[PATCH v5 08/15] ARM: mxs: Add iomux support

Shawn Guo shawn.guo at freescale.com
Fri Dec 10 03:06:41 EST 2010


MXS-based SoCs implements iomux functions in block PINCTRL.

Signed-off-by: Shawn Guo <shawn.guo at freescale.com>
---
Changes for v5:
 - Change iomux_cfg_t from u64 to u16
 - Add namespace MXS_ to shift, mask, and pad definitions
 - Use SET/CLR register for 1 bit setting
 - Get "if" and "{" at the same line
 - Remove space in middle of tabs
 - Change "setups" to "configures" in comments

Changes for v3:
 - Change iomux_cfg_t to u64 to facilitate adding platform specific
   pad_ctrl settings to an existing pad definition
 - Change inclusion of hardware.h to mxs.h
 - Get iomux_base a hard-assignment in mxs_iomux_setup_pad(), since
   mx23 and mx28 share the common pinctrl base adress and it's only
   used in mxs_iomux_setup_pad().
 - Remove EXPORT_SYMBOL and the static of mxs_iomux_setup_pad()

Changes for v2:
 - Define iomux_cfg_t as u64
 - Turn mxs_iomux_setup_pad() into a static function
 - Fix a bug in mxs_iomux_setup_pad(), muxsel starts at offset 0x100 than 0 of pinctrl block.

 arch/arm/mach-mxs/include/mach/iomux-mx23.h |   29 +++++++
 arch/arm/mach-mxs/include/mach/iomux-mx28.h |   44 ++++++++++
 arch/arm/mach-mxs/include/mach/iomux.h      |  116 +++++++++++++++++++++++++++
 arch/arm/mach-mxs/iomux.c                   |   99 +++++++++++++++++++++++
 4 files changed, 288 insertions(+), 0 deletions(-)
 create mode 100644 arch/arm/mach-mxs/include/mach/iomux-mx23.h
 create mode 100644 arch/arm/mach-mxs/include/mach/iomux-mx28.h
 create mode 100644 arch/arm/mach-mxs/include/mach/iomux.h
 create mode 100644 arch/arm/mach-mxs/iomux.c

