[PATCH] mach-at91: Support for gms board added.
Igor Plyatov
plyatov at gmail.com
Mon Dec 6 14:32:18 EST 2010
The gms is a board from GeoSIG Ltd. It is based on the Stamp9G20 module from Taskit.
Signed-off-by: Igor Plyatov <plyatov at gmail.com>
---
arch/arm/configs/stamp9g20gms_defconfig | 1830 +++++++++++++++++++++++++++++++
arch/arm/mach-at91/Kconfig | 7 +
arch/arm/mach-at91/Makefile | 1 +
arch/arm/mach-at91/board-stamp9g20gms.c | 720 ++++++++++++
arch/arm/mach-at91/include/mach/gms.h | 27 +
5 files changed, 2585 insertions(+), 0 deletions(-)
create mode 100644 arch/arm/configs/stamp9g20gms_defconfig
create mode 100644 arch/arm/mach-at91/board-stamp9g20gms.c
create mode 100644 arch/arm/mach-at91/include/mach/gms.h
diff --git a/arch/arm/configs/stamp9g20gms_defconfig b/arch/arm/configs/stamp9g20gms_defconfig
new file mode 100644
index 0000000..430b57f
--- /dev/null
+++ b/arch/arm/configs/stamp9g20gms_defconfig
@@ -0,0 +1,1830 @@
+#
+# Automatically generated make config: don't edit
+# Linux/arm 2.6.37-rc4 Kernel Configuration
+# Mon Dec 6 22:00:26 2010
+#
+CONFIG_ARM=y
+CONFIG_SYS_SUPPORTS_APM_EMULATION=y
+CONFIG_GENERIC_GPIO=y
+# CONFIG_ARCH_USES_GETTIMEOFFSET is not set
+CONFIG_GENERIC_CLOCKEVENTS=y
+CONFIG_HAVE_PROC_CPU=y
+CONFIG_GENERIC_HARDIRQS=y
+CONFIG_STACKTRACE_SUPPORT=y
+CONFIG_HAVE_LATENCYTOP_SUPPORT=y
+CONFIG_LOCKDEP_SUPPORT=y
+CONFIG_TRACE_IRQFLAGS_SUPPORT=y
+CONFIG_HARDIRQS_SW_RESEND=y
+CONFIG_GENERIC_IRQ_PROBE=y
+CONFIG_RWSEM_GENERIC_SPINLOCK=y
+CONFIG_ARCH_HAS_CPU_IDLE_WAIT=y
+CONFIG_GENERIC_HWEIGHT=y
+CONFIG_GENERIC_CALIBRATE_DELAY=y
+CONFIG_NEED_DMA_MAP_STATE=y
+CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
+CONFIG_VECTORS_BASE=0xffff0000
+CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
+CONFIG_HAVE_IRQ_WORK=y
+
+#
+# General setup
+#
+CONFIG_EXPERIMENTAL=y
+CONFIG_BROKEN_ON_SMP=y
+CONFIG_LOCK_KERNEL=y
+CONFIG_INIT_ENV_ARG_LIMIT=32
+CONFIG_CROSS_COMPILE=""
+CONFIG_LOCALVERSION=""
+# CONFIG_LOCALVERSION_AUTO is not set
+CONFIG_HAVE_KERNEL_GZIP=y
+CONFIG_HAVE_KERNEL_LZMA=y
+CONFIG_HAVE_KERNEL_LZO=y
+CONFIG_KERNEL_GZIP=y
+# CONFIG_KERNEL_LZMA is not set
+# CONFIG_KERNEL_LZO is not set
+CONFIG_SWAP=y
+CONFIG_SYSVIPC=y
+CONFIG_SYSVIPC_SYSCTL=y
+# CONFIG_POSIX_MQUEUE is not set
+# CONFIG_BSD_PROCESS_ACCT is not set
+# CONFIG_TASKSTATS is not set
+# CONFIG_AUDIT is not set
+# CONFIG_HAVE_GENERIC_HARDIRQS is not set
+# CONFIG_SPARSE_IRQ is not set
+
+#
+# RCU Subsystem
+#
+CONFIG_TREE_PREEMPT_RCU=y
+# CONFIG_TINY_RCU is not set
+# CONFIG_TINY_PREEMPT_RCU is not set
+CONFIG_PREEMPT_RCU=y
+# CONFIG_RCU_TRACE is not set
+CONFIG_RCU_FANOUT=32
+# CONFIG_RCU_FANOUT_EXACT is not set
+# CONFIG_TREE_RCU_TRACE is not set
+# CONFIG_IKCONFIG is not set
+CONFIG_LOG_BUF_SHIFT=14
+# CONFIG_CGROUPS is not set
+CONFIG_NAMESPACES=y
+# CONFIG_UTS_NS is not set
+# CONFIG_IPC_NS is not set
+# CONFIG_USER_NS is not set
+# CONFIG_PID_NS is not set
+# CONFIG_NET_NS is not set
+# CONFIG_SYSFS_DEPRECATED is not set
+# CONFIG_RELAY is not set
+CONFIG_BLK_DEV_INITRD=y
+CONFIG_INITRAMFS_SOURCE=""
+CONFIG_RD_GZIP=y
+CONFIG_RD_BZIP2=y
+CONFIG_RD_LZMA=y
+CONFIG_RD_LZO=y
+CONFIG_CC_OPTIMIZE_FOR_SIZE=y
+CONFIG_SYSCTL=y
+CONFIG_ANON_INODES=y
+# CONFIG_EMBEDDED is not set
+CONFIG_UID16=y
+CONFIG_SYSCTL_SYSCALL=y
+CONFIG_KALLSYMS=y
+# CONFIG_KALLSYMS_EXTRA_PASS is not set
+CONFIG_HOTPLUG=y
+CONFIG_PRINTK=y
+CONFIG_BUG=y
+CONFIG_ELF_CORE=y
+CONFIG_BASE_FULL=y
+CONFIG_FUTEX=y
+CONFIG_EPOLL=y
+CONFIG_SIGNALFD=y
+CONFIG_TIMERFD=y
+CONFIG_EVENTFD=y
+CONFIG_SHMEM=y
+CONFIG_AIO=y
+CONFIG_HAVE_PERF_EVENTS=y
+CONFIG_PERF_USE_VMALLOC=y
+
+#
+# Kernel Performance Events And Counters
+#
+# CONFIG_PERF_EVENTS is not set
+# CONFIG_PERF_COUNTERS is not set
+CONFIG_VM_EVENT_COUNTERS=y
+CONFIG_COMPAT_BRK=y
+CONFIG_SLAB=y
+# CONFIG_SLUB is not set
+# CONFIG_PROFILING is not set
+CONFIG_HAVE_OPROFILE=y
+# CONFIG_KPROBES is not set
+CONFIG_HAVE_KPROBES=y
+CONFIG_HAVE_KRETPROBES=y
+CONFIG_HAVE_REGS_AND_STACK_ACCESS_API=y
+CONFIG_HAVE_CLK=y
+
+#
+# GCOV-based kernel profiling
+#
+CONFIG_HAVE_GENERIC_DMA_COHERENT=y
+CONFIG_SLABINFO=y
+CONFIG_RT_MUTEXES=y
+CONFIG_BASE_SMALL=0
+CONFIG_MODULES=y
+# CONFIG_MODULE_FORCE_LOAD is not set
+CONFIG_MODULE_UNLOAD=y
+# CONFIG_MODULE_FORCE_UNLOAD is not set
+# CONFIG_MODVERSIONS is not set
+# CONFIG_MODULE_SRCVERSION_ALL is not set
+CONFIG_BLOCK=y
+CONFIG_LBDAF=y
+# CONFIG_BLK_DEV_BSG is not set
+# CONFIG_BLK_DEV_INTEGRITY is not set
+
+#
+# IO Schedulers
+#
+CONFIG_IOSCHED_NOOP=y
+# CONFIG_IOSCHED_DEADLINE is not set
+CONFIG_IOSCHED_CFQ=y
+CONFIG_DEFAULT_CFQ=y
+# CONFIG_DEFAULT_NOOP is not set
+CONFIG_DEFAULT_IOSCHED="cfq"
+# CONFIG_INLINE_SPIN_TRYLOCK is not set
+# CONFIG_INLINE_SPIN_TRYLOCK_BH is not set
+# CONFIG_INLINE_SPIN_LOCK is not set
+# CONFIG_INLINE_SPIN_LOCK_BH is not set
+# CONFIG_INLINE_SPIN_LOCK_IRQ is not set
+# CONFIG_INLINE_SPIN_LOCK_IRQSAVE is not set
+# CONFIG_INLINE_SPIN_UNLOCK is not set
+# CONFIG_INLINE_SPIN_UNLOCK_BH is not set
+# CONFIG_INLINE_SPIN_UNLOCK_IRQ is not set
+# CONFIG_INLINE_SPIN_UNLOCK_IRQRESTORE is not set
+# CONFIG_INLINE_READ_TRYLOCK is not set
+# CONFIG_INLINE_READ_LOCK is not set
+# CONFIG_INLINE_READ_LOCK_BH is not set
+# CONFIG_INLINE_READ_LOCK_IRQ is not set
+# CONFIG_INLINE_READ_LOCK_IRQSAVE is not set
+# CONFIG_INLINE_READ_UNLOCK is not set
+# CONFIG_INLINE_READ_UNLOCK_BH is not set
+# CONFIG_INLINE_READ_UNLOCK_IRQ is not set
+# CONFIG_INLINE_READ_UNLOCK_IRQRESTORE is not set
+# CONFIG_INLINE_WRITE_TRYLOCK is not set
+# CONFIG_INLINE_WRITE_LOCK is not set
+# CONFIG_INLINE_WRITE_LOCK_BH is not set
+# CONFIG_INLINE_WRITE_LOCK_IRQ is not set
+# CONFIG_INLINE_WRITE_LOCK_IRQSAVE is not set
+# CONFIG_INLINE_WRITE_UNLOCK is not set
+# CONFIG_INLINE_WRITE_UNLOCK_BH is not set
+# CONFIG_INLINE_WRITE_UNLOCK_IRQ is not set
+# CONFIG_INLINE_WRITE_UNLOCK_IRQRESTORE is not set
+# CONFIG_MUTEX_SPIN_ON_OWNER is not set
+CONFIG_FREEZER=y
+
+#
+# System Type
+#
+CONFIG_MMU=y
+# CONFIG_ARCH_AAEC2000 is not set
+# CONFIG_ARCH_INTEGRATOR is not set
+# CONFIG_ARCH_REALVIEW is not set
+# CONFIG_ARCH_VERSATILE is not set
+# CONFIG_ARCH_VEXPRESS is not set
+CONFIG_ARCH_AT91=y
+# CONFIG_ARCH_BCMRING is not set
+# CONFIG_ARCH_CLPS711X is not set
+# CONFIG_ARCH_CNS3XXX is not set
+# CONFIG_ARCH_GEMINI is not set
+# CONFIG_ARCH_EBSA110 is not set
+# CONFIG_ARCH_EP93XX is not set
+# CONFIG_ARCH_FOOTBRIDGE is not set
+# CONFIG_ARCH_MXC is not set
+# CONFIG_ARCH_STMP3XXX is not set
+# CONFIG_ARCH_NETX is not set
+# CONFIG_ARCH_H720X is not set
+# CONFIG_ARCH_IOP13XX is not set
+# CONFIG_ARCH_IOP32X is not set
+# CONFIG_ARCH_IOP33X is not set
+# CONFIG_ARCH_IXP23XX is not set
+# CONFIG_ARCH_IXP2000 is not set
+# CONFIG_ARCH_IXP4XX is not set
+# CONFIG_ARCH_DOVE is not set
+# CONFIG_ARCH_KIRKWOOD is not set
+# CONFIG_ARCH_LOKI is not set
+# CONFIG_ARCH_LPC32XX is not set
+# CONFIG_ARCH_MV78XX0 is not set
+# CONFIG_ARCH_ORION5X is not set
+# CONFIG_ARCH_MMP is not set
+# CONFIG_ARCH_KS8695 is not set
+# CONFIG_ARCH_NS9XXX is not set
+# CONFIG_ARCH_W90X900 is not set
+# CONFIG_ARCH_NUC93X is not set
+# CONFIG_ARCH_TEGRA is not set
+# CONFIG_ARCH_PNX4008 is not set
+# CONFIG_ARCH_PXA is not set
+# CONFIG_ARCH_MSM is not set
+# CONFIG_ARCH_SHMOBILE is not set
+# CONFIG_ARCH_RPC is not set
+# CONFIG_ARCH_SA1100 is not set
+# CONFIG_ARCH_S3C2410 is not set
+# CONFIG_ARCH_S3C64XX is not set
+# CONFIG_ARCH_S5P64X0 is not set
+# CONFIG_ARCH_S5P6442 is not set
+# CONFIG_ARCH_S5PC100 is not set
+# CONFIG_ARCH_S5PV210 is not set
+# CONFIG_ARCH_S5PV310 is not set
+# CONFIG_ARCH_SHARK is not set
+# CONFIG_ARCH_TCC_926 is not set
+# CONFIG_ARCH_LH7A40X is not set
+# CONFIG_ARCH_U300 is not set
+# CONFIG_ARCH_U8500 is not set
+# CONFIG_ARCH_NOMADIK is not set
+# CONFIG_ARCH_DAVINCI is not set
+# CONFIG_ARCH_OMAP is not set
+# CONFIG_PLAT_SPEAR is not set
+CONFIG_HAVE_AT91_USART3=y
+CONFIG_HAVE_AT91_USART4=y
+CONFIG_HAVE_AT91_USART5=y
+
+#
+# Atmel AT91 System-on-Chip
+#
+# CONFIG_ARCH_AT91RM9200 is not set
+# CONFIG_ARCH_AT91SAM9260 is not set
+# CONFIG_ARCH_AT91SAM9261 is not set
+# CONFIG_ARCH_AT91SAM9G10 is not set
+# CONFIG_ARCH_AT91SAM9263 is not set
+# CONFIG_ARCH_AT91SAM9RL is not set
+CONFIG_ARCH_AT91SAM9G20=y
+# CONFIG_ARCH_AT91SAM9G45 is not set
+# CONFIG_ARCH_AT91CAP9 is not set
+# CONFIG_ARCH_AT572D940HF is not set
+# CONFIG_ARCH_AT91X40 is not set
+CONFIG_AT91_PMC_UNIT=y
+
+#
+# AT91SAM9G20 Board Type
+#
