[PATCH] phy: dphy: Correct clk_pre parameter
Andrzej Hajda
andrzej.hajda at intel.com
Tue Jan 18 01:24:52 PST 2022
Hi,
On 18.01.2022 03:59, Liu Ying wrote:
> The D-PHY specification (v1.2) explicitly mentions that the T-CLK-PRE
> parameter's unit is Unit Interval(UI) and the minimum value is 8. Also,
> kernel doc of the 'clk_pre' member of struct phy_configure_opts_mipi_dphy
> mentions that it should be in UI. However, the dphy core driver wrongly
> sets 'clk_pre' to 8000, which seems to hint that it's in picoseconds.
> And, the kernel doc of the 'clk_pre' member wrongly says the minimum value
> is '8 UI', instead of 8.
>
> So, let's fix both the dphy core driver and the kernel doc of the 'clk_pre'
> member to correctly reflect the T-CLK-PRE parameter's unit and the minimum
> value according to the D-PHY specification.
>
> I'm assuming that all impacted custom drivers shall program values in
> TxByteClkHS cycles into hardware for the T-CLK-PRE parameter. The D-PHY
> specification mentions that the frequency of TxByteClkHS is exactly 1/8
> the High-Speed(HS) bit rate(each HS bit consumes one UI). So, relevant
> custom driver code is changed to program those values as
> DIV_ROUND_UP(cfg->clk_pre, MIPI_DPHY_UI_PER_TXBYTECLKHS_PERIOD), then.
>
> Note that I've only tested the patch with RM67191 DSI panel on i.MX8mq EVK.
> Help is needed to test with other i.MX8mq, Meson and Rockchip platforms,
> as I don't have the hardwares.
>
> Fixes: 2ed869990e14 ("phy: Add MIPI D-PHY configuration options")
> Cc: Andrzej Hajda <andrzej.hajda at intel.com>
> Cc: Neil Armstrong <narmstrong at baylibre.com>
> Cc: Robert Foss <robert.foss at linaro.org>
> Cc: Laurent Pinchart <Laurent.pinchart at ideasonboard.com>
> Cc: Jonas Karlman <jonas at kwiboo.se>
> Cc: Jernej Skrabec <jernej.skrabec at gmail.com>
> Cc: David Airlie <airlied at linux.ie>
> Cc: Daniel Vetter <daniel at ffwll.ch>
> Cc: Kishon Vijay Abraham I <kishon at ti.com>
> Cc: Vinod Koul <vkoul at kernel.org>
> Cc: Kevin Hilman <khilman at baylibre.com>
> Cc: Jerome Brunet <jbrunet at baylibre.com>
> Cc: Martin Blumenstingl <martin.blumenstingl at googlemail.com>
> Cc: Heiko Stuebner <heiko at sntech.de>
> Cc: Maxime Ripard <mripard at kernel.org>
> Cc: Guido Günther <agx at sigxcpu.org>
> Tested-by: Liu Ying <victor.liu at nxp.com> # RM67191 DSI panel on i.MX8mq EVK
> Signed-off-by: Liu Ying <victor.liu at nxp.com>
> ---
> drivers/gpu/drm/bridge/nwl-dsi.c | 7 ++-----
> drivers/phy/amlogic/phy-meson-axg-mipi-dphy.c | 3 ++-
> drivers/phy/phy-core-mipi-dphy.c | 4 ++--
> drivers/phy/rockchip/phy-rockchip-inno-dsidphy.c | 3 ++-
> include/linux/phy/phy-mipi-dphy.h | 4 +++-
> 5 files changed, 11 insertions(+), 10 deletions(-)
>
> diff --git a/drivers/gpu/drm/bridge/nwl-dsi.c b/drivers/gpu/drm/bridge/nwl-dsi.c
> index a7389a0facfb..f1fdcdf763ee 100644
> --- a/drivers/gpu/drm/bridge/nwl-dsi.c
> +++ b/drivers/gpu/drm/bridge/nwl-dsi.c
> @@ -196,12 +196,9 @@ static u32 ps2bc(struct nwl_dsi *dsi, unsigned long long ps)
> /*
> * ui2bc - UI time periods to byte clock cycles
> */
> -static u32 ui2bc(struct nwl_dsi *dsi, unsigned long long ui)
> +static u32 ui2bc(struct nwl_dsi *dsi, unsigned int ui)
> {
> - u32 bpp = mipi_dsi_pixel_format_to_bpp(dsi->format);
> -
> - return DIV64_U64_ROUND_UP(ui * dsi->lanes,
> - dsi->mode.clock * 1000 * bpp);
> + return DIV_ROUND_UP(ui, MIPI_DPHY_UI_PER_TXBYTECLKHS_PERIOD);
I have some doubts here. According to specs:
UI - duration of any HS state on the Clock Lane,
TxByteClkHS - exactly 1/8 the High-Speed(HS) bit rate
I'd like to emphasize "BIT RATE" above (not clock rate).