diff --git a/arch/arm/mach-mxs/include/mach/iomux-mx23.h b/arch/arm/mach-mxs/include/mach/iomux-mx23.h
new file mode 100644
index 0000000..5a316f4
--- /dev/null
+++ b/arch/arm/mach-mxs/include/mach/iomux-mx23.h
@@ -0,0 +1,29 @@
+/*
+ * Copyright (C) 2009-2010 Amit Kucheria <amit.kucheria at canonical.com>
+ * Copyright (C) 2010 Freescale Semiconductor, Inc.
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+#ifndef __MACH_IOMUX_MX23_H__
+#define __MACH_IOMUX_MX23_H__
+
+#include <mach/iomux.h>
+
+/*
+ * The naming convention for the pad modes is MX23_PAD_<padname>__<padmode>
+ * If <padname> or <padmode> refers to a GPIO, it is named GPIO_<unit>_<num>
+ * See also iomux.h
+ *
+ *							    BANK PIN     MUX            VOL          MA            PULL
+ */
+/* DUART */
+#define MX23_PAD_PWM0__DUART_RX			MXS_IOMUX_PAD(1, 26, PAD_MUXSEL_2,    PAD_VOL_NONE, PAD_4MA,      PAD_NOPULL)
+#define MX23_PAD_PWM1__DUART_TX			MXS_IOMUX_PAD(1, 27, PAD_MUXSEL_2,    PAD_VOL_NONE, PAD_4MA,      PAD_NOPULL)
+
+#endif /* __MACH_IOMUX_MX23_H__ */
diff --git a/arch/arm/mach-mxs/include/mach/iomux-mx28.h b/arch/arm/mach-mxs/include/mach/iomux-mx28.h
new file mode 100644
index 0000000..be8ad2d
--- /dev/null
+++ b/arch/arm/mach-mxs/include/mach/iomux-mx28.h
@@ -0,0 +1,44 @@
+/*
+ * Copyright (C) 2009-2010 Amit Kucheria <amit.kucheria at canonical.com>
+ * Copyright (C) 2010 Freescale Semiconductor, Inc.
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+#ifndef __MACH_IOMUX_MX28_H__
+#define __MACH_IOMUX_MX28_H__
+
+#include <mach/iomux.h>
+
+/*
+ * The naming convention for the pad modes is MX28_PAD_<padname>__<padmode>
+ * If <padname> or <padmode> refers to a GPIO, it is named GPIO_<unit>_<num>
+ * See also iomux.h
+ *
+ *							    BANK PIN     MUX            VOL          MA            PULL
+ */
+/* DUART */
+#define MX28_PAD_PWM0__DUART_RX			MXS_IOMUX_PAD(3, 16, PAD_MUXSEL_2,    PAD_3V3,     PAD_4MA,      PAD_NOPULL)
+#define MX28_PAD_PWM1__DUART_TX			MXS_IOMUX_PAD(3, 17, PAD_MUXSEL_2,    PAD_3V3,     PAD_4MA,      PAD_NOPULL)
+
+/* FEC */
+#define MX28_PAD_ENET0_MDC__ENET0_MDC		MXS_IOMUX_PAD(4, 0,  PAD_MUXSEL_0,    PAD_3V3,     PAD_8MA,      PAD_PULLUP)
+#define MX28_PAD_ENET0_MDIO__ENET0_MDIO		MXS_IOMUX_PAD(4, 1,  PAD_MUXSEL_0,    PAD_3V3,     PAD_8MA,      PAD_PULLUP)
+#define MX28_PAD_ENET0_RX_EN__ENET0_RX_EN	MXS_IOMUX_PAD(4, 2,  PAD_MUXSEL_0,    PAD_3V3,     PAD_8MA,      PAD_PULLUP)
+#define MX28_PAD_ENET0_RXD0__ENET0_RXD0		MXS_IOMUX_PAD(4, 3,  PAD_MUXSEL_0,    PAD_3V3,     PAD_8MA,      PAD_PULLUP)
+#define MX28_PAD_ENET0_RXD1__ENET0_RXD1		MXS_IOMUX_PAD(4, 4,  PAD_MUXSEL_0,    PAD_3V3,     PAD_8MA,      PAD_PULLUP)
+#define MX28_PAD_ENET0_TX_EN__ENET0_TX_EN	MXS_IOMUX_PAD(4, 6,  PAD_MUXSEL_0,    PAD_3V3,     PAD_8MA,      PAD_PULLUP)
+#define MX28_PAD_ENET0_TXD0__ENET0_TXD0		MXS_IOMUX_PAD(4, 7,  PAD_MUXSEL_0,    PAD_3V3,     PAD_8MA,      PAD_PULLUP)
+#define MX28_PAD_ENET0_TXD1__ENET0_TXD1		MXS_IOMUX_PAD(4, 8,  PAD_MUXSEL_0,    PAD_3V3,     PAD_8MA,      PAD_PULLUP)
