbt",
+ .size = NB(0x082),
+ .offset = NB(0x37e),
+ .mask_flags = MTD_WRITEABLE,
+ },
+};
+
+static struct pxa3xx_nand_platform_data mxm_8x10_nand_info = {
+ .enable_arbiter = 1,
+ .keep_config = 1,
+ .parts = mxm_8x10_nand_partitions,
+ .nr_parts = ARRAY_SIZE(mxm_8x10_nand_partitions),
+};
+
+void __init mxm_8x10_nand_init(void)
+{
+ pxa3xx_set_nand_info(&mxm_8x10_nand_info);
+}
+#else
+inline mxm_8x10_nand_init(void)
+{
+}
+#endif /* CONFIG_MTD_NAND_PXA3xx || CONFIG_MTD_NAND_PXA3xx_MODULE */
+
+/* Ethernet support: Davicom DM9000 */
+int gpio_eth_irq;
+
+static struct resource dm9k_resources[] = {
+ [0] = {
+ .start = MXM_8X10_ETH_PHYS + 0x300,
+ .end = MXM_8X10_ETH_PHYS + 0x300,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = MXM_8X10_ETH_PHYS + 0x308,
+ .end = MXM_8X10_ETH_PHYS + 0x308,
+ .flags = IORESOURCE_MEM,
+ },
+ [2] = {
+ .start = -1, /* for run-time assignment */
+ .end = -1,
+ .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHEDGE,
+ }
+};
+
+static struct dm9000_plat_data dm9k_plat_data = {
+ .flags = DM9000_PLATF_16BITONLY,
+};
+
+static struct platform_device dm9k_device = {
+ .name = "dm9000",
+ .id = 0,
+ .num_resources = ARRAY_SIZE(dm9k_resources),
+ .resource = dm9k_resources,
+ .dev = {
+ .platform_data = &dm9k_plat_data,
+ }
+};
+
+void __init mxm_8x10_ethernet_init(void)
+{
+ pxa3xx_mfp_write(MFP_PIN_GPIO1, 0xa0c0); /* DM9000_PWR ? */
+ pxa3xx_mfp_write(MFP_PIN_GPIO9, 0xa0c0); /* DM9000_nIRQ */
+ pxa3xx_mfp_write(MFP_PIN_GPIO36, 0xc0c0); /* DM9000_RESET */
+
+ gpio_eth_irq = mfp_to_gpio(MFP_PIN_GPIO9);
+
+ dm9k_resources[2].start = gpio_to_irq(gpio_eth_irq);
+ dm9k_resources[2].end = gpio_to_irq(gpio_eth_irq);
+ platform_device_register(&dm9k_device);
+}
+
+/* PXA UARTs */
+static void __init mxm_8x10_uarts_init(void)
+{
+ pxa3xx_mfp_write(MFP_PIN_GPIO41, 0x08a2); /* UART_RXD1 */
+ pxa3xx_mfp_write(MFP_PIN_GPIO42, 0x0882); /* UART_TXD1 */
+ pxa3xx_mfp_write(MFP_PIN_GPIO43, 0x0882); /* UART_CTS1 */
+ pxa3xx_mfp_write(MFP_PIN_GPIO44, 0x0882); /* UART_DCD1 */
+ pxa3xx_mfp_write(MFP_PIN_GPIO45, 0x08a2); /* UART_DSR1 */
+ pxa3xx_mfp_write(MFP_PIN_GPIO46, 0x0882); /* UART_nRI1 */
+ pxa3xx_mfp_write(MFP_PIN_GPIO47, 0x0882); /* UART_DTR1 */
+ pxa3xx_mfp_write(MFP_PIN_GPIO48, 0x0882); /* UART_RTS1 */
+
+ pxa3xx_mfp_write(MFP_PIN_GPIO109, 0x0801); /* UART_RTS2 */
+ pxa3xx_mfp_write(MFP_PIN_GPIO110, 0x0801); /* UART_RXD2 */
+ pxa3xx_mfp_write(MFP_PIN_GPIO111, 0x0801); /* UART_TXD2 */
+ pxa3xx_mfp_write(MFP_PIN_GPIO112, 0x0801); /* UART_nCTS2 */
+
+ pxa3xx_mfp_write(MFP_PIN_GPIO105, 0x0801); /* UART_nCTS3 */
+ pxa3xx_mfp_write(MFP_PIN_GPIO106, 0x0801); /* UART_nRTS3 */
