[PATCH v4 0/2] Meson GXL USB3 PHY driver

[Neil Armstrong]

On 03/03/2018 19:46, Martin Blumenstingl wrote:
> Amlogic Meson GXL SoCs use a dwc3 controller with two USB2 ports,
> Meson GXM SoCs use the same dwc3 controller but with three USB3
> ports enabled. Neither of these SoCs has any USB3 port enabled in
> the dwc3 registers.
> The second USB2 port on both SoCs supports host and peripheral
> (also called "device") mode.
> 
> The dwc3 controller supports host mode only. Peripheral mode is
> implemented through an additional dwc2 controller (which only enables
> device mode). The USB3 PHY has register bits which allow a driver to
> detect the current mode - however this is currently not implemented
> as the dwc2 controller seems to hang during reset (and I do not have
> a use-case where I need peripheral/device mode).
> 
> While the dwc3 controller has no USB3 port enabled we still need the
> USB3 PHY to be initialized, otherwise some boards (probably those where
> the bootloader does not initialize the USB3 PHY) show errors with
> high-speed USB devices connected to any of the USB2 ports. Configuring
> the USB_R1_U3H_FLADJ_30MHZ_REG_MASK register as it's done by Amlogic's
> vendor GPL kernel sources makes these error go away.
> 
> Thanks to Jerome Brunet for reporting the errors and Neil Armstrong
> for discovering that initializing the USB3 PHY fixes these USB errors!
> 
> 
> changes since v3 at [2]:
> - rebased on top of Kishon's linux-phy next branch (commit:
>   1f846be367fba4 "phy: allwinner: sun4i-usb: poll vbus changes on
>   A23/A33 when driving VBUS")
> - use SPDX-License-Identifier instead of the full license text
> 
> changes since v2 at [1]:
> - collected Rob's Reviewed-by on patch #1 and Yixun's Tested-by
> - rebased on top of v4.16-rc1 (no changes were required though)
> 
> changes since v1 at [0]:
> - document the interrupt in the dt-bindings patch (we don't use it in
>   the driver yet, but this interrupt is there so it should be
>   documented)
> - added the clock and reset lines, thank to Yixun Lan who gave me the
>   hints that these are needed (it's not clear when reading the Amlogic
>   GPL kernel sources, because the clock for example is always enabled
>   by hardware default, bootrom, etc..)
> - implemented the .set_mode callback
> - NOTE: I chose *NOT* to add Jerome's and Neil's Tested-by's as well as
>   Rob's Acked-by on the dt-bindings patch since I made changes that I
>   want to have reviewed again
> 
> 
> [0] http://lists.infradead.org/pipermail/linux-amlogic/2017-September/004780.html
> [1] http://lists.infradead.org/pipermail/linux-amlogic/2018-January/006290.html
> [2] http://lists.infradead.org/pipermail/linux-amlogic/2018-February/006449.html
> 
> Martin Blumenstingl (2):
>   dt-bindings: phy: Add support for the USB3 PHY on Amlogic Meson GXL
>     SoCs
>   phy: amlogic: add USB3 PHY support for Meson GXL and GXM
> 
>  .../devicetree/bindings/phy/meson-gxl-usb3-phy.txt |  31 +++
>  drivers/phy/amlogic/Kconfig                        |  12 +
>  drivers/phy/amlogic/Makefile                       |   1 +
>  drivers/phy/amlogic/phy-meson-gxl-usb3.c           | 282 +++++++++++++++++++++
>  4 files changed, 326 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/phy/meson-gxl-usb3-phy.txt
>  create mode 100644 drivers/phy/amlogic/phy-meson-gxl-usb3.c
> 

Hi Martin, Kishon,

Successfully tested on Amlogic Q200 Reference Design board with a Meson GXM S912 SoC.

Other patchsets included :
- improvements and fixes for the phy-meson-gxl-usb2 driver https://lkml.kernel.org/r/20180128202245.25021-1-martin.blumenstingl@googlemail.com
- DWC3 support for Amlogic Meson AXG and GXL SoCs V2 https://lkml.kernel.org/r/20180211211517.5846-1-martin.blumenstingl@googlemail.com
- initialize (multiple) PHYs for a HCD V11 https://lkml.kernel.org/r/20180303214309.25643-1-martin.blumenstingl@googlemail.com

Tested-by: Neil Armstrong <narmstrong at baylibre.con>

Kishon, This driver has been around for a long time now, can you take for the next release ?

Thanks,
Neil