+#define MX28_PAD_ENET_CLK__ENET_CLK		MXS_IOMUX_PAD(4, 16, PAD_MUXSEL_0,    PAD_3V3,     PAD_8MA,      PAD_PULLUP)
+
+/* GPIO */
+#define MX28_PAD_SSP1_DATA3__GPIO_2_15		MXS_IOMUX_PAD(2, 15, PAD_MUXSEL_GPIO, PAD_3V3,     PAD_4MA,      PAD_NOPULL)
+#define MX28_PAD_ENET0_RX_CLK__GPIO_4_13	MXS_IOMUX_PAD(4, 13, PAD_MUXSEL_GPIO, PAD_3V3,     PAD_4MA,      PAD_NOPULL)
+
+#endif /* __MACH_IOMUX_MX28_H__ */
diff --git a/arch/arm/mach-mxs/include/mach/iomux.h b/arch/arm/mach-mxs/include/mach/iomux.h
new file mode 100644
index 0000000..765b361
--- /dev/null
+++ b/arch/arm/mach-mxs/include/mach/iomux.h
@@ -0,0 +1,116 @@
+/*
+ * Copyright (C) 2009 by Jan Weitzel Phytec Messtechnik GmbH,
+ *			<armlinux at phytec.de>
+ * Copyright (C) 2010 Freescale Semiconductor, Inc. All Rights Reserved.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version 2
+ * of the License, or (at your option) any later version.
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301, USA.
+ */
+
+#ifndef __MACH_MXS_IOMUX_H__
+#define __MACH_MXS_IOMUX_H__
+
+/*
+ * IOMUX/PAD Bit field definitions
+ *
+ * PAD_BANK:	 0..2	(3)
+ * PAD_PIN:	 3..7	(5)
+ * PAD_MUXSEL:	 8..9	(2)
+ * PAD_MA:	10..12	(3)
+ * PAD_VOL:	13..14	(2)
+ * PAD_PULL:	15	(1)
+ */
+typedef u16 iomux_cfg_t;
+
+#define MXS_PAD_BANK_SHIFT	0
+#define MXS_PAD_BANK_MASK	((iomux_cfg_t)0x7 << MXS_PAD_BANK_SHIFT)
+#define MXS_PAD_PIN_SHIFT	3
+#define MXS_PAD_PIN_MASK	((iomux_cfg_t)0x1f << MXS_PAD_PIN_SHIFT)
+#define MXS_PAD_MUXSEL_SHIFT	8
+#define MXS_PAD_MUXSEL_MASK	((iomux_cfg_t)0x3 << MXS_PAD_MUXSEL_SHIFT)
+#define MXS_PAD_MA_SHIFT	10
+#define MXS_PAD_MA_MASK		((iomux_cfg_t)0x7 << MXS_PAD_MA_SHIFT)
+#define MXS_PAD_VOL_SHIFT	13
+#define MXS_PAD_VOL_MASK	((iomux_cfg_t)0x3 << MXS_PAD_VOL_SHIFT)
+#define MXS_PAD_PULL_SHIFT	15
+#define MXS_PAD_PULL_MASK	((iomux_cfg_t)0x1 << MXS_PAD_PULL_SHIFT)
+
+#define MXS_IOMUX_PAD(_bank, _pin, _muxsel, _vol, _ma, _pull)		\
+		(((iomux_cfg_t)(_bank) << MXS_PAD_BANK_SHIFT) |		\
+		((iomux_cfg_t)(_pin) << MXS_PAD_PIN_SHIFT) |		\
+		((iomux_cfg_t)(_muxsel) << MXS_PAD_MUXSEL_SHIFT) |	\
+		((iomux_cfg_t)(_vol) << MXS_PAD_VOL_SHIFT) |		\
+		((iomux_cfg_t)(_ma) << MXS_PAD_MA_SHIFT) |		\
+		((iomux_cfg_t)(_pull) << MXS_PAD_PULL_SHIFT))
+
+#define PAD_MUXSEL_0		0
+#define PAD_MUXSEL_1		1
+#define PAD_MUXSEL_2		2
+#define PAD_MUXSEL_GPIO		3
+
+#define PAD_1V8			0
+#define PAD_3V3			1
+#define PAD_VOL_NONE		2
+
+#define PAD_4MA			0
+#define PAD_8MA			1
+#define PAD_12MA		2
+#define PAD_16MA		3
+#define PAD_MA_NONE		4
+
+#define PAD_NOPULL		0
+#define PAD_PULLUP		1
+
+static inline unsigned int PAD_BANK(iomux_cfg_t pad)
+{
+	return (pad & MXS_PAD_BANK_MASK) >> MXS_PAD_BANK_SHIFT;
+}
+
+static inline unsigned int PAD_PIN(iomux_cfg_t pad)
+{
+	return (pad & MXS_PAD_PIN_MASK) >> MXS_PAD_PIN_SHIFT;
+}
+
+static inline unsigned int PAD_MUXSEL(iomux_cfg_t pad)
+{
+	return (pad & MXS_PAD_MUXSEL_MASK) >> MXS_PAD_MUXSEL_SHIFT;
+}
+
+static inline unsigned int PAD_MA(iomux_cfg_t pad)
+{
+	return (pad & MXS_PAD_MA_MASK) >> MXS_PAD_MA_SHIFT;
