[PATCH v2] pwm: meson: external clock configuration for s4
Neil Armstrong
narmstrong at baylibre.com
Fri Jan 14 02:16:04 PST 2022
Hi,
On 14/01/2022 10:07, Jiayi.Zhou at amlogic.com wrote:
> From: "Jiayi.zhou" <jiayi.zhou at amlogic.com>
>
> For PWM controller in the Meson-S4 SoC,
> PWM needs to obtain an external clock source.
> This patch tries to describe them in the DT compatible data.
Can you be more explicit here ? On which SoC ? Why ?
As I understand while reading the S805X2 datasheet, now the PWM clock input is
done in independent CLKCTRL registers and no more in the PWM registers, right ?
So with S4, instead of passing the mux input clock of clkin0 & clkin1, now you pass
the PWM mux output clock.
>
> Signed-off-by: Jiayi.zhou <jiayi.zhou at amlogic.com>
> ---
> drivers/pwm/pwm-meson.c | 145 ++++++++++++++++++++++++++++++----------
> 1 file changed, 110 insertions(+), 35 deletions(-)
>
> diff --git a/drivers/pwm/pwm-meson.c b/drivers/pwm/pwm-meson.c
> index 3cf3bcf5ddfc..54db56c95be2 100644
> --- a/drivers/pwm/pwm-meson.c
> +++ b/drivers/pwm/pwm-meson.c
> @@ -51,6 +51,7 @@
> #define REG_MISC_AB 0x8
> #define MISC_B_CLK_EN BIT(23)
> #define MISC_A_CLK_EN BIT(15)
> +
> #define MISC_CLK_DIV_MASK 0x7f
> #define MISC_B_CLK_DIV_SHIFT 16
> #define MISC_A_CLK_DIV_SHIFT 8
> @@ -93,11 +94,13 @@ struct meson_pwm_channel {
> struct clk *clk_parent;
> struct clk_mux mux;
> struct clk *clk;
> + struct clk *clk_mux;
Why do you add a mux ?
> };
>
> struct meson_pwm_data {
> const char * const *parent_names;
> unsigned int num_parents;
> + unsigned int extern_clk;
> };
>
> struct meson_pwm {
> @@ -105,6 +108,7 @@ struct meson_pwm {
> const struct meson_pwm_data *data;
> struct meson_pwm_channel channels[MESON_NUM_PWMS];
> void __iomem *base;
> +
> /*
> * Protects register (write) access to the REG_MISC_AB register
> * that is shared between the two PWMs.
> @@ -130,13 +134,15 @@ static int meson_pwm_request(struct pwm_chip *chip, struct pwm_device *pwm)
>
> channel = &meson->channels[pwm->hwpwm];
>
> - if (channel->clk_parent) {
> - err = clk_set_parent(channel->clk, channel->clk_parent);
> - if (err < 0) {
> - dev_err(dev, "failed to set parent %s for %s: %d\n",
> - __clk_get_name(channel->clk_parent),
> - __clk_get_name(channel->clk), err);
> - return err;
> + if (!meson->data->extern_clk) {
> + if (channel->clk_parent) {
> + err = clk_set_parent(channel->clk, channel->clk_parent);
> + if (err < 0) {
> + dev_err(dev, "failed to set parent %s for %s: %d\n",
> + __clk_get_name(channel->clk_parent),
> + __clk_get_name(channel->clk), err);
> + return err;
> + }
> }
> }
>
> @@ -171,7 +177,11 @@ static int meson_pwm_calc(struct meson_pwm *meson, struct pwm_device *pwm,
> if (state->polarity == PWM_POLARITY_INVERSED)
> duty = period - duty;
>
> - fin_freq = clk_get_rate(channel->clk);
> + if (meson->data->extern_clk) {
> + fin_freq = clk_get_rate(channel->clk_mux);> + } else {
> + fin_freq = clk_get_rate(channel->clk);
> + }
> if (fin_freq == 0) {
> dev_err(meson->chip.dev, "invalid source clock frequency\n");
> return -EINVAL;
> @@ -228,17 +238,32 @@ static void meson_pwm_enable(struct meson_pwm *meson, struct pwm_device *pwm)
> struct meson_pwm_channel_data *channel_data;
> unsigned long flags;
> u32 value;
> + unsigned long set_clk;
> + u32 err;
>
> channel_data = &meson_pwm_per_channel_data[pwm->hwpwm];
>
> - spin_lock_irqsave(&meson->lock, flags);
> -
> value = readl(meson->base + REG_MISC_AB);
> - value &= ~(MISC_CLK_DIV_MASK << channel_data->clk_div_shift);
> - value |= channel->pre_div << channel_data->clk_div_shift;
> - value |= channel_data->clk_en_mask;
> - writel(value, meson->base + REG_MISC_AB);
> + if (meson->data->extern_clk) {
> + set_clk = clk_get_rate(channel->clk_mux);
> +