+# CONFIG_MACH_AT91SAM9G20EK is not set
+# CONFIG_MACH_CPU9G20 is not set
+# CONFIG_MACH_PORTUXG20 is not set
+# CONFIG_MACH_STAMP9G20 is not set
+# CONFIG_MACH_PCONTROL_G20 is not set
+CONFIG_MACH_STAMP9G20GMS=y
+
+#
+# AT91SAM9260/AT91SAM9G20 boards
+#
+# CONFIG_MACH_SNAPPER_9260 is not set
+
+#
+# AT91 Board Options
+#
+
+#
+# AT91 Feature Selections
+#
+CONFIG_AT91_PROGRAMMABLE_CLOCKS=y
+CONFIG_AT91_SLOW_CLOCK=y
+CONFIG_AT91_TIMER_HZ=100
+CONFIG_AT91_EARLY_DBGU=y
+# CONFIG_AT91_EARLY_USART0 is not set
+# CONFIG_AT91_EARLY_USART1 is not set
+# CONFIG_AT91_EARLY_USART2 is not set
+# CONFIG_AT91_EARLY_USART3 is not set
+# CONFIG_AT91_EARLY_USART4 is not set
+# CONFIG_AT91_EARLY_USART5 is not set
+
+#
+# Processor Type
+#
+CONFIG_CPU_ARM926T=y
+CONFIG_CPU_32v5=y
+CONFIG_CPU_ABRT_EV5TJ=y
+CONFIG_CPU_PABRT_LEGACY=y
+CONFIG_CPU_CACHE_VIVT=y
+CONFIG_CPU_COPY_V4WB=y
+CONFIG_CPU_TLB_V4WBI=y
+CONFIG_CPU_CP15=y
+CONFIG_CPU_CP15_MMU=y
+
+#
+# Processor Features
+#
+CONFIG_ARM_THUMB=y
+# CONFIG_CPU_ICACHE_DISABLE is not set
+# CONFIG_CPU_DCACHE_DISABLE is not set
+# CONFIG_CPU_DCACHE_WRITETHROUGH is not set
+# CONFIG_CPU_CACHE_ROUND_ROBIN is not set
+CONFIG_ARM_L1_CACHE_SHIFT=5
+
+#
+# Bus support
+#
+# CONFIG_PCI_SYSCALL is not set
+# CONFIG_ARCH_SUPPORTS_MSI is not set
+# CONFIG_PCCARD is not set
+
+#
+# Kernel Features
+#
+CONFIG_TICK_ONESHOT=y
+CONFIG_NO_HZ=y
+CONFIG_HIGH_RES_TIMERS=y
+CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
+CONFIG_VMSPLIT_3G=y
+# CONFIG_VMSPLIT_2G is not set
+# CONFIG_VMSPLIT_1G is not set
+CONFIG_PAGE_OFFSET=0xC0000000
+# CONFIG_PREEMPT_NONE is not set
+# CONFIG_PREEMPT_VOLUNTARY is not set
+CONFIG_PREEMPT=y
+CONFIG_HZ=100
+CONFIG_AEABI=y
+# CONFIG_OABI_COMPAT is not set
+# CONFIG_ARCH_SPARSEMEM_DEFAULT is not set
+# CONFIG_ARCH_SELECT_MEMORY_MODEL is not set
+# CONFIG_HIGHMEM is not set
+CONFIG_SELECT_MEMORY_MODEL=y
+CONFIG_FLATMEM_MANUAL=y
+CONFIG_FLATMEM=y
+CONFIG_FLAT_NODE_MEM_MAP=y
+CONFIG_HAVE_MEMBLOCK=y
+CONFIG_PAGEFLAGS_EXTENDED=y
+CONFIG_SPLIT_PTLOCK_CPUS=999999
+# CONFIG_PHYS_ADDR_T_64BIT is not set
+CONFIG_ZONE_DMA_FLAG=0
+CONFIG_VIRT_TO_BUS=y
+# CONFIG_KSM is not set
+CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
+CONFIG_NEED_PER_CPU_KM=y
+CONFIG_FORCE_MAX_ZONEORDER=11
+# CONFIG_LEDS is not set
+CONFIG_ALIGNMENT_TRAP=y
+# CONFIG_UACCESS_WITH_MEMCPY is not set
+# CONFIG_SECCOMP is not set
+# CONFIG_CC_STACKPROTECTOR is not set
+# CONFIG_DEPRECATED_PARAM_STRUCT is not set
+
+#
+# Boot options
+#
+CONFIG_ZBOOT_ROM_TEXT=0x0
+CONFIG_ZBOOT_ROM_BSS=0x0
+CONFIG_CMDLINE="mem=64M console=ttyS0,115200 initrd=0x21100000,3145728 root=/dev/ram0 rw"
+# CONFIG_CMDLINE_FORCE is not set
+# CONFIG_XIP_KERNEL is not set
+CONFIG_KEXEC=y
+CONFIG_ATAGS_PROC=y
+# CONFIG_AUTO_ZRELADDR is not set
+
+#
+# CPU Power Management
+#
+CONFIG_CPU_IDLE=y
+CONFIG_CPU_IDLE_GOV_LADDER=y
+CONFIG_CPU_IDLE_GOV_MENU=y
+
+#
+# Floating point emulation
+#
+
+#
+# At least one emulation must be selected
+#
+# CONFIG_VFP is not set
+
+#
+# Userspace binary formats
+#
+CONFIG_BINFMT_ELF=y
+# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
+CONFIG_HAVE_AOUT=y
+# CONFIG_BINFMT_AOUT is not set
+# CONFIG_BINFMT_MISC is not set
+
+#
+# Power management options
+#
+CONFIG_PM=y
+# CONFIG_PM_DEBUG is not set
+CONFIG_PM_SLEEP=y
+CONFIG_SUSPEND_NVS=y
+CONFIG_SUSPEND=y
+CONFIG_SUSPEND_FREEZER=y
+# CONFIG_APM_EMULATION is not set
+# CONFIG_PM_RUNTIME is not set
+CONFIG_PM_OPS=y
+CONFIG_ARCH_SUSPEND_POSSIBLE=y
+CONFIG_NET=y
+
+#
+# Networking options
+#
+CONFIG_PACKET=y
+CONFIG_UNIX=y
+# CONFIG_NET_KEY is not set
+CONFIG_INET=y
+# CONFIG_IP_MULTICAST is not set
+# CONFIG_IP_ADVANCED_ROUTER is not set
+CONFIG_IP_FIB_HASH=y
+# CONFIG_IP_PNP is not set
+# CONFIG_NET_IPIP is not set
+# CONFIG_NET_IPGRE_DEMUX is not set
+# CONFIG_ARPD is not set
+# CONFIG_SYN_COOKIES is not set
+# CONFIG_INET_AH is not set
+# CONFIG_INET_ESP is not set
+# CONFIG_INET_IPCOMP is not set
+# CONFIG_INET_XFRM_TUNNEL is not set
+# CONFIG_INET_TUNNEL is not set
+# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
+# CONFIG_INET_XFRM_MODE_TUNNEL is not set
+# CONFIG_INET_XFRM_MODE_BEET is not set
+# CONFIG_INET_LRO is not set
+CONFIG_INET_DIAG=y
+CONFIG_INET_TCP_DIAG=y
+# CONFIG_TCP_CONG_ADVANCED is not set
+CONFIG_TCP_CONG_CUBIC=y
+CONFIG_DEFAULT_TCP_CONG="cubic"
+# CONFIG_TCP_MD5SIG is not set
+# CONFIG_IPV6 is not set
+# CONFIG_NETWORK_SECMARK is not set
+# CONFIG_NETWORK_PHY_TIMESTAMPING is not set
+CONFIG_NETFILTER=y
+# CONFIG_NETFILTER_DEBUG is not set
+CONFIG_NETFILTER_ADVANCED=y
+
+#
+# Core Netfilter Configuration
+#
+CONFIG_NETFILTER_NETLINK=m
+# CONFIG_NETFILTER_NETLINK_QUEUE is not set
+CONFIG_NETFILTER_NETLINK_LOG=m
+CONFIG_NF_CONNTRACK=m
+CONFIG_NF_CONNTRACK_MARK=y
+# CONFIG_NF_CONNTRACK_EVENTS is not set
+# CONFIG_NF_CT_PROTO_DCCP is not set
+CONFIG_NF_CT_PROTO_SCTP=m
+CONFIG_NF_CT_PROTO_UDPLITE=m
+# CONFIG_NF_CONNTRACK_AMANDA is not set
+CONFIG_NF_CONNTRACK_FTP=m
+# CONFIG_NF_CONNTRACK_H323 is not set
+CONFIG_NF_CONNTRACK_IRC=m
+# CONFIG_NF_CONNTRACK_NETBIOS_NS is not set
+# CONFIG_NF_CONNTRACK_PPTP is not set
+# CONFIG_NF_CONNTRACK_SANE is not set
+CONFIG_NF_CONNTRACK_SIP=m
+# CONFIG_NF_CONNTRACK_TFTP is not set
+CONFIG_NF_CT_NETLINK=m
+# CONFIG_NETFILTER_TPROXY is not set
+CONFIG_NETFILTER_XTABLES=m
+
+#
+# Xtables combined modules
+#
+CONFIG_NETFILTER_XT_MARK=m
+CONFIG_NETFILTER_XT_CONNMARK=m
+
+#
+# Xtables targets
+#
+# CONFIG_NETFILTER_XT_TARGET_CHECKSUM is not set
+# CONFIG_NETFILTER_XT_TARGET_CLASSIFY is not set
+# CONFIG_NETFILTER_XT_TARGET_CONNMARK is not set
+# CONFIG_NETFILTER_XT_TARGET_CT is not set
+# CONFIG_NETFILTER_XT_TARGET_DSCP is not set
+CONFIG_NETFILTER_XT_TARGET_HL=m
+# CONFIG_NETFILTER_XT_TARGET_IDLETIMER is not set
+# CONFIG_NETFILTER_XT_TARGET_LED is not set
+# CONFIG_NETFILTER_XT_TARGET_MARK is not set
+# CONFIG_NETFILTER_XT_TARGET_NFLOG is not set
+# CONFIG_NETFILTER_XT_TARGET_NFQUEUE is not set
+# CONFIG_NETFILTER_XT_TARGET_NOTRACK is not set
+# CONFIG_NETFILTER_XT_TARGET_RATEEST is not set
+# CONFIG_NETFILTER_XT_TARGET_TEE is not set
+# CONFIG_NETFILTER_XT_TARGET_TRACE is not set
+# CONFIG_NETFILTER_XT_TARGET_TCPMSS is not set
+# CONFIG_NETFILTER_XT_TARGET_TCPOPTSTRIP is not set
+
+#
+# Xtables matches
+#
+# CONFIG_NETFILTER_XT_MATCH_CLUSTER is not set
+# CONFIG_NETFILTER_XT_MATCH_COMMENT is not set
+# CONFIG_NETFILTER_XT_MATCH_CONNBYTES is not set
+# CONFIG_NETFILTER_XT_MATCH_CONNLIMIT is not set
+# CONFIG_NETFILTER_XT_MATCH_CONNMARK is not set
+# CONFIG_NETFILTER_XT_MATCH_CONNTRACK is not set
+# CONFIG_NETFILTER_XT_MATCH_CPU is not set
+# CONFIG_NETFILTER_XT_MATCH_DCCP is not set
+# CONFIG_NETFILTER_XT_MATCH_DSCP is not set
+# CONFIG_NETFILTER_XT_MATCH_ESP is not set
+# CONFIG_NETFILTER_XT_MATCH_HASHLIMIT is not set
+# CONFIG_NETFILTER_XT_MATCH_HELPER is not set
+CONFIG_NETFILTER_XT_MATCH_HL=m
+# CONFIG_NETFILTER_XT_MATCH_IPRANGE is not set
+# CONFIG_NETFILTER_XT_MATCH_LENGTH is not set
+# CONFIG_NETFILTER_XT_MATCH_LIMIT is not set
+# CONFIG_NETFILTER_XT_MATCH_MAC is not set
+# CONFIG_NETFILTER_XT_MATCH_MARK is not set
+# CONFIG_NETFILTER_XT_MATCH_MULTIPORT is not set
+# CONFIG_NETFILTER_XT_MATCH_OSF is not set
+# CONFIG_NETFILTER_XT_MATCH_OWNER is not set
+# CONFIG_NETFILTER_XT_MATCH_PKTTYPE is not set
+# CONFIG_NETFILTER_XT_MATCH_QUOTA is not set
+# CONFIG_NETFILTER_XT_MATCH_RATEEST is not set
+# CONFIG_NETFILTER_XT_MATCH_REALM is not set
+# CONFIG_NETFILTER_XT_MATCH_RECENT is not set
+# CONFIG_NETFILTER_XT_MATCH_SCTP is not set
+CONFIG_NETFILTER_XT_MATCH_STATE=m
+# CONFIG_NETFILTER_XT_MATCH_STATISTIC is not set
+# CONFIG_NETFILTER_XT_MATCH_STRING is not set
+# CONFIG_NETFILTER_XT_MATCH_TCPMSS is not set
+# CONFIG_NETFILTER_XT_MATCH_TIME is not set
+# CONFIG_NETFILTER_XT_MATCH_U32 is not set
+# CONFIG_IP_VS is not set
+
+#
+# IP: Netfilter Configuration
+#
+CONFIG_NF_DEFRAG_IPV4=m
+CONFIG_NF_CONNTRACK_IPV4=m
+CONFIG_NF_CONNTRACK_PROC_COMPAT=y
+# CONFIG_IP_NF_QUEUE is not set
+CONFIG_IP_NF_IPTABLES=m
+CONFIG_IP_NF_MATCH_ADDRTYPE=m
+CONFIG_IP_NF_MATCH_AH=m
+CONFIG_IP_NF_MATCH_ECN=m
+CONFIG_IP_NF_MATCH_TTL=m
+CONFIG_IP_NF_FILTER=m
+CONFIG_IP_NF_TARGET_REJECT=m
+CONFIG_IP_NF_TARGET_LOG=m
+CONFIG_IP_NF_TARGET_ULOG=m
+CONFIG_NF_NAT=m
+CONFIG_NF_NAT_NEEDED=y
+CONFIG_IP_NF_TARGET_MASQUERADE=m
+CONFIG_IP_NF_TARGET_NETMAP=m
+CONFIG_IP_NF_TARGET_REDIRECT=m
+CONFIG_NF_NAT_SNMP_BASIC=m
+CONFIG_NF_NAT_PROTO_UDPLITE=m