In such case I would expect that ui2bc would take into account number of
lanes:
byte clock cycles = div_round_up(ui * dsi->lanes, 8)
So in case of one lane we need 8 ticks to get byte, and in case of 4
lanes 2 ticks are enough.
Am I correct, or I've missed sth?
> }
>
> /*
> diff --git a/drivers/phy/amlogic/phy-meson-axg-mipi-dphy.c b/drivers/phy/amlogic/phy-meson-axg-mipi-dphy.c
> index cd2332bf0e31..8a818cdb7606 100644
> --- a/drivers/phy/amlogic/phy-meson-axg-mipi-dphy.c
> +++ b/drivers/phy/amlogic/phy-meson-axg-mipi-dphy.c
> @@ -250,7 +250,8 @@ static int phy_meson_axg_mipi_dphy_power_on(struct phy *phy)
> (DIV_ROUND_UP(priv->config.clk_zero, temp) << 16) |
> (DIV_ROUND_UP(priv->config.clk_prepare, temp) << 24));
> regmap_write(priv->regmap, MIPI_DSI_CLK_TIM1,
> - DIV_ROUND_UP(priv->config.clk_pre, temp));
> + DIV_ROUND_UP(priv->config.clk_pre,
> + MIPI_DPHY_UI_PER_TXBYTECLKHS_PERIOD));
>
> regmap_write(priv->regmap, MIPI_DSI_HS_TIM,
> DIV_ROUND_UP(priv->config.hs_exit, temp) |
> diff --git a/drivers/phy/phy-core-mipi-dphy.c b/drivers/phy/phy-core-mipi-dphy.c
> index 288c9c67aa74..ccb4045685cd 100644
> --- a/drivers/phy/phy-core-mipi-dphy.c
> +++ b/drivers/phy/phy-core-mipi-dphy.c
> @@ -36,7 +36,7 @@ int phy_mipi_dphy_get_default_config(unsigned long pixel_clock,
>
> cfg->clk_miss = 0;
> cfg->clk_post = 60000 + 52 * ui;
> - cfg->clk_pre = 8000;
> + cfg->clk_pre = 8;
> cfg->clk_prepare = 38000;
> cfg->clk_settle = 95000;
> cfg->clk_term_en = 0;
> @@ -97,7 +97,7 @@ int phy_mipi_dphy_config_validate(struct phy_configure_opts_mipi_dphy *cfg)
> if (cfg->clk_post < (60000 + 52 * ui))
> return -EINVAL;
>
> - if (cfg->clk_pre < 8000)
> + if (cfg->clk_pre < 8)
> return -EINVAL;
>
> if (cfg->clk_prepare < 38000 || cfg->clk_prepare > 95000)
> diff --git a/drivers/phy/rockchip/phy-rockchip-inno-dsidphy.c b/drivers/phy/rockchip/phy-rockchip-inno-dsidphy.c
> index 347dc79a18c1..67b0a17be7e3 100644
> --- a/drivers/phy/rockchip/phy-rockchip-inno-dsidphy.c
> +++ b/drivers/phy/rockchip/phy-rockchip-inno-dsidphy.c
> @@ -364,7 +364,8 @@ static void inno_dsidphy_mipi_mode_enable(struct inno_dsidphy *inno)
> * The value of counter for HS Tclk-pre
> * Tclk-pre = Tpin_txbyteclkhs * value
> */
> - clk_pre = DIV_ROUND_UP(cfg->clk_pre, t_txbyteclkhs);
> + clk_pre = DIV_ROUND_UP(cfg->clk_pre,
> + MIPI_DPHY_UI_PER_TXBYTECLKHS_PERIOD);
>
> /*
> * The value of counter for HS Tlpx Time
> diff --git a/include/linux/phy/phy-mipi-dphy.h b/include/linux/phy/phy-mipi-dphy.h
> index a877ffee845d..ab1f736fbcd3 100644
> --- a/include/linux/phy/phy-mipi-dphy.h
> +++ b/include/linux/phy/phy-mipi-dphy.h
> @@ -6,6 +6,8 @@
> #ifndef __PHY_MIPI_DPHY_H_
> #define __PHY_MIPI_DPHY_H_
>
> +#define MIPI_DPHY_UI_PER_TXBYTECLKHS_PERIOD 8
Do we need to define it? I guess it is just BITS_PER_BYTE.
Regards
Andrzej
> +
> /**
> * struct phy_configure_opts_mipi_dphy - MIPI D-PHY configuration set
> *
> @@ -42,7 +44,7 @@ struct phy_configure_opts_mipi_dphy {
> * the transmitter prior to any associated Data Lane beginning
> * the transition from LP to HS mode.
> *
> - * Minimum value: 8 UI
> + * Minimum value: 8
> */
> unsigned int clk_pre;
>
More information about the linux-amlogic
mailing list