+}
+
+static inline unsigned int PAD_VOL(iomux_cfg_t pad)
+{
+	return (pad & MXS_PAD_VOL_MASK) >> MXS_PAD_VOL_SHIFT;
+}
+
+static inline unsigned int PAD_PULL(iomux_cfg_t pad)
+{
+	return (pad & MXS_PAD_PULL_MASK) >> MXS_PAD_PULL_SHIFT;
+}
+
+/*
+ * configures a single pad in the iomuxer
+ */
+int mxs_iomux_setup_pad(iomux_cfg_t pad);
+
+/*
+ * configures multiple pads
+ * convenient way to call the above function with tables
+ */
+int mxs_iomux_setup_multiple_pads(const iomux_cfg_t *pad_list, unsigned count);
+
+#endif /* __MACH_MXS_IOMUX_H__*/
diff --git a/arch/arm/mach-mxs/iomux.c b/arch/arm/mach-mxs/iomux.c
new file mode 100644
index 0000000..8450c65
--- /dev/null
+++ b/arch/arm/mach-mxs/iomux.c
@@ -0,0 +1,99 @@
+/*
+ * Copyright 2004-2006,2010 Freescale Semiconductor, Inc. All Rights Reserved.
+ * Copyright (C) 2008 by Sascha Hauer <kernel at pengutronix.de>
+ * Copyright (C) 2009 by Jan Weitzel Phytec Messtechnik GmbH,
+ *                       <armlinux at phytec.de>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version 2
+ * of the License, or (at your option) any later version.
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301, USA.
+ */
+
+#include <linux/errno.h>
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/string.h>
+#include <linux/gpio.h>
+
+#include <asm/mach/map.h>
+
+#include <mach/mxs.h>
+#include <mach/iomux.h>
+
+/*
+ * configures a single pad in the iomuxer
+ */
+int mxs_iomux_setup_pad(iomux_cfg_t pad)
+{
+	u32 reg, ofs, bp, bm;
+	void __iomem *iomux_base = MXS_IO_ADDRESS(MXS_PINCTRL_BASE_ADDR);
+
+	/* muxsel */
+	ofs = 0x100;
+	ofs += PAD_BANK(pad) * 0x20 + PAD_PIN(pad) / 16 * 0x10;
+	bp = PAD_PIN(pad) % 16 * 2;
+	bm = 0x3 << bp;
+	reg = __raw_readl(iomux_base + ofs);
+	reg &= ~bm;
+	reg |= PAD_MUXSEL(pad) << bp;
+	__raw_writel(reg, iomux_base + ofs);
+
+	/* drive */
+	ofs = cpu_is_mx23() ? 0x200 : 0x300;
+	ofs += PAD_BANK(pad) * 0x40 + PAD_PIN(pad) / 8 * 0x10;
+	/* mA */
+	if (PAD_MA(pad) != PAD_MA_NONE) {
+		bp = PAD_PIN(pad) % 8 * 4;
+		bm = 0x3 << bp;
+		reg = __raw_readl(iomux_base + ofs);
+		reg &= ~bm;
+		reg |= PAD_MA(pad) << bp;
+		__raw_writel(reg, iomux_base + ofs);
+	}
+	/* vol */
+	if (PAD_VOL(pad) != PAD_VOL_NONE) {
+		bp = PAD_PIN(pad) % 8 * 4 + 2;
+		if (PAD_VOL(pad))
+			__raw_writel(1 << bp, iomux_base + ofs + MXS_SET_ADDR);
+		else
+			__raw_writel(1 << bp, iomux_base + ofs + MXS_CLR_ADDR);
+	}
+
+	/* pull */
+	ofs = cpu_is_mx23() ? 0x400 : 0x600;
+	ofs += PAD_BANK(pad) * 0x10;
+	bp = PAD_PIN(pad);
+	if (PAD_PULL(pad))
+		__raw_writel(1 << bp, iomux_base + ofs + MXS_SET_ADDR);
+	else
+		__raw_writel(1 << bp, iomux_base + ofs + MXS_CLR_ADDR);
+
+	return 0;
+}
+
+int mxs_iomux_setup_multiple_pads(const iomux_cfg_t *pad_list, unsigned count)
+{
+	const iomux_cfg_t *p = pad_list;
+	int i;
+	int ret;
+
+	for (i = 0; i < count; i++) {
+		ret = mxs_iomux_setup_pad(*p);
+		if (ret)
+			return ret;
+		p++;
+	}
+
+	return 0;
+}
-- 
1.7.1





More information about the linux-arm-kernel mailing list