+CONFIG_NF_NAT_PROTO_SCTP=m
+CONFIG_NF_NAT_FTP=m
+CONFIG_NF_NAT_IRC=m
+# CONFIG_NF_NAT_TFTP is not set
+# CONFIG_NF_NAT_AMANDA is not set
+# CONFIG_NF_NAT_PPTP is not set
+# CONFIG_NF_NAT_H323 is not set
+CONFIG_NF_NAT_SIP=m
+CONFIG_IP_NF_MANGLE=m
+CONFIG_IP_NF_TARGET_CLUSTERIP=m
+CONFIG_IP_NF_TARGET_ECN=m
+CONFIG_IP_NF_TARGET_TTL=m
+CONFIG_IP_NF_RAW=m
+CONFIG_IP_NF_ARPTABLES=m
+CONFIG_IP_NF_ARPFILTER=m
+CONFIG_IP_NF_ARP_MANGLE=m
+# CONFIG_IP_DCCP is not set
+# CONFIG_IP_SCTP is not set
+# CONFIG_RDS is not set
+# CONFIG_TIPC is not set
+# CONFIG_ATM is not set
+# CONFIG_L2TP is not set
+# CONFIG_BRIDGE is not set
+# CONFIG_NET_DSA is not set
+# CONFIG_VLAN_8021Q is not set
+# CONFIG_DECNET is not set
+# CONFIG_LLC2 is not set
+# CONFIG_IPX is not set
+# CONFIG_ATALK is not set
+# CONFIG_X25 is not set
+# CONFIG_LAPB is not set
+# CONFIG_ECONET is not set
+# CONFIG_WAN_ROUTER is not set
+# CONFIG_PHONET is not set
+# CONFIG_IEEE802154 is not set
+# CONFIG_NET_SCHED is not set
+# CONFIG_DCB is not set
+
+#
+# Network testing
+#
+# CONFIG_NET_PKTGEN is not set
+# CONFIG_HAMRADIO is not set
+# CONFIG_CAN is not set
+# CONFIG_IRDA is not set
+# CONFIG_BT is not set
+# CONFIG_AF_RXRPC is not set
+CONFIG_WIRELESS=y
+CONFIG_WEXT_CORE=y
+CONFIG_WEXT_PROC=y
+CONFIG_CFG80211=y
+# CONFIG_NL80211_TESTMODE is not set
+# CONFIG_CFG80211_DEVELOPER_WARNINGS is not set
+# CONFIG_CFG80211_REG_DEBUG is not set
+CONFIG_CFG80211_DEFAULT_PS=y
+# CONFIG_CFG80211_INTERNAL_REGDB is not set
+CONFIG_CFG80211_WEXT=y
+CONFIG_WIRELESS_EXT_SYSFS=y
+CONFIG_LIB80211=y
+# CONFIG_LIB80211_DEBUG is not set
+CONFIG_MAC80211=y
+CONFIG_MAC80211_HAS_RC=y
+CONFIG_MAC80211_RC_MINSTREL=y
+CONFIG_MAC80211_RC_MINSTREL_HT=y
+CONFIG_MAC80211_RC_DEFAULT_MINSTREL=y
+CONFIG_MAC80211_RC_DEFAULT="minstrel_ht"
+# CONFIG_MAC80211_MESH is not set
+CONFIG_MAC80211_LEDS=y
+# CONFIG_MAC80211_DEBUG_MENU is not set
+# CONFIG_WIMAX is not set
+# CONFIG_RFKILL is not set
+# CONFIG_NET_9P is not set
+# CONFIG_CAIF is not set
+# CONFIG_CEPH_LIB is not set
+
+#
+# Device Drivers
+#
+
+#
+# Generic Driver Options
+#
+CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+# CONFIG_DEVTMPFS is not set
+CONFIG_STANDALONE=y
+CONFIG_PREVENT_FIRMWARE_BUILD=y
+CONFIG_FW_LOADER=y
+CONFIG_FIRMWARE_IN_KERNEL=y
+CONFIG_EXTRA_FIRMWARE=""
+# CONFIG_SYS_HYPERVISOR is not set
+# CONFIG_CONNECTOR is not set
+CONFIG_MTD=y
+# CONFIG_MTD_DEBUG is not set
+# CONFIG_MTD_TESTS is not set
+CONFIG_MTD_CONCAT=y
+CONFIG_MTD_PARTITIONS=y
+# CONFIG_MTD_REDBOOT_PARTS is not set
+CONFIG_MTD_CMDLINE_PARTS=y
+# CONFIG_MTD_AFS_PARTS is not set
+# CONFIG_MTD_AR7_PARTS is not set
+
+#
+# User Modules And Translation Layers
+#
+CONFIG_MTD_CHAR=y
+CONFIG_MTD_BLKDEVS=y
+CONFIG_MTD_BLOCK=y
+# CONFIG_FTL is not set
+# CONFIG_NFTL is not set
+# CONFIG_INFTL is not set
+# CONFIG_RFD_FTL is not set
+# CONFIG_SSFDC is not set
+# CONFIG_SM_FTL is not set
+# CONFIG_MTD_OOPS is not set
+
+#
+# RAM/ROM/Flash chip drivers
+#
+# CONFIG_MTD_CFI is not set
+# CONFIG_MTD_JEDECPROBE is not set
+CONFIG_MTD_MAP_BANK_WIDTH_1=y
+CONFIG_MTD_MAP_BANK_WIDTH_2=y
+CONFIG_MTD_MAP_BANK_WIDTH_4=y
+# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set
+CONFIG_MTD_CFI_I1=y
+CONFIG_MTD_CFI_I2=y
+# CONFIG_MTD_CFI_I4 is not set
+# CONFIG_MTD_CFI_I8 is not set
+# CONFIG_MTD_RAM is not set
+# CONFIG_MTD_ROM is not set
+# CONFIG_MTD_ABSENT is not set
+
+#
+# Mapping drivers for chip access
+#
+# CONFIG_MTD_COMPLEX_MAPPINGS is not set
+# CONFIG_MTD_PLATRAM is not set
+
+#
+# Self-contained MTD device drivers
+#
+CONFIG_MTD_DATAFLASH=y
+# CONFIG_MTD_DATAFLASH_WRITE_VERIFY is not set
+# CONFIG_MTD_DATAFLASH_OTP is not set
+# CONFIG_MTD_M25P80 is not set
+# CONFIG_MTD_SST25L is not set
+# CONFIG_MTD_SLRAM is not set
+# CONFIG_MTD_PHRAM is not set
+# CONFIG_MTD_MTDRAM is not set
+# CONFIG_MTD_BLOCK2MTD is not set
+
+#
+# Disk-On-Chip Device Drivers
+#
+# CONFIG_MTD_DOC2000 is not set
+# CONFIG_MTD_DOC2001 is not set
+# CONFIG_MTD_DOC2001PLUS is not set
+CONFIG_MTD_NAND_ECC=y
+# CONFIG_MTD_NAND_ECC_SMC is not set
+CONFIG_MTD_NAND=y
+# CONFIG_MTD_NAND_VERIFY_WRITE is not set
+# CONFIG_MTD_SM_COMMON is not set
+# CONFIG_MTD_NAND_MUSEUM_IDS is not set
+# CONFIG_MTD_NAND_GPIO is not set
+CONFIG_MTD_NAND_IDS=y
+# CONFIG_MTD_NAND_DISKONCHIP is not set
+CONFIG_MTD_NAND_ATMEL=y
+CONFIG_MTD_NAND_ATMEL_ECC_SOFT=y
+# CONFIG_MTD_NAND_NANDSIM is not set
+# CONFIG_MTD_NAND_PLATFORM is not set
+# CONFIG_MTD_ALAUDA is not set
+# CONFIG_MTD_ONENAND is not set
+
+#
+# LPDDR flash memory drivers
+#
+# CONFIG_MTD_LPDDR is not set
+CONFIG_MTD_UBI=y
+CONFIG_MTD_UBI_WL_THRESHOLD=4096
+CONFIG_MTD_UBI_BEB_RESERVE=1
+# CONFIG_MTD_UBI_GLUEBI is not set
+
+#
+# UBI debugging options
+#
+# CONFIG_MTD_UBI_DEBUG is not set
+# CONFIG_PARPORT is not set
+CONFIG_BLK_DEV=y
+# CONFIG_BLK_DEV_COW_COMMON is not set
+CONFIG_BLK_DEV_LOOP=y
+# CONFIG_BLK_DEV_CRYPTOLOOP is not set
+
+#
+# DRBD disabled because PROC_FS, INET or CONNECTOR not selected
+#
+# CONFIG_BLK_DEV_NBD is not set
+# CONFIG_BLK_DEV_UB is not set
+CONFIG_BLK_DEV_RAM=y
+CONFIG_BLK_DEV_RAM_COUNT=16
+CONFIG_BLK_DEV_RAM_SIZE=8192
+# CONFIG_BLK_DEV_XIP is not set
+# CONFIG_CDROM_PKTCDVD is not set
+# CONFIG_ATA_OVER_ETH is not set
+# CONFIG_MG_DISK is not set
+# CONFIG_BLK_DEV_RBD is not set
+CONFIG_MISC_DEVICES=y
+# CONFIG_AD525X_DPOT is not set
+# CONFIG_ATMEL_TCLIB is not set
+# CONFIG_ICS932S401 is not set
+# CONFIG_ATMEL_SSC is not set
+# CONFIG_ENCLOSURE_SERVICES is not set
+# CONFIG_APDS9802ALS is not set
+# CONFIG_ISL29003 is not set
+# CONFIG_ISL29020 is not set
+# CONFIG_SENSORS_TSL2550 is not set
+# CONFIG_SENSORS_BH1780 is not set
+# CONFIG_SENSORS_BH1770 is not set
+# CONFIG_SENSORS_APDS990X is not set
+# CONFIG_HMC6352 is not set
+# CONFIG_DS1682 is not set
+# CONFIG_TI_DAC7512 is not set
+# CONFIG_BMP085 is not set
+# CONFIG_C2PORT is not set
+
+#
+# EEPROM support
+#
+CONFIG_EEPROM_AT24=y
+# CONFIG_EEPROM_AT25 is not set
+# CONFIG_EEPROM_LEGACY is not set
+# CONFIG_EEPROM_MAX6875 is not set
+CONFIG_EEPROM_93CX6=m
+# CONFIG_IWMC3200TOP is not set
+
+#
+# Texas Instruments shared transport line discipline
+#
+CONFIG_HAVE_IDE=y
+# CONFIG_IDE is not set
+
+#
+# SCSI device support
+#
+CONFIG_SCSI_MOD=y
+# CONFIG_RAID_ATTRS is not set
+CONFIG_SCSI=y
+CONFIG_SCSI_DMA=y
+# CONFIG_SCSI_TGT is not set
+# CONFIG_SCSI_NETLINK is not set
+CONFIG_SCSI_PROC_FS=y
+
+#
+# SCSI support type (disk, tape, CD-ROM)
+#
+CONFIG_BLK_DEV_SD=y
+# CONFIG_CHR_DEV_ST is not set
+# CONFIG_CHR_DEV_OSST is not set
+# CONFIG_BLK_DEV_SR is not set
+# CONFIG_CHR_DEV_SG is not set
+# CONFIG_CHR_DEV_SCH is not set
+CONFIG_SCSI_MULTI_LUN=y
+# CONFIG_SCSI_CONSTANTS is not set
+# CONFIG_SCSI_LOGGING is not set
+# CONFIG_SCSI_SCAN_ASYNC is not set
+CONFIG_SCSI_WAIT_SCAN=m
+
+#
+# SCSI Transports
+#
+# CONFIG_SCSI_SPI_ATTRS is not set
+# CONFIG_SCSI_FC_ATTRS is not set
+# CONFIG_SCSI_ISCSI_ATTRS is not set
+# CONFIG_SCSI_SAS_ATTRS is not set
+# CONFIG_SCSI_SAS_LIBSAS is not set
+# CONFIG_SCSI_SRP_ATTRS is not set
+# CONFIG_SCSI_LOWLEVEL is not set
+# CONFIG_SCSI_DH is not set
+# CONFIG_SCSI_OSD_INITIATOR is not set
+CONFIG_ATA=y
+# CONFIG_ATA_NONSTANDARD is not set
+CONFIG_ATA_VERBOSE_ERROR=y
+# CONFIG_SATA_PMP is not set
+
+#
+# Controllers with non-SFF native interface
+#
+# CONFIG_SATA_AHCI_PLATFORM is not set
+CONFIG_ATA_SFF=y
+
+#
+# SFF controllers with custom DMA interface
+#
+# CONFIG_ATA_BMDMA is not set
+
+#
+# PIO-only SFF controllers
+#
+CONFIG_PATA_AT91=y
+
+#
+# Generic fallback / legacy drivers
+#
+# CONFIG_MD is not set
+CONFIG_HAVE_NET_MACB=y
+CONFIG_NETDEVICES=y
+# CONFIG_DUMMY is not set
+# CONFIG_BONDING is not set
+# CONFIG_MACVLAN is not set
+# CONFIG_EQUALIZER is not set
+# CONFIG_TUN is not set
+# CONFIG_VETH is not set
+# CONFIG_MII is not set
+CONFIG_PHYLIB=y
+
+#
+# MII PHY device drivers
+#
+# CONFIG_MARVELL_PHY is not set
+# CONFIG_DAVICOM_PHY is not set
+# CONFIG_QSEMI_PHY is not set
+# CONFIG_LXT_PHY is not set
+# CONFIG_CICADA_PHY is not set
+# CONFIG_VITESSE_PHY is not set
+# CONFIG_SMSC_PHY is not set
+# CONFIG_BROADCOM_PHY is not set
+# CONFIG_BCM63XX_PHY is not set
+# CONFIG_ICPLUS_PHY is not set
+# CONFIG_REALTEK_PHY is not set
+# CONFIG_NATIONAL_PHY is not set
+# CONFIG_STE10XP is not set
+# CONFIG_LSI_ET1011C_PHY is not set
+# CONFIG_MICREL_PHY is not set
+# CONFIG_FIXED_PHY is not set
+# CONFIG_MDIO_BITBANG is not set
+CONFIG_NET_ETHERNET=y
