[PATCH v2 2/2] thermal: amlogic: Add support for A9 thermal controller
Xianwei Zhao via B4 Relay
devnull+xianwei.zhao.amlogic.com at kernel.org
Tue Aug 11 01:37:44 PDT 2026
From: Xianwei Zhao <xianwei.zhao at amlogic.com>
Add support for the Amlogic A9 thermal controller.
The A9 thermal controller uses different calibration parameters, requires
separate core and bus clocks, and supports a hardware over-temperature
reset mechanism.
Add support for configuring the hardware reset temperature through the
'amlogic,hw-reset-temp' Device Tree property. Newer chips can specify the
hardware reset temperature through Device Tree, while older chips without
this property continue to use the default value of 110°C for backward
compatibility.
Also restore the hardware reset configuration after resume.
Signed-off-by: Xianwei Zhao <xianwei.zhao at amlogic.com>
---
drivers/thermal/amlogic_thermal.c | 108 ++++++++++++++++++++++++++++++++++++--
1 file changed, 105 insertions(+), 3 deletions(-)
diff --git a/drivers/thermal/amlogic_thermal.c b/drivers/thermal/amlogic_thermal.c
index a0b530624b60..96090c5e6061 100644
--- a/drivers/thermal/amlogic_thermal.c
+++ b/drivers/thermal/amlogic_thermal.c
@@ -45,6 +45,18 @@
TSENSOR_CFG_REG1_DEM_EN | \
TSENSOR_CFG_REG1_CH_SEL)
+#define TSENSOR_CFG_REG2 0x8
+ #define TSENSOR_CFG_REG2_HITEMP_EN BIT(31)
+ #define TSENSOR_CFG_REG2_REBOOT_EN BIT(30)
+ #define TSENSOR_CFG_REG2_REBOOT_CODE GENMASK(15, 4)
+ #define TSENSOR_CFG_REG2_REBOOT_TIME GENMASK(23, 16)
+ #define TSENSOR_CFG_REG2_ENABLE \
+ (TSENSOR_CFG_REG2_HITEMP_EN | \
+ TSENSOR_CFG_REG2_REBOOT_EN | \
+ TSENSOR_CFG_REG2_REBOOT_TIME)
+
+#define TSENSOR_TEMP_CAL 1
+
#define TSENSOR_STAT0 0x40
#define TSENSOR_STAT9 0x64
@@ -63,6 +75,7 @@
#define TSENSOR_CALIB_OFFSET 1
#define TSENSOR_CALIB_SHIFT 4
+#define TSENSOR_HW_RESET_DEFAULT_TEMP 110000
/**
* struct amlogic_thermal_soc_calib_data
@@ -93,6 +106,7 @@ struct amlogic_thermal_data {
const struct amlogic_thermal_soc_calib_data *calibration_parameters;
const struct regmap_config *regmap_config;
bool use_sm;
+ bool has_sysclk;
};
struct amlogic_thermal {
@@ -101,8 +115,10 @@ struct amlogic_thermal {
struct regmap *regmap;
struct regmap *sec_ao_map;
struct clk *clk;
+ struct clk *sysclk;
struct thermal_zone_device *tzd;
u32 trim_info;
+ u32 temp_code;
struct meson_sm_firmware *sm_fw;
u32 tsensor_id;
};
@@ -138,6 +154,49 @@ static int amlogic_thermal_code_to_millicelsius(struct amlogic_thermal *pdata,
return temp;
}
+/*
+ * Calculate a temperature code from a temperature value .
+ * The unit of the temperature is degree milliCelsius.
+ */
+static u32 amlogic_thermal_millicelsius_to_code(struct amlogic_thermal *pdata, int millicelsius)
+{
+ const struct amlogic_thermal_soc_calib_data *param =
+ pdata->data->calibration_parameters;
+ s64 factor, uptat, uefuse;
+ u32 temp_code;
+
+ uefuse = pdata->trim_info & TSENSOR_TRIM_SIGN_MASK ?