+ pxa3xx_mfp_write(MFP_PIN_GPIO107, 0x0801); /* UART_TXD3 */
+ pxa3xx_mfp_write(MFP_PIN_GPIO108, 0x0801); /* UART_RXD3 */
+
+ pxa_set_ffuart_info(NULL);
+ pxa_set_btuart_info(NULL);
+ pxa_set_stuart_info(NULL);
+}
+
+/* Backlight, LCD and Frame-Buffer */
+#if defined(CONFIG_FB_PXA) || defined(CONFIG_FB_PXA_MODULE)
+int gpio_backlight;
+
+int lcd_id;
+int lcd_orientation;
+
+#define NUM_LCD_DETECT_PINS 7
+
+static int lcd_detect_pins[] __initdata = {
+ MFP_PIN_GPIO72, /* LCD_LDD_17 - ORIENT */
+ MFP_PIN_GPIO71, /* LCD_LDD_16 - LCDID[5] */
+ MFP_PIN_GPIO17_2, /* LCD_BIAS - LCDID[4] */
+ MFP_PIN_GPIO15_2, /* LCD_LCLK - LCDID[3] */
+ MFP_PIN_GPIO14_2, /* LCD_FCLK - LCDID[2] */
+ MFP_PIN_GPIO73, /* LCD_CS_N - LCDID[1] */
+ MFP_PIN_GPIO74, /* LCD_VSYNC - LCDID[0] */
+ /*
+ * set the MFP_PIN_GPIO 14/15/17 to alternate function other than
+ * GPIO to avoid input level confliction with 14_2, 15_2, 17_2
+ */
+ MFP_PIN_GPIO14,
+ MFP_PIN_GPIO15,
+ MFP_PIN_GPIO17,
+};
+
+static int lcd_detect_mfpr[] __initdata = {
+ /* AF0, DS 1X, Pull Neither, Edge Clear */
+ 0x8440, 0x8440, 0x8440, 0x8440, 0x8440, 0x8440, 0x8440,
+ 0xc442, /* Backlight, Pull-Up, AF2 */
+ 0x8445, /* AF5 */
+ 0x8445, /* AF5 */
+};
+
+static void __init mxm_8x10_detect_lcd_panel(void)
+{
+ unsigned long mfpr_save[ARRAY_SIZE(lcd_detect_pins)];
+ int i, gpio, id = 0;
+
+ /* save the original MFP settings of these pins and configure them
+ * as GPIO Input, DS01X, Pull Neither, Edge Clear
+ */
+ for (i = 0; i < ARRAY_SIZE(lcd_detect_pins); i++) {
+ mfpr_save[i] = pxa3xx_mfp_read(lcd_detect_pins[i]);
+ pxa3xx_mfp_write(lcd_detect_pins[i], lcd_detect_mfpr[i]);
+ }
+
+ for (i = 0; i < NUM_LCD_DETECT_PINS; i++) {
+ id = id << 1;
+ gpio = mfp_to_gpio(lcd_detect_pins[i]);
+ gpio_request(gpio, "LCD_ID_PINS");
+ gpio_direction_input(gpio);
+
+ if (gpio_get_value(gpio))
+ id = id | 0x1;
+ gpio_free(gpio);
+ }
+
+ /* lcd id, flush out bit 1 */
+ lcd_id = id & 0x3d;
+
+ /* lcd orientation, portrait or landscape */
+ lcd_orientation = (id >> 6) & 0x1;
+
+ printk(KERN_INFO "%s: lcd_id = %d, orientation = %d \n", __func__,
+ lcd_id, lcd_orientation);
+
+ /* restore the original MFP settings */
+ for (i = 0; i < ARRAY_SIZE(lcd_detect_pins); i++)
+ pxa3xx_mfp_write(lcd_detect_pins[i], mfpr_save[i]);
+}
+
+static void mxm_8x10_backlight_power(int on)
+{
+ gpio_set_value(gpio_backlight, on);
+}
+
+static struct pxafb_mode_info toshiba_ltm04c380k_mode = {
+ .pixclock = 30000,
+ .xres = 640,
+ .yres = 480,
+ .bpp = 16,
+ .hsync_len = 40,
+ .left_margin = 128,
+ .right_margin = 24,
+ .vsync_len = 3,
