[PATCH 6/6] omap2+: Initialize serial ports for wake-up events for n8x0

[Kevin Hilman]

Tony Lindgren <tony at atomide.com> writes:

> Use omap_serial_init_port so we can let the serial code handle the
> remuxing of the RX pads.
>
> Signed-off-by: Tony Lindgren <tony at atomide.com>

Does this work for UART wakeups on n810?  I don't see any 'idle' value
for the pads, so I'm guessing it wont work without those, right?  Or am
I missing something here.

Kevin

> ---
>  arch/arm/mach-omap2/board-n8x0.c |   66 ++++++++++++++++++++++++++++++++++++--
>  1 files changed, 63 insertions(+), 3 deletions(-)
>
> diff --git a/arch/arm/mach-omap2/board-n8x0.c b/arch/arm/mach-omap2/board-n8x0.c
> index d022301..e3429b4 100644
> --- a/arch/arm/mach-omap2/board-n8x0.c
> +++ b/arch/arm/mach-omap2/board-n8x0.c
> @@ -29,6 +29,7 @@
>  
>  #include <plat/board.h>
>  #include <plat/common.h>
> +#include <plat/omap_device.h>
>  #include <plat/menelaus.h>
>  #include <mach/irqs.h>
>  #include <plat/mcspi.h>
> @@ -754,8 +755,68 @@ static struct omap_board_mux board_mux[] __initdata = {
>  	OMAP2420_MUX(EAC_AC_DOUT, OMAP_MUX_MODE1 | OMAP_PIN_OUTPUT),
>  	{ .reg_offset = OMAP_MUX_TERMINATOR },
>  };
> +
> +static struct omap_device_pad serial0_pads[] __initdata = {
> +	{ .name	= "uart1_rx.uart1_rx", .enable	= OMAP_MUX_MODE0 },
> +	{ .name	= "uart1_tx.uart1_tx", .enable	= OMAP_MUX_MODE0 },
> +};
> +
> +static struct omap_device_pad n800_serial1_pads[] __initdata = {
> +	{ .name	= "uart2_rx.uart2_rx", .enable	= OMAP_MUX_MODE7, },
> +	{
> +		.name	= "uart2_tx.uart2_tx",
> +		.enable	= OMAP_PULL_ENA | OMAP_MUX_MODE7,
> +	},
> +};
> +
> +static struct omap_device_pad n810_serial1_pads[] __initdata = {
> +	{ .name	= "uart2_rx.uart2_rx", .enable	= OMAP_MUX_MODE0, },
> +	{ .name	= "uart2_tx.uart2_tx", .enable	= OMAP_MUX_MODE0, },
> +};
> +
> +static struct omap_device_pad serial2_pads[] __initdata = {
> +	{
> +		.name	= "uart3_rx_irrx.uart3_rx_irrx",
> +		.flags	= OMAP_DEVICE_PAD_REMUX | OMAP_DEVICE_PAD_WAKEUP,
> +		.enable	= OMAP_MUX_MODE0,
> +		.idle	= OMAP_MUX_MODE3	/* Mux as GPIO for idle */
> +	},
> +	{ .name	= "uart3_tx_irtx.uart3_tx_irtx", .enable = OMAP_MUX_MODE0, },
> +};
> +
> +static struct omap_device_board_data serial0_data = {
> +	.id		= 0,
> +	.pads		= serial0_pads,
> +	.pads_cnt	= ARRAY_SIZE(serial0_pads),
> +};
> +
> +static struct omap_device_board_data serial1_data = {
> +	.id		= 1,
> +};
> +
> +static struct omap_device_board_data serial2_data = {
> +	.id		= 2,
> +	.pads		= serial2_pads,
> +	.pads_cnt	= ARRAY_SIZE(serial2_pads),
> +};
> +
> +static inline void board_serial_init(int is_n800)
> +{
> +	if (is_n800) {
> +		serial1_data.pads = n800_serial1_pads;
> +		serial1_data.pads_cnt = ARRAY_SIZE(n800_serial1_pads);
> +	} else {
> +		serial1_data.pads = n810_serial1_pads;
> +		serial1_data.pads_cnt = ARRAY_SIZE(n810_serial1_pads);
> +	}
> +	omap_serial_init_port(&serial0_data);
> +	omap_serial_init_port(&serial1_data);
> +	omap_serial_init_port(&serial2_data);
> +}
>  #else
> -#define board_mux	NULL
> +static inline void board_serial_init(void)
> +	omap_serial_init();
> +}
>  #endif
>  
>  static void __init n8x0_init_machine(void)
> @@ -772,8 +833,7 @@ static void __init n8x0_init_machine(void)
>  	if (machine_is_nokia_n810())
>  		i2c_register_board_info(2, n810_i2c_board_info_2,
>  					ARRAY_SIZE(n810_i2c_board_info_2));
> -
> -	omap_serial_init();
> +	board_serial_init(machine_is_nokia_n800());
>  	n8x0_onenand_init();
>  	n8x0_mmc_init();
>  	n8x0_usb_init();
>
> --
> To unsubscribe from this list: send the line "unsubscribe linux-omap" in
> the body of a message to majordomo at vger.kernel.org
> More majordomo info at  http://vger.kernel.org/majordomo-info.html