+ ~(pdata->trim_info & TSENSOR_TRIM_TEMP_MASK) + 1 :
+ (pdata->trim_info & TSENSOR_TRIM_TEMP_MASK);
+
+ factor = param->B + div_s64(millicelsius, 100);
+ factor = BIT(16) * factor;
+ factor = div_s64(factor, param->A);
+ factor = factor - uefuse;
+
+ uptat = param->n * factor;
+ uptat = div_s64(uptat, BIT(16));
+ uptat = param->m - uptat;
+
+ factor = factor * 100;
+ if (!uptat)
+ factor = TSENSOR_TEMP_MASK << 0x4;
+ else
+ factor = div_s64(factor, uptat);
+
+ temp_code = ((factor >> 0x4) & TSENSOR_TEMP_MASK) + TSENSOR_TEMP_CAL;
+
+ return temp_code;
+}
+
+static void amlogic_tsensor_setup_hw_reset(struct amlogic_thermal *data)
+{
+ regmap_update_bits(data->regmap, TSENSOR_CFG_REG2, TSENSOR_CFG_REG2_REBOOT_CODE,
+ data->temp_code << 0x4);
+ regmap_update_bits(data->regmap, TSENSOR_CFG_REG2,
+ TSENSOR_CFG_REG2_ENABLE, TSENSOR_CFG_REG2_ENABLE);
+}
+
static int amlogic_thermal_enable(struct amlogic_thermal *data)
{
int ret;
@@ -254,6 +313,13 @@ static const struct amlogic_thermal_soc_calib_data amlogic_thermal_g12a = {
.n = 324,
};
+static const struct amlogic_thermal_soc_calib_data amlogic_thermal_a9 = {
+ .A = 9164,
+ .B = 2747,
+ .m = 370,
+ .n = 270,
+};
+
static const struct amlogic_thermal_data amlogic_thermal_g12a_cpu_param = {
.u_efuse_off = 0x128,
.calibration_parameters = &amlogic_thermal_g12a,
@@ -272,6 +338,13 @@ static const struct amlogic_thermal_data amlogic_thermal_a1_cpu_param = {
.regmap_config = &amlogic_thermal_regmap_config_g12a,
};
+static const struct amlogic_thermal_data amlogic_thermal_a9_param = {
+ .use_sm = true,
+ .has_sysclk = true,
+ .calibration_parameters = &amlogic_thermal_a9,
+ .regmap_config = &amlogic_thermal_regmap_config_g12a,
+};
+
static const struct amlogic_thermal_data amlogic_thermal_t7_param = {
.use_sm = true,
.calibration_parameters = &amlogic_thermal_g12a,
@@ -291,6 +364,10 @@ static const struct of_device_id of_amlogic_thermal_match[] = {
.compatible = "amlogic,a1-cpu-thermal",
.data = &amlogic_thermal_a1_cpu_param,
},
+ {
+ .compatible = "amlogic,a9-thermal",
+ .data = &amlogic_thermal_a9_param,
+ },
{
.compatible = "amlogic,t7-thermal",
.data = &amlogic_thermal_t7_param,
@@ -305,6 +382,7 @@ static int amlogic_thermal_probe(struct platform_device *pdev)
struct device *dev = &pdev->dev;
void __iomem *base;
int ret;
+ u32 reset_temp;
pdata = devm_kzalloc(dev, sizeof(*pdata), GFP_KERNEL);
if (!pdata)
@@ -323,9 +401,24 @@ static int amlogic_thermal_probe(struct platform_device *pdev)
if (IS_ERR(pdata->regmap))
return PTR_ERR(pdata->regmap);
- pdata->clk = devm_clk_get(dev, NULL);
- if (IS_ERR(pdata->clk))
- return dev_err_probe(dev, PTR_ERR(pdata->clk), "failed to get clock\n");
+ if (pdata->data->has_sysclk) {
+ pdata->clk = devm_clk_get(dev, "core");
+ if (IS_ERR(pdata->clk))
+ return dev_err_probe(dev, PTR_ERR(pdata->clk), "failed to get core clk\n");
+ pdata->sysclk = devm_clk_get_enabled(dev, "pclk");
+ if (IS_ERR(pdata->sysclk))
+ return dev_err_probe(dev, PTR_ERR(pdata->sysclk), "failed to get pclk\n");
+ } else {
+ pdata->clk = devm_clk_get(dev, NULL);
+ if (IS_ERR(pdata->clk))
+ return dev_err_probe(dev, PTR_ERR(pdata->clk), "failed to get clock\n");
+ }
+
+ if (of_property_read_u32(pdev->dev.of_node, "amlogic,hw-reset-temp", &reset_temp)) {
+ dev_dbg(dev, "using default hardware reset temperature\n");
+ reset_temp = TSENSOR_HW_RESET_DEFAULT_TEMP;
+ }
+
if (pdata->data->use_sm)
ret = amlogic_thermal_probe_sm(pdev, pdata);
@@ -346,6 +439,10 @@ static int amlogic_thermal_probe(struct platform_device *pdev)
devm_thermal_add_hwmon_sysfs(&pdev->dev, pdata->tzd);
+ pdata->temp_code = amlogic_thermal_millicelsius_to_code(pdata, reset_temp);
+
+ amlogic_tsensor_setup_hw_reset(pdata);
+
ret = amlogic_thermal_enable(pdata);
return ret;
@@ -363,6 +460,8 @@ static int amlogic_thermal_suspend(struct device *dev)
struct amlogic_thermal *data = dev_get_drvdata(dev);
amlogic_thermal_disable(data);
+ if (data->data->has_sysclk)
+ clk_disable_unprepare(data->sysclk);
return 0;
}
@@ -371,6 +470,9 @@ static int amlogic_thermal_resume(struct device *dev)
{
struct amlogic_thermal *data = dev_get_drvdata(dev);
+ if (data->data->has_sysclk)
+ clk_prepare_enable(data->sysclk);
+ amlogic_tsensor_setup_hw_reset(data);
return amlogic_thermal_enable(data);
}
--
2.52.0
More information about the linux-amlogic
mailing list