+ .upper_margin = 28,
+ .lower_margin = 9,
+ .sync = FB_SYNC_HOR_HIGH_ACT | FB_SYNC_VERT_HIGH_ACT,
+};
+
+static struct pxafb_mach_info mxm_8x10_toshiba_lcd_info = {
+ .num_modes = 1,
+ .lccr0 = LCCR0_Act,
+ .lccr3 = LCCR3_PCP,
+ .pxafb_backlight_power = mxm_8x10_backlight_power,
+};
+
+void __init mxm_8x10_lcd_init(void)
+{
+ pxa3xx_mfp_write(MFP_PIN_GPIO6_2, 0x1c01); /* LDD0 */
+ pxa3xx_mfp_write(MFP_PIN_GPIO7_2, 0x1c01); /* LDD1 */
+ pxa3xx_mfp_write(MFP_PIN_GPIO8_2, 0x1c01); /* LDD2 */
+ pxa3xx_mfp_write(MFP_PIN_GPIO9_2, 0x1c01); /* LDD3 */
+ pxa3xx_mfp_write(MFP_PIN_GPIO10_2, 0x1c01); /* LDD4 */
+ pxa3xx_mfp_write(MFP_PIN_GPIO11_2, 0x1c01); /* LDD5 */
+ pxa3xx_mfp_write(MFP_PIN_GPIO12_2, 0x1c01); /* LDD6 */
+ pxa3xx_mfp_write(MFP_PIN_GPIO13_2, 0x1c01); /* LDD7 */
+ pxa3xx_mfp_write(MFP_PIN_GPIO63, 0x1c01); /* LDD8 */
+ pxa3xx_mfp_write(MFP_PIN_GPIO64, 0x1c01); /* LDD9 */
+ pxa3xx_mfp_write(MFP_PIN_GPIO65, 0x1c01); /* LDD10 */
+ pxa3xx_mfp_write(MFP_PIN_GPIO66, 0x1c01); /* LDD11 */
+ pxa3xx_mfp_write(MFP_PIN_GPIO67, 0x1c01); /* LDD12 */
+ pxa3xx_mfp_write(MFP_PIN_GPIO68, 0x1c01); /* LDD13 */
+ pxa3xx_mfp_write(MFP_PIN_GPIO69, 0x1c01); /* LDD14 */
+ pxa3xx_mfp_write(MFP_PIN_GPIO70, 0x1c01); /* LDD15 */
+ pxa3xx_mfp_write(MFP_PIN_GPIO14_2, 0x1c01); /* VSYNC */
+ pxa3xx_mfp_write(MFP_PIN_GPIO15_2, 0x1c01); /* HSYNC */
+ pxa3xx_mfp_write(MFP_PIN_GPIO16_2, 0x1c01); /* VCLK */
+ pxa3xx_mfp_write(MFP_PIN_GPIO17_2, 0x1c01); /* HCLK */
+ pxa3xx_mfp_write(MFP_PIN_GPIO88, 0xa0c0); /* VCCLCD_PWREN */
+ pxa3xx_mfp_write(MFP_PIN_GPIO104, 0xc0c0); /* LCD_PWREN */
+ pxa3xx_mfp_write(MFP_PIN_GPIO97, 0xa0c0); /* BACKLIGHT_EN */
+
+ gpio_backlight = mfp_to_gpio(MFP_PIN_GPIO14);
+
+ mxm_8x10_detect_lcd_panel();
+
+ /* backlight GPIO: output, default on */
+ gpio_direction_output(gpio_backlight, 1);
+
+ mxm_8x10_toshiba_lcd_info.modes = &toshiba_ltm04c380k_mode;
+ set_pxa_fb_info(&mxm_8x10_toshiba_lcd_info);
+}
+#else
+inline void mxm_8x10_lcd_init(void)
+{
+}
+#endif
+
+/* I2C and Real Time Clock */
+static struct i2c_board_info __initdata mxm_8x10_i2c_devices[] = {
+ {
+ I2C_BOARD_INFO("ds1337", 0x68),
+ },
+};
+
+void __init mxm_8x10_i2c_init(void)
+{
+ pxa3xx_mfp_write(MFP_PIN_GPIO32, 0x4981); /* I2CSCL */
+ pxa3xx_mfp_write(MFP_PIN_GPIO33, 0x4981); /* I2CSDA */
+
+ i2c_register_board_info(0, mxm_8x10_i2c_devices,
+ ARRAY_SIZE(mxm_8x10_i2c_devices));
+ pxa_set_i2c_info(NULL);
+}
+
+void __init mxm_8x10_barebones_init(void)
+{
+ mxm_8x10_uarts_init();
+ mxm_8x10_nand_init();
+ mxm_8x10_i2c_init();
+ mxm_8x10_ethernet_init();
+}
More information about the linux-arm-kernel
mailing list