[PATCH 5/5] U300 I2C board setup

[Linus Walleij]

This sets up the U300 I2C subdevices so that the AB3100
analog baseband ASIC is properly detected and also the
camera devices in the U335 reference design get properly
registered.

Signed-off-by: Linus Walleij <linus.walleij at stericsson.com>
----
This is meant to be applied on top of the previous SPI board
info patch but can probably be applied cleanly by itself as
well.
---
 arch/arm/mach-u300/Makefile |    1 +
 arch/arm/mach-u300/core.c   |    8 ++++++--
 arch/arm/mach-u300/i2c.c    |   43 +++++++++++++++++++++++++++++++++++++++++++
 arch/arm/mach-u300/i2c.h    |   23 +++++++++++++++++++++++
 4 files changed, 73 insertions(+), 2 deletions(-)
 create mode 100644 arch/arm/mach-u300/i2c.c
 create mode 100644 arch/arm/mach-u300/i2c.h

diff --git a/arch/arm/mach-u300/Makefile b/arch/arm/mach-u300/Makefile
index 4941f89..885b5c0 100644
--- a/arch/arm/mach-u300/Makefile
+++ b/arch/arm/mach-u300/Makefile
@@ -11,3 +11,4 @@ obj-$(CONFIG_ARCH_U300)	          += u300.o
 obj-$(CONFIG_MMC)                 += mmc.o
 obj-$(CONFIG_SPI_PL022)           += spi.o
 obj-$(CONFIG_MACH_U300_SPIDUMMY)  += dummyspichip.o
+obj-$(CONFIG_I2C_STU300)          += i2c.o
diff --git a/arch/arm/mach-u300/core.c b/arch/arm/mach-u300/core.c
index 8019aa6..be60d6d 100644
--- a/arch/arm/mach-u300/core.c
+++ b/arch/arm/mach-u300/core.c
@@ -33,6 +33,7 @@
 #include "clock.h"
 #include "mmc.h"
 #include "spi.h"
+#include "i2c.h"
 
 /*
  * Static I/O mappings that are needed for booting the U300 platforms. The
@@ -379,14 +380,14 @@ static struct platform_device wdog_device = {
 };
 
 static struct platform_device i2c0_device = {
-	.name = "stddci2c",
+	.name = "stu300",
 	.id = 0,
 	.num_resources = ARRAY_SIZE(i2c0_resources),
 	.resource = i2c0_resources,
 };
 
 static struct platform_device i2c1_device = {
-	.name = "stddci2c",
+	.name = "stu300",
 	.id = 1,
 	.num_resources = ARRAY_SIZE(i2c1_resources),
 	.resource = i2c1_resources,
@@ -625,6 +626,9 @@ void __init u300_init_devices(void)
 
 	u300_assign_physmem();
 
+	/* Register subdevices on the I2C buses */
+	u300_i2c_register_board_devices();
+
 	/* Register subdevices on the SPI bus */
 	u300_spi_register_board_devices();
 
diff --git a/arch/arm/mach-u300/i2c.c b/arch/arm/mach-u300/i2c.c
new file mode 100644
index 0000000..10be1f8
--- /dev/null
+++ b/arch/arm/mach-u300/i2c.c
@@ -0,0 +1,43 @@
+/*
+ * arch/arm/mach-u300/i2c.c
+ *
+ * Copyright (C) 2009 ST-Ericsson AB
+ * License terms: GNU General Public License (GPL) version 2
+ *
+ * Register board i2c devices
+ * Author: Linus Walleij <linus.walleij at stericsson.com>
+ */
+#include <linux/kernel.h>
+#include <linux/i2c.h>
+#include <mach/irqs.h>
+
+static struct i2c_board_info __initdata bus0_i2c_board_info[] = {
+	{
+		.type = "ab3100",
+		.addr = 0x48,
+		.irq = IRQ_U300_IRQ0_EXT,
+	},
+};
+
+static struct i2c_board_info __initdata bus1_i2c_board_info[] = {
+#ifdef CONFIG_MACH_U300_BS335
+	{
+		.type = "fwcam",
+		.addr = 0x10,
+	},
+	{
+		.type = "fwcam",
+		.addr = 0x5d,
+	},
+#else
+	{ },
+#endif
+};
+
+void __init u300_i2c_register_board_devices(void)
+{
+	i2c_register_board_info(0, bus0_i2c_board_info,
+				ARRAY_SIZE(bus0_i2c_board_info));
+	i2c_register_board_info(1, bus1_i2c_board_info,
+				ARRAY_SIZE(bus1_i2c_board_info));
+}
diff --git a/arch/arm/mach-u300/i2c.h b/arch/arm/mach-u300/i2c.h
new file mode 100644
index 0000000..485c02e
--- /dev/null
+++ b/arch/arm/mach-u300/i2c.h
@@ -0,0 +1,23 @@
+/*
+ * arch/arm/mach-u300/i2c.h
+ *
+ * Copyright (C) 2009 ST-Ericsson AB
+ * License terms: GNU General Public License (GPL) version 2
+ *
+ * Register board i2c devices
+ * Author: Linus Walleij <linus.walleij at stericsson.com>
+ */
+
+#ifndef MACH_U300_I2C_H
+#define MACH_U300_I2C_H
+
+#ifdef CONFIG_I2C_STU300
+void __init u300_i2c_register_board_devices(void);
+#else
+/* Compile out this stuff if no I2C adapter is available */
+static inline void __init u300_i2c_register_board_devices(void)
+{
+}
+#endif
+
+#endif
-- 
1.6.2.1