[PATCH v1 03/11] arm64: dts: amlogic: Used onboard usb hub reset on odroid c2

[Neil Armstrong]

On 04/01/2023 09:13, Anand Moon wrote:
> Hi Martin,
> 
> On Wed, 28 Dec 2022 at 20:14, Anand Moon <linux.amoon at gmail.com> wrote:
>>
>> Hi Martin,
>>
>> On Wed, 28 Dec 2022 at 18:21, Martin Blumenstingl
>> <martin.blumenstingl at googlemail.com> wrote:
>>>
>>> Hi Anand,
>>>
>> Thanks for your review comments.
>>
>>> thank you for working on this topic!
>>>
>>> On Wed, Dec 28, 2022 at 11:05 AM Anand Moon <linux.amoon at gmail.com> wrote:
>>> [...]
>>>> +       usb {
>>>> +               dr_mode = "host";
>>>> +               #address-cells = <1>;
>>>> +               #size-cells = <0>;
>>>> +
>>>> +               hub at 1 {
>>>> +                       /* Genesys Logic GL852G-OHG usb hub */
>>>> +                       compatible = "genesys,usb5e3,610";
>>>> +                       reg = <1>;
>>>> +                       vdd-supply = <&usb_otg_pwr>;
>>>> +                       reset-gpio = <&gpio_ao GPIOAO_4 GPIO_ACTIVE_LOW>;
>>>> +               };
>>>> +       };
>>> My understanding is that the hub at 1 node should be part of the
>>> corresponding USB controller node, not a new node.
>>> In this case hub at 1 should go into the existing &usb1 node. That way we
>>> describe the way the hardware is set up (meaning: hub at 1 is connected
>>> to &usb1).
>>>
>>
>> Ok, I will move this code under &usb0 and &usb1 nodes.
>>
>> onboard_usb_hub module just assists in usb hub reset.
>> so these changes are meant to replace the gpio-hog.
>>
>> $ dmesg | grep onboard
>> [    5.405558] usbcore: registered new device driver onboard-usb-hub
>> [    6.383428] onboard-usb-hub 1-1: reset high-speed USB device number
>> 2 using dwc2
>>
>> Here is the boot log of the odroid c2 [0] https://pastebin.com/PFy5waPb
>>
> 
> Moving the usb hub into usb subnode usb0 or usb1 does not work
> on Odroid n2 and c4, we have a combo phys of usb 2.0 and usb 3.0
> so the onboard usb hub reset does not get initialized until both the PHY
> and USB nodes are brought up by the drivers.

Fine, then add a comment before the usb node explaining that.

Thanks,
Neil

> 
> # On Odroid n2 has a combo hub
> alarm at odroid-n2:~$ lsusb -tv
> /:  Bus 02.Port 1: Dev 1, Class=root_hub, Driver=xhci-hcd/1p, 5000M
>      ID 1d6b:0003 Linux Foundation 3.0 root hub
>      |__ Port 1: Dev 2, If 0, Class=Hub, Driver=hub/4p, 5000M
>          ID 05e3:0620 Genesys Logic, Inc. GL3523 Hub
>          |__ Port 1: Dev 5, If 0, Class=Mass Storage, Driver=usb-storage, 5000M
>              ID 174c:5106 ASMedia Technology Inc. ASM1051 SATA 3Gb/s bridge
> /:  Bus 01.Port 1: Dev 1, Class=root_hub, Driver=xhci-hcd/2p, 480M
>      ID 1d6b:0002 Linux Foundation 2.0 root hub
>      |__ Port 1: Dev 2, If 0, Class=Hub, Driver=hub/4p, 480M
>          ID 05e3:0610 Genesys Logic, Inc. Hub
>          |__ Port 2: Dev 4, If 0, Class=Vendor Specific Class,
> Driver=ax88179_178a, 480M
>              ID 0b95:1790 ASIX Electronics Corp. AX88179 Gigabit Ethernet
> 
> # Odroid C4 also has a combo hub
> 
> alarm at odroid-c4:~$ lsusb -tv
> /:  Bus 02.Port 1: Dev 1, Class=root_hub, Driver=xhci-hcd/1p, 5000M
>      ID 1d6b:0003 Linux Foundation 3.0 root hub
>      |__ Port 1: Dev 2, If 0, Class=Hub, Driver=hub/4p, 5000M
>          ID 2109:0817 VIA Labs, Inc.
> /:  Bus 01.Port 1: Dev 1, Class=root_hub, Driver=xhci-hcd/2p, 480M
>      ID 1d6b:0002 Linux Foundation 2.0 root hub
>      |__ Port 1: Dev 2, If 0, Class=Hub, Driver=hub/4p, 480M
>          ID 2109:2817 VIA Labs, Inc.
> 
> So I will continue to work with this usb hub node to do a proper reset
> of the USB hub.
> 
>>> In case hub at 1 is not detected within &usb1 then you maym need something
>>> like [0] (not tested for your use-case).
>>> If that helps: feel free to include that patch in your series.
>>>
>>
>> Thanks, will check if this is needed in this case. As of now it just
>> reinitializes the hub.
>>
>>>
>>> Best regards,
>>> Martin
>>>
>>>
>>> [0] https://github.com/xdarklight/linux/commit/d8b96e5bc9c20ab2585194e0e59580c3b062c431
>>
>> Thanks
>> -Anand
> 
> Thanks
> -Anand