> + if (set_clk == 0)
> + dev_err(meson->chip.dev, "invalid source clock frequency\n");
> + set_clk /= channel->pre_div + 1;
> + err = clk_set_rate(channel->clk, set_clk);
> + if (err)
> + dev_err(meson->chip.dev, "%s: error in setting pwm rate!\n", __func__);
> + } else {
> + spin_lock_irqsave(&meson->lock, flags);
> +
> + value &= ~(MISC_CLK_DIV_MASK << channel_data->clk_div_shift);
> + value |= channel->pre_div << channel_data->clk_div_shift;
> + value |= channel_data->clk_en_mask;
> + writel(value, meson->base + REG_MISC_AB);
>
> + spin_unlock_irqrestore(&meson->lock, flags);
> + }
> + spin_lock_irqsave(&meson->lock, flags);
> value = FIELD_PREP(PWM_HIGH_MASK, channel->hi) |
> FIELD_PREP(PWM_LOW_MASK, channel->lo);
> writel(value, meson->base + channel_data->reg_offset);
> @@ -246,7 +271,6 @@ static void meson_pwm_enable(struct meson_pwm *meson, struct pwm_device *pwm)
> value = readl(meson->base + REG_MISC_AB);
> value |= channel_data->pwm_en_mask;
> writel(value, meson->base + REG_MISC_AB);
> -
> spin_unlock_irqrestore(&meson->lock, flags);
> }
>
> @@ -333,7 +357,8 @@ static void meson_pwm_get_state(struct pwm_chip *chip, struct pwm_device *pwm,
> struct meson_pwm *meson = to_meson_pwm(chip);
> struct meson_pwm_channel_data *channel_data;
> struct meson_pwm_channel *channel;
> - u32 value, tmp;
> + u32 value_pwm, value, tmp;
> + unsigned long gate_clk, fre;
>
> if (!state)
> return;
> @@ -341,30 +366,42 @@ static void meson_pwm_get_state(struct pwm_chip *chip, struct pwm_device *pwm,
> channel = &meson->channels[pwm->hwpwm];
> channel_data = &meson_pwm_per_channel_data[pwm->hwpwm];
>
> - value = readl(meson->base + REG_MISC_AB);
> -
> - tmp = channel_data->pwm_en_mask | channel_data->clk_en_mask;
> - state->enabled = (value & tmp) == tmp;
> -
> - tmp = value >> channel_data->clk_div_shift;
> - channel->pre_div = FIELD_GET(MISC_CLK_DIV_MASK, tmp);
> -
> + value_pwm = readl(meson->base + REG_MISC_AB);
> value = readl(meson->base + channel_data->reg_offset);
>
> channel->lo = FIELD_GET(PWM_LOW_MASK, value);
> channel->hi = FIELD_GET(PWM_HIGH_MASK, value);
>
> - if (channel->lo == 0) {
> - state->period = meson_pwm_cnt_to_ns(chip, pwm, channel->hi);
> - state->duty_cycle = state->period;
> - } else if (channel->lo >= channel->hi) {
> - state->period = meson_pwm_cnt_to_ns(chip, pwm,
> - channel->lo + channel->hi);
> - state->duty_cycle = meson_pwm_cnt_to_ns(chip, pwm,
> - channel->hi);
> + if (meson->data->extern_clk) {
> + gate_clk = clk_get_rate(channel->clk);
> + fre = gate_clk / (channel->lo + channel->hi);
> + state->period = div_u64(NSEC_PER_SEC, fre);
> + state->duty_cycle = div_u64(state->period * channel->hi, channel->lo + channel->hi);
> + tmp = channel_data->pwm_en_mask;
> +
> + if (((value_pwm & tmp) == tmp) && __clk_is_enabled(channel->clk))
> + state->enabled = true;
> + else
> + state->enabled = false;
> } else {
> - state->period = 0;
> - state->duty_cycle = 0;
> + tmp = channel_data->pwm_en_mask | channel_data->clk_en_mask;
> +
> + state->enabled = (value_pwm & tmp) == tmp;
> +
> + tmp = value_pwm >> channel_data->clk_div_shift;
> + channel->pre_div = FIELD_GET(MISC_CLK_DIV_MASK, tmp);
> +
> + if (channel->lo == 0) {
> + state->period = meson_pwm_cnt_to_ns(chip, pwm, channel->hi);
> + state->duty_cycle = state->period;
> + } else if (channel->lo >= channel->hi) {
> + state->period = meson_pwm_cnt_to_ns(chip, pwm, channel->lo
> + + channel->hi);
> + state->duty_cycle = meson_pwm_cnt_to_ns(chip, pwm, channel->hi);
> + } else {
> + state->period = 0;
> + state->duty_cycle = 0;
> + }
> }
> }
You need to rewrite the clock calculation entirely, instead of relying on a fin_freq, you need
to set_rate() the needed rate to the input clock, then calculate the periods on the rate
set by CCF.
