[PATCH 16/18] ARM: PNX4008: i2c-pnx: don't split messages across several lines
Russell King - ARM Linux
linux at arm.linux.org.uk
Sat Jan 2 06:21:50 EST 2010
It makes them harder to grep for.
Signed-off-by: Russell King <rmk+kernel at arm.linux.org.uk>
---
drivers/i2c/busses/i2c-pnx.c | 81 +++++++++++++++++++++++-------------------
1 files changed, 44 insertions(+), 37 deletions(-)
diff --git a/drivers/i2c/busses/i2c-pnx.c b/drivers/i2c/busses/i2c-pnx.c
index da11ade..a71cd93 100644
--- a/drivers/i2c/busses/i2c-pnx.c
+++ b/drivers/i2c/busses/i2c-pnx.c
@@ -86,25 +86,26 @@ static int i2c_pnx_start(unsigned char slave_addr,
/* Check for 7 bit slave addresses only */
if (slave_addr & ~0x7f) {
- dev_err(&alg_data->adapter.dev, "%s: Invalid slave address %x. "
- "Only 7-bit addresses are supported\n",
- alg_data->adapter.name, slave_addr);
+ dev_err(&alg_data->adapter.dev,
+ "%s: Invalid slave address %x. Only 7-bit addresses are supported\n",
+ alg_data->adapter.name, slave_addr);
return -EINVAL;
}
/* First, make sure bus is idle */
if (wait_timeout(I2C_PNX_TIMEOUT, alg_data)) {
/* Somebody else is monopolizing the bus */
- dev_err(&alg_data->adapter.dev, "%s: Bus busy. Slave addr = %02x, "
- "cntrl = %x, stat = %x\n",
- alg_data->adapter.name, slave_addr,
- ioread32(I2C_REG_CTL(alg_data)),
- ioread32(I2C_REG_STS(alg_data)));
+ dev_err(&alg_data->adapter.dev,
+ "%s: Bus busy. Slave addr = %02x, cntrl = %x, stat = %x\n",
+ alg_data->adapter.name, slave_addr,
+ ioread32(I2C_REG_CTL(alg_data)),
+ ioread32(I2C_REG_STS(alg_data)));
return -EBUSY;
} else if (ioread32(I2C_REG_STS(alg_data)) & mstatus_afi) {
/* Sorry, we lost the bus */
- dev_err(&alg_data->adapter.dev, "%s: Arbitration failure. "
- "Slave addr = %02x\n", alg_data->adapter.name, slave_addr);
+ dev_err(&alg_data->adapter.dev,
+ "%s: Arbitration failure. Slave addr = %02x\n",
+ alg_data->adapter.name, slave_addr);
return -EIO;
}
@@ -182,15 +183,15 @@ static int i2c_pnx_master_xmit(struct i2c_pnx_algo_data *alg_data)
alg_data->mif.len--;
iowrite32(val, I2C_REG_TX(alg_data));
- dev_dbg(&alg_data->adapter.dev, "%s(): xmit %#x [%d]\n", __func__,
- val, alg_data->mif.len + 1);
+ dev_dbg(&alg_data->adapter.dev, "%s(): xmit %#x [%d]\n",
+ __func__, val, alg_data->mif.len + 1);
if (alg_data->mif.len == 0) {
if (alg_data->last) {
/* Wait until the STOP is seen. */
if (wait_timeout(I2C_PNX_TIMEOUT, alg_data))
- dev_err(&alg_data->adapter.dev, "The bus is still "
- "active after timeout\n");
+ dev_err(&alg_data->adapter.dev,
+ "The bus is still active after timeout\n");
}
/* Disable master interrupts */
iowrite32(ioread32(I2C_REG_CTL(alg_data)) &
@@ -199,7 +200,8 @@ static int i2c_pnx_master_xmit(struct i2c_pnx_algo_data *alg_data)
del_timer_sync(&alg_data->mif.timer);
- dev_dbg(&alg_data->adapter.dev, "%s(): Waking up xfer routine.\n",
+ dev_dbg(&alg_data->adapter.dev,
+ "%s(): Waking up xfer routine.\n",
__func__);
complete(&alg_data->mif.complete);
@@ -215,8 +217,9 @@ static int i2c_pnx_master_xmit(struct i2c_pnx_algo_data *alg_data)
/* Stop timer. */
del_timer_sync(&alg_data->mif.timer);
- dev_dbg(&alg_data->adapter.dev, "%s(): Waking up xfer routine after "
- "zero-xfer.\n", __func__);
+ dev_dbg(&alg_data->adapter.dev,
+ "%s(): Waking up xfer routine after zero-xfer.\n",
+ __func__);
complete(&alg_data->mif.complete);
}
@@ -245,8 +248,9 @@ static int i2c_pnx_master_rcv(struct i2c_pnx_algo_data *alg_data)
* or we didn't 'ask' for it yet.
