[PATCH] MMC: Fix multiblock SDIO transfers in AT91 MCI

[Nicolas Ferre]

Le 26/11/2010 12:17, Nicolas Ferre :
> Le 25/11/2010 11:11, Yauhen Kharuzhy :
>> The AT91 MCI has special SDIO transfer types: SDIO block and SDIO byte
>> transfers, but at91_mci driver doesn't use them and handles all SDIO
>> transfers as ordinary MMC block transfers. This causes problems for
>> multiple-block SDIO transfers (in particular for 256-bytes blocks).
>>
>> Fix this situation by check opcode for SDIO CMD53 and set transfer
>> type in AT91_MCI_CMDR register properly.
>>
>> This patch was tested with libertas SDIO driver: problem with TX
>> timeouts on big packets was eliminated.
>>
>> Signed-off-by: Yauhen Kharuzhy <yauhen.kharuzhy at promwad.com>
> 
> Signed-off-by: Nicolas Ferre <nicolas.ferre at atmel.com>

Hi Chris,

A little "ping"!

Do you want that I re-send you the patch with relevant S-O-B lines or
you can include them yourself?

Best regards,

>> ---
>>  arch/arm/mach-at91/include/mach/at91_mci.h |    2 ++
>>  drivers/mmc/host/at91_mci.c                |   13 +++++++++----
>>  2 files changed, 11 insertions(+), 4 deletions(-)
>>
>> diff --git a/arch/arm/mach-at91/include/mach/at91_mci.h b/arch/arm/mach-at91/include/mach/at91_mci.h
>> index 57f8ee1..27ac6f5 100644
>> --- a/arch/arm/mach-at91/include/mach/at91_mci.h
>> +++ b/arch/arm/mach-at91/include/mach/at91_mci.h
>> @@ -74,6 +74,8 @@
>>  #define			AT91_MCI_TRTYP_BLOCK	(0 << 19)
>>  #define			AT91_MCI_TRTYP_MULTIPLE	(1 << 19)
>>  #define			AT91_MCI_TRTYP_STREAM	(2 << 19)
>> +#define			AT91_MCI_TRTYP_SDIO_BYTE	(4 << 19)
>> +#define			AT91_MCI_TRTYP_SDIO_BLOCK	(5 << 19)
>>  
>>  #define AT91_MCI_BLKR		0x18		/* Block Register */
>>  #define		AT91_MCI_BLKR_BCNT(n)	((0xffff & (n)) << 0)	/* Block count */
>> diff --git a/drivers/mmc/host/at91_mci.c b/drivers/mmc/host/at91_mci.c
>> index 591ab54..d3e6a96 100644
>> --- a/drivers/mmc/host/at91_mci.c
>> +++ b/drivers/mmc/host/at91_mci.c
>> @@ -69,6 +69,7 @@
>>  #include <linux/highmem.h>
>>  
>>  #include <linux/mmc/host.h>
>> +#include <linux/mmc/sdio.h>
>>  
>>  #include <asm/io.h>
>>  #include <asm/irq.h>
>> @@ -493,10 +494,14 @@ static void at91_mci_send_command(struct at91mci_host *host, struct mmc_command
>>  		else if (data->flags & MMC_DATA_WRITE)
>>  			cmdr |= AT91_MCI_TRCMD_START;
>>  
>> -		if (data->flags & MMC_DATA_STREAM)
>> -			cmdr |= AT91_MCI_TRTYP_STREAM;
>> -		if (data->blocks > 1)
>> -			cmdr |= AT91_MCI_TRTYP_MULTIPLE;
>> +		if (cmd->opcode == SD_IO_RW_EXTENDED) {
>> +			cmdr |= AT91_MCI_TRTYP_SDIO_BLOCK;
>> +		} else {
>> +			if (data->flags & MMC_DATA_STREAM)
>> +				cmdr |= AT91_MCI_TRTYP_STREAM;
>> +			if (data->blocks > 1)
>> +				cmdr |= AT91_MCI_TRTYP_MULTIPLE;
>> +		}
>>  	}
>>  	else {
>>  		block_length = 0;
> 
> 


-- 
Nicolas Ferre