+CONFIG_MACB=y
+# CONFIG_AX88796 is not set
+# CONFIG_SMC91X is not set
+# CONFIG_DM9000 is not set
+# CONFIG_ENC28J60 is not set
+# CONFIG_ETHOC is not set
+# CONFIG_SMC911X is not set
+# CONFIG_SMSC911X is not set
+# CONFIG_DNET is not set
+# CONFIG_IBM_NEW_EMAC_ZMII is not set
+# CONFIG_IBM_NEW_EMAC_RGMII is not set
+# CONFIG_IBM_NEW_EMAC_TAH is not set
+# CONFIG_IBM_NEW_EMAC_EMAC4 is not set
+# CONFIG_IBM_NEW_EMAC_NO_FLOW_CTRL is not set
+# CONFIG_IBM_NEW_EMAC_MAL_CLR_ICINTSTAT is not set
+# CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set
+# CONFIG_B44 is not set
+# CONFIG_KS8851 is not set
+# CONFIG_KS8851_MLL is not set
+# CONFIG_NETDEV_1000 is not set
+# CONFIG_NETDEV_10000 is not set
+CONFIG_WLAN=y
+# CONFIG_LIBERTAS_THINFIRM is not set
+# CONFIG_AT76C50X_USB is not set
+# CONFIG_USB_ZD1201 is not set
+# CONFIG_USB_NET_RNDIS_WLAN is not set
+CONFIG_RTL8187=m
+CONFIG_RTL8187_LEDS=y
+# CONFIG_MAC80211_HWSIM is not set
+# CONFIG_ATH_COMMON is not set
+# CONFIG_B43 is not set
+# CONFIG_B43LEGACY is not set
+# CONFIG_HOSTAP is not set
+# CONFIG_IWM is not set
+# CONFIG_LIBERTAS is not set
+# CONFIG_P54_COMMON is not set
+CONFIG_RT2X00=y
+CONFIG_RT2500USB=y
+CONFIG_RT73USB=y
+CONFIG_RT2800USB=y
+# CONFIG_RT2800USB_RT30XX is not set
+# CONFIG_RT2800USB_RT35XX is not set
+# CONFIG_RT2800USB_UNKNOWN is not set
+CONFIG_RT2800_LIB=y
+CONFIG_RT2X00_LIB_USB=y
+CONFIG_RT2X00_LIB=y
+CONFIG_RT2X00_LIB_HT=y
+CONFIG_RT2X00_LIB_FIRMWARE=y
+CONFIG_RT2X00_LIB_CRYPTO=y
+CONFIG_RT2X00_LIB_LEDS=y
+# CONFIG_RT2X00_DEBUG is not set
+# CONFIG_WL1251 is not set
+# CONFIG_WL12XX is not set
+# CONFIG_ZD1211RW is not set
+
+#
+# Enable WiMAX (Networking options) to see the WiMAX drivers
+#
+
+#
+# USB Network Adapters
+#
+# CONFIG_USB_CATC is not set
+# CONFIG_USB_KAWETH is not set
+# CONFIG_USB_PEGASUS is not set
+# CONFIG_USB_RTL8150 is not set
+# CONFIG_USB_USBNET is not set
+# CONFIG_USB_IPHETH is not set
+# CONFIG_WAN is not set
+
+#
+# CAIF transport drivers
+#
+CONFIG_PPP=y
+# CONFIG_PPP_MULTILINK is not set
+# CONFIG_PPP_FILTER is not set
+CONFIG_PPP_ASYNC=y
+# CONFIG_PPP_SYNC_TTY is not set
+CONFIG_PPP_DEFLATE=y
+CONFIG_PPP_BSDCOMP=y
+CONFIG_PPP_MPPE=y
+# CONFIG_PPPOE is not set
+# CONFIG_SLIP is not set
+CONFIG_SLHC=y
+# CONFIG_NETCONSOLE is not set
+# CONFIG_NETPOLL is not set
+# CONFIG_NET_POLL_CONTROLLER is not set
+# CONFIG_ISDN is not set
+# CONFIG_PHONE is not set
+
+#
+# Input device support
+#
+CONFIG_INPUT=y
+# CONFIG_INPUT_FF_MEMLESS is not set
+# CONFIG_INPUT_POLLDEV is not set
+# CONFIG_INPUT_SPARSEKMAP is not set
+
+#
+# Userland interfaces
+#
+CONFIG_INPUT_MOUSEDEV=y
+# CONFIG_INPUT_MOUSEDEV_PSAUX is not set
+CONFIG_INPUT_MOUSEDEV_SCREEN_X=320
+CONFIG_INPUT_MOUSEDEV_SCREEN_Y=240
+# CONFIG_INPUT_JOYDEV is not set
+CONFIG_INPUT_EVDEV=y
+# CONFIG_INPUT_EVBUG is not set
+
+#
+# Input Device Drivers
+#
+CONFIG_INPUT_KEYBOARD=y
+# CONFIG_KEYBOARD_ADP5588 is not set
+# CONFIG_KEYBOARD_ATKBD is not set
+# CONFIG_KEYBOARD_QT2160 is not set
+# CONFIG_KEYBOARD_LKKBD is not set
+CONFIG_KEYBOARD_GPIO=y
+# CONFIG_KEYBOARD_TCA6416 is not set
+# CONFIG_KEYBOARD_MATRIX is not set
+# CONFIG_KEYBOARD_LM8323 is not set
+# CONFIG_KEYBOARD_MAX7359 is not set
+# CONFIG_KEYBOARD_MCS is not set
+# CONFIG_KEYBOARD_NEWTON is not set
+# CONFIG_KEYBOARD_OPENCORES is not set
+# CONFIG_KEYBOARD_STOWAWAY is not set
+# CONFIG_KEYBOARD_SUNKBD is not set
+# CONFIG_KEYBOARD_XTKBD is not set
+# CONFIG_INPUT_MOUSE is not set
+# CONFIG_INPUT_JOYSTICK is not set
+# CONFIG_INPUT_TABLET is not set
+# CONFIG_INPUT_TOUCHSCREEN is not set
+# CONFIG_INPUT_MISC is not set
+
+#
+# Hardware I/O ports
+#
+# CONFIG_SERIO is not set
+# CONFIG_GAMEPORT is not set
+
+#
+# Character devices
+#
+CONFIG_VT=y
+CONFIG_CONSOLE_TRANSLATIONS=y
+CONFIG_VT_CONSOLE=y
+CONFIG_HW_CONSOLE=y
+# CONFIG_VT_HW_CONSOLE_BINDING is not set
+# CONFIG_DEVKMEM is not set
+# CONFIG_SERIAL_NONSTANDARD is not set
+# CONFIG_N_GSM is not set
+
+#
+# Serial drivers
+#
+# CONFIG_SERIAL_8250 is not set
+
+#
+# Non-8250 serial port support
+#
+CONFIG_SERIAL_ATMEL=y
+CONFIG_SERIAL_ATMEL_CONSOLE=y
+# CONFIG_SERIAL_ATMEL_PDC is not set
+# CONFIG_SERIAL_ATMEL_TTYAT is not set
+# CONFIG_SERIAL_MAX3100 is not set
+# CONFIG_SERIAL_MAX3107 is not set
+CONFIG_SERIAL_CORE=y
+CONFIG_SERIAL_CORE_CONSOLE=y
+# CONFIG_SERIAL_TIMBERDALE is not set
+# CONFIG_SERIAL_ALTERA_JTAGUART is not set
+# CONFIG_SERIAL_ALTERA_UART is not set
+CONFIG_UNIX98_PTYS=y
+# CONFIG_DEVPTS_MULTIPLE_INSTANCES is not set
+# CONFIG_LEGACY_PTYS is not set
+# CONFIG_IPMI_HANDLER is not set
+# CONFIG_HW_RANDOM is not set
+# CONFIG_R3964 is not set
+# CONFIG_RAW_DRIVER is not set
+# CONFIG_TCG_TPM is not set
+# CONFIG_RAMOOPS is not set
+CONFIG_I2C=y
+CONFIG_I2C_BOARDINFO=y
+# CONFIG_I2C_COMPAT is not set
+CONFIG_I2C_CHARDEV=y
+# CONFIG_I2C_MUX is not set
+CONFIG_I2C_HELPER_AUTO=y
+CONFIG_I2C_ALGOBIT=y
+# CONFIG_I2C_ALGOPCF is not set
+# CONFIG_I2C_ALGOPCA is not set
+
+#
+# I2C Hardware Bus support
+#
+
+#
+# I2C system bus drivers (mostly embedded / system-on-chip)
+#
+# CONFIG_I2C_DESIGNWARE is not set
+CONFIG_I2C_GPIO=y
+# CONFIG_I2C_OCORES is not set
+# CONFIG_I2C_PCA_PLATFORM is not set
+# CONFIG_I2C_SIMTEC is not set
+# CONFIG_I2C_XILINX is not set
+
+#
+# External I2C/SMBus adapter drivers
+#
+# CONFIG_I2C_PARPORT_LIGHT is not set
+# CONFIG_I2C_TAOS_EVM is not set
+# CONFIG_I2C_TINY_USB is not set
+
+#
+# Other I2C/SMBus bus drivers
+#
+# CONFIG_I2C_STUB is not set
+# CONFIG_I2C_DEBUG_CORE is not set
+# CONFIG_I2C_DEBUG_ALGO is not set
+# CONFIG_I2C_DEBUG_BUS is not set
+CONFIG_SPI=y
+CONFIG_SPI_MASTER=y
+
+#
+# SPI Master Controller Drivers
+#
+CONFIG_SPI_ATMEL=y
+# CONFIG_SPI_BITBANG is not set
+# CONFIG_SPI_GPIO is not set
+# CONFIG_SPI_XILINX is not set
+# CONFIG_SPI_DESIGNWARE is not set
+
+#
+# SPI Protocol Masters
+#
+CONFIG_SPI_SPIDEV=y
+# CONFIG_SPI_TLE62X0 is not set
+
+#
+# PPS support
+#
+# CONFIG_PPS is not set
+CONFIG_ARCH_REQUIRE_GPIOLIB=y
+CONFIG_GPIOLIB=y
+CONFIG_GPIO_SYSFS=y
+
+#
+# Memory mapped GPIO expanders:
+#
+# CONFIG_GPIO_BASIC_MMIO is not set
+# CONFIG_GPIO_IT8761E is not set
+# CONFIG_GPIO_VX855 is not set
+
+#
+# I2C GPIO expanders:
+#
+# CONFIG_GPIO_MAX7300 is not set
+# CONFIG_GPIO_MAX732X is not set
+# CONFIG_GPIO_PCA953X is not set
+CONFIG_GPIO_PCF857X=y
+# CONFIG_GPIO_SX150X is not set
+# CONFIG_GPIO_ADP5588 is not set
+
+#
+# PCI GPIO expanders:
+#
+
+#
+# SPI GPIO expanders:
+#
+# CONFIG_GPIO_MAX7301 is not set
+# CONFIG_GPIO_MCP23S08 is not set
+# CONFIG_GPIO_MC33880 is not set
+# CONFIG_GPIO_74X164 is not set
+
+#
+# AC97 GPIO expanders:
+#
+
+#
+# MODULbus GPIO expanders:
+#
+CONFIG_W1=y
+
+#
+# 1-wire Bus Masters
+#
+# CONFIG_W1_MASTER_DS2490 is not set
+# CONFIG_W1_MASTER_DS2482 is not set
+# CONFIG_W1_MASTER_DS1WM is not set
+CONFIG_W1_MASTER_GPIO=y
+
+#
+# 1-wire Slaves
+#
+# CONFIG_W1_SLAVE_THERM is not set
+# CONFIG_W1_SLAVE_SMEM is not set
+CONFIG_W1_SLAVE_DS2431=y
+# CONFIG_W1_SLAVE_DS2433 is not set
+# CONFIG_W1_SLAVE_DS2760 is not set
+# CONFIG_W1_SLAVE_BQ27000 is not set
+# CONFIG_POWER_SUPPLY is not set
+# CONFIG_HWMON is not set
+# CONFIG_THERMAL is not set
+# CONFIG_WATCHDOG is not set
+CONFIG_SSB_POSSIBLE=y
+
+#
+# Sonics Silicon Backplane
+#
+# CONFIG_SSB is not set
+# CONFIG_MFD_SUPPORT is not set
+# CONFIG_REGULATOR is not set
+# CONFIG_MEDIA_SUPPORT is not set
+
+#
+# Graphics support
+#
+# CONFIG_DRM is not set
+# CONFIG_VGASTATE is not set
+# CONFIG_VIDEO_OUTPUT_CONTROL is not set
+# CONFIG_FB is not set
+# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
+
+#
+# Display device support
+#
+# CONFIG_DISPLAY_SUPPORT is not set
+
+#
+# Console display driver support
+#
+CONFIG_DUMMY_CONSOLE=y
+# CONFIG_SOUND is not set
+# CONFIG_HID_SUPPORT is not set
+CONFIG_USB_SUPPORT=y
+CONFIG_USB_ARCH_HAS_HCD=y
+CONFIG_USB_ARCH_HAS_OHCI=y
+# CONFIG_USB_ARCH_HAS_EHCI is not set
+CONFIG_USB=y
+# CONFIG_USB_DEBUG is not set
+# CONFIG_USB_ANNOUNCE_NEW_DEVICES is not set
+
+#
+# Miscellaneous USB options
+#
+CONFIG_USB_DEVICEFS=y
+# CONFIG_USB_DEVICE_CLASS is not set
+# CONFIG_USB_DYNAMIC_MINORS is not set
+# CONFIG_USB_MON is not set
+# CONFIG_USB_WUSB is not set
+# CONFIG_USB_WUSB_CBAF is not set
+
+#
+# USB Host Controller Drivers
+#
+# CONFIG_USB_C67X00_HCD is not set
+# CONFIG_USB_OXU210HP_HCD is not set
+# CONFIG_USB_ISP116X_HCD is not set
+# CONFIG_USB_ISP1760_HCD is not set