*/
if (ioread32(I2C_REG_STS(alg_data)) & mstatus_rfe) {
- dev_dbg(&alg_data->adapter.dev, "%s(): Write dummy data to fill "
- "Rx-fifo...\n", __func__);
+ dev_dbg(&alg_data->adapter.dev,
+ "%s(): Write dummy data to fill Rx-fifo...\n",
+ __func__);
if (alg_data->mif.len == 1) {
/* Last byte, do not acknowledge next rcv. */
@@ -278,16 +282,16 @@ static int i2c_pnx_master_rcv(struct i2c_pnx_algo_data *alg_data)
if (alg_data->mif.len > 0) {
val = ioread32(I2C_REG_RX(alg_data));
*alg_data->mif.buf++ = (u8) (val & 0xff);
- dev_dbg(&alg_data->adapter.dev, "%s(): rcv 0x%x [%d]\n", __func__, val,
- alg_data->mif.len);
+ dev_dbg(&alg_data->adapter.dev, "%s(): rcv 0x%x [%d]\n",
+ __func__, val, alg_data->mif.len);
alg_data->mif.len--;
if (alg_data->mif.len == 0) {
if (alg_data->last)
/* Wait until the STOP is seen. */
if (wait_timeout(I2C_PNX_TIMEOUT, alg_data))
- dev_err(&alg_data->adapter.dev, "The bus is still "
- "active after timeout\n");
+ dev_err(&alg_data->adapter.dev,
+ "The bus is still active after timeout\n");
/* Disable master interrupts */
ctl = ioread32(I2C_REG_CTL(alg_data));
@@ -312,7 +316,8 @@ static irqreturn_t i2c_pnx_interrupt(int irq, void *dev_id)
struct i2c_pnx_algo_data *alg_data = dev_id;
u32 stat, ctl;
- dev_dbg(&alg_data->adapter.dev, "%s(): mstat = %x mctrl = %x, mode = %d\n",
+ dev_dbg(&alg_data->adapter.dev,
+ "%s(): mstat = %x mctrl = %x, mode = %d\n",
__func__,
ioread32(I2C_REG_STS(alg_data)),
ioread32(I2C_REG_CTL(alg_data)),
@@ -335,8 +340,8 @@ static irqreturn_t i2c_pnx_interrupt(int irq, void *dev_id)
complete(&alg_data->mif.complete);
} else if (stat & mstatus_nai) {
/* Slave did not acknowledge, generate a STOP */
- dev_dbg(&alg_data->adapter.dev, "%s(): "
- "Slave did not acknowledge, generating a STOP.\n",
+ dev_dbg(&alg_data->adapter.dev,
+ "%s(): Slave did not acknowledge, generating a STOP.\n",
__func__);
i2c_pnx_stop(alg_data);
@@ -375,7 +380,8 @@ static irqreturn_t i2c_pnx_interrupt(int irq, void *dev_id)
stat = ioread32(I2C_REG_STS(alg_data));
iowrite32(stat | mstatus_tdi | mstatus_afi, I2C_REG_STS(alg_data));
- dev_dbg(&alg_data->adapter.dev, "%s(): exiting, stat = %x ctrl = %x.\n",
+ dev_dbg(&alg_data->adapter.dev,
+ "%s(): exiting, stat = %x ctrl = %x.\n",
__func__, ioread32(I2C_REG_STS(alg_data)),
ioread32(I2C_REG_CTL(alg_data)));
@@ -387,10 +393,10 @@ static void i2c_pnx_timeout(unsigned long data)
struct i2c_pnx_algo_data *alg_data = (struct i2c_pnx_algo_data *)data;
u32 ctl;
- dev_err(&alg_data->adapter.dev, "Master timed out. stat = %04x, cntrl = %04x. "
- "Resetting master...\n",
- ioread32(I2C_REG_STS(alg_data)),
- ioread32(I2C_REG_CTL(alg_data)));
+ dev_err(&alg_data->adapter.dev,
+ "Master timed out. stat = %04x, cntrl = %04x. Resetting master...\n",
+ ioread32(I2C_REG_STS(alg_data)),
+ ioread32(I2C_REG_CTL(alg_data)));
/* Reset master and disable interrupts */
ctl = ioread32(I2C_REG_CTL(alg_data));
@@ -411,7 +417,7 @@ static inline void bus_reset_if_active(struct i2c_pnx_algo_data *alg_data)
if ((stat = ioread32(I2C_REG_STS(alg_data))) & mstatus_active) {
dev_err(&alg_data->adapter.dev,
"%s: Bus is still active after xfer. Reset it...\n",
- alg_data->adapter.name);
+ alg_data->adapter.name);
iowrite32(ioread32(I2C_REG_CTL(alg_data)) | mcntrl_reset,
I2C_REG_CTL(alg_data));
wait_reset(I2C_PNX_TIMEOUT, alg_data);
@@ -445,7 +451,8 @@ i2c_pnx_xfer(struct i2c_adapter *adap, struct i2c_msg *msgs, int num)
struct i2c_pnx_algo_data *alg_data = adap->algo_data;
u32 stat = ioread32(I2C_REG_STS(alg_data));
- dev_dbg(&alg_data->adapter.dev, "%s(): entering: %d messages, stat = %04x.\n",
+ dev_dbg(&alg_data->adapter.dev,
+ "%s(): entering: %d messages, stat = %04x.\n",
__func__, num, ioread32(I2C_REG_STS(alg_data)));
bus_reset_if_active(alg_data);
@@ -472,9 +479,8 @@ i2c_pnx_xfer(struct i2c_adapter *adap, struct i2c_msg *msgs, int num)
alg_data->mif.ret = 0;
alg_data->last = (i == num - 1);
- dev_dbg(&alg_data->adapter.dev, "%s(): mode %d, %d bytes\n", __func__,
- alg_data->mif.mode,
- alg_data->mif.len);
+ dev_dbg(&alg_data->adapter.dev, "%s(): mode %d, %d bytes\n",
+ __func__, alg_data->mif.mode, alg_data->mif.len);
i2c_pnx_arm_timer(alg_data);
@@ -496,7 +502,8 @@ i2c_pnx_xfer(struct i2c_adapter *adap, struct i2c_msg *msgs, int num)
if (!(rc = alg_data->mif.ret))
completed++;
- dev_dbg(&alg_data->adapter.dev, "%s(): Complete, return code = %d.\n",
+ dev_dbg(&alg_data->adapter.dev,
+ "%s(): Complete, return code = %d.\n",
__func__, rc);
/* Clear TDI and AFI bits in case they are set. */
--
1.6.2.5
More information about the linux-arm-kernel
mailing list