One way is to forget trying to set a rate of the input clock, simply get_rate() of the input clock
and try to calculate periods on it.
Instead rely on assignes-clock-parent & assigned-clock-rate in DT to set the right parent of the mux
and rate of the mux post divider to feed to correct rate to the PWM controller.
>
> @@ -452,6 +489,10 @@ static const struct meson_pwm_data pwm_g12a_ee_data = {
> .num_parents = ARRAY_SIZE(pwm_g12a_ee_parent_names),
> };
>
> +static const struct meson_pwm_data pwm_meson_data = {
> + .extern_clk = true,
> +};
> +
> static const struct of_device_id meson_pwm_matches[] = {
> {
> .compatible = "amlogic,meson8b-pwm",
> @@ -485,6 +526,10 @@ static const struct of_device_id meson_pwm_matches[] = {
> .compatible = "amlogic,meson-g12a-ao-pwm-cd",
> .data = &pwm_g12a_ao_cd_data
> },
> + {
> + .compatible = "amlogic,meson-s4-pwm",
> + .data = &pwm_meson_data
> + },
> {},
> };
> MODULE_DEVICE_TABLE(of, meson_pwm_matches);
> @@ -534,6 +579,33 @@ static int meson_pwm_init_channels(struct meson_pwm *meson)
> return 0;
> }
>
> +static int meson_pwm_extern_init_channels(struct meson_pwm *meson)
> +{
> + struct meson_pwm_channel *channels = meson->channels;
> + struct device *dev = meson->chip.dev;
> + unsigned int i;
> + char name[255];
> +
> + for (i = 0; i < meson->chip.npwm; i++) {
> + snprintf(name, sizeof(name), "clkin%u", i);
> + (channels + i)->clk = devm_clk_get(dev, name);
> + if (IS_ERR((channels + i)->clk)) {
> + dev_err_probe(meson->chip.dev, PTR_ERR((channels + i)->clk),
> + "can't get device clock\n");
> + return PTR_ERR((channels + i)->clk);
> + }
> + snprintf(name, sizeof(name), "mux%u", i);
> + (channels + i)->clk_mux = devm_clk_get(dev, name);
> + if (IS_ERR((channels + i)->clk_mux)) {
> + dev_err_probe(meson->chip.dev, PTR_ERR((channels + i)->clk_mux),
> + "can't get device clock\n");
> + return PTR_ERR((channels + i)->clk_mux);
If you add mux you'll need to changes the bindings.
> + }
> + }
> +
> + return 0;
> +}
> +
> static int meson_pwm_probe(struct platform_device *pdev)
> {
> struct meson_pwm *meson;
> @@ -553,8 +625,11 @@ static int meson_pwm_probe(struct platform_device *pdev)
> meson->chip.npwm = MESON_NUM_PWMS;
>
> meson->data = of_device_get_match_data(&pdev->dev);
> + if (meson->data->extern_clk)
> + err = meson_pwm_extern_init_channels(meson);
> + else
> + err = meson_pwm_init_channels(meson);
>
> - err = meson_pwm_init_channels(meson);
> if (err < 0)
> return err;
>
>
More information about the linux-amlogic
mailing list