+# CONFIG_USB_ISP1362_HCD is not set
+CONFIG_USB_OHCI_HCD=y
+# CONFIG_USB_OHCI_BIG_ENDIAN_DESC is not set
+# CONFIG_USB_OHCI_BIG_ENDIAN_MMIO is not set
+CONFIG_USB_OHCI_LITTLE_ENDIAN=y
+# CONFIG_USB_SL811_HCD is not set
+# CONFIG_USB_R8A66597_HCD is not set
+# CONFIG_USB_HWA_HCD is not set
+# CONFIG_USB_MUSB_HDRC is not set
+
+#
+# USB Device Class drivers
+#
+CONFIG_USB_ACM=y
+# CONFIG_USB_PRINTER is not set
+# CONFIG_USB_WDM is not set
+# CONFIG_USB_TMC is not set
+
+#
+# NOTE: USB_STORAGE depends on SCSI but BLK_DEV_SD may
+#
+
+#
+# also be needed; see USB_STORAGE Help for more info
+#
+CONFIG_USB_STORAGE=y
+# CONFIG_USB_STORAGE_DEBUG is not set
+# CONFIG_USB_STORAGE_DATAFAB is not set
+# CONFIG_USB_STORAGE_FREECOM is not set
+# CONFIG_USB_STORAGE_ISD200 is not set
+# CONFIG_USB_STORAGE_USBAT is not set
+# CONFIG_USB_STORAGE_SDDR09 is not set
+# CONFIG_USB_STORAGE_SDDR55 is not set
+# CONFIG_USB_STORAGE_JUMPSHOT is not set
+# CONFIG_USB_STORAGE_ALAUDA is not set
+# CONFIG_USB_STORAGE_ONETOUCH is not set
+# CONFIG_USB_STORAGE_KARMA is not set
+# CONFIG_USB_STORAGE_CYPRESS_ATACB is not set
+# CONFIG_USB_UAS is not set
+# CONFIG_USB_LIBUSUAL is not set
+
+#
+# USB Imaging devices
+#
+# CONFIG_USB_MDC800 is not set
+# CONFIG_USB_MICROTEK is not set
+
+#
+# USB port drivers
+#
+# CONFIG_USB_SERIAL is not set
+
+#
+# USB Miscellaneous drivers
+#
+# CONFIG_USB_EMI62 is not set
+# CONFIG_USB_EMI26 is not set
+# CONFIG_USB_ADUTUX is not set
+# CONFIG_USB_SEVSEG is not set
+# CONFIG_USB_RIO500 is not set
+# CONFIG_USB_LEGOTOWER is not set
+# CONFIG_USB_LCD is not set
+# CONFIG_USB_LED is not set
+# CONFIG_USB_CYPRESS_CY7C63 is not set
+# CONFIG_USB_CYTHERM is not set
+# CONFIG_USB_IDMOUSE is not set
+# CONFIG_USB_FTDI_ELAN is not set
+# CONFIG_USB_APPLEDISPLAY is not set
+# CONFIG_USB_LD is not set
+# CONFIG_USB_TRANCEVIBRATOR is not set
+# CONFIG_USB_IOWARRIOR is not set
+# CONFIG_USB_TEST is not set
+# CONFIG_USB_ISIGHTFW is not set
+# CONFIG_USB_YUREX is not set
+CONFIG_USB_GADGET=y
+# CONFIG_USB_GADGET_DEBUG_FILES is not set
+CONFIG_USB_GADGET_VBUS_DRAW=2
+CONFIG_USB_GADGET_SELECTED=y
+CONFIG_USB_GADGET_AT91=y
+CONFIG_USB_AT91=y
+# CONFIG_USB_GADGET_R8A66597 is not set
+# CONFIG_USB_GADGET_M66592 is not set
+# CONFIG_USB_GADGET_DUMMY_HCD is not set
+# CONFIG_USB_GADGET_DUALSPEED is not set
+# CONFIG_USB_ZERO is not set
+CONFIG_USB_ETH=y
+CONFIG_USB_ETH_RNDIS=y
+# CONFIG_USB_ETH_EEM is not set
+# CONFIG_USB_GADGETFS is not set
+# CONFIG_USB_FUNCTIONFS is not set
+# CONFIG_USB_FILE_STORAGE is not set
+# CONFIG_USB_MASS_STORAGE is not set
+# CONFIG_USB_G_SERIAL is not set
+# CONFIG_USB_G_PRINTER is not set
+# CONFIG_USB_CDC_COMPOSITE is not set
+# CONFIG_USB_G_MULTI is not set
+# CONFIG_USB_G_HID is not set
+# CONFIG_USB_G_DBGP is not set
+
+#
+# OTG and related infrastructure
+#
+# CONFIG_USB_GPIO_VBUS is not set
+# CONFIG_USB_ULPI is not set
+# CONFIG_NOP_USB_XCEIV is not set
+CONFIG_MMC=y
+# CONFIG_MMC_DEBUG is not set
+# CONFIG_MMC_UNSAFE_RESUME is not set
+
+#
+# MMC/SD/SDIO Card Drivers
+#
+CONFIG_MMC_BLOCK=y
+CONFIG_MMC_BLOCK_MINORS=8
+CONFIG_MMC_BLOCK_BOUNCE=y
+# CONFIG_SDIO_UART is not set
+# CONFIG_MMC_TEST is not set
+
+#
+# MMC/SD/SDIO Host Controller Drivers
+#
+# CONFIG_MMC_SDHCI is not set
+# CONFIG_MMC_AT91 is not set
+CONFIG_MMC_ATMELMCI=y
+# CONFIG_MMC_SPI is not set
+# CONFIG_MMC_USHC is not set
+# CONFIG_MEMSTICK is not set
+CONFIG_NEW_LEDS=y
+CONFIG_LEDS_CLASS=y
+
+#
+# LED drivers
+#
+# CONFIG_LEDS_PCA9532 is not set
+CONFIG_LEDS_GPIO=y
+CONFIG_LEDS_GPIO_PLATFORM=y
+# CONFIG_LEDS_LP3944 is not set
+# CONFIG_LEDS_LP5521 is not set
+# CONFIG_LEDS_LP5523 is not set
+# CONFIG_LEDS_PCA955X is not set
+# CONFIG_LEDS_DAC124S085 is not set
+# CONFIG_LEDS_BD2802 is not set
+# CONFIG_LEDS_LT3593 is not set
+CONFIG_LEDS_TRIGGERS=y
+
+#
+# LED Triggers
+#
+CONFIG_LEDS_TRIGGER_TIMER=y
+CONFIG_LEDS_TRIGGER_HEARTBEAT=y
+# CONFIG_LEDS_TRIGGER_BACKLIGHT is not set
+# CONFIG_LEDS_TRIGGER_GPIO is not set
+CONFIG_LEDS_TRIGGER_DEFAULT_ON=y
+
+#
+# iptables trigger is under Netfilter config (LED target)
+#
+# CONFIG_ACCESSIBILITY is not set
+CONFIG_RTC_LIB=y
+CONFIG_RTC_CLASS=y
+CONFIG_RTC_HCTOSYS=y
+CONFIG_RTC_HCTOSYS_DEVICE="rtc0"
+# CONFIG_RTC_DEBUG is not set
+
+#
+# RTC interfaces
+#
+CONFIG_RTC_INTF_SYSFS=y
+CONFIG_RTC_INTF_PROC=y
+CONFIG_RTC_INTF_DEV=y
+# CONFIG_RTC_INTF_DEV_UIE_EMUL is not set
+# CONFIG_RTC_DRV_TEST is not set
+
+#
+# I2C RTC drivers
+#
+# CONFIG_RTC_DRV_DS1307 is not set
+# CONFIG_RTC_DRV_DS1374 is not set
+# CONFIG_RTC_DRV_DS1672 is not set
+# CONFIG_RTC_DRV_DS3232 is not set
+# CONFIG_RTC_DRV_MAX6900 is not set
+# CONFIG_RTC_DRV_RS5C372 is not set
+# CONFIG_RTC_DRV_ISL1208 is not set
+# CONFIG_RTC_DRV_ISL12022 is not set
+# CONFIG_RTC_DRV_X1205 is not set
+# CONFIG_RTC_DRV_PCF8563 is not set
+# CONFIG_RTC_DRV_PCF8583 is not set
+# CONFIG_RTC_DRV_M41T80 is not set
+# CONFIG_RTC_DRV_BQ32K is not set
+# CONFIG_RTC_DRV_S35390A is not set
+# CONFIG_RTC_DRV_FM3130 is not set
+# CONFIG_RTC_DRV_RX8581 is not set
+# CONFIG_RTC_DRV_RX8025 is not set
+
+#
+# SPI RTC drivers
+#
+# CONFIG_RTC_DRV_M41T94 is not set
+# CONFIG_RTC_DRV_DS1305 is not set
+# CONFIG_RTC_DRV_DS1390 is not set
+# CONFIG_RTC_DRV_MAX6902 is not set
+# CONFIG_RTC_DRV_R9701 is not set
+# CONFIG_RTC_DRV_RS5C348 is not set
+# CONFIG_RTC_DRV_DS3234 is not set
+# CONFIG_RTC_DRV_PCF2123 is not set
+
+#
+# Platform RTC drivers
+#
+# CONFIG_RTC_DRV_CMOS is not set
+# CONFIG_RTC_DRV_DS1286 is not set
+# CONFIG_RTC_DRV_DS1511 is not set
+# CONFIG_RTC_DRV_DS1553 is not set
+# CONFIG_RTC_DRV_DS1742 is not set
+# CONFIG_RTC_DRV_STK17TA8 is not set
+# CONFIG_RTC_DRV_M48T86 is not set
+# CONFIG_RTC_DRV_M48T35 is not set
+# CONFIG_RTC_DRV_M48T59 is not set
+# CONFIG_RTC_DRV_MSM6242 is not set
+# CONFIG_RTC_DRV_BQ4802 is not set
+# CONFIG_RTC_DRV_RP5C01 is not set
+# CONFIG_RTC_DRV_V3020 is not set
+
+#
+# on-CPU RTC drivers
+#
+CONFIG_RTC_DRV_AT91SAM9=y
+CONFIG_RTC_DRV_AT91SAM9_RTT=0
+CONFIG_RTC_DRV_AT91SAM9_GPBR=0
+# CONFIG_DMADEVICES is not set
+# CONFIG_AUXDISPLAY is not set
+# CONFIG_UIO is not set
+# CONFIG_STAGING is not set
+
+#
+# File systems
+#
+CONFIG_EXT2_FS=y
+# CONFIG_EXT2_FS_XATTR is not set
+# CONFIG_EXT2_FS_XIP is not set
+CONFIG_EXT3_FS=y
+CONFIG_EXT3_DEFAULTS_TO_ORDERED=y
+# CONFIG_EXT3_FS_XATTR is not set
+CONFIG_EXT4_FS=y
+# CONFIG_EXT4_FS_XATTR is not set
+# CONFIG_EXT4_DEBUG is not set
+CONFIG_JBD=y
+CONFIG_JBD2=y
+# CONFIG_REISERFS_FS is not set
+# CONFIG_JFS_FS is not set
+# CONFIG_FS_POSIX_ACL is not set
+# CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
+# CONFIG_OCFS2_FS is not set
+# CONFIG_BTRFS_FS is not set
+# CONFIG_NILFS2_FS is not set
+CONFIG_FILE_LOCKING=y
+CONFIG_FSNOTIFY=y
+CONFIG_DNOTIFY=y
+CONFIG_INOTIFY_USER=y
+# CONFIG_FANOTIFY is not set
+# CONFIG_QUOTA is not set
+# CONFIG_QUOTACTL is not set
+# CONFIG_AUTOFS4_FS is not set
+# CONFIG_FUSE_FS is not set
+
+#
+# Caches
+#
+# CONFIG_FSCACHE is not set
+
+#
+# CD-ROM/DVD Filesystems
+#
+# CONFIG_ISO9660_FS is not set
+# CONFIG_UDF_FS is not set
+
+#
+# DOS/FAT/NT Filesystems
+#
+CONFIG_FAT_FS=y
+# CONFIG_MSDOS_FS is not set
+CONFIG_VFAT_FS=y
+CONFIG_FAT_DEFAULT_CODEPAGE=437
+CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1"
+# CONFIG_NTFS_FS is not set
+
+#
+# Pseudo filesystems
+#
+CONFIG_PROC_FS=y
+CONFIG_PROC_SYSCTL=y
+CONFIG_PROC_PAGE_MONITOR=y
+CONFIG_SYSFS=y
+CONFIG_TMPFS=y
+# CONFIG_TMPFS_POSIX_ACL is not set
+# CONFIG_HUGETLB_PAGE is not set
+# CONFIG_CONFIGFS_FS is not set
+CONFIG_MISC_FILESYSTEMS=y
+# CONFIG_ADFS_FS is not set
+# CONFIG_AFFS_FS is not set
+# CONFIG_HFS_FS is not set
+# CONFIG_HFSPLUS_FS is not set
+# CONFIG_BEFS_FS is not set
+# CONFIG_BFS_FS is not set
+# CONFIG_EFS_FS is not set
+CONFIG_JFFS2_FS=y
+CONFIG_JFFS2_FS_DEBUG=0
+CONFIG_JFFS2_FS_WRITEBUFFER=y
+# CONFIG_JFFS2_FS_WBUF_VERIFY is not set
+CONFIG_JFFS2_SUMMARY=y
+# CONFIG_JFFS2_FS_XATTR is not set
+# CONFIG_JFFS2_COMPRESSION_OPTIONS is not set
+CONFIG_JFFS2_ZLIB=y
+# CONFIG_JFFS2_LZO is not set
+CONFIG_JFFS2_RTIME=y
+# CONFIG_JFFS2_RUBIN is not set
+CONFIG_UBIFS_FS=y
+# CONFIG_UBIFS_FS_XATTR is not set
+# CONFIG_UBIFS_FS_ADVANCED_COMPR is not set
+CONFIG_UBIFS_FS_LZO=y
+CONFIG_UBIFS_FS_ZLIB=y
+# CONFIG_UBIFS_FS_DEBUG is not set
+# CONFIG_LOGFS is not set
+# CONFIG_CRAMFS is not set
+# CONFIG_SQUASHFS is not set
+# CONFIG_VXFS_FS is not set
+# CONFIG_MINIX_FS is not set
+# CONFIG_OMFS_FS is not set
+# CONFIG_HPFS_FS is not set
+# CONFIG_QNX4FS_FS is not set
+# CONFIG_ROMFS_FS is not set
+# CONFIG_SYSV_FS is not set
+# CONFIG_UFS_FS is not set
+CONFIG_NETWORK_FILESYSTEMS=y
+CONFIG_NFS_FS=y
+CONFIG_NFS_V3=y
+# CONFIG_NFS_V3_ACL is not set
+# CONFIG_NFS_V4 is not set
+# CONFIG_NFSD is not set
+CONFIG_LOCKD=y
+CONFIG_LOCKD_V4=y
+CONFIG_NFS_COMMON=y
+CONFIG_SUNRPC=y
+# CONFIG_RPCSEC_GSS_KRB5 is not set
+# CONFIG_CEPH_FS is not set
+# CONFIG_CIFS is not set
+# CONFIG_NCP_FS is not set
+# CONFIG_CODA_FS is not set
+# CONFIG_AFS_FS is not set
+
+#
+# Partition Types
+#
+# CONFIG_PARTITION_ADVANCED is not set
+CONFIG_MSDOS_PARTITION=y
+CONFIG_NLS=y
+CONFIG_NLS_DEFAULT="iso8859-1"
+CONFIG_NLS_CODEPAGE_437=y
+# CONFIG_NLS_CODEPAGE_737 is not set
+# CONFIG_NLS_CODEPAGE_775 is not set
+CONFIG_NLS_CODEPAGE_850=y
+# CONFIG_NLS_CODEPAGE_852 is not set
+# CONFIG_NLS_CODEPAGE_855 is not set
+# CONFIG_NLS_CODEPAGE_857 is not set
+# CONFIG_NLS_CODEPAGE_860 is not set
+# CONFIG_NLS_CODEPAGE_861 is not set
+# CONFIG_NLS_CODEPAGE_862 is not set
+# CONFIG_NLS_CODEPAGE_863 is not set
+# CONFIG_NLS_CODEPAGE_864 is not set
+# CONFIG_NLS_CODEPAGE_865 is not set
+# CONFIG_NLS_CODEPAGE_866 is not set
+# CONFIG_NLS_CODEPAGE_869 is not set
+# CONFIG_NLS_CODEPAGE_936 is not set
+# CONFIG_NLS_CODEPAGE_950 is not set
+# CONFIG_NLS_CODEPAGE_932 is not set
+# CONFIG_NLS_CODEPAGE_949 is not set
+# CONFIG_NLS_CODEPAGE_874 is not set
+# CONFIG_NLS_ISO8859_8 is not set
+# CONFIG_NLS_CODEPAGE_1250 is not set
+# CONFIG_NLS_CODEPAGE_1251 is not set
+# CONFIG_NLS_ASCII is not set
+CONFIG_NLS_ISO8859_1=y
+# CONFIG_NLS_ISO8859_2 is not set
+# CONFIG_NLS_ISO8859_3 is not set
+# CONFIG_NLS_ISO8859_4 is not set
+# CONFIG_NLS_ISO8859_5 is not set
+# CONFIG_NLS_ISO8859_6 is not set
+# CONFIG_NLS_ISO8859_7 is not set
+# CONFIG_NLS_ISO8859_9 is not set
+# CONFIG_NLS_ISO8859_13 is not set
+# CONFIG_NLS_ISO8859_14 is not set
+CONFIG_NLS_ISO8859_15=y
+# CONFIG_NLS_KOI8_R is not set
+# CONFIG_NLS_KOI8_U is not set
+CONFIG_NLS_UTF8=y
+# CONFIG_DLM is not set
+
+#
+# Kernel hacking
+#
+# CONFIG_PRINTK_TIME is not set
+CONFIG_ENABLE_WARN_DEPRECATED=y
+CONFIG_ENABLE_MUST_CHECK=y
+CONFIG_FRAME_WARN=1024
+# CONFIG_MAGIC_SYSRQ is not set
+# CONFIG_STRIP_ASM_SYMS is not set
+# CONFIG_UNUSED_SYMBOLS is not set
+# CONFIG_DEBUG_FS is not set
+# CONFIG_HEADERS_CHECK is not set
+# CONFIG_DEBUG_KERNEL is not set
+# CONFIG_HARDLOCKUP_DETECTOR is not set
+CONFIG_BKL=y
+# CONFIG_SPARSE_RCU_POINTER is not set
+CONFIG_DEBUG_BUGVERBOSE=y
+CONFIG_DEBUG_MEMORY_INIT=y
+CONFIG_FRAME_POINTER=y
+# CONFIG_RCU_CPU_STALL_DETECTOR is not set
+# CONFIG_SYSCTL_SYSCALL_CHECK is not set
+CONFIG_HAVE_FUNCTION_TRACER=y
+CONFIG_HAVE_DYNAMIC_FTRACE=y
+CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
+CONFIG_TRACING_SUPPORT=y
+# CONFIG_FTRACE is not set
+# CONFIG_ATOMIC64_SELFTEST is not set
+# CONFIG_SAMPLES is not set
+CONFIG_HAVE_ARCH_KGDB=y
+# CONFIG_STRICT_DEVMEM is not set
+# CONFIG_ARM_UNWIND is not set
+# CONFIG_DEBUG_USER is not set
+# CONFIG_OC_ETM is not set
+
+#
+# Security options
+#
+# CONFIG_KEYS is not set
+# CONFIG_SECURITY_DMESG_RESTRICT is not set
+# CONFIG_SECURITY is not set
+# CONFIG_SECURITYFS is not set
+CONFIG_DEFAULT_SECURITY_DAC=y
+CONFIG_DEFAULT_SECURITY=""
+CONFIG_CRYPTO=y
+
+#
+# Crypto core or helper
+#
+CONFIG_CRYPTO_ALGAPI=y
+CONFIG_CRYPTO_ALGAPI2=y
+CONFIG_CRYPTO_AEAD2=y
+CONFIG_CRYPTO_BLKCIPHER=y
+CONFIG_CRYPTO_BLKCIPHER2=y
+CONFIG_CRYPTO_HASH=y
+CONFIG_CRYPTO_HASH2=y
+CONFIG_CRYPTO_RNG=m
+CONFIG_CRYPTO_RNG2=y
+CONFIG_CRYPTO_PCOMP2=y
+CONFIG_CRYPTO_MANAGER=y
+CONFIG_CRYPTO_MANAGER2=y
+CONFIG_CRYPTO_MANAGER_DISABLE_TESTS=y
+# CONFIG_CRYPTO_GF128MUL is not set
+# CONFIG_CRYPTO_NULL is not set
+CONFIG_CRYPTO_WORKQUEUE=y
+# CONFIG_CRYPTO_CRYPTD is not set
+# CONFIG_CRYPTO_AUTHENC is not set
+# CONFIG_CRYPTO_TEST is not set
+
+#
+# Authenticated Encryption with Associated Data
+#
+# CONFIG_CRYPTO_CCM is not set
+# CONFIG_CRYPTO_GCM is not set
+# CONFIG_CRYPTO_SEQIV is not set
+
+#
+# Block modes
+#
+# CONFIG_CRYPTO_CBC is not set
+# CONFIG_CRYPTO_CTR is not set
+# CONFIG_CRYPTO_CTS is not set
+CONFIG_CRYPTO_ECB=y
+# CONFIG_CRYPTO_LRW is not set
+# CONFIG_CRYPTO_PCBC is not set
+# CONFIG_CRYPTO_XTS is not set
+
+#
+# Hash modes
+#
+# CONFIG_CRYPTO_HMAC is not set
+# CONFIG_CRYPTO_XCBC is not set
+# CONFIG_CRYPTO_VMAC is not set
+
+#
+# Digest
+#
+CONFIG_CRYPTO_CRC32C=m
+# CONFIG_CRYPTO_GHASH is not set
+# CONFIG_CRYPTO_MD4 is not set
+# CONFIG_CRYPTO_MD5 is not set
+# CONFIG_CRYPTO_MICHAEL_MIC is not set
+# CONFIG_CRYPTO_RMD128 is not set
+# CONFIG_CRYPTO_RMD160 is not set
+# CONFIG_CRYPTO_RMD256 is not set
+# CONFIG_CRYPTO_RMD320 is not set
+CONFIG_CRYPTO_SHA1=y
+# CONFIG_CRYPTO_SHA256 is not set
+# CONFIG_CRYPTO_SHA512 is not set
+# CONFIG_CRYPTO_TGR192 is not set
+# CONFIG_CRYPTO_WP512 is not set
+
+#
+# Ciphers
+#
+CONFIG_CRYPTO_AES=y
+# CONFIG_CRYPTO_ANUBIS is not set
+CONFIG_CRYPTO_ARC4=y
+# CONFIG_CRYPTO_BLOWFISH is not set
+# CONFIG_CRYPTO_CAMELLIA is not set
+# CONFIG_CRYPTO_CAST5 is not set
+# CONFIG_CRYPTO_CAST6 is not set
+# CONFIG_CRYPTO_DES is not set
+# CONFIG_CRYPTO_FCRYPT is not set
+# CONFIG_CRYPTO_KHAZAD is not set
+# CONFIG_CRYPTO_SALSA20 is not set
+# CONFIG_CRYPTO_SEED is not set
+# CONFIG_CRYPTO_SERPENT is not set
+# CONFIG_CRYPTO_TEA is not set
+# CONFIG_CRYPTO_TWOFISH is not set
+
+#
+# Compression
+#
+CONFIG_CRYPTO_DEFLATE=y
+# CONFIG_CRYPTO_ZLIB is not set
+CONFIG_CRYPTO_LZO=y
+
+#
+# Random Number Generation
+#
+CONFIG_CRYPTO_ANSI_CPRNG=m
+CONFIG_CRYPTO_HW=y
+# CONFIG_BINARY_PRINTF is not set
+
+#
+# Library routines
+#
+CONFIG_BITREVERSE=y
+CONFIG_GENERIC_FIND_LAST_BIT=y
+CONFIG_CRC_CCITT=y
+CONFIG_CRC16=y
+# CONFIG_CRC_T10DIF is not set
+CONFIG_CRC_ITU_T=y
+CONFIG_CRC32=y
+# CONFIG_CRC7 is not set
+CONFIG_LIBCRC32C=m
+CONFIG_ZLIB_INFLATE=y
+CONFIG_ZLIB_DEFLATE=y
+CONFIG_LZO_COMPRESS=y
+CONFIG_LZO_DECOMPRESS=y
+CONFIG_DECOMPRESS_GZIP=y
+CONFIG_DECOMPRESS_BZIP2=y
+CONFIG_DECOMPRESS_LZMA=y
+CONFIG_DECOMPRESS_LZO=y
+CONFIG_HAS_IOMEM=y
+CONFIG_HAS_IOPORT=y
+CONFIG_HAS_DMA=y
+CONFIG_NLATTR=y
+CONFIG_GENERIC_ATOMIC64=y
diff --git a/arch/arm/mach-at91/Kconfig b/arch/arm/mach-at91/Kconfig
index c015b68..5f31223 100644
--- a/arch/arm/mach-at91/Kconfig
+++ b/arch/arm/mach-at91/Kconfig
@@ -381,6 +381,13 @@ config MACH_PCONTROL_G20
Select this if you are using taskit's Stamp9G20 CPU module on this
carrier board, beeing the decentralized unit of a building automation
system; featuring nvram, eth-switch, iso-rs485, display, io
+
+config MACH_STAMP9G20GMS
+ bool "GeoSIG Stamp9G20 GMS"
+ help
+ Select this if you are using taskit's Stamp9G20 with GeoSIG's GMS.
+ <http://www.geosig.com>
+
endif
if (ARCH_AT91SAM9260 || ARCH_AT91SAM9G20)
diff --git a/arch/arm/mach-at91/Makefile b/arch/arm/mach-at91/Makefile
index 62d686f..6eeeba7 100644
--- a/arch/arm/mach-at91/Makefile
+++ b/arch/arm/mach-at91/Makefile
@@ -64,6 +64,7 @@ obj-$(CONFIG_MACH_AT91SAM9RLEK) += board-sam9rlek.o
obj-$(CONFIG_MACH_AT91SAM9G20EK) += board-sam9g20ek.o
obj-$(CONFIG_MACH_CPU9G20) += board-cpu9krea.o
obj-$(CONFIG_MACH_STAMP9G20) += board-stamp9g20.o
+obj-$(CONFIG_MACH_STAMP9G20GMS) += board-stamp9g20gms.o
obj-$(CONFIG_MACH_PORTUXG20) += board-stamp9g20.o
obj-$(CONFIG_MACH_PCONTROL_G20) += board-pcontrol-g20.o
diff --git a/arch/arm/mach-at91/board-stamp9g20gms.c b/arch/arm/mach-at91/board-stamp9g20gms.c
new file mode 100644
index 0000000..d286c1f
--- /dev/null
+++ b/arch/arm/mach-at91/board-stamp9g20gms.c
@@ -0,0 +1,720 @@
+/*
+ * Copyright (C) 2010 Christian Glindkamp <christian.glindkamp at taskit.de>
+ * taskit GmbH
+ * 2010 Igor Plyatov <plyatov at gmail.com>
+ * GeoSIG Ltd
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ */
+
+#include <linux/mm.h>
+#include <linux/platform_device.h>
+#include <linux/gpio.h>
+#include <linux/w1-gpio.h>
+#include <linux/i2c/pcf857x.h>
+#include <linux/gpio_keys.h>
+#include <linux/input.h>
+
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+
+#include <mach/board.h>
+#include <mach/at91sam9_smc.h>
+#include <mach/gms.h>
+
+#include "sam9_smc.h"
+#include "generic.h"
+
+static void __init stamp9g20gms_map_io(void)
+{
+ /* Initialize processor: 18.432 MHz crystal */
+ at91sam9260_initialize(18432000);
+
+ /* DGBU on ttyS0. (Rx & Tx only) */
+ at91_register_uart(0, 0, 0);
+
+ /*
+ * USART0 on ttyS1 (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI).
+ * Used for Internal Analog Modem.
+ */
+ at91_register_uart(AT91SAM9260_ID_US0, 1,
+ ATMEL_UART_CTS | ATMEL_UART_RTS
+ | ATMEL_UART_DTR | ATMEL_UART_DSR
+ | ATMEL_UART_DCD | ATMEL_UART_RI);
+ /*
+ * USART1 on ttyS2 (Rx, Tx, CTS, RTS).
+ * Used for GPS or WiFi or Data stream.
+ */
+ at91_register_uart(AT91SAM9260_ID_US1, 2,
+ ATMEL_UART_CTS | ATMEL_UART_RTS);
+ /*
+ * USART2 on ttyS3 (Rx, Tx, CTS, RTS).
+ * Used for External Modem.
+ */
+ at91_register_uart(AT91SAM9260_ID_US2, 3,
+ ATMEL_UART_CTS | ATMEL_UART_RTS);
+ /*
+ * USART3 on ttyS4 (Rx, Tx, RTS).
+ * Used for RS-485.
+ */
+ at91_register_uart(AT91SAM9260_ID_US3, 4, ATMEL_UART_RTS);
+ /*
+ * USART4 on ttyS5 (Rx, Tx).
+ * Used for TRX433 Radio Module.
+ */
+ at91_register_uart(AT91SAM9260_ID_US4, 5, 0);
+
+ /* set serial console to ttyS0 (ie, DBGU) */
+ at91_set_serial_console(0);
+}
+
+static void __init init_irq(void)
+{
+ at91sam9260_init_interrupts(NULL);
+}
+
+/******************************************************************************
+ * NAND flash
+ ******************************************************************************/
+static struct atmel_nand_data __initdata nand_data = {
+ .ale = 21,
+ .cle = 22,
+ .rdy_pin = AT91_PIN_PC13,
+ .enable_pin = AT91_PIN_PC14,
+ .bus_width_16 = 0,
+};
+
+static struct sam9_smc_config __initdata nand_smc_config = {
+ .ncs_read_setup = 0,
+ .nrd_setup = 2,
+ .ncs_write_setup = 0,
+ .nwe_setup = 2,
+
+ .ncs_read_pulse = 4,
+ .nrd_pulse = 4,
+ .ncs_write_pulse = 4,
+ .nwe_pulse = 4,
+
+ .read_cycle = 7,
+ .write_cycle = 7,
+
+ .mode = AT91_SMC_READMODE | \
+ AT91_SMC_WRITEMODE | \
+ AT91_SMC_EXNWMODE_DISABLE | \
+ AT91_SMC_DBW_8,
+ .tdf_cycles = 3,
+};
+
+static void __init add_device_nand(void)
+{
+ /* configure chip-select 3 (NAND) */
+ sam9_smc_configure(3, &nand_smc_config);
+
+ at91_add_device_nand(&nand_data);
+}
+
+/******************************************************************************
+ * MCI (SD/MMC)
+ * det_pin, wp_pin and vcc_pin are not connected
+ ******************************************************************************/
+#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE)
+static struct mci_platform_data __initdata mmc_data = {
+ .slot[0] = {
+ .bus_width = 4,
+ },
+};
+#else
+static struct at91_mmc_data __initdata mmc_data = {
+ .slot_b = 0,
+ .wire4 = 1,
+};
+#endif
+
+/******************************************************************************
+ * USB Host port
+ ******************************************************************************/
+static struct at91_usbh_data __initdata usbh_data = {
+ .ports = 2,
+};
+
+
+/******************************************************************************
+ * USB Device port
+ ******************************************************************************/
+static struct at91_udc_data __initdata stamp9g20gms_udc_data = {
+ .vbus_pin = AT91_PIN_PA22,
+ .pullup_pin = 0, /* pull-up driven by UDC */
+};
+
+
+/******************************************************************************
+ * MACB Ethernet device
+ ******************************************************************************/
+static struct at91_eth_data __initdata macb_data = {
+ .phy_irq_pin = AT91_PIN_PA28,
+ .is_rmii = 1,
+};
+
+
+/******************************************************************************
+ * LEDs and GPOs
+ ******************************************************************************/
+#if defined(CONFIG_LEDS_GPIO) || defined(CONFIG_LEDS_GPIO_MODULE)
+static struct gpio_led stamp9g20gms_gpio_leds[] = {
+ {
+ .name = "gpo:spi1reset",
+ .gpio = AT91_PIN_PC1,
+ .active_low = 0,
+ .default_trigger = "none",
+ .default_state = LEDS_GPIO_DEFSTATE_OFF,
+ },
+ {
+ .name = "gpo:trig_net_out",
+ .gpio = AT91_PIN_PB20,
+ .active_low = 0,
+ .default_trigger = "none",
+ .default_state = LEDS_GPIO_DEFSTATE_OFF,
+ },
+ {
+ .name = "gpo:trig_net_dir",
+ .gpio = AT91_PIN_PB19,
+ .active_low = 0,
+ .default_trigger = "none",
+ .default_state = LEDS_GPIO_DEFSTATE_OFF,
+ },
+ {
+ .name = "gpo:charge_dis",
+ .gpio = AT91_PIN_PC2,
+ .active_low = 0,
+ .default_trigger = "none",
+ .default_state = LEDS_GPIO_DEFSTATE_OFF,
+ },
+ {
+ .name = "led:event",
+ .gpio = AT91_PIN_PB17,
+ .active_low = 1,
+ .default_trigger = "none",
+ .default_state = LEDS_GPIO_DEFSTATE_OFF,
+ },
+ {
+ .name = "led:lan",
+ .gpio = AT91_PIN_PB18,
+ .active_low = 1,
+ .default_trigger = "none",
+ .default_state = LEDS_GPIO_DEFSTATE_OFF,
+ },
+ {
+ .name = "led:error",
+ .gpio = AT91_PIN_PB16,
+ .active_low = 1,
+ .default_trigger = "none",
+ .default_state = LEDS_GPIO_DEFSTATE_ON,
+ }
+};
+
+static struct gpio_led_platform_data stamp9g20gms_gpio_led_info = {
+ .leds = stamp9g20gms_gpio_leds,
+ .num_leds = ARRAY_SIZE(stamp9g20gms_gpio_leds),
+};
+
+static struct platform_device stamp9g20gms_leds = {
+ .name = "leds-gpio",
+ .id = 0,
+ .dev = {
+ .platform_data = &stamp9g20gms_gpio_led_info,
+ }
+};
+
+static void __init stamp9g20gms_leds_init(void)
+{
+ platform_device_register(&stamp9g20gms_leds);
+}
+#else
+static inline void stamp9g20gms_leds_init(void) {}
+#endif
+
+/* PCF8574 0x20 GPIO - U1 on the GS_IA18-CB_V3 board */
+#if (defined(CONFIG_LEDS_GPIO) || defined(CONFIG_LEDS_GPIO_MODULE)) && \
+ (defined(CONFIG_GPIO_PCF857X) || defined(CONFIG_GPIO_PCF857X_MODULE))
+static struct gpio_led stamp9g20gms_pcf_gpio_leds1[] = {
+ { /* bit 0 */
+ .name = "gpo:hdc_power",
+ .gpio = PCF_GPIO_HDC_POWER,
+ .active_low = 0,
+ .default_trigger = "none",
+ .default_state = LEDS_GPIO_DEFSTATE_OFF,
+ },
+ { /* bit 1 */
+ .name = "gpo:wifi_setup",
+ .gpio = PCF_GPIO_WIFI_SETUP,
+ .active_low = 1,
+ .default_trigger = "none",
+ .default_state = LEDS_GPIO_DEFSTATE_OFF,
+ },
+ { /* bit 2 */
+ .name = "gpo:wifi_enable",
+ .gpio = PCF_GPIO_WIFI_ENABLE,
+ .active_low = 1,
+ .default_trigger = "none",
+ .default_state = LEDS_GPIO_DEFSTATE_OFF,
+ },
+ { /* bit 3 */
+ .name = "gpo:wifi_reset",
+ .gpio = PCF_GPIO_WIFI_RESET,
+ .active_low = 1,
+ .default_trigger = "none",
+ .default_state = LEDS_GPIO_DEFSTATE_ON,
+ },
+ /* bit 4 used as GPI */
+ { /* bit 5 */
+ .name = "gpo:gps_setup",
+ .gpio = PCF_GPIO_GPS_SETUP,
+ .active_low = 1,
+ .default_trigger = "none",
+ .default_state = LEDS_GPIO_DEFSTATE_OFF,
+ },
+ { /* bit 6 */
+ .name = "gpo:gps_standby",
+ .gpio = PCF_GPIO_GPS_STANDBY,
+ .active_low = 0,
+ .default_trigger = "none",
+ .default_state = LEDS_GPIO_DEFSTATE_ON,
+ },
+ { /* bit 7 */
+ .name = "gpo:gps_power",
+ .gpio = PCF_GPIO_GPS_POWER,
+ .active_low = 0,
+ .default_trigger = "none",
+ .default_state = LEDS_GPIO_DEFSTATE_OFF,
+ }
+};
+
+static struct gpio_led_platform_data stamp9g20gms_pcf_gpio_led_info1 = {
+ .leds = stamp9g20gms_pcf_gpio_leds1,
+ .num_leds = ARRAY_SIZE(stamp9g20gms_pcf_gpio_leds1),
+};
+
+static struct platform_device stamp9g20gms_pcf_leds1 = {
+ .name = "leds-gpio", /* GS_IA18-CB_board */
+ .id = 1,
+ .dev = {
+ .platform_data = &stamp9g20gms_pcf_gpio_led_info1,
+ }
+};
+
+/* PCF8574 0x22 GPIO - U1 on the GS_2G_OPT1-A_V0 board (Alarm) */
+static struct gpio_led stamp9g20gms_pcf_gpio_leds2[] = {
+ { /* bit 0 */
+ .name = "gpo:alarm_1",
+ .gpio = PCF_GPIO_ALARM1,
+ .active_low = 1,
+ .default_trigger = "none",
+ .default_state = LEDS_GPIO_DEFSTATE_OFF,
+ },
+ { /* bit 1 */
+ .name = "gpo:alarm_2",
+ .gpio = PCF_GPIO_ALARM2,
+ .active_low = 1,
+ .default_trigger = "none",
+ .default_state = LEDS_GPIO_DEFSTATE_OFF,
+ },
+ { /* bit 2 */
+ .name = "gpo:alarm_3",
+ .gpio = PCF_GPIO_ALARM3,
+ .active_low = 1,
+ .default_trigger = "none",
+ .default_state = LEDS_GPIO_DEFSTATE_OFF,
+ },
+ { /* bit 3 */
+ .name = "gpo:alarm_4",
+ .gpio = PCF_GPIO_ALARM4,
+ .active_low = 1,
+ .default_trigger = "none",
+ .default_state = LEDS_GPIO_DEFSTATE_OFF,
+ },
+ /* bits 4, 5, 6 not used */
+ { /* bit 7 */
+ .name = "gpo:alarm_v_relay_on",
+ .gpio = PCF_GPIO_ALARM_V_RELAY_ON,
+ .active_low = 0,
+ .default_trigger = "none",
+ .default_state = LEDS_GPIO_DEFSTATE_OFF,
+ },
+};
+
+static struct gpio_led_platform_data stamp9g20gms_pcf_gpio_led_info2 = {
+ .leds = stamp9g20gms_pcf_gpio_leds2,
+ .num_leds = ARRAY_SIZE(stamp9g20gms_pcf_gpio_leds2),
+};
+
+static struct platform_device stamp9g20gms_pcf_leds2 = {
+ .name = "leds-gpio",
+ .id = 2,
+ .dev = {
+ .platform_data = &stamp9g20gms_pcf_gpio_led_info2,
+ }
+};
+
+/* PCF8574 0x24 GPIO U1 on the GS_2G-OPT23-A_V0 board (Modem) */
+static struct gpio_led stamp9g20gms_pcf_gpio_leds3[] = {
+ { /* bit 0 */
+ .name = "gpo:modem_power",
+ .gpio = PCF_GPIO_MODEM_POWER,
+ .active_low = 1,
+ .default_trigger = "none",
+ .default_state = LEDS_GPIO_DEFSTATE_OFF,
+ },
+ /* bits 1 and 2 not used */
+ { /* bit 3 */
+ .name = "gpo:modem_reset",
+ .gpio = PCF_GPIO_MODEM_RESET,
+ .active_low = 1,
+ .default_trigger = "none",
+ .default_state = LEDS_GPIO_DEFSTATE_ON,
+ },
+ /* bits 4, 5 and 6 not used */
+ { /* bit 7 */
+ .name = "gpo:trx_reset",
+ .gpio = PCF_GPIO_TRX_RESET,
+ .active_low = 1,
+ .default_trigger = "none",
+ .default_state = LEDS_GPIO_DEFSTATE_ON,
+ }
+};
+
+static struct gpio_led_platform_data stamp9g20gms_pcf_gpio_led_info3 = {
+ .leds = stamp9g20gms_pcf_gpio_leds3,
+ .num_leds = ARRAY_SIZE(stamp9g20gms_pcf_gpio_leds3),
+};
+
+static struct platform_device stamp9g20gms_pcf_leds3 = {
+ .name = "leds-gpio",
+ .id = 3,
+ .dev = {
+ .platform_data = &stamp9g20gms_pcf_gpio_led_info3,
+ }
+};
+
+static void __init stamp9g20gms_pcf_leds_init(void)
+{
+ platform_device_register(&stamp9g20gms_pcf_leds1);
+ platform_device_register(&stamp9g20gms_pcf_leds2);
+ platform_device_register(&stamp9g20gms_pcf_leds3);
+}
+#else
+static inline void stamp9g20gms_pcf_leds_init(void) {}
+#endif /* CONFIG_LEDS_GPIO || CONFIG_GPIO_PCF857X */
+
+/******************************************************************************
+ * SPI busses.
+ ******************************************************************************/
+static struct spi_board_info stamp9g20gms_spi_devices[] = {
+ { /* User accessible spi0, cs0 used for communication with MSP RTC */
+ .modalias = "spidev",
+ .bus_num = 0,
+ .chip_select = 0,
+ .max_speed_hz = 580000,
+ .mode = SPI_MODE_1,
+ },
+ { /* User accessible spi1, cs0 used for communication with int. DSP */
+ .modalias = "spidev",
+ .bus_num = 1,
+ .chip_select = 0,
+ .max_speed_hz = 5600000,
+ .mode = SPI_MODE_0,
+ },
+ { /* User accessible spi1, cs1 used for communication with ext. DSP */
+ .modalias = "spidev",
+ .bus_num = 1,
+ .chip_select = 1,
+ .max_speed_hz = 5600000,
+ .mode = SPI_MODE_0,
+ },
+ { /* User accessible spi1, cs2 used for communication with ext. DSP */
+ .modalias = "spidev",
+ .bus_num = 1,
+ .chip_select = 2,
+ .max_speed_hz = 5600000,
+ .mode = SPI_MODE_0,
+ },
+ { /* User accessible spi1, cs3 used for communication with ext. DSP */
+ .modalias = "spidev",
+ .bus_num = 1,
+ .chip_select = 3,
+ .max_speed_hz = 5600000,
+ .mode = SPI_MODE_0,
+ }
+};
+
+/******************************************************************************
+ * Dallas 1-Wire
+ ******************************************************************************/
+static struct w1_gpio_platform_data w1_gpio_pdata = {
+ .pin = AT91_PIN_PA29,
+ .is_open_drain = 1,
+};
+
+static struct platform_device w1_device = {
+ .name = "w1-gpio",
+ .id = -1,
+ .dev.platform_data = &w1_gpio_pdata,
+};
+
+void add_w1(void)
+{
+ at91_set_GPIO_periph(w1_gpio_pdata.pin, 1);
+ at91_set_multi_drive(w1_gpio_pdata.pin, 1);
+ platform_device_register(&w1_device);
+}
+
+/******************************************************************************
+ * GPI Buttons
+ ******************************************************************************/
+#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
+static struct gpio_keys_button stamp9g20gms_buttons[] = {
+ {
+ .gpio = AT91_PIN_PB21,
+ .code = BTN_1,
+ .desc = "TRIG_NET_IN",
+ .type = EV_KEY,
+ .active_low = 0,
+ .wakeup = 1,
+ },
+ {
+ .gpio = AT91_PIN_PB13, /* SW80 */
+ .code = BTN_2,
+ .desc = "Card umount 0",
+ .type = EV_KEY,
+ .active_low = 1,
+ .wakeup = 1,
+ },
+ {
+ .gpio = AT91_PIN_PB12, /* SW79 */
+ .code = BTN_3,
+ .desc = "Card umount 1",
+ .type = EV_KEY,
+ .active_low = 1,
+ .wakeup = 1,
+ },
+ {
+ .gpio = AT91_PIN_PA25,
+ .code = KEY_POWER,
+ .desc = "Power Off Button",
+ .type = EV_KEY,
+ .active_low = 0,
+ .wakeup = 1,
+ }
+};
+
+static struct gpio_keys_platform_data stamp9g20gms_button_data = {
+ .buttons = stamp9g20gms_buttons,
+ .nbuttons = ARRAY_SIZE(stamp9g20gms_buttons),
+};
+
+static struct platform_device stamp9g20gms_button_device = {
+ .name = "gpio-keys",
+ .id = -1,
+ .num_resources = 0,
+ .dev = {
+ .platform_data = &stamp9g20gms_button_data,
+ }
+};
+
+static void __init stamp9g20gms_add_device_buttons(void)
+{
+ /* Configure "TRIG_NET_IN" input with pullup */
+ at91_set_gpio_input(AT91_PIN_PB21, 1); /* BTN_1 */
+ at91_set_deglitch(AT91_PIN_PB21, 1);
+ /* Configure "Card umount 0" input with pullup */
+ at91_set_gpio_input(AT91_PIN_PB12, 1); /* BTN_2 */
+ at91_set_deglitch(AT91_PIN_PB12, 1);
+ /* Configure "Card umount 1" input with pullup */
+ at91_set_gpio_input(AT91_PIN_PB13, 1); /* BTN_3 */
+ at91_set_deglitch(AT91_PIN_PB13, 1);
+ /* Configure "Power Off Button" input without pullup */
+ at91_set_gpio_input(AT91_PIN_PA25, 0); /* KEY_POWER */
+ at91_set_deglitch(AT91_PIN_PA25, 1);
+
+ platform_device_register(&stamp9g20gms_button_device);
+}
+#else
+static void __init stamp9g20gms_add_device_buttons(void) {}
+#endif
+
+/******************************************************************************
+ * I2C
+ ******************************************************************************/
+#if defined(CONFIG_GPIO_PCF857X) || defined(CONFIG_GPIO_PCF857X_MODULE)
+static int pcf8574x_0x20_setup(struct i2c_client *client, int gpio,
+ unsigned int ngpio, void *context)
+{
+ int status;
+
+ status = gpio_request(gpio + 4, "eth_det");
+ if (status < 0) {
+ pr_err("error: can't request GPIO%d\n", gpio + 4);
+ return -ENOSYS;
+ }
+ status = gpio_direction_input(gpio + 4);
+ if (status < 0) {
+ pr_err("error: can't setup GPIO%d as input\n", gpio + 4);
+ return -ENOSYS;
+ }
+ status = gpio_export(gpio + 4, false);
+ if (status < 0) {
+ pr_err("error: can't export GPIO%d\n", gpio + 4);
+ return -ENOSYS;
+ }
+ status = gpio_sysfs_set_active_low(gpio + 4, 1);
+ if (status < 0) {
+ pr_err("error: gpio_sysfs_set active_low(GPIO%d, 1)\n", gpio+4);
+ return -ENOSYS;
+ }
+
+ return 0;
+}
+
+static int pcf8574x_0x20_teardown(struct i2c_client *client, int gpio,
+ unsigned ngpio, void *context)
+{
+ gpio_free(gpio + 4);
+ return 0;
+}
+
+static struct pcf857x_platform_data stamp9g20_pcf20_pdata = {
+ .gpio_base = GS_IA18_S_PCF_GPIO_BASE0,
+ .n_latch = (1 << 4),
+ .setup = pcf8574x_0x20_setup,
+ .teardown = pcf8574x_0x20_teardown,
+};
+
+static struct pcf857x_platform_data stamp9g20_pcf22_pdata = {
+ .gpio_base = GS_IA18_S_PCF_GPIO_BASE1,
+};
+
+static struct pcf857x_platform_data stamp9g20_pcf24_pdata = {
+ .gpio_base = GS_IA18_S_PCF_GPIO_BASE2,
+};
+#endif /* CONFIG_GPIO_PCF857X */
+
+static struct i2c_board_info __initdata stamp9g20gms_i2c_devices[] = {
+#if defined(CONFIG_GPIO_PCF857X) || defined(CONFIG_GPIO_PCF857X_MODULE)
+ { /* U1 on the GS_IA18-CB_V3 board */
+ I2C_BOARD_INFO("pcf8574", 0x20),
+ .platform_data = &stamp9g20_pcf20_pdata,
+ },
+ { /* U1 on the GS_2G_OPT1-A_V0 board (Alarm) */
+ I2C_BOARD_INFO("pcf8574", 0x22),
+ .platform_data = &stamp9g20_pcf22_pdata,
+ },
+ { /* U1 on the GS_2G-OPT23-A_V0 board (Modem) */
+ I2C_BOARD_INFO("pcf8574", 0x24),
+ .platform_data = &stamp9g20_pcf24_pdata,
+ },
+#endif /* CONFIG_GPIO_PCF857X */
+#if defined(CONFIG_EEPROM_AT24) || defined(CONFIG_EEPROM_AT24_MODULE)
+ {
+ I2C_BOARD_INFO("24c1024", 0x50),
+ },
+#else
+ {
+ NULL,
+ },
+#endif /* CONFIG_EEPROM_AT24 */
+};
+
+/******************************************************************************
+ * Compact Flash
+ ******************************************************************************/
+#if defined(CONFIG_PATA_AT91) || defined(CONFIG_PATA_AT91_MODULE)
+static struct at91_cf_data __initdata stamp9g20gms_cf1_data = {
+ .irq_pin = AT91_PIN_PA27,
+ .det_pin = AT91_PIN_PB30,
+ .rst_pin = AT91_PIN_PB31,
+ .chipselect = 5,
+ .flags = AT91_CF_TRUE_IDE,
+};
+#endif /* CONFIG_PATA_AT91 */
+
+/* Power Off by RTC */
+static void stamp9g20gms_power_off(void)
+{
+ pr_notice("Power supply will be switched off automatically now or after"
+ " 60 seconds without ArmDAS.\n");
+ at91_set_gpio_output(AT91_PIN_PA25, 1);
+ /* Spin to death... */
+ while (1)
+ ;
+}
+
+static int __init stamp9g20gms_power_off_init(void)
+{
+ pm_power_off = stamp9g20gms_power_off;
+ return 0;
+}
+
+/* ---------------------------------------------------------------------------*/
+
+static void __init generic_board_init(void)
+{
+ /* Serial */
+ at91_add_device_serial();
+ /* NAND */
+ add_device_nand();
+ /* MMC */
+#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE)
+ at91_add_device_mci(0, &mmc_data);
+#else
+ at91_add_device_mmc(0, &mmc_data);
+#endif /* CONFIG_MMC_ATMELMCI */
+ /* W1 */
+ add_w1();
+}
+
+static void __init stamp9g20gms_board_init(void)
+{
+ generic_board_init();
+ /* USB Host */
+ at91_add_device_usbh(&usbh_data);
+ /* USB Device */
+ at91_add_device_udc(&stamp9g20gms_udc_data);
+ /* Ethernet */
+ at91_add_device_eth(&macb_data);
+ /* LEDs */
+ stamp9g20gms_leds_init();
+ stamp9g20gms_pcf_leds_init();
+ /* Push Buttons */
+ stamp9g20gms_add_device_buttons();
+ /* I2C */
+ at91_add_device_i2c(stamp9g20gms_i2c_devices,
+ ARRAY_SIZE(stamp9g20gms_i2c_devices));
+ /* Compact Flash */
+#if defined(CONFIG_PATA_AT91) || defined(CONFIG_PATA_AT91_MODULE)
+ at91_add_device_cf(&stamp9g20gms_cf1_data);
+#endif /* CONFIG_PATA_AT91 */
+ /* SPI */
+ at91_add_device_spi(stamp9g20gms_spi_devices,
+ ARRAY_SIZE(stamp9g20gms_spi_devices));
+ stamp9g20gms_power_off_init();
+}
+
+MACHINE_START(STAMP9G20, "Stamp9G20 on the GeoSIG GS_IA18_S board")
+ /* Maintainer: GeoSIG Ltd */
+ .boot_params = AT91_SDRAM_BASE + 0x100,
+ .timer = &at91sam926x_timer,
+ .map_io = stamp9g20gms_map_io,
+ .init_irq = init_irq,
+ .init_machine = stamp9g20gms_board_init,
+MACHINE_END
diff --git a/arch/arm/mach-at91/include/mach/gms.h b/arch/arm/mach-at91/include/mach/gms.h
new file mode 100644
index 0000000..5d5b46f
--- /dev/null
+++ b/arch/arm/mach-at91/include/mach/gms.h
@@ -0,0 +1,27 @@
+/* PCF8574 0x20 GPIO - U1 on the GS_IA18-CB_V3 board */
+#define GS_IA18_S_PCF_GPIO_BASE0 NR_BUILTIN_GPIO
+#define PCF_GPIO_HDC_POWER (GS_IA18_S_PCF_GPIO_BASE0 + 0)
+#define PCF_GPIO_WIFI_SETUP (GS_IA18_S_PCF_GPIO_BASE0 + 1)
+#define PCF_GPIO_WIFI_ENABLE (GS_IA18_S_PCF_GPIO_BASE0 + 2)
+#define PCF_GPIO_WIFI_RESET (GS_IA18_S_PCF_GPIO_BASE0 + 3)
+#define PCF_GPIO_ETH_DETECT (GS_IA18_S_PCF_GPIO_BASE0 + 4)
+#define PCF_GPIO_GPS_SETUP (GS_IA18_S_PCF_GPIO_BASE0 + 5)
+#define PCF_GPIO_GPS_STANDBY (GS_IA18_S_PCF_GPIO_BASE0 + 6)
+#define PCF_GPIO_GPS_POWER (GS_IA18_S_PCF_GPIO_BASE0 + 7)
+
+/* PCF8574 0x22 GPIO - U1 on the GS_2G_OPT1-A_V0 board (Alarm) */
+#define GS_IA18_S_PCF_GPIO_BASE1 (GS_IA18_S_PCF_GPIO_BASE0 + 8)
+#define PCF_GPIO_ALARM1 (GS_IA18_S_PCF_GPIO_BASE1 + 0)
+#define PCF_GPIO_ALARM2 (GS_IA18_S_PCF_GPIO_BASE1 + 1)
+#define PCF_GPIO_ALARM3 (GS_IA18_S_PCF_GPIO_BASE1 + 2)
+#define PCF_GPIO_ALARM4 (GS_IA18_S_PCF_GPIO_BASE1 + 3)
+/* bits 4, 5, 6 not used */
+#define PCF_GPIO_ALARM_V_RELAY_ON (GS_IA18_S_PCF_GPIO_BASE1 + 7)
+
+/* PCF8574 0x24 GPIO U1 on the GS_2G-OPT23-A_V0 board (Modem) */
+#define GS_IA18_S_PCF_GPIO_BASE2 (GS_IA18_S_PCF_GPIO_BASE1 + 8)
+#define PCF_GPIO_MODEM_POWER (GS_IA18_S_PCF_GPIO_BASE2 + 0)
+#define PCF_GPIO_MODEM_RESET (GS_IA18_S_PCF_GPIO_BASE2 + 3)
+/* bits 1, 2, 4, 5 not used */
+#define PCF_GPIO_TRX_RESET (GS_IA18_S_PCF_GPIO_BASE2 + 6)
+/* bit 7 not used */
--
1.7.0.4
More information about the linux-arm-kernel
mailing list